Search Documents

By V. Ferrari

This report documents the three-phase program to design, fabricate, test, and demonstrate economical and practical methods of reducing noise levels on underground coal mining portal buses (mantrip vehicles). The noise-control treatments applied to a production-model portal bus were as follows: ? Wheel/rail vibrations were isolated from the vehicle frame by inserting elastomeric materials between suspension components. ? Vibration-induced noise was reduced by replacing all large sheet metal panels (except floor plates) with damped steel panels. ? Motor noise was reduced by tight-fitting covers made from damped steel and lined with sound-absorbing material, and by elastomeric motor mounts. ? The standard spur gears used in the traction drive system were replaced with helical gearsets. The program achieved the goal of reducing the average sound-level to below 85 dBA for typical operating conditions.

Jan 1, 1981

By A. B. Hooker

The flame safety lamp with metal-gauze enclosure was invented by Sir Humphrey Davy more than a century ago, primarily for its safe light; however, it soon became the standard device for detecting the presence of methane in mine atmospheres. It still is the most widely used device for this purpose and is also the most practicable means of detecting deficiency of oxygen in coal mines. A permissible flame safety lamp is similar in all respects to one that, after a series of tests, has been approved by the Bureau of Mines as safe for use in gassy mines. However, safety depends largely upon the way lamps are maintained and used.

Jan 1, 1944

By H. W. Brandt

A field test was designed to inject a specially formulated two compound epoxy resin into the roof rock ahead of a working face to cement fractures and formation interfaces at the Westmoreland Coal Co., Winding Gulf Div., Eccles No. 5 Mine, Eccles, West Virginia. Five 30 foot long X 2 inch diameter, hold were drilled at an angle of 15° above the plane of roof line front the face of a working entry. The epoxy resin compounds were pumped through a proportioning unit and mixed in-line before being discharged into the drill hole under treatment it injection pressures up to a maximum of 450 psig. When the coal face was advanced an anomalous failure of the roof rock occurred in the treated section. Further testing was suspended until the cause of the failure could he determined. The polymers were tested, under confined conditions, in 2 inch pipe columns. Extreme temperature and pressure (up to 2400 psig) rises were recorded as they cured, It was concluded that this pressure source fractured the rock and caused the roof failure. The entire program was terminated after it was determined that the heat rise and resultant high pressures could not he controlled chemically or mechanically.

Jan 1, 1978

By Joan Weinberg

Real gross national produce (GNP) grew at a seasonally adjusted annual rate of 2.0% in the fourth quarter (table 1). The restrained quarterly growth rate was the slowest in 2 years, and was substantially slower than the 2.5 % rate of the previous quarter. According to the U.S. Department of Commerce, the summer drought reduced the fourth-quarter growth rate by 1.1 percentage points. A growing trade deficit and a reduction in business investment were the key economic factors curtailing growth. The trade deficit widened by $6.8 billion, reflecting both a surge of imports and a slowing of exports. Business investment declined 3.7%, mainly as a result of a slowdown in computer sales. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 3.8% for 1988, the fastest in 4 years, despite the drought. However, on a fourth-quarter-to-fourth-quarter basis, real growth measured 2.7%. Increased exports and business spending for plant and equipment accounted for much of the 1988 GNP growth. Employment continued to grow as the manufacturing sector added 414,000 new workers (table 2). Of these, the primary metals industry added 26,000 workers, and the clay, glass, and stone industry added 10,000. The civilian unemployment rate remained low throughout 1988, fluctuating between 5.3% and 5.4% during the last quarter.

Jan 1, 1989

This report presents production and delivered costs for coal exports from the five major Western coal-exporting countries: Australia, Canada. Colombia, South Africa, and the United States. Cost data were compiled from visits to 43 mines by U.S. Bureau of Mines engineers between 1985 and 1990. All report costs are in January 1989 U.S. dollars per short ton. Production costs for raw coal are divided into mining and regulatory categories. Costs are broken down by type of cost, type of mine. and country. Scheduled operating and capital costs for raw coal were processed by the Bureau's MINSIM discounted cash flow program to determine total production costs calculated at 0% and 15% discounted cash flow rates of return (DCFROR). Delivered costs are for salable coal delivered to various markets. Costs are broken down by supply country, market, and type of cost. Scheduled operating and capital costs for salable coal were processed by the Bureau's MINSIM discounted cash-flow program to determine total salable coal costs at 0% DCFROR. Added to total salable coal costs were transportation and port costs to get delivered costs. Comparative overview information on the coal industries of the five study countries are appended. This appendix includes information on industry economics and exports, production and reserves, and coal industry issues.

