Search Documents

By F. D. DeVaney

The low-grade deposits of manganese ores along the Missouri River near Chamberlain, S. Dak., are known to contain one of the largest reserves of manganese in the United States. Manganese occurs as concretionary nodules ranging in size from 13 inches in their longest dimension to particles finer than 65-mesh. The nodules are embedded in soft, wet shale, which contains little manganese. The removal of nodules from the low-grade shale is a simple mechanical problem; the question is primarily to determine the lowest-cost method of separation. This report purposes to present data acquired by experimenting with samples of the ore, which form a basis for suggesting methods of concentrating manganese nodules.

Jan 1, 1942

By V. F. Parry

The major industrial uses of char or semicoke produced by low-temperature carbonization of coal4/ are as fuel for generating electric power, for blending with metallurgical coking coal as a substitute for low-volatile coals, and for gasification to produce synthesis gas for chemical purposes. This paper discusses various methods for carbonizing coal, emphasizing processing of the noncoking coals to produce char for thermal power-plant fuel and for blending with metallurgical coking coals and tar for chemical use. Low-temperature carbonization is a relatively simple processing step involving heating coal to about 900° to 1,200° F. to decompose the coal into 4 main products: (1) Semicoke or char; (2) complex, partly oxygenated liquid hydrocarbons or tar; (3) fixed gases; and (4) water. If the coal is heated rapidly under conditions that prevent decomposition of the primary products, 68 to 87 percent of the net heat in the raw coal is left in the char and 10 to 23 percent of the potential heat appears in the primary tar. Fixed gases represent approximately 7 percent of the heat and approximately 2 percent is lost or dissipated in the reactions of decomposition. Considering the different ranks of coal in the United States, the yield of tar will vary from about 9 to 44 gallons per ton, therefore it is important that each coal be carefully considered if it is to be carbonized for industrial use.

Jan 1, 1955

By Edwin S. Secor

The Federal Bureau of Mines conducted a field survey of 153 bituminous coal strip and auger mines to estimate coal recovery from surface mines in the Eastern United States. Recovery was calculated from field data by measuring coal losses resulting from mining coal and leaving barriers. Mean total recovery for strip mining in States east of the Mississippi River was 83.0 percent and ranged from 72.3 percent for Tennessee to 91.3 percent for Maryland. Mining losses and barrier losses were 10.1 and 7.7 percent, with standard deviations of 4.8 and 10.4 percent, respectively, indicating that barrier losses, although less than mining losses, were more variable. Mean total coal recovery varied only slightly for the two regions studied; 82.7 percent for Appalachia and 84.3 for the Midwest. Total recovery grouped by mining method--contour, area, and mountaintop removal--was 79.8,84.7, and 85.3 percent, respectively. Mean auger recovery was 35.9 percent; of the total average loss of 64.1 percent, over one-half resulted from design limitations while the remainder was attributed to operating losses. The wide recovery range at individual mines indicates the variability of the eastern surface coal mining industry. Because of this, care should be exercised in applying the results of this report to reserve estimates other than those of a general nature.

Jan 1, 1977

The following pages discuss the objectives, the background, and scope of work of an industrial engineering analysis of far-,n haulage systems in underground retreat coal mining. This study ran concurrently with an existing industrial engineering study of methods of improving safety and production efficiency in underground pillar extraction. 1. OBJECTIVES The objective of this project was to provide basic data inputs that will inpart knowledge as to the major constraint to pillar extraction sections. Furthermore, the industrial engineering study will suggest ways to optimize haulage systems and to develop more efficient work practices and operational techniques that will maximize equipment utilization.

Jan 1, 1975

By Richard N. Spencer

This report describes investigations of the economic merits of multiple zone mining and beneficiation versus selective mining of altered Western phosphate rock. The same deposit was considered in both instances and it was assumed that the grade of selectively mined ore was comparable to the grade of the concentrate from beneficiation. The beneficiating scheme used for the investigation was one proved by small continuous circuit operation. All economic factors were found to favor multiple zone mining plus beneficiation. Capital requirements and production costs were lower, and production life of the deposit was extended 4.5 times. The concentrate from beneficiation would be a uniform high-quality feed for acidulation and would be low in stable metallic oxide (R203) content. Such a feed would permit improved plant operating control, and the low R203 would promote more rapid filtration and minimize sludge formation in the phosphoric acid. With the proposed treatment, the concentrate produced by flotation from this deposit would cost about 1.5 times as much per ton as the concentrate produced by classification sizing. Therefore, inclusion of a flotation step in treatment schemes requires an economic analysis for each ore deposit.

