Search Documents

By Robert M. Doerr

Isothermal oxidation kinetics were determined for three grades of Ni and for 99.99 percent Co in Ca and in air from 800° to 1,200° C. The oxidation reactions followed approximately the parabolic rate law. For 99.99 percent Ni in 02 at 1,200° C, the parabolic rate constant was 2 mg cm-2 hr-2. For 99.99 percent Co in dry air, the constant ranged from 1 mg cm-2 hr-2 at 800° C to 18 mg cm-2 hr-2 at 1,200° C; for 99.99 percent Co in 02 the constant was 2 mg cm -2 hr-2 at 800° C and 10 mg cm-2 hr-2 at 1,000° C. For 99 percent Ni in dry air, the constant ranged from 0.2 mg cm 2 hr-2 at 800° C to 3 mg cm 2 hr-2 at 1,200° C. By X-ray diffraction measurements, only divalent oxides were found in the scales. Volumetric and quartz-helix gravimetric methods were used. The volumetric apparatus was designed to permit less stringent restrictions on the corrosion specimens; it was also more convenient to use. The agreement between the weight gain determined gravimetrically and the 02 consumption determined volumetrically was not good enough for direct comparison of gravimetric and volumetric results.

Jan 1, 1963

By Bernard Porter

The densities of LiF, NaF, and KF, of binary mixtures of these alkali fluorides, and of binary mixtures of UF4, ThF4, YF3, LaF3, and CeF with each of tie alkali fluorides were measured as functions of the melt composition and temperature. Molar volumes at 1,000° C were calculated for all the mixtures. Binary systems containing LiF exhibited molar volume ideality. Binary fluoride systems containing either NaF or KF as the alkali fluoride exhibit positive deviations from molar volume additivity. However, molar volumes in the NaF-KF system are ideal.

Jan 1, 1966

By Reed. Donald F.

"Deposits of gray hematite occur in two districts in Talladega County, Ala., the Emauhee-Tallasochatchee and Weewoka, both in the vicinity of Winterboro, 50 miles east of Birmingham.The deposits were investigated by the Bureau of Mines in 1943 and 1944. Approximately 13,000 feet of diamond drilling was done and 6,000 linear feet of trenches excavated and sampled.A total of 13,000,000 tons of ore averaging 36 percent iron was indicated in all areas.A detailed discussion of each property investigated, drill logs, and sampling results are given in this report.In the work done in the Talladega County iron investigation, special acknowledgement is due to Paul M. Tyler, formerly regional engineer, Eastern Region, and Richard W. Smith, formerly district engineer, for aid and direction of the project; also to J. B. Clemmor, metallurgist, for diligent research work in the Southern Experiment station laboratory. All were members of the Bureau of Mines Staff.The project was conducted in cooperation with the Federal Geological Survey, whose field work was in charge of T.G. Andrews assisted by Brewster Baldwin. The able and valuable assistance of Andrews and Baldwin aided greatly in accomplishing the project.The areas investigated by the Bureau of Mines were in two districts: The Emauhee-Tallaseehatchee district, between Sylacauga and Sycamoer (marked B on fig. 1) and the Weeworka district, between Winterboro and Sycamore (marked A on fig. 1)."

Mar 1, 1949

By Charles H. Simmons

Two versions of a VF transceiver to aid in location of trapped miners has been developed and tested. The belt worn model was produced in both transmitter and transceiver configurations. In addition, a quantity of the belt worn models were fabricated using aluminum wire instead of copper in order to reduce unit weight. Ten prototypes of a battery cap model VF transceiver were also fabricated demonstrating further unit size and weight reduction while maintaining electrical performance. Samples of- both versions were tested environmentally and the test data is included in this report. While both versions of the VF transceiver are similar electrically, and are constructed using convential manufacturing techniques, the battery cap model realizes a lower total weight, smaller volume and production cost than the belt worn version. Operationally, the battery cap model assures that the VF transceiver will always be with the miner.

Jan 1, 1981

By C. L. Klingman

The Bureau of Mines tested eight commercially available, activated charcoals experimentally to compare the following characteristics: capacity for adsorption of nitrogen at 77° K and 170 atmospheres' pressure, surface area, carbon tetrachloride adsorption capacity, hardness, and density. The nitrogen adsorption test was devised to simulate plant conditions occurring in the final step of purification in Bureau helium faciliti.es. The remaining tests were patterned after empirical acceptance tests that are widely used throughout the adsorbent industry. Surface area and carbon tetrachloride adsorption correlated well with nitrogen adsorption. The samples with low density generally had better adsorption qualities than those of higher density. The carbon tetrachloride test appeared to be the most practical for selecting a charcoal to be purchased, but an attrition, or hardness test should also be run to be sure the charcoal will not crumble in use.

