Search Documents

By Sven Petersen

In April 2010 three REMUS6000 series autonomous underwater vehicles (AUVs) have been used to simultaneously map large areas near the Mid-Atlantic Ridge (3°N) axis in water depths ranging from 1,000m to 4,000m. One vehicle was provided by the Leibniz-Institute for Marine Science, IFM-GEOMAR (Kiel, Germany) the other two were provided by the Waitt Institute for Discovery (La Jolla, USA) and managed by the Woods Hole Oceanographic Institute (USA). The REMUS6000 vehicles, manufactured by Hydroid Inc. (USA), are "cigar-shaped" vehicles (4m long and weighing approx. 900kg) and consist of a tapered forward section, a cylindrical midsection and a tapered tail section. An internal titanium strongback, which extends through much of the vehicle length, provides the structural integrity and acts as a mounting platform for syntactic foam, equipment housings, various sensors and release mechanisms. The AUVs can be used in various payload configurations such as multibeam bathymetry, electronic still camera, or subbottom profiler. For these missions the electronic still camera configurations was installed. An EDGETECH 2200M dual frequency (120/410 kHz) side scan sonar was used to map the seafloor, but other frequencies are readily available for more options in resolution and range. The 120 kHz side scan transmitter was used for most missions in order to map large areas (increased range) and to be able to fly at higher altitudes (between 70m and 90m) above the rough seabed encountered in this area. The maximum slant range was between 600m and 700m on both sides resulting in a swath width of up to 1.2 km. Line spacing ranged from nearly 1,000m in flat areas down to 400m in steep terrain. Side-scan mosaics were generated with a 1m resolution. Selected areas were targeted by the higher resolution 410 kHz transmitter as well as by bottom photographs flying as low as a few meters above the seabed. The vehicles navigated autonomously using a combination of inertial navigation (Kearfott T-24 or T-16 INS) and long baseline acoustic navigation by computing their range to two moored acoustic transponders. Working efficiently in this rough topography at speeds above 3 knots was only possible due to the obstacle avoidance capabilities of these AUVs.

Jan 1, 2011

By Christina Pomee, John Parianos

"TOML’s ISA Contract comprises six areas (A-F) that span from 118° to 152° W and from 7° to 15° N or over 70% of the CCZ.During a 2015 exploration cruise, TOML scientists found that the a logging system developed by ISA (2010) was able to be adapted and enhanced, to describe in some detail the varied morphology of nodules both within the TOML areas and between them.The shapes and sizes of nodules seen were then found to relate to substrate type and setting, and thus likely thickness and long-term stability of the geochemically active layer. Consideration of the various processes that might influence growth helps constrain nodule formation further. The nodules effectively record the long-term geochemical conditions that lead to their formation.ISA (International Seabed Authority), 2010. A Geological Model of Polymetallic Nodule Deposits in the Clarion-Clipperton Fracture Zone and Prospector’s Guide for Polymetallic Nodule Deposits in the Clarion-Clipperton Fracture Zone. International Seabed Authority Technical Study: No. 6 ISBN: 978-976-95268-2-2"

Jan 1, 2017

By David S. Cronan

Submarine hydrothermal mineralization occurs in at least three locations along the Hellenic Volcanic Arc in the Eastern Mediterranean Sea. Weak hydrothermal discharges occur off Kos and Nisseros at the eastern end of the arc and off Milos at the western end. In both cases the hydrothermal solutions are rich in iron and manganese and are precipitating iron oxides variably enriched in minor elements. This points to the likely presence of sulphide minerals at shallow depth below the sea floor at these locations. By contrast, at Santorini, in the centre of the arc, the hydrothermal discharges are much stronger and rate of deposition of the hydrothermal minerals much greater. Indeed, in one of the two hydrothermally active embayments off Santorini (Nea Kameni) hydrothermal deposits are accumulating up to five times as fast as in the Atlantis II Deep of the Red Sea. Radiocarbon dating indicates that these deposits have been accumulating for about 100 years. In the other embayment off Santorini (Palaea Kameni), hydrothermal deposition has taken place over a longer period (more than 1,000 years) but the deposits are not so hydrothermally enriched due to the simultaneous deposition of biogenic silica and detrital mineral with the hydrothermal deposits. The observed pattern of increasing intensity of submarine hydrother¬mal activity from the extremities of the arc towards its centre argues for additional hydrothermal mineralization on poorly explored areas of the sea floor between Milos and Santorini and between Kos and Santorini.