Jan 1, 1971

By John W. Mentz

Phase I study efforts addressed: 1) acid mine drainage formation theory; 2) effects of inundation in reducing acid mine drainage formation; 3) summary information on the types of acid abatement technology currently available and the problems inherent in each; 4) analysis of two potential means of partially inundating abandoned segments of active underground mines to reduce acid formation. This subsequent Phase II Draft Final Report addresses all of the above, but concentrates on and defines Item 4. Seal construction techniques were taken through five logical steps as follows: A) Location Analysis; B) Coal Barrier Pillar Analysis: C) Ground Water Analysis; D) Design Considerations: E) Economic Analysis. The design details of both low wall dams and section seals were discussed in a series of segments: a) Case Histories; b) Feasibility Analysis; and c) Design (including representative calculations). Study efforts showed that both concepts are feasible only in certain mines where the geologic-hydrologic physical makeup is suitable to contain a mine pool. Low wall dams in particular were found to have extremely limited applicability as a means of pollution reduction. Section seals, while clearly dependent upon site specific conditions, have a some what broader range of utility and are more effective in pollution reduction. The proven dramatic reduction in acid mine drainage attributable to inundation makes this a concept that must be considered.

Jan 1, 1981

By L. J. Prosser

The Bureau of Mines has completed an underground degasification project in which an underground piping system was used to transport methane from the coalbed to the surface. In a la-month period four horizontal holes were drilled to an average depth of 1,450 feet. All four holes were surveyed vertically and azimuthally. In 991 days of degasification, 255 MMcf of gas was drained from the coalbed. The underground piping system proved to be a safe and effective means of transporting methane from the coalbed to the surface.

Jan 1, 1981

By L. H. ADAMS, C. N. HASKINS, J. K. CLEMENT

In the course of its investigations of the fuel resources in the United States and of the methods by which these resources could be utilized with greatest efficiency, the United States Geological Survey tested a great variety of coals and lignites as gas-producer fuel. Early in these testa it was found that many factors controlling the formation of gas in the generating chamber of the producer and, consequently, having a direct bearing on the management of producer-gas plants, were not as well understood as they should be. The Geological Survey therefore took up a detailed investigation of the chemical and physical processes that take place in the producer, keeping in view not only the possibility of increasing the efficiency of the producer as a source of energy, and the ensuing benefits to the public of cheaper power and greater utilization of low-grade fuels, but also the application of the results to the problems of boiler-furnace operations. - The Bureau of Mines, to which the testing and analyzing of fuels as carried on by the United States Geological Survey has been transferred, is continuing producer-gas investigations at the testing station at Pittsburg, Pa. Results of the gas-producer tests a made at the coal-testing plant erected at St. Louis, Mo., and of a study of some of the problems° that came up in the tests have been published by the Geological Survey. Results of the tests made at Norfolk, Va., and Pittsburg, Pa., and of further studies of particular problems, will be published by the Bureau of Mines. In the gas producer solid fuel is transformed into more readily combustible gaseous fuel. The transformation is relatively slow and consists of several processes: 1. The distillation of the volatile hydrocarbons from the freshly fired fuel at relatively low temperatures. 2. The combustion of the fuel by its combining with the oxygen of the air forming carbon dioxide (COO. 3. The formation of carbon monoxide (CO) and hydrogen (11 3), the essential constituents of producer gas, in accordance with the equations:

