Search Documents

By M. Abdellatif

Keywords: Magnesium, pyrometallurgy, Mintek Extensive testwork on atmospheric thermal magnesium production has highlighted certain important fundamental and operational factors that have a major influence on magnesium extraction and its extraction rate, the condensation efficiency of magnesium, as well as on the quality of the condensed metal. The possible impact of these factors on the selection and preparation of raw materials, recipe choice, furnace electrical energy consumption, and on the refining requirements of the crude magnesium is discussed. Selected pilot plant operational and metallurgical data are also presented.

Jan 1, 2006

By A. P. N. Sutherland

Pipelines for transporting high concentration slurries are often designed using methods applicable to homogeneous non-Newtonian laminar flow. Many industrial slurries though comprise coarse particles in a non-Newtonian carrier fluid, and existing experimental evidence from tests with such slurries demonstrates that they are not homogeneous. Under laminar shear conditions the coarse particles settle, even in statically stable carrier fluids. To understand this better, the Institute of Materials Science and Technology (IMST) at Cape Peninsula University of Technology (CPUT) is conducting ongoing research into the flow of these high concentration non-Newtonian settling slurries. Since pressure gradient and flow rate measurements alone are insufficient to adequately model the flows, an electrical resistance tomography (ERT) instrument developed by the University of Cape Town (UCT)was incorporated into the pipe test loop to determine pipe cross-section concentration and velocity profiles. The software developed to do this is modular and allows different image reconstruction and cross-correlation algorithms to be implemented and tested without significantly changing the rest of the application. At a total frame capture rate of 566 frames/sec a 2.67 GHz Intel Celeron processor with 500 MB of RAM is fast enough to calculate and display velocity profiles in ?real-time? at an update rate of one profile every two seconds. Examples of experimental concentration and velocity profiles obtained using the system are shown and some proposed improvements/extensions to the system are listed.

Jan 1, 2008

By Fadeela Saloojee, Frank K. Crundwell

"Pressure leaching is an option for copper recovery from chalcopyrite. Leaching takes place at high temperatures and pressures in the presence of an oxidising agent. This work shows how the performance of pressure leaching circuits may be improved by optimising the configuration of autoclaves and the heat-removal method. The objective was achieved by creating an autoclave model by combining mass balances, energy balances and population balances. A base-case circuit consisting of a single autoclave was chosen, and this base case was compared with options for increasing capacity by adding more autoclaves to the circuit. These capacity–increase options include circuits in which the additional autoclave is added in parallel, in series and in series with thickening between the two autoclaves. The copper extraction, productivity and cooling requirements for these options are compared. The series circuit with inter-stage thickening has the highest extraction and productivity, however, the cooling duty in the first autoclave is high. In addition to comparing circuit options, three options for heat removal were investigated: cooling coils, quench water and flash recycling. The flash-recycle option results in the highest copper extraction, and the quench-water option gives the lowest copper extraction. INTRODUCTION Background Copper sulfide ores and concentrates containing chalcopyrite are typically hard to leach under atmospheric conditions. Smelting of these ores may also be a challenge, due to the inability of smelting processes to handle low-grade ores, as well as impurities such as arsenic and antimony. Alternative hydrometallurgical routes to treating chalcopyrite are therefore required. One option is pressure leaching, which is the focus of this work. In the pressure leaching process, sulfide ores and concentrates are leached in autoclaves at temperatures of 200 to 220°C and a pressure of about 3000 kPa (Schlesinger et al., 2011). An oxidising agent, usually oxygen, is required to oxidise sulfide ions to sulfate ions. The oxidation of sulfur to sulfate is exothermic; consequently, a method of heat removal is necessary in order to maintain the temperature in the autoclave."

