Search Documents

By Luana Ferreira de Carvalho, Aurelio Manço Garcia, Gustavo Sampaio Lopes, Jose Silvio Corsini, Davi Bastos Martins de Oliveira

The Enaex Mining Technical Solutions (EMTS) team, in partnership with the Anglo American Iron Ore Brazil drilling and blasting team, has developed a study aiming to optimize the blast design applied at the Minas-Rio project. The study consists of modeling the dynamic behavior of one lithological domain to determine the best configuration of drilling pattern, charge configuration, timing and sequencing of the blast designs applied at the mine in this particular rock.

Feb 1, 2020

By Gregory B. Poole

Data collected with 16K sampling at a variety of blasting sites (construction, quarry, trench, mine) and monitoring locations was analyzed to effectively show the 16 different 1K readings all based on the microsecond that the unit went into monitoring.

Feb 1, 2020

By Adam Stremcha, John MacGregor

Initial planning called for 3 separate drop shafts and 3 separate vent shafts to be pulled back from the excavated tunnel with a large diameter raise bore machine. With time constraints and the raise bore machine already in high demand on other shafts, a more “traditional” drill and blast approach was taken on a few of the larger drop shafts. This decision proved to be not only cost effective, but also reduced schedule impact as the shafts were excavated simultaneously with the other raise bores.

Jan 1, 2010

By Thomas Kovalchuk, Kenneth Eltschlager, William Shuss

In April of 2000, two adults and their newborn infant, were poisoned by carbon monoxide in their home and received medical treatment at a Pennsylvania hospital. Carboxyhemoglobin levels were; child - 3 1%, father - 28Oh, and mother - 17%. Initially the furnace was blamed but after further review, blasting at a nearby coal mine was determined to be the source. All other sources of carbon monoxide were ruled out. The blasting was about 400 feet from the house. The conditions that led to the migration of gas include: the blasts were highly confined, the geologic structure contained fractures that served as conduits for the carbon monoxide to reach a hand-dug well outside the house, and the well was atmospherically connected to the basement floor drains.

Jan 1, 2001

By David S. Shatzer, Michael R. Purcell

Current world events have demonstrated the use of commercial vehicles, other unconventional modes of transportation and unusual materials as explosives or incendiary weapons, affecting commerce, disrupting cities and even entire societies. Since the implementation of the Organized Crime Control act of 1970 the Bureau of Alcohol, Tobacco, Firearms and Explosives (ATF) has been investigating and studying explosives and incendiary devices and their related effects.

Jan 1, 2004

By George D. Raitt, Rudy Lyon

Until fairly recently, Down-The-Hole (DTH or DHD) hammer drilling was never really a factor in large scale open pit surface mining. It was a method confined to water well drillers, aggregate quarries and limestone mines where the hole size rarely exceeded 6-1/2" (165 mm). Also it was somewhat limited to the harder rock areas such as the North East and South East United States. The trend in the big mining pits for coal, copper, gold and iron, was for the big rotary drill rigs with lots of muscle in pulldown, bitload and rotary torque.

Jan 1, 1998

By P Cotton, N Cox

The Brisbane City Council has implemented a program of continual improvement at its Mount Coot-tha Quarry in the heart of Brisbane, Australia. The program has been underway for the past 6 years, and has resulted in very significant improvements in terms of both the cost effectiveness of its operation, and in terms of its environmental impact on nearby residents. The work has included a focus, amongst other things, on blasting efficiency, and has challenged conventional thinking in terms of the size of blasts fired, the frequency of firing, the diameter of blastholes, and the use of bulk emulsion or slurry explosives.

Jan 1, 1995

By Terry Matts, Bruce Ripley, Clark Fletcher, Paul Rapp, Stan Holtby, Jim Dent

The Stave Falls Project of BC Hydro, situated 65km east of Vancouver, BC, Canada, involved the construction of a new two-unit 9OMW hydro-electric facility to replace an existing powerhouse. The final phase of the intake excavation consisted of a plug blast to break the channel through into Stave Lake. The plug consisted of a rock and till wall topped with a fill cofferdam, about 51m wide and between 8 and 12m high. Total rock volume was approximately 2600m3, overlaid with about 4600m3 of till/fill. This paper describes the methodology and practical techniques used in planning and loading the blast, and the precautions taken to protect the new and existing structures and equipment. Blasting of the plug by the normal method using downholes would have required the placing of extra fill and much drilling through casing, so the contractor made the decision to drill horizontal holes from the dry, downstream side. Because of poor rock conditions, all 183 holes had to be drilled oversize at 3.5” dia. and fitted with 2.5” id. plastic pipes to keep them open. Hole lengths ranged from 2.5 to 18rn, with a pattern of 1.5m spacing and l.Om burden (with the holes slightly fanned vertically). Because of significant water exposure, a film-packaged emulsion explosive was used, placed using a pneumatic cartridge loader for maximum borehole compaction. The powder factor averaged 1.3kg/m3 (2.21bs/yd3, rock only). An initiation system of combination surface/downhole delay shocktube units was employed, with double and triple redundancy. The maximum number of holes firing in any 8ms window was limited to three (to minimize vibration), while the whole sequence was fully activated before the first hole fired. All shocktube connections were secured and covered over at the foot of the rockface before flooding the excavation downstream of the plug prior to the shot, To protect the powerhouse gates from hydraulic shock, all hole collars were grouted and an air curtain was provided. The blast was completely successful. A maximum vertical displacement of 6m was recorded, but no flyrock was evident. Readings for peak over-pressure and vibration were well below the allowed limits. Mucking proved to be easy, with fine fragmentation, full pull, and no tights.