Jan 1, 1911

This report summarizes the results of the Narragansett Win Projec't's activities during the U.S. Bureau of Mines (BOM) Phase 1, which was transitional from and which followed the National Science Foundation (NSF) Phase which initiated the investigation of New England's potential roil resource. The 960 sq. mile basin is structural and topographic lowland containing 12,000 to 20,000 ft. of terrigenous clastic sediments of late Pennsylvanian age, and which rests on an upper Precambrian and Cambrian basement. The Rhode Island Formation, which is the coal-bearing unit, comprising the bulk of the Pennsylvanian rocks consists, in order of decreasing abundance, of sandstone, conglomerate, silts tone, shale, and coal. In the NSF Phase, 24 drill-holes yielded 17,900 ft, of core; in the BOM Phase I study, 4 drillholes yielded 2,100 ft. of core. Anthracite and semi-anthracite was encountered in beds Up to 30 ft. thick in widely spaced parts of the Basin. The coal, typically very low in sulfur, and a high ash anthracite, won mined in substantial volumes from 1808 to 1959 from shaft and open lit in Portsmouth and Cranston, R.I., and in lesser volumes in Mansfield, Mass. Currently coal is now being mined in Plainville, Mass. as a fuel in the manufacturing of light-weight aggregate from the same quarry that serves as the source of the rock being processed. The structurally complex Narragansett Basin is now known to have a greater extent than earlier since recent drilling by others (Chapter 2) has confirmed our interpretation that the Basin extended offshore south A Boston. The, Basin also extends into Rhode Island Sound to the south. The geological structure is more complex in the southern part of the Basin than in the northern part. Three episodes of folding have been documented on Aquidneck Island and four episodes of faulting have been demonstrated for the Basin as a whole. Relatively less well exposed rock in the northern part of the Basin, increases the difficulty of recognizing and correlating structural episodes in the northern part of the Basin. The Basin his hewn subdivided into six structural domains which appear to have distinctive structural, metamorphic, paleontological and sedimentological differences that mw assist in isolating important events in the evolution of the Basin and its component parts. The tentative structural model recently developed in POP Phase I has important implications for exploration and mining. In the first and second folding stages the coal is mobilized and thickened in the crests and troughs of folds whose axes are horizontal to subhorizontal. While conventional coal exploration and mining methods are not applicable, great thickening in the crests and troughs of large scale structures, which can he defined by geology, geophysics and drilling, may provide compensating advantages. Bedrock over most of the Basin is 0-50 ft., but thicknesses of glacial deposits up to 150 ft. are present locally. Pro-Pleistocene topographic trends are controlled by structure and rock hardness; Pleistocene deposits aligned to the S. F. are superimposed on earlier trends. The southern part of the Basin is mainly dominated by high grade Barrovian metamorphism and plutonism of Permian age, related to the Alleghanian Orogeny. About 300 sq. miles of the 960 sq. mile Basin has been affected. The remaining 660 sq. miles, in the chlorite and subchlorite zones of metamorphism are compatible with the presence of high quality anthracite and semi-anthracite. Illite crystallinity studies begun in the NSF Phase, have been carried out in the BOM Phase l with important results. About ME of the northern Basin is now known to be in the diagenetic (unmetamorphosed) or subchlorite zone and the remainder in the chlorite zone of metamorphism. Mite studies, probably best recording temperature effects, show a generally progressive increase from the NW corner of the Basin near Plainville, Mass. toward the south and southeast. Reflectivity and coal petrography studies, probably best recording pressure and effects related to shearing, indicate a generally opposite pattern. Thus these methods provide powerful tools for the ultimate solution of problems important to coal exploration for coals of higher combustible volatile content and exploitation of these. Due to the complex nature of the coal, chemical data may not he easily used to determine rank. The coals have been tectonically deformed and mineralized. This deformation plus thermal metamorphism have altered the coals, in some cases by producing natural coke. Brecciated coal is often coated with a secondary depositional carbon. The coals' hydroscopic nature and high ash contents are due to the deformed nature of the coal and the presence of this secondary carbon. The stratigraphy and sedimentology of the coal-bearing Rhode Island Formation is similar to described alluvial fan deposits. The non-geological studies al-low three conclusions to be made: 1. A substantial number of areas have been identified in the Narragansett Basin in which mining could be carried out without undue difficulty from a land use point of view. 2. Substantially more than two hundred instances of past or current- mining activities have been identified in the Basin. Many of those are in areas defined as geologically interesting, and may be advantageous From the point of view of future exploration. 3. The map synthesis technique developed for this contract is successful and may easily be adapted to future exploration in its current form and also in its expandable form dealing with unit measurements of one-tenth mile. We recommend that BOM Phase 2 exploration should accomplish the intent of the Congressional language in House Report No. 95-1251, to continue a substantial drilling and geophysics program: "The Committee expects the Bureau to continue studies involved in ascertaining the extent and quality of low sulfur coal reserves in the Narragansett Basin in New England including necessary drilling and geophysical studies. The knowledge of the extent of such deposits is of great importance to this 'energy pour' area".

