Search Documents

By F. S. Hoseinian, D. Deglon, L. leal Filho, M. Safari, T. C. Souza Pinto

This paper investigates the effect of chemical and physical operational parameters on the reverse flotation of Timbopeba itabirite iron ore in a pilot-scale pneumatic flotation cell. Operational parameters include collector and depressant dosages, feed rate, superficial gas velocity and solids concentration. Results show that increasing collector dosage results in an increase in quartz recovery, particularly for the coarser quartz where recovery increases by nearly 30%. Increasing depressant dosage results in a decrease in both quartz recovery and hematite loss, for the coarser hematite particles. Increasing the feed rate has no effect on quartz recovery or hematite loss, suggesting that the pneumatic flotation cell is not residence time constrained. Increasing the superficial gas velocity results in an increase in quartz recovery to an optimum at a Jg of around 0.6 cm/s after which it decreases significantly, particularly for the coarser particles where recovery decreases by as much as 50%. Decreasing the solids concentration does not affect quartz recovery but results in significant decreases in hematite loss. Here, fine and coarse hematite loss decreases from around 25% to 12% and 10% to 2% respectively. Superficial gas velocity and solids concentration are operating parameters which have the largest effect on the flotation performance of the pneumatic flotation cell. Results suggest that this flotation cell should be operated at relatively low superficial gas velocities and solids concentrations. However, these are pilot-scale findings and would need to be tested at an industrial-scale where different operating conditions may be optimal. Keywords: Operational parameters, reverse froth flotation; entrainment; iron ore

Jan 1, 2020

By T. F. Cho, B .. O. You, K. S. Yoon, K. S. Won

Discontinuity Orientation Measurement (DOM) drilling system capable of retrieving the reference line-marked core log, which can be used for determining the relative positions and orientations of discontinuity planes along the borehole axis, has been developed. Accuracy of the borehole joints data measured from the reference-lined core and, eventually, the significance and applicability of DOM drilling system for site exploration are verified by comparing with the spatial characteristics of joints investigated by implementing borehole image-taking instruments in the same borehole. Enhancement of boring efficiency has been also confirmed by performing twin drilling operations, one with DOM drilling system and the other with a conventional drilling machine equipped with D-3 core barrel, on two neighbouring sites of 5 m apart. Ein DOM(Diskontinuitätsorientierungsmessung)-Bohrsystem, das durch Grundlinien markierte Bohrprobelog extrahieren kann und die relativen Lagen und die Orientierungen der sich im Bohrloch verbreitenden Flächen bestimmen kann, ist entwickelt worden. Die Wichtigkeit des DOM-Bohrsystems und dessen Anwendbarkeit auf die Erforschung auf dem Bohrplatz werden dadurch bewiesen, dass man die Genauigkeit der Daten der Bohrlochsspalte, die durch die die Grundlinie zeichnende Bohrprobe gemessen werden, mit dem räumlichen Eigenschaften der Spalte vergleicht, die durch die Bildaufnahme des gleichen Bohrlochs nachgeforscht werden. Un system de sondage, Discontinuity Orientation Measurement (DOM), capable de récupérer des carottes markés en une ligne de référence a été dévelopé. Il peux être utilisé pour déterminer les positions relatives et les orientations des plans de discontinuité le long de l’axe de trou de sonde. Leur signification et applicabilité pour une caractérisation de site est verifiée par une comparaison de la précision des données a propos des joints mesurés a partir des carottes markés et les carac-téristigues spatiales des joints enquêtés par le camera de sondage

Jan 1, 2003

Sampling In The Coal Industry Exploration, Mine, Met and Environmental Sampling EMMES 2005 3, 4 November 2005

Jan 1, 2005

By Matthew D. Viergutz

MECS? HRS technology has reliably recovered intermediate pressure steam from sulphuric acid plants for more than 20 years. This steam can either generate electricity or replace steam produced by an existing fuel-fired boiler. As worldwide greenhouse gas emissions continue to rise, industries are looking for novel and cost effective solutions to reduce pollution, particularly carbon dioxide, from their plants. Waste heat recovery technologies such as HRS offer new and existing plants the opportunity to maximize energy efficiency while reducing their reliance on energy supply from external sources. This paper offers a unique look at energy recovery in sulphuric acid plants and how recent innovations in MECS? Heat Recovery System technology make HRS more financially viable ? and more green - than ever.

