Search Documents

By Jessie L. Bonner, W. Stephen Blomberg, Mark Leidig, Heather Hooper

Understanding the effects of the bench on ground motion can improve the design of cast blasts and achieve improved blast efficiency while remaining below vibration requirements. A new dataset recorded in September 2003 from a coal mine in Arizona has allowed us to examine the excitation of short-period Rayleigh-type surface waves from four simultaneously-detonated explosions in and below a topographic bench of a mine. The explosions were recorded on a network of over 150 seismic sensors, providing an extensive understanding of the ground motion radiation patterns from these explosions. We detonated two separate explosions (~3 tons and ~1.5 tons ANFO) in the deepest pit of the mine, thus the explosions were shot to solid rock. Within 25 meters of these two explosions, we detonated two additional explosions of similar explosive yields in a bench, thus these explosions were shot to the free face. Radiation patterns and spectral ratios from the explosions show increased amplitudes (by a factor of 1.5 to 2) at azimuths behind the bench relative to the amplitudes in front of the bench. We compared these findings to seismic observations from two ~1.5 million pound cast blasts at the same mine and found similar radiation patterns. Modeling of these blasts shows that the variations in ground motion are caused by the topographic bench as a result of 1) horizontal spalling of the rock falling into the pit and 2) non- linear scattering near the free- face. We also note that shooting to a buffer (previously blasted rock) causes the azimuthal variations to be significantly reduced.

Jan 1, 2005

When a company has an effective hearing loss prevention program, everyone wins-the employers, the employees, and the safety and health professionals who implement the program. This guidebook is not about minimal programs that meet only the letter of the law. It is concerned with programs that are effective as well as efficient: those optimizing program elements that succeed in preventing hearing loss in a practical and cost effective manner.

Jan 1, 2006

By Kenneth Eltschlager, Jim Ratcliff, Michael Mann, Edward Sheehan

The Appalachian Blaster Certification Delegation initiated a study to compare the consistency of measurements from blasting seismographs. Six blasts were monitored at surface coal mines in West Virginia, Maryland, and Ohio. A total of seven different makes were deployed during the tests, with as many as seven models from five different manufacturers compared during any one blast. Great care was taken to bury the geophones in identical fashion. The variations in seismograph readings were compared to the International Society of Explosives Engineers’ Performance Specifications for Blasting Seismographs. Between 4 and 125 Hertz, the ground vibration amplitudes should be within ±5% and airblast amplitudes should be ±1 decibel. For each of the three mutually perpendicular ground vibration channels and the acoustic channel, the median value of all the units was used as a baseline for comparison. The six blasts monitored had median peak particle velocities ranging from 0.42 to 3.47 inches per second (in/s) (10.7 – 88.1 mm/s) and median airblasts ranging from 124 to 135 decibels (dB). There were 46 seismograph recordings for the six blasts. Eighteen (39%) of the 46 maximum peak particle velocities varied more than ±5% from the median. A total of 138 (3 × 46) component particle velocities were recorded, with 50 (36%) of the readings varying more than ±5% from the median. For airblast comparison, 43 recordings were obtained, with seven (16%) varying more than ±1 dB of the median. Variances may be attributable to blasting seismograph differences, variations in field deployment, and relative locations of the geophones. Full waveform seismic and acoustic overlays for individual blasts showed encouraging conformity with some slight anomalies

Jan 1, 2015

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes.

Feb 1, 2020

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes. Accurately capturing and modeling this geology is the key to controlling high air blast. 3D modeling and profiling by drone is the solution to understanding accurate face profiles and real minimum burdens. Using 18 months of blasting data and air blast results to establish a baseline, the comparisons between blasts designed with 2D profiling and blasts designed with drone 3D profiling show improvement in air blast levels. Additionally, shots with completed drilling were drone profiled to understand precise amounts of burden for each borehole. This 'audit' of a blast allows for custom loading of explosives, accommodating the amount of burden present on the blast face. 3Dprofiling is not a new tool in the blasting industry, but a drone alleviates some of the restrictions ground systems face. Controlling and managing air blast, as it pertains to face burdens, requires an understanding of those burdens from all angles. A drone provides that distinct level of insight. The results of this study indicate that drone profiling is managing the customer's air blast readings, allowing the customer to maintain their license to operate within the community.