Jan 1, 1993

By Peter Murphy

This report (arid related appendices) provides a description of the functional design specifications, engineering design specifications, and program of instruction for development of a training system for dragline equipment operators. Based upon a task analysis and training system analysis prepared under Phase I, Phase II efforts expanded upon and refined the functional design specifications. The training hardware components have been developed to a point shy of system fabrication. A detailed outline of the porgram of instruction and content sequence has been prepared. The objective of the training system described in this report is to provide new operators of dragline equipment with the requisite skills and knowledge to assure cost-effective development and an adequate supply of our human resources.

Jan 1, 1976

By W. W. Adams

With production of coal per man-hour of work highest in history, the coal mines of the United States established a lower accident-frequency4 rate in 1942 than in any year since 1930, the first for which the Bureau of Mines, United States Department of the Interior, collected complete reports of nonfatal as well as fatal injuries. Reports from mine operators and State mining departments showed that 530,861 men were employed in and about coal mines during the calendar year 1942. This number does not include office employees or coke-oven workers. The figure represents a decrease of 15,831 men from the previous year, owing to losses of men to the military services and to more lucrative employment in the munitions and other industries. The loss of men was offset to some degree by an increase in the number of days of mine activity and the average number of hours of work per man during the year. The volume of work done during 1942 was 910 million man-hours, 11 percent more than in 1941. The average employee worked 243 days, 30 days more than in 1941. Production reached the unprecedented total of 640 million short tons, an increase of 12 percent over 1941; 582 million tons came from the bituminous fields of the United States and 58 million tons from the anthracite fields of Pennsylvania. To produce this quantity of coal 1,471 men sacrified their lives, and 69,564 men suffered nonfatal injuries that disabled them for more than the remainder of the day on which the accident occurred. The nonfatal injuries were divided into three groups: 65 caused permanent total disability, 2,045 caused permanent partial disability, and 67,454 caused temporary disability of 1 day or more but did not result in the loss of, or permanent loss of use of, any part of the body.

Jan 1, 1944

By Karl E. Starch

This Bureau of Mines report is a background study of severance taxes on mineral production. The rates, bases, and other features of State severance tax legislation as of March 1978 are presented, as are the amounts of State severance tax collections for fiscal year 1977, Some statistical comparisons between severance tax collections, total State tax collections, and total value of mineral production in the States involved are presented to portray the relative importance of severance taxes both in State tax revenue systems and in mineral industry revenues. A general discussion of the purposes and principles of taxation, the unique nature of a mining enterprise, the various types of taxes imposed on mineral production, and the character and rationale of the severance tax and its impacts on mining firms sets the severance tax in perspective. A bibliography of materials on the severance tax is included.

Jan 1, 1979

By Dennis S. Kostick

Salt is a universal mineral commodity used by virtually every person in the world. Although a very common mineral today, at one time, it was considered as precious as gold in certain cultures. This study traces the material flow of salt from its origin through the postconsumer phase of usage. The final disposition of salt in the estimated 14,000 different uses, grouped into several macrocategories, is traced from the dispersive loss of salt into the environment to the ultimate disposal of salt-base products into the waste stream after consumption. The base year for this study is 1990, in which an estimated 196 million short tons of municipal solid waste was discarded by the U.S. population. Approximately three-fourths of domestic salt consumed is released to the environment and unrecovered while about one-fourth is discharged to landfills and incinerators as products derived from salt. Cumulative historical domestic production, trade, and consumption data have been compiled to illustrate the long-term trends within the U.S. salt industry and the cumulative contribution that highway deicing salt has had on the environment.

Jan 1, 1993

By K. H. Johnston

This guide was written to furnish the coal industry with a description of techniques, instruments, and clues on how to find abandoned oil and gas wells that have penetrated coal seams. The report includes specific information on searching techniques currently in use by several coal mining companies, gas-transmission companies, and waterflood operators, as well as information on State agencies responsible for the enforcement of laws and the preservation and distribution of data pertaining to the drilling, development, and abandonment of oil and gas wells. Comparative tests were performed with several commercial electronic metal detectors to determine the feasibility of using them to aid in the search for abandoned wells and to determine the instrument most suited for that particular use. The role of methane detectors to locate abandoned wells is described, including a case history. Tests were made to develop an efficient procedure to follow in systematically searching an area for metallic clues or hydrocarbon evidence to abandoned wells. The guide describes, in detail, a search sequence, including the collection of basic data, preparation of the selected area, and the physical search. Methods are given for evaluating the results.