Jan 1, 2015

Foamed cement packs offer a viable alternative to conventional timber or other forms of packs for permanent underground support. These packs comprise steel mesh and hoop containment with an outer bag for the grout; woven, laminated polypropylene fabric being ideal for the purpose. The grout is supplied in 25kg bags and fed into a purpose ? designed foam placer machine which delivers the foamed grout directly to the packs from 60 metre long delivery hose. Foamed cement grout as a fill material offers attractive properties for support packs, in summary these are: Variable Grout Strength Grout strength is controlled by the grout density being delivered from the placer machine. This can be changed by the machine settings. Strength Development Fast rate of strength development is possible so that support is available quickly. Pack yield The foamed grouts are compressible so that yielding of the grout pack can be achieved without loss of support. Rate of Filling Three sizes of placer machine are available, these use one, two, or three 25kg bags per minute of grout, pack filling time is therefore a matter of minutes, a typical 0.75m diameter pack x 1.2m high taking some 17 minutes to fill. Tests in a 1000 tonne press have confirmed that the above characteristics can be achieved with foamed cement packs at acceptable cost. This will be illustrated in the paper with experience to date.

Jan 1, 2008

By E. D. Musin, S. S. Gudkov, A. V. Epiforov, S. V. Balikov

The standard technology for processing of gold-bearing sulfide raw material has many problems associated with the use of cyanide as a gold lixiviant. Therefore, many tests to find alternative gold recovery methods are being undertaken. This paper describes some technological solutions, which can become alternatives to cyanide technology in the future. Pressure oxidation (POX) of refractory gold-bearing sulfide concentrates from five different Russian gold deposits were investigated. Concentrate 1 was gold-copper concentrate. Concentrate 2 was gold-pyrite concentrate. Concentrates 3-5 were pyrite-arsenopyrite double refractory concentrates. The POX tests were at temperatures of 110, 200 and 220 °C and oxygen pressures of 1.5, 2.4 and 3.0 MPa were carried out. Gold lixiviants, such as chloride, thiosulfate, sulfite and thiocyanate were tested. The recovery of gold from sulfide gold-bearing concentrates by non-cyanide methods was 97- 99%, and from double refractory concentrates, 86-93%. The tested reagents are less toxic than cyanide, and their use will reduce of the cost of gold production. These methods make it possible to recover gold in acidic media, and eliminate the washing operation and POX slurry neutralisation. In addition, precious metals recovery from POX cakes using lead reduction smelting was investigated. It was shown that the “POX-pyrometallurgical” technology for double refractory concentrates processing could be used with recoveries of gold and silver of 97 and 96%, respectively. Keywords: Recovery of gold, refractory sulfide gold-bearing concentrates, double refractory concentrates, pressure oxidation, non-cyanide lixiviants of gold, chloride autoclave leaching, thiosulfate leaching, thiocyanate leaching, sulfite leaching, reduction smelting, POX-pyrometallurgical technology

Jan 1, 2020

By S. F. Böde, K. Böde

This paper focuses on developing a comprehensive and pragmatic information technology (IT) strategy for low-margin construction activities. This forms part of the realignment of the general business strategy, and refocusing the operational model. The main elements of the IT strategy formation are analysis of the current IT environment in terms of software and hardware, carrying out a gap analysis, and developing individual functional digitalisation strategies in construction execution based on Building Information Modelling (BIM), business administration processes, communication, business intelligence (BI) and reporting, and data security. Further, substantial emphasis is given to the sustainable strategy implementation in terms of hardware and software readjustments, their integration, user training, and defining the way forward.