By William Reisz

Many different types of drills coming in a wide range of sizes and configurations are used in the blasting industry today. While each system may have its own unique attributes and capabilities, it may hold its own perils as well. This article will focus primarily on hazards that are mutual to most every type of drilling system.

Jan 1, 2013

By Braden Lusk, Tristan Worsey, Nathan Rouse, Kyle Hall

Loading explosives up hole has challenges that are typically not seen in down hole explosive loading. Most explosives applications are not up hole. Lack of experience and technology can cause significant problems when loading explosives up hole. When results aren’t achieved, the blame is commonly put on the design when the true problems are unknown. Not knowing the cause of the problem causes drill and blast designs to be over engineered and very costly with little success. Being able to know and record key data is crucial to actually solving the problem. This paper goes over blast instrumentation that can be used to trouble shoot drill and blast problems in up hole explosives loading in underground mines. The tools and procedures used to trouble shoot include velocity of detonation recorder, borehole tracking, seismographs, and borehole camera. Each item will be discussed in detail with a case study to show the usefulness of the instrumentation. The operation discussed in the case study had issues pulling raises and had hang ups in the stope shots. These problems caused production slowdowns and costly remediation blasting that was not very successful. The case study is an underground gold mine that used modified sub-level caving with backfill as the mining method.

Jan 1, 2018

By Jane Wright, Brent Blanchard

Question: When it comes to demolition projects, what could be more demanding than asking a blaster to explosively demolish a stubby, heavily-reinforced concrete structure in the heart of a third-world country? Answer: Asking them to fell only half. Such was the charge recently put forth to Controlled Demolition Group (CDG), Yorkshire, UK when they were called to Casablanca, Morocco to provide a stunning demolition effect for the upcoming Universal Pictures film Spy Game, starring Robert Redford and Brad Pitt. Director Tony Scott (True Romance, Enemy of the State) contacted the renowned demolition firm after seeing their work on television and receiving recommendations from explosives manufacturers. The film’s producers then asked the CDG team if they could bring down half of an apartment block as part of a dramatic suicide bomber sequence.

Jan 1, 2002

In all the industries that require blasting operations using explosives, there exists numerous unwanted side effects of the blast which may pose as environmental hazards. These hazards face prominence, especially in India, where there are very stringent rules and regulations governing the use of explosives. The environmental hazards associated with blasting operations as a whole can be tacked successfully to a certain extent depending upon the ultimate expectations of ,the post-blast effects and the limitations of the environmental obligations as specified by the authorities from time to time and from place to place. The main parameters which require attention to limit the post-blast results to the optimum level are ground vibrations, dust pollution, gas pollution, air blast effects, noise pollution & fly rocks etc.

Jan 1, 1995

"AQUILA Mining Systems Ltd. is a Canadian company that designs and develops monitoring, control and navigation systems for the surface and underground mining industries. In 1992, AQUILA Mining Systems began the development of technology for monitoring, controlling and positioning mobile mining equipment. In 1993, AQUILA completed its first field test with GPS receivers onboard ablasthole drill, and thus demonstrated the viability and strategic relevance of this technology in surface mining. Since then, AQUILA has installed GPS-based technology on drills and shovels in several Canadian mines. This paper will review the development of these systems and discussthe benefits the mining industry could realise through their production implementation."

Jan 1, 1997

By Neil T. Davie, Thomas K. Blanchat, Thomas C. Togami, Joe R. Weatherby, Dale S. Preece, Robert A. Benham, James J. Calderone

"Geotechnical structures ,such as underground bunkers, tunnels, and building foundations aresubjected to stress fields produced by..the gravity load on the structure and/or any overlyingstrata. These stress fields may be.. reproduced on a scaled model of the structure byproportionally increasing the gravity field through the use of a centrifuge. This technology canthen be used to assess the vulnerability of various geotechnical structures to explosive loading.Applications of this technology include assessing the effectiveness of earth penetrating weapons,evaluating the vulnerability of various structures, counter-terrorism, and model validation. Thisdocument describes the development of expertise in scale model explosive testing ongeotechnical structures using Sandia’s large scale centrifuge facility. This study focused onburied structures such as hardened storage bunkers or tunnels. Data from this study was used toevaluate the predictive capabilities oft existing hydrocodes and structural dynamics codesdeveloped at Sandia National Laboratories (such as Pronto/SPH, Pronto/CTH, and ALEGRA)."