Jan 1, 2000

By Steven D. Knudsen, Dale S. Preece

The spherical element computer code DMC (Distinct Motion Code) used to model rock motion resulting from blasting has been enhanced to allow routine computer simulations of bench blasting. The enhancements required for bench blast simulation include: 1) modifying the gas flow portion of DMC, 2) adding a new explosive gas equation of state capability, 3) modifying the porosity calculation, and 4) accounting for blastwell spacing parallel to the face.

Jan 1, 1992

By Paul Worsey, Richard P. Ayres, Mark F. C. Schmidt

A new alternative technique designed to reduce rock scatter and flyrock during boulder blasting is being developed at UMR. The method uses small explosive charges and is designed for shooting in close proximity, while utilizing common blasting products found on the operators’ site. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique was published in last year’s proceedings. This particular portion of the work was performed as an undergraduate research project as part of the requirements for the explosives emphasis degree option at UMR. Previous model work was performed using cubes of concrete. However, in real life boulders are often flat and irregular rather than perfect cubes. The purpose of this work was to determine how to deal with flatter boulders. The work comprised using different geometry blocks (simulated boulders) of the same volume (1 cubic ft.). Square concrete boulders using an 8.5bag concrete mix were cast using different width to height ratios (varying from 1: 1 to 3.7:1). Single 5/8 inch holes were drilled to 2/3 the depth of the blocks, charges placed approximately l/2 way in to the holes and the holes filled with water. The explosive charges comprised ICI Masterdets containing a OSg High Explosive base charge and incremental added weights of C4 explosive. In the experiments, the block height was progressively reduced and to compensate the charge weight was increased until acceptable fragmentation was achieved. It was found that a significant increase in charge wt is required to achieve the same fragmentation as the width to height ratio increases (the boulder becomes flatter). Furthermore, the increase in charge weight required is proportional to the width to height ratio. Basically, you have to use a higher powder factor for flatter boulders.

Jan 1, 2000

By Walter Voglauer

On May 14, 2011 a chimney blast took place in Vienna, Austria. The blasting operation was part of the demolition works at a former railway fabrication. The demolition works on this ground were done under the leadership of the Austrian construction and demolition company PORR. In agreement with the civil organizations which were involved, the commander of the Regional Military Command of Vienna, Brigadier general Dr. Karl SCHMIDSEDER ordered a reserve force engineer company to demolish the chimney. The concrete planning of the chimney blasting was done by specialist Markus SEWALD who belongs to the HEERESTRUPPENSCHULE (combined armed force school) of the Austrian armed forces.

Jan 1, 2013

By D Vrkljan, Z Ester

There was no use of emulsion explosive at Croatia till 1997. Several attempts have been done to bear out the economical and technological affordability of applying the emulsion explosive for open pits and to make the contractor familiar with characteristics of emulsion explosive exepiting experimental blasts series at more open pits on different kinds of rocks. Testing the efficiencies of emulsion explosive there has been applied the original method for linear enlargement of burden of Sc.D. Josip Krsnik’s from Mining, Geology & Oil Faculty, University at Zagreb. The method of linear burden’s enlargement, in distinction from other methods concerning these problems, has been carried out in situ, under real exploitation conditions whereas the physical-mechanical rock’s features, geological conditions, bed relations and rocks’ structure influence the blast efficiencies. On such way, by mean of method the precise boring and blast sizes will be reached for each kind of rock and geological structural bed’s conditions referring to specific explosive type. The technical-economical analysis indicates the most favorable explosive type for specific bed.

Jan 1, 1999

By Ronald W. Roberts

For years, blasters have experienced near-misses, injuries, and yes, even fatalities as a result of the dangerous nature of our business. Yet, some blasters continue to portray the immortal attitude: nothing-would-or-could-ever-happened-to me syndrome. As we all know, that attitude can become disastrous to yourself or colleague(s).

Jan 1, 1996

By Q Liu, P D. Katsabanis

The energy output of crushed AN/FO, crushed AN/FO mixed with Aluminum (5%, 6.4% and 9.4% A1 by mass) and a commercial emulsion explosive has been measured using a detonation calorimeter. The charges had a diameter of 10 mm and were heavily confined by a 11 mm thick copper shell. In order to achieve stable detonation glass microballoons were used in the explosives so that the density of the AN/FO charges would be around 1.1 g/cc. The charges were detonated in vacuum and the detonation products were analyzed using gas chromatography. It was found that energy values were very close to calculated values obtained by ideal detonation codes.