Jan 1, 2009

By N. X. Feng, S. G. Zhou, X. L. Wu, J. P. Peng, Y. Z. Di

"Szaibelyite–suanite type ore is rich in magnesium oxide and boron oxide. We propose a new method to extract both metallic magnesium and valuable residues rich in boron by reduction using metallic aluminium.Thermodynamic analysis of the reactions between aluminum and MgO, Mg2B2O5, and Mg3B2O6 was carried out. The effects of CaF2 addition, temperature, mass of Al, and pellet formation pressure on the extraction of magnesium were also investigated experimentally.The results indicate that the magnesium oxide phase can be displaced from 2MgO-B2O3 and 3MgO·B2O3 by CaO in the reduction system. The reduction ratio of magnesium oxide was 38% without calcium fluoride addition, increasing to 94% with 5.1% calcium fluoride. The reduction ratio increased with increasing temperature and mass of Al. To obtain a higher reduction ratio, the reduction pellet should be formed under a reasonable pressure.IntroductionBoron and its compounds are widely used in textiles, borosilicate glass, metallurgy, fertilizers, and nuclear shielding. Boron resources are mainly found in Turkey, the USA, Russia, and China. In Liaoning, China, there are abundant szaibelyite–suanite type ores that are rich in magnesium oxide and boron oxide. Szaibelyite and suanite ores are used to produce borax by a carbon dioxide– soda process. Annually, 2 Mt of waste materials containing 3–20% B2O3 and 2–25% MgO are produced during the process. It is necessary to make use of these waste materials containing high concentrations of boron oxide and magnesium oxide to avoid environmental problems as well as for economic reasons (Ozdemir and K1pcak, 2007)"

Jan 1, 2016

By Matthew D. Viergutz

MECS? HRS technology has reliably recovered intermediate pressure steam from sulphuric acid plants for more than 20 years. This steam can either generate electricity or replace steam produced by an existing fuel-fired boiler. As worldwide greenhouse gas emissions continue to rise, industries are looking for novel and cost effective solutions to reduce pollution, particularly carbon dioxide, from their plants. Waste heat recovery technologies such as HRS offer new and existing plants the opportunity to maximize energy efficiency while reducing their reliance on energy supply from external sources. This paper offers a unique look at energy recovery in sulphuric acid plants and how recent innovations in MECS? Heat Recovery System technology make HRS more financially viable ? and more green - than ever.

Jan 1, 2009

By R. Thomas

A Honeywell TDC 2000 central process control system was installed at Rössing in 1984. The system controls the metallurgical operations from crushing to the finished product of uranium oxide and manufacture of sulphuric acid. The operation was previously controlled from nine separate local control rooms. The paper briefly reviews the design and commissioning of the control system on an operating plant and discusses the impact on manpower organisation and training needs. Development of the process control system during its first two years of operation is reviewed and a summary is given of the current status of computer control at Rössing. The impact of the new system on overall plant operation and performance efficiency is also briefly described. In conclusion, future developments of computer control and overall optimisation of metallurgical operations are reviewed.