Sep 1, 2021

By N. N. Malila, N. R. Shoko

The ever-increasing pressure on the profit margins of ferro-chrome producers and the gradual depletion of deposits of rich hard lumpy chrome ores calls for the ferrochrome industry to maximise the use of fine fractions of concentrates and friable chromite ores. Zimbabwe is endowed with huge deposits of refractory and friable ores that occur on and off the Great Dyke complex. The conventional metallurgical process of smelting of chromite ores in submerged arc furnaces is favoured by the use of refractory hard lumpy ores. The requirement to use all lumpy ore has been circumvented to a large extent at Zimbabwe Alloys. The use of briquetted chrome ore fines in the production of Ferrosilicon Chrome and High Carbon Ferrochrome has yielded positive results over a period in excess of twenty-five years. Of the three industrially used methods of agglomeration of chromite ores; sintering, pelletisation and briquetting, briquetting is preferred because the other two are associated with higher capital and operational cost. Zimbabwe Alloys has developed operational and technical expertise on the briquetting and utilisation of chromite ore fines and concentrates. Variations in the quality of available chromite ore fines imply that their amenability to briquetting is a dynamic problem. Appropriate briquetting parameters to guarantee quality briquettes are essential to the successful use of briquetted chromite ore fines. In developing a technology for briquetting of chromite ores, it is important not only to study the mineralogical and grain-size characteristics of the chromite ore fines but also to make an informed choice of the type and quantity of the binder and the conditions for producing a physically and chemically competent green and cured briquette. This paper discusses Zimbabwe Alloys' experience on the briquetting process and the advantages derived in the smelting of the briquetted chromite ore fines in comparison to the use of conventional lumpy chromite ore with respect to improvements in chromium recovery and as a consequence related efficiencies and unit cost of production.

Jan 1, 2004

By B. Larsen, S. Z. Nascimento, K. Fidje, J. P. M. Amaro, H. Gran

Safe and good operation of Søderberg electrodes is dependent upon high quality electrode paste coupled with correct electrode operating procedures. Good electrode performance depends further on proper melting and densification of the electrode paste. The melted paste should form a dense and viscous layer that prevents gasses from the baking process to move upwards. Both paste cylinders/blocks and briquettes can be used, but the procedures may differ between the various types of paste products. For briquette columns the formation of the important viscous layer is obtained through melting and densification of the briquettes. By basic rheological studies of electrode paste and by laboratory tests of briquette beds at isothermal conditions we have achieved a better understanding of the melting process. The effects of temperature gradients, pressure and friction between the briquettes and the electrode casing have also been evaluated qualitatively in pilot scale experiment and in industrial scale tests. The paper shows that melting and densification starts at a considerable lower temperature than the pitch softening temperature. It is concluded that the formation of a briquette electrode column depends on parameters as temperature, briquette column pressure and the friction. Operating conditions influencing the above parameters should be defined and established for each specific furnace operation. Such factors are e.g., charging and slipping procedures, column heating and electrical conditions.

Jan 1, 2004

By P. R. Segopolo

"The purpose of the project is to convert current shuttle car utilization on an underground coal mine to best practice by focusing on change-out points and tramming routes, which have a major influence on shuttle car away times. Time studies were an integral part of the project as these enabled the determination of shuttle car away times. An indirect proportional relationship between shuttle car away times and productivity is established. Through the time studies, it is deduced that a third shuttle car will make an insignificant contribution to production when there is only one split open. During this time, maintenance on the third car can be optimized. In order to satisfy the mine’s key performance indicator of keeping shuttle car away times less than 75 seconds, a belt extension must be scheduled after the third split is open. It is established that at any given time, a minimum of two shuttle cars should be used. When cutting on the left-hand-side of the belt road with only two shuttle cars available, the centre and left (left of the feeder breaker) shuttle cars should be used for coal hauling. When cutting on the right-hand-side, the centre and the right-hand-side cars should be used. If only one shuttle car is available, the centre car is the most efficient to use. Alternative anchoring configurations can be employed so as to enable cars (left or right, especially) to reach the opposite extremities of the panel and hence minimize cable length restrictions. Paper written on project work carried out in partial fulfilment of BSc. Eng. (MiningEngineering)"