Jan 1, 1979

By Robert M. Doerr

The research objective was to determine the effect of vanadium alloy additions on the oxidation behavior of cobalt-nickel Alloys. Eighteen alloys were reacted with 0 2 at 0.5 arm and 1,351°, 1,389°, and 1,429° K. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with V additions of 0, 0.9, and 2.7 wt pct. Large early deviations from, or changes in, the parabolic rate constant were encountered, but the reaction rate in most cases declined approximately in accordance with the parabolic rate law. Relatively, the vanadium degraded the oxidation resistance most at the highest nickel contents. In some cases, melting of the oxide was inferred from microscopic evidence and X-ray diffraction measurements disclosed the presence of low-melting vanadates.

Jan 1, 1970

By R. W. Stahl

Burning coal-mine refuse banks were surveyed in 15 States. The following characteristics were tabulated for 495 hanks: County; name, population, and distance of nearest town; size and status of bank; status and stage of fire; and topography. Ways of controlling fires were reviewed, the compacting and sealing method proving most satisfactory. Means for preventing refuse-bank fires by proper construction of banks are described.

Jan 1, 1964

By Walter Frank

The purpose of the work covered by this contract is to develop a ground and pilot conductor connector which will significantly improve mine trailing cable splice performance. This work compliments the work completed under Contract 00357100 on the development of crimp connectors for the phase conductors of trailing cables. A brief discussion on splice problems is presented as an introductory means and substantiates the need for the development and test programs outlined in this report. As with the phase development work, the ground and pilot connector work is essentially of an empirical nature. As a result time is devoted to explaining the derivations of the test procedures used. In order to familiarize the reader with connector terminology a section is devoted to a glossary of pertinent terms. The connector design effort includes connectors for splicing ground and pilot conductors. A distinction is made between connectors suitable for splicing round and flat ground configurations. The same also applies to the pilot conductors. During the course of this work, much time has been devoted to the question of suitability of round cable configurations for trailing cable applications. This is discussed in detail along with resulting conclusions and recommendations. A field test program was conducted in order to confirm ground and pilot connector laboratory data. This testing also determined the viability of the connector designs and recommended installation techniques in a mine environment.

Jan 1, 1979

By D. D. Bush

Based on the results of this study, the underhand cut and fill stoping method, with mass destressing, is an effective method for controlling rock bursts and falls of ground for deep mining in the Coeur d'Alene Mining District. The procedure can be utilized to pull highly stressed pillars by converting from conventional overhand stoping methods or used as a primary recovery system. During the demonstration, only one minor rock burst occurred, with no injuries. The system facilitates accurate placement of vertical boreholes for effective mass destressing. Each mining cut is filled with cemented sandfill overlying a timbered mat that forms the back for the succeeding cut. For this demonstration, a cemented fill was mixed on the surface and piped to the stone. Costs for pillar recovery by this method are comparable and are considered cost effective over conventionally timbered overhand mining as a pillar recovery method.

Jan 1, 1982

By A. Tewarson

Combustibility data are presented for 14 samples representing commonly used mine materials (treated and untreated wood, conveyor belt and brattice cloth). The combustibility data were obtained in the Factory Mutual Small-Scale Combustibility Apparatus (sample area -0.008 m ). The hazards associated with the mine materials were evaluated in terms of: 1) ignition/ surface flame spread using an ignition parameter (IP). A reasonable correlation was found between IP values and U.S. Bureau of Mines ratings for conveyor belts and brattice cloth and large-scale fire test data for treated and untreated timber sets; 2) generation of combustible vapors, using a vapor generation parameter (VP); 3) heat release using a heat generation parameter (HP). A reasonable correlation was found between HP values and the large-scale fire test data for treated and untreated timber sets; 4) generation of "smoke," toxic and corrosive products using a chemical compound generation parameter (CP); and 5) light obscuration by "smoke" using the light obscuration parameter (LP). All the wood treatments, except Fireguard, were found to be effective in reducing the fire hazard. The effectiveness of the treatment appears to be due to enhancement of carbon formation in the solid phase and enhancement of water formation in the vapor phase. Concepts are presented for establishing 1) the relationship between various parameters (IP, VP, HP, CP, and LP) and basic properties of materials, and 2) the usefulness of the parameters as criteria for the combustibility and fire hazard evaluations of the mine materials.