Jan 1, 1987

Professor R. N. Pryor, AR.S.M., B.8c., C.Eng., F.I.C.E., F.I.Min.E., F.I.M.M., who died on 14th July, 1979, after a short illness, was President of the Institution of Mining and Metallurgy for the session 1978-1979. Weld pool metallurgy A high level of current interest in welding characteristics and behaviour and in the properties of welds was amply demonstrated by the large attendance at The Welding Institute's 1978 Conference on 'Trends in Steels and Consumables for Welding' and by the overwhelming number of papers offered for the International Conference on 'Arc Physics and Weld Pool Behaviour' in May 1979. Mine ventilation The First International Mine Ventilation Congress was held in September, 1975, in Johannesburg, South Africa, at the University of the Witwatersrand. It was organized by the Mine Ventilation Society of South Africa. Occupational accidents and diseases The IXth World Congress on the Prevention of Occupational Accidents and Diseases will be held in Amsterdam from 6th to 9th May, 1980. Rock mechanics The 21st U.S. Symposium on Rock Mechanics is to be held at Rolla, Missouri, from 27th to 30th May, 1980. Protection against noise An International Symposium on the Protection of Workers Against Noisewill be held in Dresden (German Democratic Republic) from 27th to 30th November, 1979. Management of mineral resources A joint meeting of the Institution of Mining and Metallurgy, the Society of Mining Engineers of AIME, and the Metallurgical Society of AIME is to be held in London from 27th to 30th May, 1980. INFACON 80 During 1970 various South African institutes and associations agreed to organize an international ferroalloys congress. It was recommended that this should be made a continuing forum, where ferroalloy people could meet and discuss matters of mutal interest.

Jan 1, 1979

By D. D. Aksenova, V. A. Ignatkina, L. A. Samatova, A. V. Lygach, E. D. Shepeta

Calcium minerals such as scheelite, phosphate, apatite are valuable minerals, which have similar flotation properties to the calcium gangue minerals. An additional problem is the fine dispersion and close mineral association of valuable and other minerals. Low polar compounds (non-ionic surfactant), such as fatty iso alcohols, neonol and phosphol, and their combinations with sodium oleate have been studied using flotation of monominerals and ore flotation; ATR IR spectroscopy and TEM for study surface of minerals; UV spectroscopy for control solubility, aggregation and de-aggregation processes. Increase in solubility of fatty acid collectors was confirmed by low soluble (heteropolar) compounds. Oxyethylated esters of phosphoric acid are adsorbed on phosphorite by -O2PO2R2 and on other rock minerals by donation of OH bond. Same effect shows difference of adsorption of fatty iso alcohols on calcite and scheelite. The different forms of adsorption of ionic and nonionic compound on a sparingly-soluble mineral surface creates distinction of the flotation kinetics and technological balance of ore flotation. The results of the separation of flotation of scheelite from calcite depend on the order of pouring into pulp of fatty iso alcohols and oleate, and their ratio in the mixture. Increasing scheelite recovery into rougher scheelite concentrate by 3.6% for both the flotation and sludge classes was obtained. Calcite recovery varied slightly upwards or downwards by 0.8-2.4%. The use of the non-ionic surfactant phosphol in combination with a fatty acid soap allows for obtaining a phosphate concentrate with more than 28% P2O5 content and almost 80% recovery in flotation operation. It is not obtainable with other reagent regimes. Keywords: Flotation, calcium minerals, oleate, fatty isoalcols, neonol, oxyethylated esters, adsorption