Jan 1, 1973

By W. T. Westbrook

This Bureau of Mines report contains methods for analyzing iron are for total iron, ferrous iron, metallic iron, silica, manganese, aluminum, calcium, magnesium, phosphorus, titanium, carbon, sulfur, moisture loss, and ignition loss by wet chemical methods. Some are modifications of standard umpire methods; others have been developed by the Bureau of Mines to provide a com-bination of speed and accuracy. They are suitable for a high volume of samples and/or control situations, and for situations in which instrumental results must be verified. These methods have been used to analyze taconites, native ores, some foreign ores, and metallurgical products.

Jan 1, 1975

By Jan C. Still

The Haines-Klukwan-Porcupine subarea of the Juneau Mining District (JMD) is located in the northern portion of the JMD and consists of the land between the Alaska-British Columbia boundary, the Chilkoot Valley, Glacier Bay National Park boundary, and extending south to the Davidson Glacier and the Chilkat Peninsula and Islands (fig A-I). This area was studied as part of the larger JMD study in a cooperative effort between the Alaska Division of Geological and Geophysical Surveys (ADGGS) and the Bureau during 1985 to 1988. Prior to this, during 1984, the ADGGS and the Bureau cooperated in a study of the Porcupine mining area and during 1981 to 1983 conducted separate studies in the area. Field work was conducted by foot, boat, truck, and helicopter. Figure A-I shows the Haines-Klukwan-Porcupine sub-area and shows the areas covered by previous Bureau and ADGGS studies. PHYSIOGRAPHY AND CLIMATE The physiography of the subarea ranges from gentle to rugged. Glaciers formed the major features in the sub-area and left "U" shaped steep walled valleys and rugged mountains. The Chilkat, Chilkoot, Klehini, Tsirku, and Takhin are the major rivers in the subarea. The higher mountains are glacier clad and some valleys still harbor glaciers that reach the valley floors. Lush forests and dense brush predominate up to timberline at about the 2,000-foot elevation. Low point in the subarea is at sea level in the area around Haines while the high point is 7,434 feet at: Mount Henry Clay in the Porcupine mining area.

Jan 1, 2012

By Merwin H. Howes

In constructing the NORAD Combat Operations Center, controlled blasting techniques were employed to achieve smooth walls and to avoid shattering the rock beyond excavation lines. Extraordinary measures were taken to stabilize the rock to permanently preserve the openings. Rock stabilization was accomplished by means of reinforced concrete and gunite linings, rock boltings, installation of chain-link fabric, and epoxy resin and cement grouting. A particular zone of weakness at B vital location was supported by exceptionally thick reinforced concrete lining, rock bolts, and cement grout.

Jan 1, 1966

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace- time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200- foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace-time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200-foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

By D. Harrington

Along with other phases of mining , the ventilation of metal mines has been affected by the business depression of 1930. As might be expected , some of the results are favorable , and some are distinctly disadvantageous to progress . Probably the worst effect of the recession of mining activity is that , as usual , one of the first departments of almost any industrial establishment ( and this is especially true of mining ) to be curtailed is that which concerns what might be called welfare work , such as safety , health , etc. , and ventilation : in consequence , a number of men who were employed mainly on ventilation work in metal mines are now out of employment and their former duties either are being handled by others as only part of a crowded routine or are being allowed to lapse . On the bright side of the picture is the following paragraph from a letter by the ventilation and sarety engineer of the United Verde Copper Co. , Jerome , Ariz . , indicating that money and effort expended on ventilation during " flush " times give results which aid in money savings when depression comes : The desirability of absolute control over the ventilation system has again been demonstrated at this mine . Under full operation we have been using approximately 500 hp . to drive our big fan . Under curtailed operations we naturally do not require as much air , so by sending the air only where needed and airing out all other places periodically to keep timber , etc. , in good condition we have been able to economize in the quantity of air required . The fan speed has been reduced and the power dropped to 300 hp . , thus effecting a material saving in the power bill , and still maintaining an efficient ventilating system . "