Jan 1, 2015

By K. G. Matshika

"Nickel electroplating from sulphate electrolyte is an efficient process. To achieve good quality cathode, however, parameters such as temperature, nickel concentration, pH, electrode alignment, electrolyte flowrate and additives must be optimised, because these affect cathode morphology and current efficiency. It is also important to control the clarity and contamination of the electrolyte, as these have a considerable effect on the quality of the cathode surface. Delamination, surface roughness and pitting on the cathode surface can be caused by incorporation of solid particles or impurities form the electrolyte. Three types of solid particles were investigated: cuprous selenide, barium/ lead sulphate (co-precipitated) and ferric hydroxide. These particles can be found in industrial electrolytes, especially if there is a problem with the filtration step or contaminants have reacted to form insoluble particles. A rotating cylinder Hull cell was used for this investigation. It is found that the effects on morphology depend on the type of solid, concentration, particle size, current density and electrolyte flowrate. Cuprous selenide is the most detrimental, especially at higher concentrations, higher current densities and low flowrates. Increased rotational speed offers a uniform sheet of fine gas bubbles across the surface of the cathode which reduces the thickness of the diffusion layer of liquid adjacent to the cathode and increases the rate of mass transport to the cathode from the bulk liquid. INTRODUCTION Electrowinning operations are important when recovering associated by-products of nickel production, such as copper, cobalt and zinc, from pressure leach solutions. The base metal mineralization associated with platinum-group metal (PGM) production yields significant quantities of copper and nickel as by-products. The base metal refinery is vital in PGM processing as it increases the PGM concentration from mined ore by a factor of 400, in comparison with concentration by flotation (20 times) and pyrometallurgical processing (20 times) (Crundwell et al., 2011). Anglo American Platinum Ltd produces nickel cathodes by electrowinning and purges sodium from the base metal refinery in the form of sodium sulphate at the Rustenburg Base Metals Refinery (RBMR), as shown in Figure 1. This is the Sherritt acid leach process used in most base metal refineries to ensure no loss of PGMs and shows the subsequent purification steps for copper and nickel. Other refineries in Zimbabwe, such as Bindura and Empress, use the Outokumpu leach process (Pavlides, 2001)."

Jan 1, 2015

By A. J. S. Spearing, M. Sharifzadeh, K. V. Jessu

Empirical pillar design methods are commonly used in the mining industry. The parameters within which these methods are valid are frequently unknown to the user or ignored. In addition, empirical design may not consider essential parameters such as blasting effects, orebody dip and the presence of geological structures, which all adversely affect the stability of the pillars. This can result in potentially serious pillar design strength over-estimates. Although the commonly based tributary area method is generally conservative, as the spans are seldom that large relative to the depth, failing to consider other relevant parameters can result in errors. Problems associated with an under-designed pillar can range from a local pillar collapse to a catastrophic chain reaction collapse (or run). Over-designed pillars are generally safe but reduce the extraction of the orebody, thus adversely affecting the profitability of the mining operation. We used laboratory tests and numerical modelling to understand the effects of pillar orientation, blasting and the presence of discontinuities on pillar strength. Reduction factors were developed with these models to be implemented in conjunction with the existing empirical pillar design methods. For any pillar or mine design, once it is implemented, the actual performance of the system must be checked regularly by observation and monitoring and adjusted if needed. The pillar design approach outlined in this paper can better optimize the pillar mining method by considering other generally ignored but important parameters, thus improving safety, productivity, and economic aspects.

Oct 1, 2022

With the passing of Dr William Bleloch on 20th June 1991, we lost not only a colleague and a good friend but a man who made a very significant contribution to the industrial development of South Africa. He can rightly be called the father of the ekctrochemical and electro-metallurgical industries in this country, since his ideas and dedicated work were directly responsible for the development of these large industries as we know them today.

Jan 1, 1991

By S. Mundike

A scraper-based block cave method has been successfully applied to extract the Lower orebody at Nchanga since the 1950s. Since inception, scraper drifts and service ways have been supported using steel arch sets fabricated to a specific design from high strength manganese steel To reduce costs and to improve productivity, trials commenced in 2002 using fibre reinforced shotcrete as an alternative support method. One of the areas, the 2420 8E 1C trial drift, was subjected to abutment loading for several months prior to undercutting and cave mining. Shotcrete installed exhibited minor cracking shortly after application but very little deterioration thereafter. Following the success of the trial, the application of fibre-reinforced shotcrete was extended to other drifts. This paper describes the application of fibre-reinforced shotcreteat Nchanga and outlines design and quality assurance methods employed.