Jan 1, 2020

By J. A. L. Napier

One of the most important characteristics of tabular mine stress analysis is the need to represent the complex evolution of mining face positions and the accompanying induced stress changes in the rock mass. Integration of seismic activity with numerical modelling requires flexible and efficient solution schemes in which both off-reef damage and large-scale fault slip can be effectively represented. A new approach is investigated in which the stope closure and ride variables can be found using a moving least squares estimator. Some advantages of this approach over traditional element-based tessellation schemes are identified. At the same time, shortcomings of this method are noted when the displacement discontinuity variable is approximated by a polynomial shape function. Difficulties and possible solutions to the shape function formulation near excavation edges are discussed. Une des caractéristiques les plus importantes de l’analyse des contraintes minières tabulaires est la nécessité de représenter la complexe évolution des positions du front de taille et des changements concomitants des contraintes occasionnées dans la masse rocheuse. L’intégration de l’activité sismique avec la modélisation numérique requiert des projets souples et efficaces qui permettent la représentation des dommages hors-filon et des glissements de faille à grande échelle. Une approche nouvelle est étudiée qui permet de trouver la fermeture de la taille et les variables de montage en utilisant un estimateur par les moindres carrés mobile. Certains des avantages de cette approche sur les traditionnels projets basés sur une structure en mosaïque sont identifiés. En même temps, les défauts de cette méthode sont notés lorsqu’on calcule la variable de discontinuité du déplacement approximativement par une fonction de forme polynomiale. Les difficultés et solutions possibles à la formulation de la fonction forme près des bords d’excavation sont discutés. Eine der wichtigsten Charaketeristika der taublaren Grubenspannungsanalayse ist die Notwendigkeit, die komplexe Entwicklung der Abbaupositionen und der damit verbundenen induzierten Spannungsänderungen der Gesteinsmasse neu vorzulegen. Die Integration der seismischen Tätigkeit mit einem numerischen Modell erfordert flexible und effiziente Lösungsschemata, in denen sowohl Schäden ausserhalb des Riffs als auch Verwerfungen großen Ausmaßes effektiv dargestellt werden. Ein neuer Vorstoß wird untersucht in welchem die Strossenschliessung und Schneisenvariablen unter Verwendung des Schätzwertes der kleinsten quadratischen Abweichungen (Gaussscher Schätzwert) gefunden werden. Einige Vorteile dieser Annäherung im Vergleich zu der traditionellen Element-basierenden Tessellation sind identifiziert. Gleichzeitig werden Unzulänglichkeiten dieser Methode vermerkt, wenn die Verschiebungsdiskoniuitätsvariable durch eine polynomische Formfunktion angepaßt wird. Schwierigkeiten und mögliche Lösungen zur Formfunktionsformulierung nahe Exkavationsrändern werden besprochen.

Jan 1, 2003

"Chairman: Professor J. C. Griffiths Rapporteur: Mr J. P. G. PRETORIUSPapers:Mine-mill production scheduling by dynamic programming by R. J. Roman Optimization of a large mining venture by J. C. Paynter, B. K. Loveday and C. G. Robinson Economic surface mining of multiple seams by T. V. Falkie and W. E. PorterIn introducing his paper, Mr Roman said that whereas in manufacturing plants the yearly production levels were usually chosen to produce the largest annual cash flow, in a mining operation, the raw materials (ore) were exhaustible so that the production had to be scheduled to maximize the total net present worth of the operation. This optimum production schedule could be determined by using dynamic programming. The required information was readily available to management at most mines. The 'possible operating range' of production rates lay between the rate with the highest profit per ton. and that with the highest profit per year. The optimum production rate started typically at the top of this range and decreased slowly as the deposit was depleted.Dynamic programming was used to determine several production schedules for a hypothetical mine-mill complex. The effects of changes in the ore grade estimates, size of deposit and acceptable rate of interest on the production schedule were taken into account. Apart from the fact that the net present worth of the overall profits was larger than that obtained by conventional methods, it appeared from the cases studied that the amount of metal recovered was also greater.Dr it P. King commented that this was a very interesting application of dynamic programming. He pointed out, however, that the market price of the metal was likely to vary significantly and randomly during the life of the mine, and he suggested that the problem should, therefore, be reformulated as a stochastic dynamic programming problem.If the price of the metal rose to abnormally high levels, a much higher than normal production rate could be expected. The results of analyses given in Table 5 showed that the production rate was a function of market price. In his view the stochastic problem could be solved just as easily as the deterministic problem.In reply to a question by Dr King as to whether the function relating recovery to production rate (Table I) was based on real data, the author replied that it was based on the results of an analysis conducted at the Union Carbide Corporation's Pine Creek tungsten mine in California.Dr D. M. Hawkins stated that costs were incurred when the production rate was altered, for example, in appointing or laying off staff, and that in practice it may be necessary to take these costs into account in finding the optimum production rate. Mr Roman replied that, while normal administrative costs were accounted for, the additional costs incurred in appointing and laying off staff were not taken into account."