Jan 1, 1982

By W. F. Watts

This report describes the Mine Inspection Data Analysis System (MIDAS) developed by the Bureau of Mines to analyze the records of industrial hygiene samples collected by the Mine Safety and Health Administration (MSHA) in metal and nonmetal mines. MIDAS is the first system capable of sorting, editing, analyzing, and reporting these data. It is also the first system designed to be used by a number of Government agencies. At present the system contains 225,000 personal and area samples for 61 contaminants in 45 industries. The records date from 1974 to early 1980, and MSHA plans to provide yearly updates to the system. This report presents preliminary analyses of dust exposures and discusses the potential uses and limitations of these data. Analysis of the dust data for 1978 and 1979 showed that bagging had the highest percentage of dust overexposure. Morn than 40 pct of the 1,536 respirable quartz dust, total nuisance dust, and total silica dust samples exceeded the MSHA exposure limit. Other dusty occupations are ranked according to their percentage of overexposure.

Jan 1, 1981

By F. D. Everett

The Burgin shaft of Bear Creek Mining Co. near Eureka, Utah, was sunk during 1956 and 1957 as part of an exploratory program, searching for lead, zinc, copper, silver, and gold ore bodies hidden from the surface by several hundred feet of volcanic rocks. This paper describes the sinking methods and operating practices of Centennial Development Co., contracting firm for Bear Creek Mining Co., in sinking a 3-compartment vertical shaft 1,100 feet. The operation featured the Cryderman positive-action, clam-type shaft mucker. The shaft was completed in 142 days by a shaft crew of 10 men and a top force of 10 men, including supervision.

Jan 1, 1959

By Wils L. Cooley

This report analyzes electrical accident data in the metal/non-metal mining industry. Accidents are categorized to determine their root causes. Special attention is given to accidents associated with inadequate or defective grounding of mine power systems. Recommendations are made concerning proper grounding practice, especially for dredges and for quarries in hard rock or sand. The costs of instituting the recommended practices are estimated for model mine power systems which are based on field data obtained from 37 mines and several electrical contractors. The expected benefits of various suggested safety practices are also estimated.

Jan 1, 1981

By V. F. Parry

[Approximately 7-1/2 million tons of subbituminous coals are mined annually in Colorado, Wyoming, and Montana, of which 50 percent probably reaches domestic consumers. The moisture of these subbituminous coals is high, averaging about 25 percent when they are mined. The coals are non-caking end stack to a variable degree when exposed to normal atmospheric conditions. They are good domestic fuels, are considered to be smokeless in most furnaces, and have been used for many years in hand-fired domestic furnaces in which the practice is to employ large lutes for efficient combustion.]

Jan 1, 1941

By August J. Kwitowski

This Bureau of Mines report summarizes the development of a protective operator compartment for a new generation thin-seam mobile bridge carrier. The developed compartment is commercially available and is currently employed on approximately 15 bridge carriers used in the mining industry. The design of the compartment, which employed human factors engineering and small- and full-scale mockup models, is fully described. Details of the compartment's fabrication, evaluation, and demonstration in a commercial low-seam coal mine are also provided.

Jan 1, 1986

By G. R. Hopkins

"Summary An apparent decline in fuel efficiency at refineries, which first became came evident in 1930 and continued through 1933, was checked in 1933 when the average amount of heat needed to refine a barrel of crude oil amounted to 660,000 B.t.u. This compares with an average requirement of 692,000 B.t.u. In 1932 and with a low of 639,000 B.t.u. in 1929. (See fig. 1.) The improvement in fuel economy in 1933 probably was closely related to the increase of 5 per cent in crude runs to stills. As much of the fuel burned at refineries is utilized for purposes other than under crude-oil stills and in relatively stable amounts, it is evident that a material increase in crude runs will usually reflected in a decrease in average fuel requirements. Another factor which has influences fuel economy at refineries in the past is the trend in cracking, a refining process requiring more than the average expenditure of heat. In 1933 production of gasoline by cracking increased slightly, but no appreciable rise in heat requirements resulted as an equivalent amount of fuel was saved in improved technique, particularly in the field of heat exchange.Since the beginning of the refining industry, the transition in fuels has been from solid to liquid to gaseous; in other words, the leadership was first held by coal, then passed to oil, and is now held by gas. In 1933, 54.7 percent of the total heat units generated came from gas, 39.0 percent from oil (including acid sludge), and 6.3 percent from coal and coke. The principal change in the relative importance of the various refinery fuels in recent years has been the rapid growth in consumption of refinery or still gas at the expense of all the other common fuels. Still gas owes its ascendency to its cheapness and availability, and probably it would have become the primary refinery fuel years ago if recovery methods had been perfected. The relative importance of coal showed a small increase in 1933, the first gain recorded since these surveys were inaugurated in 1925. The increase in use of coal was undoubtedly due to increased operations at plants using it,"

Feb 1, 1935