Jan 1, 1966

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

By Hon-Yim Ko

1972 constituted the second year of the projected five-year study on constitutive relations of coal. The schedule adhered closely to the five-year outline which is summarized in Table 1. This chapter is intended to serve as introduction and concise synopsis of the year's activities and results, which are presented in greater detail in the following chapters, which have been contributed by the individual researchers in charge of the various aspects of the project under study. Coal Sources, Material Procurement, and Sample Preparation Most of the studies performed during 1972 were done on coal from two sources: the Old Ben Mine #22 in Illinois, and the Bruceton Mine in the Pittsburgh seam of Pennsylvania, which may be considered typical of coal sources of economic importance in the Midwestern and Eastern part of the U.S. These two mines have proven to be reliable suppliers of coal material for our research. We have been able to establish good working relations with their personnel and feel that we can continue to count on their cooperation and help.

Jan 1, 1972

By Reinhardt Thiessen

This paper presents only the highlights of previous research on the paleobotany of coal. The accumulated material has become so vast that a comprehensive review of all findings relating to paleobotany would be far too long. The fact that coal is derived from plants is now so well-known that no further comment is required, but knowledge of the mode of transformation of plant substances into coal is not so general. The plant matter goes first through processes of semirottins-, maceration, and elimination of certain material to form peat, which is then further transformed into coal. The first stage has been termed the "biochemical process," because the more important changes take place under the influence of micro-organisms. Near the end of the biochemical action an unconsolidated peat is formed. The second or "dynamochemical process," caused by the addition of superincumbent rock strata such as sandstones and shales and application of additional pressure and possibly heat through mountain-building forces, results in the formation of higher-rank coals ranging from brown coal to anthracite. These stages in trans-formation of plant material to coal have been described in previous reports.4 The main object of this paper is to bring to the notice of paleobotanists the fact that coal contains an enormous amount of material in a remarkably good state of preservation. Although some of the coal-forming matter has lost its identity, much of the original structure is retained. A large proportion of the coal, therefore, particularly of common bright coals, comprises constituents or components that invariably have retained some of the original plant structure, and many of these structures may be assigned to certain plants. The identity of these plants and of the remains forms the subject of this paper.

Jan 1, 1941

By L. A. Haas

In this Bureau of Mines investigation, conditions were determined to form an iron sulfide adherent coating with a metallic golden luster on steel upon anaerobic heat treatment with sulfur. The sulfide formation rate was determined in the temperature range of 105° to 500° C with reaction times up to 68 hours. The optimum temperature and time to form an adhering decorative coating on mild steel was in the range of 105° C for about 70 hours to 285° C for 1 hour. The golden coating consisted of an inner layer of pyrrhotite and an outer layer of pyrite. At temperatures higher than about 300° C, the outer layer thickness decreased owing to the decomposition of pyrite to pyrrhotite.. Small quantities (<0.5 wt-pct) of petroleum oil accelerated the sulfide growth rate. The sulfide coating decreased the corrosion rate of steel in a neutral aqueous medium by a factor of two. The dissolution of pyrite in water was dependent on particle size and surface area with the flat pyrite coatings exhibiting the lowest dissolution rate.

Jan 1, 1974

By Christopher C. Jobes

This U.S. Bureau of Mines report describes a system to determine the position and heading of a mining machine during maneuvers in the face area of an operating mine section. The system is the first step in the development of a guidance system for automated mining machines. The position and heading algorithm is described, and a preliminary error analysis is performed. The sensors employed were linear position transducers mounted on a mining machine with their cables attached to points on a stationary reference. Four linear position transducers were used to provide a data redundancy that increased the reliability of the guidance system. The linear position information obtained from the transducers was processed mathematically via the position and heading algorithm to provide the desired position and heading information. The algorithm takes advantage of sensor redundancy to continually test the accuracy of the sensor data. The major sources of error were determined to be the linear position transducers, the analog-to-digital (A/D) converter used to interpret the data, and the sampling frequency of the measurement system. These sources of error were evaluated to determine their inaccuracies for use in calculating the overall system accuracy.