Jan 1, 1998

By Jose a. Sanchidrian, Ramon G. Eguren, Javier L. Amigo

On December 2013 a MEMU exploded at a blasting site in Norway, after burning for more than two hours. This paper describes the analyses made to determine the actual yield of the explosion, the lessons learned from the event and the actions taken as a consequence. The conclusions of the analysis were the following: - The yield of the explosion was 650-1450 kg TNT. In terms of AN and ANE they correspond to 1300 – 3700 kg AN, or 950 – 2450 kg ANE or ANE/AN blend. These quantities are 8 to 31 % of the explosive precursors in the truck. The burning of the truck and its load for two and a half hours had consumed more than two thirds (perhaps up to 90 %) of the explosive precursor material.

Jan 1, 2016

By Conny Postupack

The first principle one usually learns about blasting is that competence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced in a new area, may have co make one or two himself to the new conditions with which he blaster when operating shots just to acclimate is faced.

Jan 1, 1991

By Enver Alan

This Research & Development (R&D) study was conducted in the field of applied blasting engineering in Ethiopia, within the AKH Railway Project, which was built in Girena, within the boundaries of the province of Mersa, in the Basalt Quarry at km 346, Ashangi Formation, occured in Eocene geological time in the aphanitic trachibasalt. Under the scope of the study, which has been performed to determine the effects of the artificial discontinuities at different depths and the effects of artificial discontinuities through structural damage risk, three test areas, at the same location and same formation, were considered. Six numbers of artificial discontinuities, each 10 m (32, 81 ft) transverse, were created by using pre-splitting and drilling-blasting technology. The number of sequential artificial discontinuities on each test area is two and they have the same length. The length of artificial discontinuities are; 6,80 m (22,31 ft) at the first test area, 13,60 m (44,62 ft) at the second test area and 17,00 m (55,77 ft) at the third test area respectively. The distance between sequential artificial discontinuities is 8 m (26,25ft) on each test area. Thirty-one shots were executed in order to produce vibration (10 shots on the first test area, 11 shots on the second area, 10 shots on the third test area). One hundred and twenty-three seismic recordings were obtained during the execution of the shots by using 4 seismographs. The closest distance between the shot points and the nearest measuring station is 5,30 m (17,39 ft). During the shots, the rock was cracked and there was no fragmentation and/or fly rock. At the first test area, measured PPV values are between 25,40-127,00 mm/s (1-5 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. At the second test area, measured PPV values are between 76,20-177,80 mm/s (3-7 inch/s) before the first artificial discontinuity and less than 76,20 mm/s (3 inch/s) after the second artificial discontinuity. At the third test area, measured PPV values are between 50,80-279,40 mm/s (2-11 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. Peak reduction rates in Peak Particle Velocity (PPV) values determined by measuring as follows: In the first test area 95,77% (106,00 mm/s to 4,48 mm/s) (4,17 in/s to 0,18 in/s), in the second test area 79,77% (176,00 mm/s to 35,60 mm/s) (6,93 in/s to 1,40 in/s), in the third test area 95,85% (from 205,00 mm/s to 8,55 mm/s) (from 8,07 in/s to 0,34 in/s). The arithmetic mean of the differences of PPV values (decrease rate) is 82,66% in the first test area, 69,37% in the second test area, and 92,03% in the third test area. The highest sound value is 138,50 dB and is defined as “noise”. When the measured parameter values are examined it was determined on the USBM norm graphs that these vibrations carry a risk of structural damage in the region before the first artificial discontinuity. While passing through artificial discontinuities the vibrations progress by losing energy and the vibrations passing through two artificial discontinuities do not carry structural damage risk under current conditions.

By David Leidel, Beth Shimer, James Stuart

Periodically, the Institute of Makers of Explosives Safety Library Publications are reviewed, edited and updated to reflect recent technical developments, new commercial explosive products and new regulatory requirements. The rapid proliferation of electronic devices, particularly portable communication systems, inventory management devices, navigational aids, etc., required the revision of the IME Safety Library Publication 20, “Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators”. The new edition of SLP-20 has been updated to correct alterations to U.S. frequency allocations and maximum transmitted power permitted and a discussion of communications and tracking systems required in underground mining by the Miner Act. Also, an entire section was added dedicated to safe distances from RF sources to the special type of resistorized electric detonators used in the upstream oil and gas industry on wellsites and an enlarged section describing the particular types of RF sources that the blaster may encounter, perhaps in construction blasting operations.