Jan 1, 1994

By James E. Dailey

Marine mining is driven by profitability, and profitability is driven in turn by people and equipment that can work productively and safely at sea. Design challenges faced by the marine mining community have much in common with those faced by the offshore construction community. Technical solutions continue to move freely between both communities. A brief pictorial history summarizes the evolution of offshore construction technology as it grew in the Gulf of Mexico and expanded worldwide. Attention is focused on those areas of platform and pipeline construcion where there is potential technology application to underwater mining. An especially difficult challenge faced by both communities is work in the surf zone. Some innovative concepts for surf zone construction operations are presented and possible applications to marine mining are suggested.

Jan 1, 1989

By Elizabeth McIsaac, Wylie Spicer

"In July 2016 the International Seabed Authority (the “ISA”) released a first working draft of its mineral exploitation regulations as well as the standard contract terms for mineral resources in the Area, for which stakeholder input was sought in late 2016. In January of 2017 the ISA released a discussion paper on environmental matters related to these draft regulations. The ISA is now in the process of further developing its draft exploitation regulations and standard contract terms to ensure that seabed mining is carried out in an environmentally sound way for the common benefit of mankind.As the regulator of the “Area”, the ISA can draw lessons from onshore mining regulators and offshore petroleum regulators for their experiences in legislative drafting to smoothly and safely oversee project development, implementation, and closure. However, one of the unique challenges that the ISA faces in regulating private industry is its status as an international organization and not a sovereign nation, which results in a significantly different legal relationship between the regulator and the regulated. The result is that the exploitation contract is the sole legal connection between the mining proponent and the regulator for the exploitation phrase of the project.Accordingly, in the regulatory development process, the ISA must carefully consider which rights and obligations are set out in the exploitation contract versus the regulations. This decision will dictate the flexibility the ISA will have to modernize the conduct required of mining proponents in response to changing best practices in the industry, technological progress, and advances in the understanding of the marine ecosystem. As the first working draft of the exploitation regulations sets out an initial contract period of twenty years, it is crucial for the ISA to carefully consider the rights, obligations, and procedures it agrees to in the exploitation contract, as unilateral amendment will not be possible after contract execution."

Jan 1, 2017

By Jonguk Kim

Submarine hydrothermal activity and mineralization related to island arc volcanism along the Tonga arc were explored during two research cruises in October 2009 (KODOS 09H) and February 2010 (KODOS 10H), respectively. In KODOS 09H cruise, geophysical survey, including multi-beam bathymetry, marine seismic and magnetic investigations, was performed on 10 volcanoes to find out possible structural discontinuity that can act as fluid pathway for formation of hydrothermal deposits at submarine caldera system. The result provided acoustic and seismic image maps and magnetic anomaly maps of targeted volcanoes. Then, detailed seafloor observation and sampling as well as deep tow side scan sonar survey were performed in KODOS 10H cruise on 5 volcanoes which are selected as targeted areas from the previous cruise. Among 5 targeted volcanoes, TA26 shows most extensive hydrothermal activity. Hydrothermal vents and alteration zone were observed on western caldera and summit of eastern cone of the TA26. Although only weak hydrothermal alteration was observed on eastern cone, mineralized fragments of chimney and mound were sampled from western wall of central caldera on TA25 volcano. On TA12 volcano, strong hydrothermal plume and alteration zone was detected during video tows operated between SW scoria cone and small ridge. However, only small amount of hydrothermal altered rocks were collected from TA12. Although hydrothermal activity and mineralization might be formed, supported by plume detection and result of geophysical survey, only weak alteration zones were observed on other two volcanoes (TA19 and TA22). The exploration area generally show shallow depth up to several tens of meters on summit where subsurface boiling of hydrothermal fluid might occur due to low hydraulic pressure, which can affect on styles of hydrothermal venting and mineralization process observed on Tonga submarine arc volcanoes.