Jan 1, 1990

This report summarizes the cost of U.S, mining and milling industry compliance with the Environmental Protection Agency (EPA) interim water quality guidelines for waste discharges. Applicable excerpts from Public Law 92-500 are stated and interpreted in conjunction with the guidelines being used for implementation of the law. Over 200 U.S. Army Corps of Engineers applications for discharge permits were used to develop the quality and quantity data base needed to estimate the cost to comply with EPA guidelines, Cost of three basic treatment methods were considered: Aeration, addition of lime, and sedimentation. From the process design, cost-capacity graphs were developed to consider maximum flow rate, maxi lime addition, and average flow rates. The graphical method used in this evaluation should provide a reasonable guide to the effect of waste treatment and, therefore, Public Law 92-500 and corresponding EPA guidelines on the mineral processing industry. The cost of complying with the EPA guidelines will have the effect of prompting the mining industry to minimize the production of waste water and of undertaking some additional treatment, Two case studies are presented to illustrate efforts that might be fruitful for minimizing waste water production and for treatment of combinations of acid mine drainage, mill wastes, and metallurgical process wastes when treatment is deemed necessary.

Jan 1, 1975

By I. Liebman

A Bureau of Mines study is in progress to determine the effectiveness of passive water barriers in suppressing coal-dust explosions. A 2.9-ft3-capacity water-filled plastic tub was found effective in suppressing dust explosions propagating at speeds of 250 to over 1,000 ft/sec. Work directed at determining the limitations of water barriers showed that the passive water barrier technique is also feasible for the suppression of weak dust explosions propagating at speeds of 100 to 250 ft/sec. For relatively slow accelerating flames, dynamic wind forces appear to be the important quantity governing fragmentation of the plastic tub and subsequent water release and dispersion, whereas dynamic impulse appears to be the significant quantity for rapidly accelerating flames. The acoustic approximation (relation between static pressure and flame or wind speed) is shown to be valid in a long single mine entry. This relationship appears to be useful in predicting the regions within a long single entry where passive water barriers are effective in quenching a dust explosion.

Jan 1, 1974

By Craig C. Hustwit

A pilot-scale treatment study was conducted on a copper-zinc bearing metal mine drainage using a pipeline treatment system called the In-Line System (ILS). The objective of this U.S. Bureau of Mines study was to determine whether the ILS could be extended from the treatment of coal mine drainages to the treatment of metal mine drainages. Hydrated lime (Ca(OH)2), quick lime (CaO), and caustic soda (NaOH) were used to neutralize the drainage. A novel reagent slurry of Ca(OH)2 and type C fly ash was also evaluated. Except for Ca(OH)2-fly ash slurry, treatment performance was evaluated for all reagents at pH values of 7,8,9, and 10. The Ca(OH)2-fly ash slurry was evaluated at a pH of 10. All reagents tested neutralized the metal mine drainage and substantially reduced the dissolved metal concentrations. It was concluded that the ILS could be useful in the treatment of metal mine drainages.

Jan 1, 2010

By William L. Crentz

This Investigation of the preparation characteristics of the coals in Armstrong County, Pa., is the third in a series of Bureau publications by counties appraising the practicability of upgrading marginal deposits to metallurgical standards. Earlier investigations covered the washing characteristics of the coals occurring in Cambria County, and the principal reserves remaining in Indiana County. In Armstrong County, the Upper Freeport bed is the major source of production, the Lower Kittanning bed being of secondary importance. The Lower Freeport bed is mined to some degree, but it is usually too thin and spotty in occurrence to support large-scale operations. The remaining production is taken from the Pittsburgh, Middle Kittanning, and Upper Kittanning beds, but the quantities are insignificant. Table 1 shows the county&apos;s coal production) by beds, during 1948. The coals of Armstrong County are not generally considered to be of metallurgical quality because of the high sulfur content. The raw coals usually analyze more than 2 percent sulfur, and more than 4 percent sulfur is not uncommon, especially in the Lower Kittanning bed.

Jan 1, 1951

By Jr. Koch

Statistical methods applied at the Bureau of Mines Denver Mining Research Center to data from metallic ore bodies were used to evaluate lignite reserves from core data and to predict the extent of lignite horizons in some Texas lignite beds. Six lignite seam units were studied using data from 361 drill holes. The data indicate a total of 214.2 million tons of lignite in the area examined, and probable reserves of 113 million tons in an area 2,000 feet beyond the limits established by the drill holes. It was demonstrated that lignite reserves present in lenticular beds could be reliably determined by statistical techniques, and that core drilling could be optimized to maximum information with minimum drill holes. The technique described is applicable to other coal beds.