Jan 1, 2014

By J. Ning, T. Bu, J-Q. Jiang, L. Jiang

"In coal mining in China, the cutting height of the shearer in longwall faces is increasing. Owing to the increase of extraction height, the caved roof strata area is enlarged, and new issues are being encountered, such as determination of a suitable working resistance for the shield and control of the roof. Through field observation and theoretical analysis of the first longwall face with a height of 6.0 m in the Bayangaole mine, a three-stage structural model was developed. Stage I is defined as the period in which the lower immediate roof (LIR) caves into the goaf and is broken into irregular shapes of various sizes. Stage II is defined as the period in which the upper immediate roof (UIR) breaks and impacts the LIR. In stage III, the main roof breaks into blocks and then impacts the UIR. With respect to these three stages, a suitable method was identified for calculating the working resistance of the shield support for a super-great mining height longwall face (SGMHLW). Introduction and backgroundThe coal seams in the Shendong coalfield, located in the northwest of China, are characterized by low dips and large thicknesses and are thus suited for full thickness extraction. Since the mid-1990s, the Shendong coalfield has been developed into one of the largest in the world (Ning, Liu, and Tan. 2014; Ning et al., 2017). Recent developments in mining equipment have made it possible extract entire seams up to 5.0 m thick in a single cut. This method, termed the ‘super-great mining height longwall face’ (SGMHLW) method, has been widely adopted in the Shendong coalfield (Table I) (Ju and Xu, 2013; Peng, Li, and Zhou 2015; Zhang, Fan, and Ma 2011). According to some studies, sudden support-closure incidents often occur when using the SGMHLW method. The key to solving this engineering issue is to have a clear understanding of the structural characteristics and movement laws of the overlying strata. For instance, the load on the supports is related to the movement of the roof stratum as a response to the mining activities."

Nov 1, 2018

By J. O. Mogalanyane, N. Naudé, A. M. Garbers-Craig

The fines produced is not suitable as feed material for the subsequent rotary kiln and the electrical arc furnace. The need for briquetting the ferronickel ore is premised on the minimisation of fine particles in the rotary kiln as well as improving charge permeability in the furnace, and improving overall process safety. Briquetting may be defined as an agglomeration method in which fine particles are compressed under pressure. It consists of three different technologies: vibropressing, roller pressing and stiff extrusion. The current study focuses on evaluating the performance of ferronickel briquettes generated, using roller-pressing technology. Physical properties, chemical properties and metallurgical properties of the briquettes were used to evaluate their performance and quality. Standard ISO tests for iron ore pellets were used. Size degradation as a result of reduction was measured using the ISO 4696-1 test. The decrepitation of the briquettes at the point of entry into the rotary kiln was evaluated using the ISO 8371 test method at a temperature of 700oC. The degree of reduction was evaluated using the ISO 4695 test procedure. Average green briquette compressive strength of 559 N was reported at a moisture content of 16% with an average drop number of 19.1. Increasing the moisture content has a detrimental effect on both the compressive strength and the green briquette yield. The drop number is expressed as the number of drops until breakage, when a briquette is dropped from a 1 m height, decreased with an increase in moisture content. At a moisture content of 16% an average green briquette yield of 85.1% was reported. Keywords: Ferronickel briquettes, moisture content, curing conditions, physical properties, chemical properties