Jan 1, 2005

By M. Mostert

Mining companies sponsor a range of non-core, corporate social responsibility projects to adhere to social and labour plans and environmental management prerequisites that form part of a mining licence application. Some companies go above and beyond such projects, sponsoring initiatives that generate renewable energy through solar power, wind energy, natural gas, etc. The challenge for these companies is to choose between a variety of projects to ensure maximum value, especially in times when the economic climate might be less favourable for such projects. The focus of this research was to analyse the concept of sustainability as it exists today, and to apply that to the triple bottom line accounting method in an attempt to quantify the sustainability of a project. Research was done on the methane burn-off project at Sibanye Gold?s Beatrix Mine to establish how such projects are planned and financed, and what impact they have on the triple bottom line of a company. The financial bottom line is, by definition, one that executives understand. This paper also proposes a quantitative method for defining the social and environmental bottom lines as well. By considering the financial, social, and environmental values, the study attempts to determine a monetary value for a sustainable renewable energy project. This monetary value can be compared to similar values obtained for other sustainable renewable energy projects under consideration. The research suggests that monetary value alone is not enough to base a sustainable decision on, and qualitative measures are suggested for use in conjunction with quantitative methods. The selection method proposed should assist the board of a mining company to choose the most sustainable option and the project that will add the greatest value to the company across all three bottom lines. It will also provide increased justification for such renewable energy projects, even in periods of harsh or uncertain economic climates.

Jan 1, 2014

By J. Kirsch

Keywords: Pyrometallurgy, pneumatic transport, pneumatic transport Dense-phase pneumatic injection has begun to replace more traditional furnace-feeding systems. The paper describes the technology as it is applied to processes where the back pressure at the point of injection is greater than 50 kPaG. It reviews earlier systems of injection and more recent developments that address concerns for instantaneous control in modern smelters. The new technologies fall into two groups, (1) modified pressure-difference control (sub-divided into simple and complex) and (2) mechanical-feeder-based control. Features of current injection systems include feed splitting in two forms, passive and active, and co-current injection.

Jan 1, 2006

The excavation of ramps and tunnels often requires high-speed development with (or without) the use of high-energy mining equipment such as loaders, dump trucks, TBMs and roadheaders. This high-speed development creates a challenge in terms of providing a safe and productive working environment. For example, heat from continuously exposed surrounding rock, heat from broken rock, heat generated by mining equipment, potential in flows of hot ground water, pollution from associated diesel equipment and the distance of the advancing face from fresh through-ventilation all have to be taken into account when designing ventilation systems for high-speed ramp and tunnel developments. This paper discusses methods of achieving acceptable environments at the face and along the length of the tunnel. The methodology has been successfully implemented in the development of long (up to 20 km) TBM drives in the Lesotho Highlands Project and in mining projects in hot rock using drill and blast methods as well as mechanized methods using continuous miners and roadheaders. The determination of heat loads includes calculation of the heat flow within the surrounding rock, evaluation of the operating cycle of the equipment and the contribution to the overall heat load of the broken rock as it travels out of the tunnel. The determination of heat loads from surrounding rock in new tunnels required a modification of the algorithms generally used for established excavations. The paper also examines the use of, for example, mobile duct and fan systems to ensure that fresh air is delivered to the specific areas where workers are located.