Jan 1, 2012

By Peter Duniam, Stephen John Brace

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation and Explosives Applications Orlando,Florida,USA July24-27,200O. Objectives:- After completing this session 1. Explain safety issues 2. Do simple initiation design 3. Describe how the system works 4. Demonstrate scanning, hookup, testing and firing 5. Describe hot to do a post blast check 6. Explain how to treat misfired detonators

Jan 1, 2000

By Christian J. Sorensen, Christopher Armstrong, Andrew Matejunas

A team consisting of junior and senior mechanical engineering students at New Mexico Tech worked on the design of an explosively loaded vessel, with a maximum load of 15 grams (0.53 oz) TNT equivalent explosive. The main challenge presented was to meet the stringent sample positioning specification of 3 microns in two Degrees Of Freedom (DOF) and one degree of rotation in a third DOF. This is to accommodate precise sample placement in a tight x-ray beam, and to bring areas such as explosives/metal interfaces into magnified field-of-view photography. This presentation describes the process and design decisions to arrive at the final product presented to LANL in December 2014. Our engineering analysis techniques will be reviewed, including use of American Society of Mechanical Engineers (ASME) Boiling & Pressure Vessel Code (BPVC) Code Case for Impulse Loaded Pressure Vessels (ASME BPVC Code Case 2564-3). Also discussed will be integration of Hydrocode computer models with Finite Element Method analysis.

Jan 1, 2015

By Raden Haris Handayana, Jerri Mapanta, Eri Barlian, Milia Putri, Nasfryzal Carlo, Jihan Lubis

Waste oil is a growing problem throughout industries where environmentally responsible disposal ways are usually costly. There are many industries have developed process to reuse of waste oil as a source of energy on their own premises. Hanwha Mining Services Indonesia is one of blasting service that manufacturing explosive using waste oil. The usage of 60 % waste oil content in fuel solution already developed applied since 2020 at Petrosea-Kideco Site and will be increase until 100 % in 2022. The purpose of this research is to analyze the increasing of waste oil usage from 60 % to 100 % content at Petrosea Pit without reducing the emulsion quality and performance, and surely eliminate the fuel cost and reducing waste oil processing cost. Some trial conducted to determine the effect and quality of using 100 % waste oil content on emulsion at production blast. The method use to know the quality of 100% waste oil of emulsion is by direct application on bench blast. Using Microtrap VoD recorder, explosive energy will be recorded into m/s dimension, microtrap recorder the speed of explosive detonation in line with the speed of burning wire in the blast holes. The summarized of this research present that the using of 100 % waste oil content on emulsion can be applied on bench operation with the result of Velocity of Detonation (VoD) data is 4,559 mm/s, the mean of fragmentation size is in range 65.31 to 225.62 mm, the average of digging time on 1st layer is in range 10.2 to 11.6 s and on 2nd layer is in range 8.9 to 9.5 s, and the productivity still achieve on target. The result of all parameter quality still in the standard range of Hanwha and Petrosea.

Feb 6, 2023

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By Lon Santis

In 1923, Ralph Assheton compiled a report for the Institute of Makers of Explosives (IME) on accidental explosions in manufacturing plants. The report chronicles the type and amount of explosive involved in the event and the effects and distances to nearby buildings and workers for over 100 events from 1880 to 1916. Apparently, this report was never published but served as the origin of the IME’s first intra-plant distance table published in Pamphlet No. 3 in 1926. The effort was a parallel effort to the IME’s development of the American Table of Distances. The intra-plant distance table has never been changed by the IME and follows the US Department of Defense (DoD) standard very closely. This paper freshly compiles the data from the 1923 report and analyzes it with modern methods not generally available in 1923. Interestingly, the analysis indicates that the original intra-plant distance tables were established primarily to protect workers from serious injury and that preventing propagation was a side benefit. The data shows that a strong relationship exists between the probability of injury and the traditional K-factor. The data indicate that people in the open are better protected than those inside structures and that barricades reduce risk close to an event. Individuals at the intra-plant distance had a 95 percent chance of receiving no worse than a minor injury. A comparison of the data to explosive event consequence models indicate the models are overly conservative in regards to risk inside inhabited building distances.

Jan 1, 2010