Jan 1, 2020

"Chairman: Mr R. A. PLUMBRIDGE Rapporteur: Dr D. M. HAWKINSPapers:The relevance of computer methods to the economics of the mineral industry by R: A. PerlmanDynamic control of a mining enterprise by R. G. CoyleAn economic model of the mineral sands industry by G. P. A. HoweMr M. Splaine, in opening the discussion on Mr Perlman's paper, asked whether the model, as fitted by data up to 1963, predicted the rise in the price of copper in 1967, and whether the model could be used to capitalize on short-term price fluctuations.Answering the second question first, Mr Perlman said that the horizon used is six months to one year. In the very short term the activities of speculators obscured the effect of the fundamental econometric variables. This effect, however, was removed if one moved to a longer term, say, quarterly. In 1963 the model had predicted a price rise in 1964 and 1965 and a drop in price in 1966. The rise in 1967 had been caused by a strike, and imponderables such as large strikes were difficult to include in the model since they were unpredictable. Model simulation can be used to show the effect of strikes on price and the effect of small strikes is small.Mr B. R. van Rooyen said that because models are both calibrated and tested on historical data a bias was introduced which gave rise to an overoptimistic estimate of the accuracy of the forecasts. To this Mr Perlman replied that there seemed to be no alternative to the use of historical data for calibrating and testing models, and thus little hope of avoiding the bias. A second point made by Mr. van Rooyen was that manage¬ment tended to be suspicious of complex models and that frequently more heuristic models were sufficiently accurate and preferable for investment decisions. He added that if management were not involved in the model building the econometrician might easily go astray, Mr Perlman replied that symbiosis between data analysts and users of the model was essential and that the experience of the practitioner must be reflected in the model.Mr M. R. Fuller-Good remarked that a clear understanding of future price trends was essential for effective capital planning, and asked, first, how one went from the compiled data on supply and demand to the determination of their effect on price, record, whether necessary data, for example, capacities, could be obtained timeously, and, third, when strikes restricted supply, whether stockpiling by consumers induced large price fluctuations."

Jan 1, 2014

By J. Levin

Bond's Standard Work Index (SWi) indicates the grindability of an ore, and his Operating Work Index (OWI) indicates the performance of a grinding mil or circuit. The comparison of the two indices offers a measure of the efficiency of the grinding operation. Mil (or circuit) performance, particularly on the Witwatersrand, is often indicated by the index kilowatt -hours per tonne of minus 75 µm material produced (kWh/t minus 75µm or OE75)' The paper shows that a standard kWh/t minus 75 µm index (SE75) can be obtained from the standard Bond grindability test (which provides the SWi), and asks whether the two E75 indices can be used in the various ways in which the two Work Indices are used. For the answer, the paper presents averaged values for the standard grindability indices of the gold ores of the Witwatersrand, averaged values for the performance of grinding mils operating on those ores, and the results of laboratory grinding tests on a composite of several Witwatersrand ores. The particle-size indicator for the calculation of the Wi indices, the am size, is constant in its relation to the largest particles present, whereas the percentage minus 75 µm, the indicator of size for the E75 index, varies with the degree of grinding in its relation to the size of the largest particles. Because of this difference, the standard Work Index increases as the grind becomes finer, whereas the standard kWh/t minus 75 µ value decreases. The Wi and E75 indices nevertheless serve similar purposes when applied to moderately fine grinding-finer than 70 per cent minus 75 µm. Open circuit laboratory grinding tests revealed three stages in the grinding process, and credible values for the open circuit Work Index were obtained only from the second stage. The conversion of the open circuit Work Indices to the equivalent of close circuit indices by the application of Bonds open circuit inefficiency factor (a constant for grinds indicated by the d80 size) was of limited success; however, the development of a conversion factor related to particle-size should not be difficult. Initially difficulty was experienced in the calculation of the 0E75 indices from the results of the laboratory tests, but it was eventually considered that a constant value of the index derived from the results would be close to the true open-circuit index. The open-circuit grinding test could there fore be a convenient method for the detection of differences in the grindability of ores.