Jan 1, 1966

By L. R. Herrmann

The most fundamental feature of fracture is that it involves separation. Such separation can arise by either separation of molecules, more or less along the line joining their centers (tension), or by d sliding separation roughly perpendicular to that line (shear). Theoretically, a perfect crystal could never be broken by the application of perfectly axial compressive stress (until some sub-molecular actions occur). In tension fields the calculated forces between molecules are extremely high. Consequently, calculations based on the forces known to exist in materials at the molecular and crystalline levels always lead to strengths which are two or three magnitudes higher than the strengths obtained in service or in the laboratory. It has been a major problem, therefore, to explain: (a) How fracture can occur in compressive stress states. (b) Why the observed strength of a material is always much lower than its calculated strength.

Jan 1, 2012

By Terry R. Neumann

During 1983, U.S. Bureau of Mines personnel examined mines, prospects, and mineralized zones to evaluate the mineral resources and potential of the Funeral Mountains Wilderness Study Area (WSA), Inyo County, California. Eleven mineral properties and two mineralized zones were examined during this study. Of these, six are within the study area and seven adjacent. There are no active mines, in the WSA, nor is there evidence of past production from any claim within the study area. The WSA contains no identified mineral resources. However, occurrences of bentonite, zeolites, and strontium were found in the area. There is little likelihood for resource development of any occurrence in the WSA. The area, in the Basin and Range Physiographic Province, is dominated by a Paleozoic marine sequence. Segments of Tertiary continental fluviolacustrine sediments, including volcaniclastic rocks, abut and overlie the Paleozoic rocks in fault controlled basin areas. Significant concentrations of bentonitic clay and zeolites occur as alteration products in Tertiary tuffaceous sedimentary rocks. However, they are generally low-grade, thin, and discontinuous, precluding commercial development. Limestone, quartzite, and sand and gravel in the area are suitable for many types of construction uses, but similar deposits outside the WSA are closer to markets. No energy resources have been identified in the WSA.

Jan 1, 1984

By Shirley F. Colby

Much interest has been shown recently in the possible utilization of dolomite as a source of magnesium metal, a large production of which is deemed essential for national defense. As a result, many inquiries have been received by the Bureau of Mines as to sources of dolomite. This report has been prepared primarily to augment the Bureau&apos;s present published information on the occurrence of high-grade dolomite deposits in the United States. To supplement such data, the report also defines dolomite and related rocks and describes their properties and uses. The uses are covered in some detail in Information Circular 6524 entitled "Utilization of Dolomite and High-Magnesium Limestone," published in 1931 but now out of print. All essential data on uses contained in that report have been incorporated herein, and. have: been supplemented by data developed during subsequent years. DEFINITION Dolomite is a mineral composed of calcium end magnesium carbonates combined in equal molecular proportions, expressed by the formula CaMg(C03)2. Dolomitic limestones contain considerable dolomite but also include either

Jan 1, 1941

By M. M. Fine

"Button" type ore from the Cason mine, Batesville, Ark., can be up-graded to plus-40-percent manganese by mineral-dressing procedures. A simple process including gravity concentration and. magnetic separation yielded more than 50-percent recovery of concentrates containing 38.1 to 40.6 percent manganese. These values in turn could be raised to 41.4 and 42.8 percent, respectively, upon sintering to conform to size specifications. The Bureau of Mines in the past has surveyed and tested many manganese ores and prospects in an endeavor to alleviate the shortage of manganese. The present period of emergency again emphasizes the strategic position of the metal, and manganese investigative work is being stressed to find new ore bodies and to apply newer beneficiation techniques to the known deposits.

Jan 1, 1953

By Forrest T. Moyer

INJURY experience and related employment information are presented in the chapter for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1964. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. All rates in the text are calculated separately on data before rounding, hence component rates may not add to the total rates shown in the tables. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III. COAL Injury experience of the coal mining industry was improved in 1964, as measured by the declines of 1 and 14 percent, respectively, in the frequency and severity rates. Although the total number of injuries increased in 1964, a slightly greater proportional increase in man-hours worked caused the frequency rate to drop to 44.65 per million man-hours. The injury-severity rate in 1964 was 7,832 days lost per million man-hours of exposure. Employment and injury data for 1964 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines. Fatality experience improved significantly with a record low number of 240 deaths in 1964. This total was 44 less than in 1963. The Nation&apos;s coal mines during 1964 were free of major disasters (a single accident resulting in the death of five men or more) for the first time since 1956. The

Jan 1, 1965