Jan 1, 1993

By David G. Paton

"Electromagnetic surveys were conducted at the BXL Bulk Explosives Limited Mixing Plant andsurrounding area to characterize runoff from the site and possible impacts of salinity. The BXL Plant is located at the edge of a depressional area and any escape of soluble ions, such as nitrates, would have ended up in the slough to the west of the plant. Two electromagnetic (EM) instruments were used in the survey. A Geonics EM 3 1 was used in October 1997 and in June 1998, a new multifrequency instrument, a GSSI GEM 300 was also tested. Both instruments were individually mounted on a plastic sled with Teflon runners and towed with an ATV quad. Position was determined using a Trimble Pro XL global positioning system (GPS) with a real time correction mode Landstar receiver for an accuracy of about *l m. Both GPS and EM instruments were set to collect data at 1 second intervals. The quadrature maps for both instruments showed essentially the same information, namely of very high conductivity, appearing to emanate from the mixing plant. The levels of conductivity were highest where the saline water appeared to pool, at the southern end of the slough. Soil sampling locations were identified from the EM maps and navigated to using the real time GPS. Composite samples were collected by hand using a Dutch auger, from two locations, in increments of O-1 5, 15-30, 30-60 and 60- 90 cm. The analysis of the soil samples indicated a complete absence of nitrate or ammonium ions; the major anion was sulphate, indicating naturally saline subsoil conditions. The GEM 300 made the collection of data more efficient, as only one pass was required to collect the data from four depth intervals. The EM survey combined with the real time GPS allowed rapid characterization of the site with respect to soil salinity and proved to be cost-effective for Phase l/ Phase 2 site assessments and targeting sampling locations."

Jan 1, 1999

By Shuli Teng, Vladimir Sujansky, Matthew Rawls, Ivan Junarsa

In recent years significant advances have been made in chemical processing technology. In particular, process intensification using micro-technology has had some success in changing and improving chemical processes including mixing. Process Intensification is the miniaturization of unit operations and processes whereby a smaller compact piece of equipment takes the place of a larger one at the same given capacity or mass flow rate. This paper summarizes research into the application of the technology for manufacture of high internal phase water in oil ammonium nitrate emulsions (ANE’s) at low energy cost and with very low oil/fuel blend content. The emulsions can be used as precursors for preparation of explosives. The quality of the emulsion prepared was assessed through droplet and crystal analysis and compared with that of emulsions made by conventional large scale jet mixing technology.

Jan 1, 2014

By Francis Otuonye

Rock fragmentation by blasting still remains the most common and cost-effective method of excavating hard rock in mining and tunneling operations. During blasting, the dynamic stresses induced by the detonation of the explosive, in addition to fragmenting the rock in the vicinity of the blast, may fracture the rock at considerable distances from the point of detonation of the explosive. The fractures can result in reduced mine safety, increased costs to support the opening, low productivity and perhaps high ore dilution. Besides the dynamic stresses produced in the rock, air blast overpressure pulses are generated and propagate through the network of underground mine openings. The waves, unable to spread out spherically or hemispherically like blast waves from surface blasting, are forced to propagate by reflection from the roof, ribs and floor down the drift. Blast wave focusing can occur and produce intense shock waves that could damage ventilation barriers such as cement block stoppings.

Jan 1, 1992

By P D. Katsabanis, L Liu

Numerical modelling of fragmentation and throw is used to provide information on practical blast design parameters. The function of airdecking and its practical implications, the importance of the initiation point and aspect ratio of cratering charges and the timing between adjacent blastholes are investigated. Accuracy requirements for detonators are discussed with emphasis placed on the volume and fragmentation of the blasted rock, and compared to experimental results. Practical guidelines which have been based on intuition are examined using the model. Some of the predictions have been tested and correlate well with experimental results, obtained in the laboratory. Findings show that a minimum airdeck length is needed to realize any benefit from the application of airdecking in production blasting while the process can enhance the shock energy provided by non-ideal explosives significantly, bottom initiation of charges is beneficial to fragmentation and the aspect ratio for cratering charges can exceed the traditionally accepted ratio of 6. Regarding timing, in the ease of cratering charges, true simultaneous initiation shows beneficial results for the volume of blasted rock; however the accuracy required for practical detonators is very high. Fragmentation improves after a certain delay time while the optimum can be achieved at a range of delays. Timing affects muckpile shape; however it appears that subtle differences in delay times do not have a significant effect.

Jan 1, 1997

By Brandon Fryman, Josh Hoffman, Rhys Baker

A post-detonation debris collection project was led in conjunction with a large ammonium nitrate (AN) railcar detonation conducted by the Department of Homeland Security-Transportation Security Administration, Department of Defense-Combating Terrorism Technical Support Office, Sandia National Laboratories, and the U.S. Army Dugway Proving Grounds. This important work will aid in underpinning algorithms used in a Quantitative Risk Assessment (QRA) tool.

Feb 1, 2020

By James Stuart

A man died when the primed charge he was holding against his chest exploded. He was doing legitimate explosive work, and he was following all the safety procedures he had been taught. He and his colleagues had done this, thousands of times previously, with no ill effects.

Jan 1, 2007