Jan 1, 1992

By F. Nakhaei, A. Noury, S. Ghodrati

To achieve maximum efficiency in any purification stage, the flotation should be continued until the concentrate grade reaches the feed grade. During sampling from rougher cells of the Iranian Sarcheshmeh copper concentrator plant 1, it was revealed that the concentrate grade of the last five cells of rougher circuit was close to feed grade. Therefore, it was suggested that the concentrate of the aforementioned cells be mixed with rougher feed. In this study, one of eight rougher circuit rows was selected and evaluated. The floatability tests were performed to compare the flotation behaviour of rougher feed and mixture of concentrate of the last five cells with rougher feed in the laboratory scale by a tree analysis process. The results showed that mixing of rougher last five cell concentrate with feed has a detrimental effect on flotation efficiency that leads to a 3% decrease in recovery. It was also observed that with grinding of this concentrate, recovery can be improved. Keywords: Efficiency, flotation, rougher, tree analysis, floatability, concentrate, mixing

Jan 1, 2020

By P. F. Ledwaba

"Artisanal and small-scale mining (ASM) in South Africa received official recognition after the change in government in 1994.The Reconstruction and Development Programme (RDP) recognized the sector as a vehicle for social and economic development for historically disadvantaged South Africans (HDSAs) who had previously been excluded from participating in the mainstream economy. Having recognized the ASM sector, government introduced several interventions and support structures to foster the development of ASM, to encourage participation of HDSAs, and to address challenges facing the sector. The objective of this paper is to assess the progress made, with particular regard to challenges in the sector. The paper focuses on the policy requirements that were deemed important for the growth of the ASM sector by the White Paper on Minerals and Mining Policy (1998). These can be collated into five categories: access to mineral rights, access to finance, access to markets, technology and skills, and institutional support. The paper provides a review of the support interventions, their intended roles and impact on the sector, and identifies existing gaps and possible ways of dealing with the challenges. There is a need for research to assess the real impact of these past and existing interventions on the ASM sector to draw lessons for future development.IntroductionThe significant rise in artisanal and smallscale mining (ASM) activities worldwide has led to many countries recognizing the sector. ASM takes place in approximately 80 countries (World Bank, 2013). It is estimated that the sector employs between 20 and 30 million people around the world (Buxton, 2013). This compares to between 3 and 3.7 million in 1999 (International Labour Organization, 1999). ASM activities are widespread, occurring mostly in developing countries in Africa, Asia, Oceania, and Central and South America (World Bank, 2013). There has been a significant increase in the number of people participating both directly and indirectly in the sector and this is expected to continue given the socio-economic realities of most developing countries. High levels of poverty and unemployment and growing inequality continue to be largest problems facing the majority of developing countries today. The ASM sector plays an important role as a source of livelihoods, particularly for those residing in rural areas with limited economic opportunities. In the majority of countries, the recognition of the ASM sector was driven by its increasing contribution to socio-economic development through job creation, poverty alleviation, and rural development. In response, a number of intervention strategies were introduced in support of the sector to address its negative impacts and to increase its potential benefits."

Jan 1, 2017

By P. de A. Barbosa, M. G. Bergerman, E. da Fonseca

Located in the state of Pará, Brazil, the Sossego copper and gold mine consists of a heterogeneous geological deposit. Its complexity derives from the hydrothermal alteration, the ore-forming event, which modified the host rocks, such as granite, and metamorphosed volcanic rocks into several mineral assemblages. Different mineral assemblages have led to differences in abrasiveness. A few Bond abrasion tests conducted during the mine feasibility study did not provide a robust abrasiveness database, thus the variation of physical properties for some mineralisation host rocks was not possible. Although several test methods may be used to determine ore abrasiveness, the Bond method is the one most commonly used in the mining industry. Despite being simple to carry out, this test method has certain limitations as to particle size and the amount of ore sample required, which often makes it difficult or even impossible to apply in the early stages of a project and in geometallurgical studies. The Laboratoire Central des Ponts et Chaussées (LCPC) test may provide an alternative, as it requires a smaller amount of fine-grained material. This study aimed to provide data on wear properties of various ore types from Sossego mine using the LCPC method. It included validation for 40 different ore samples using the Bond test as a benchmark. The results showed good correlation, indicating it may be possible to use the LCPC test as an alternative to the Bond abrasion test. A high abrasiveness index was found for acid metavolcanic rock, confirming the results observed in Sossego mill’s operating database, pointing to a mineralogical drive to amorphous quartz. Keywords: Abrasiveness, geometallurgy, copper ore, Bond abrasion test, LCPC