Jan 1, 2000

By M. S. P. Rampedi

The paper reports on a vacation work project conducted at Khuseleka No. 1 Shaft, Anglo Platinum, where there was a need to optimize the transport of personnel to level 15 and below. Approximately 900 men per hour need to travel between the shaft and the start of the current chairlift system. Time studies were used as the major indicator of the extent of the current problem, and it is recommended that a new chairlift system be installed to cover the distance from the vertical shaft station at level 15 to the chairlift decline station on level 15. A capital cost of approximately R10 million is necessary to carry out the proposed recommendation. Khuseleka No. 1 Shaft has the capacity to wind 1070 people per hour, and the current labour complement going to the level 15 shaft station stands at 1570 employees; thus at optimum efficiency the proposed chairlift system could transport the entire shift to the start of the current chairlift system in only 1 hour and 45 minutes. Reducing the distance walked at the start of the shift may also have an impact on productivity.

Jan 1, 2012

By D. Tsweleng

In the Evraz Highveld production process, iron ore is prereduced in rotary kilns prior to charging into submerged arc furnaces (SAFs). Owing to the highly aggressive slags that are formed within the combustion zones of these kilns, chrome-oxide-containing lowcement castables have been used for some years in the kiln lining. Due to concerns around the potentially harmful effects should Cr(V1) be present in the spent linings, Highveld and its suppliers of kiln castables devoted time to developing alternative chrome-free lining materials. Such materials needed to be cost-effective and ensure good performance and improved kiln availability. This paper discusses all the parameters surrounding this development. Keywords Low-cement castable, chrome-oxide free, chrome (VI), titaniferous magnetite ore, rotary kiln, submerged arc furnace, open slag bath furnace, Evraz Highveld Steel & Vanadium Limited.

Aug 1, 2013

By Ernie Holden, Chris Ringas

In the last 20 years, In Line Inspection (ILI) using intelligent pigs has become the principal tool used by pipeline operators to assess the condition of their pipelines. New pipelines are normally designed to take intelligent pigs, but many older pipelines require some modifications and special procedures for their inspection. This paper is aimed at practicing engineers and managers of pipelines, or people aspiring to those positions. The paper describes the benefits of ILI and some of the practical issues regarding pipeline preparation and cleaning, choice of inspection tool, running pigs in pipelines, and what to do with the data collected. What are the responsibilities of the Pipeline Engineer ? ? Maintain reliable and acceptable performance of the pipeline in terms of safety and product delivery at economical cost. ? Provide a defined margin of safety for operating the pipeline at its designated pressure. ? Provide timely information on all pipeline defects such that repairs can be carried out according to a managed schedule. What Defects does the Pipeline Operator have to cope with ? A useful record of actual incidents seen in pipelines can be obtained from the web site of the US Office of Pipeline Safety (OPS) - http://ops.dot.gov/stats/stats.htm. US pipeline Operators are obliged by Law to report all pipeline incidents exceeding certain threshold criteria (e.g loss of life, escape of product, cost of incident etc). These OPS statistics show that corrosion and third party damage have remained consistently the prime causes of reportable incidents in the US, with similar experience elsewhere. There are several kinds of flaws and defects in pipelines that can lead to failure, the main families being :- ? Metal loss ? Cracks or crack-like defects ? Laminations and other mid-wall defects ? Geometric anomalies

Jan 1, 2006

By M. Abdellatif

Keywords: Magnesium, pyrometallurgy, Mintek Samples of crude magnesium produced by the Mintek Thermal Magnesium Process were refined in two stages. The first stage consisted of co-melting of batches of the crude metal and MgCl2-KCl flux (cleaning), followed by stirring at 30 rpm for 30 minutes and settling of the sludge (mixture of molten salt and solid impurities) from the magnesium melt. The operating temperature was 680?730°C. Most of the contained calcium and significant proportions of iron and silicon were transferred into the sludge phase, which left a metal containing, on average, 950 ppm Si, 470 ppm Fe, and 230 ppm Ca. In the second stage, small-scale refining tests were conducted on cleaned samples from the first stage, as well as on crude magnesium. FeCl3 was used as the refining agent. These tests were carried out at 715?760°C with various amounts of the refining agent. The refined metal was suitable for the production of various magnesium alloys, particularly AZ91D.

Jan 1, 2006