Jul 1, 1931

By John C. Machisak

The Nation's mining and quarrying industries have again met the annual challenge to their ingenuity--that of reducing disabling work injuries among their employees. The effectiveness of management in facing this problem and in meeting this responsibility is evident from the results of the 1961 National Safety Competition. Three hundred ninety-three or 45.3 percent of the mines and quarries participating in the competition established a new record number of participants operating throughout the competition year without a disabling work injury. Another record established in the 1961 contest was the number of participants (868) enrolled in the competition. This annual safety competition was begun in 1925 and is conducted by the Bureau of Mines, U.S. Department of the Interior. It provides for six bronze Sentinels of safety trophies which are awarded each year to the winning participant in each group. Since its inception, the competition has exerted a strong influence in the field of safety promotion. The statistical record of its accomplishments over the years gives strong support to the theory that well-organized and well- administered safety programs are effective tools to be used to reduce the number of disabling work injuries. It stimulates and holds the interest of employees and management in accident prevention. Because of this, mines and quarries participating in the contest have a more favorable safety record than those operations not enrolled.

Jan 1, 1963

By Robert W. Van Dolah

The prevention of fires and explosions involving the combustibles and oxidants likely to be found in flight vehicles requires a knowledge of the flammability and related characteristics of these materials. This circular is a compilation of the available charactersilics data for a series of combustibles and oxidants of current interest. Vapor pressure data are presented for fluorine, oxygen, chlorine trifluoride, nitrogen tetroxide, nitric acid, hydrogen peroxide, ethylene oxide, hydrogen, ammonia, pentaborane, unsymmetrical dimethylhydrazine, monomethylhydrazine, hydrazine, and a series of hydro-carbons including decalin, tetralin, bicyclohexyl and other high-density fuels. In addition, flammability characteristics diagrams are included for each of the fuels in contact with air and, where available, other oxidants (for example, oxygen and nitrogen tetroxide). To assist in understanding these data, sections on definitions and theory and applications have been included. Each section is complete in itself and can be used separately. For example, a reader who is familiar with the general theory of combustion and detonation may find the data sections more useful than the definitions and theory and the application sections. However, since pertinent data are included in these sections, they should also prove useful to the experienced engineer interested in preventing fires and explosions.

Jan 1, 1963

By S. H. Ash

THE INVESTIGATION of barrier pillars in the Western Middle field is part of the comprehensive study of the mine-water problem in the anthra¬cite region of Pennsylvania by the Federal Bureau of Mines (1, 2, 5, 6, 7, 8,9,10,11,1,2,15,16).8 The Western Middle field is in Schuylkill, Columbia, and Northumberland Counties in eastern Pennsylvania. It has an area of 120 square miles, is 42 miles long from Delano on the east to Trevorton on the west, and is 2 to 5 miles wide. In the Western Middle field are 58 underground water pools containing 38 billion gallons of water (5). Some of the pools overflow to the surface, and the water from others seeps into adjacent mines through permeable barrier pillars separating them from abandoned mines. Several active mines are interconnected to workings in abandoned mines, which are partly filled with water. These mines are separated by barrier pillars that are considered effective only below the altitude of the connections. In some abandoned mines, pumping stations maintain the water at altitudes where the hydrostatic pressure against the barrier pillars is not excessive and does not endanger adjacent active mines. If water in these abandoned mines is allowed to rise to where it can overflow into the active mines, it must be pumped from the active mines at lower altitudes; this materially increases the cost of pumping. It is estimated that from 1944 to 1948 approximately 30 percent of the water pumped to the surface was from abandoned mines.

Jan 1, 1953

By Wadaw Cybulski

The problem of coal dust explosions: Basic information about the explicability of coal dust: Main parameters of the explosibility of coal dust; Main parameters of the explosibility of coal dust; Limit explosibility of coal dust and its dependence upon the basic parameters: The effect of the initiator of the explosion-on-the explosibility of coal dust: The dependence of the course of an explosion upon the distribution of coal dust in the workings, upon the dimensions of the workings, the length of zones, the direction of the development of explosions and upon the content of firedamp in the air of the workings; Con-sequences of coal dust explosions; The ways of suppressing the danger of coal dust explosions; Stopping the developed coal dust explosions; The explosibility and explosions of lignite dust of xylite structure

Jan 1, 1975