Jan 1, 2020

[Consider the situation where we wish to estimate the value of a block of ore W from the values of n samples wt (i = 1, 2.... n). The samples can be located anywhere inside or outside W. The blocks and the samples can have any size or shape (Fig. 8.1). We define ws as the set of all the samples wi: WS = Iw1; W2; W3.. . wn and we wish to estimate the block W using the samples ws. Let xi be the value of the ith sample and µw the unknown average value of the block. We can estimate µw from the average value of all the samples. Let µw be the estimator of µw. As the samples need not be of equal size, the sample average is: µw = wi xi/~ wi. (8.1) The mean squared error made when estimating µw by µw is known as the variance of estimation of W by ws. It is the error made when giving the value of the sample set ws to the block W and is written o2E (WS to W). By definition: o2E (ws to W) = E [(µw - µw)2]. (8.2) If n = 1, this error is known as the extension variance. Since the sum of the weights given to the sample values is equal to 1,0, the estimator µw is unbiased (the question of the absence of bias is studied in more detail in Chapter 9): E [( µw - µw)1 = 0. (8.3) The error (µw - µw) has zero mean and a variance o2E = E (W8 to W). If we assume that this error is normally distributed, we can define confidence limits for µw. Let tP be the value of the standardized normal variance t such that the probability that t is less than tP is p: (t,) = .\/27T f exp (- t2/2) dt = p (8.4) The probability that µw is larger than µw + t1-P oE is p. The probability that µw is smaller than µw- t1-P oE is p. The following approximation formulae are often used to calculate 2p central confidence limits for the block value: 68% central confidence limits (p = 16%): µw - o2E, and µw + o2E. 95 % central confidence limits (p = 2,5 %): µw - 2 oE, and µw + 2 oE. Tables of the function 0 can be found in any textbook on statistics (for example, Fraser, 1958, p. 388) (see Table 7.2). [ ] The last line of Table 2.2, corresponding to f = 00, also contains the value of tP for p = 80, 90, 95 and 97,5 %.]

Jan 1, 1978

By C. A. Jermy, B. J. Venter

Excessive build-up of methane and water pressures was identified as the leading cause of some Q/the roof falls in a coal mine in the eastern Transvaal. In order to characterize the migration of the methane and water into and around the mined coal seam, a laboratory investigation of the permeability of the roof strata was undertaken. The aim of the investigation was to correlate changes in the fades with changes in permeability to enable the prediction of possible zones of pressure buildup. The tests were carried out on samples from borehole core that had been obtained from the roof strata as part of the mine exploration programme. Permeability measurements were then conducted under atmospheric and triaxial-stress conditions. For the tests under atmospheric conditions, a modified Ohle cell was used and, for the tests under triaxial-stress conditions, a modified Hoek cell was used. The liquid equivalent permeability?s of the different samples were obtained by use of ASTM D4525- 85, and these were then used as a basis for comparison. Facies type, i.e. grain size, was found to have an influence on the permeability but, owing to the variable nature of the sediments, a range of permeability rather than a specific permeability value was associated with each type of Jades. The measured permeability was bound to decrease with an increase in gas pressure. The liquid equivalent permeability was bound to increase with an increase in grain size for the coarser-grained Jades, and to decrease with an increase in grain size for the finer-grained types. The application of an external stress regime to the sample was bound to reduce the permeability, but the amount of the reduction depended on the type of stress. The permeability was also found to depend on the recent stress history of the sample. The authors conclude that the methods described are useful for the correlation of facies type with permeability, but that the results are sensitive to changes in locality.

Jan 1, 1994