Jan 1, 2010

By Yves Fouquet

Recent exploration demonstrates that hydrothermal systems related to upper mantle ultramafic outcrops are common in the modern ocean. Most sites are located on slow spreading ridges with a low magmatic budget. Volcanogenic Massive Sulfide (VMS) deposits, associated with basalt, along the Mid Atlantic Ridge (MAR) are volcanically controlled near the topographic highs at the center of the segments. Three preferential settings are identified for ultramafic sulfide mineralization: 1) Off axis, on rift valley walls, near the amagmatic ends of the segments; 2) Non-transform offsets and 3) Ultramafic dome structures at the ridge transform fault intersection. The upper surface of these domes is often interpreted as a detachment fault. Three processes are considered for driving hydrothermal cells in ultramafic rocks: 1) regional heat flow at the ridge axis 2) Cooling of a deep gabbroic intrusion and 3) exothermic heat produced during serpentinisation. Along the Mid Atlantic Ridge, four types of ultramafic hydrothermal mineralization are observed: 1) High temperature (>350°C) sulfide mineralization related to low pH fluids, (ex. The Logachev field at 14°45? N and the Rainbow field at 36°14 N); 2) Medium temperature carbonate chimneys (<100°C) related to high pH fluids (ex. The Lost City site at 30°N); 3) Low temperature diffuse venting associated with extremely high methane discharge and pervasive alteration and silicification of both volcanic and ultramafic rocks (ex : The Saldanha field at 36°34 N); 4) Stockwork mineralization and quartz veins with sulfides related to gabbroic intrusions within ultramafic rocks (15°N). When compared to mineralization in a basaltic environment, sulfide deposits are enriched in copper, zinc and specific elements related to an ultramafic rock source such as Ni and Co. They are also significantly enriched in gold which, unlike in basaltic environments, has a bimodal occurrence both in low temperature Zn-rich assemblages and in high temperature Cu-rich mineral assemblages. The Cu-Zn-Co-Au deposits along the Mid Atlantic Ridge seem to be more common than on land where few similar VMS deposits are known. We consider that ultramafic VMS deposits on slow spreading ridges constitute a specific marine type of mineralization that is less easily than back arc deposits, incorporated into the continent during obduction processes.

Jan 1, 2004

By Tracy Shimmield

Deep sea tailings placement (DSTP) techniques have been pioneered in Papua New Guinea (PNG): a mining reliant economy in a seismically active region, facing major environmental challenges in the safe handling and storage of mine tailings on land. Scientists at SAMS have researched impacts of DSTP on the marine environment specifically to inform and develop guidelines for the use of DSTP to reduce environmental impact, thereby lowering risk and increasing private sector investment. Guidelines have been established as regulation by the PNG Government providing reassurance to private investors, facilitating an increase in mining exports to 60% of total export. Researchers investigated the effects of DSTP at 2 PNG mines: Lihir Gold Mine which has been actively discharging tailings since 1996 and Misima Mine, closed in 2004 after discharging tailings for 15 years, allowing an assessment of the recovery of the marine environment after tailings placement. Research involved investigating ocean currents and mixing, the behaviour of metals and the effect of tailings on benthic communities including the risk of elevated metal contents entering the food chain. The research established a metal ?fingerprint? of tailings compared to natural sediments, which enabled the transport of fine tailings within the deep ocean to be ascertained.

Sep 14, 2011

By Peter M. Herzig

In 1994 and 1998 the German research vessel R/V Sonne undertook detailed mapping and sampling of the largely uncharted offshore areas of the Tabar-Lihir-Tanga-Feni island chain in the New Ireland Basin of Papua New Guinea. The New Ireland Basin occupies a fore-arc position with respect to the formerly active Manus-Kilinailau arc-trench system and hosts a series of Pliocene to Recent alkaline volcanoes which are built on rifted Miocene sedimentary basement. Several of the volcanoes possess high-level porphyry stocks and active geothermal systems, including gold-depositing hot springs and the giant (40 million ounces) Ladolam gold deposit on the island of Lihir. On the southern flank of Lihir island, a group of three volcanic cones were discovered at water depths from 1.000-1.500 m. The volcanoes are located in a narrow zone of recent seismic activity and elevated heat flow (up to 100 mW/m2). The recovered volcanic rocks consist of fresh alkali-olivine basalts, clinopyroxene-rich basalts (ankaramites), porphyritic phlogopite basalts, and trachybasalts. Unusual gold-rich hydrothermal precipitates were recovered from the summit of the 600 m high Conical Seamount located only about 10 km south of Lihir Island. 1200 kg of sampled material systematically collected with a TV-guided grab from the top plateau (150 x 200 m, 1.050 m water depth) are intensely mineralized with pyrite, marcasite, minor sphalerite, chalcopyrite, galena, tennantite/tetrahedrite, and orpiment/realgar together with traces of anglesite, cerrusite, and amorphous silica in stockwork-like veins. Bulk samples of the vein mineralization consist mainly of clays, silica, and disseminated sulfides, and have an unusual high gold content ranging from 1.2-44.0 ppm Au. In some of these samples, grains of native gold (about 1 micron in diameter) were identified by SEM in pyrite and sphalerite. The gold-rich material also contains high concentrations of silver (up to 1000 ppm) and typical epithermal elements such as As (2.6 wt.%), Sb (0.2 wt.%), and Hg (34 ppm). Similar to epithermal deposits on land, which usually have only low base metal contents, the samples from Conical Seamount contain only minor amounts of Zn (max. 4.5 wt.%), Cu (2.0 wt.%), and Pb (2.0 wt.%). Many of the samples recovered from Conical Seamount are virtually identical to the gold ore at Lihir.

Jan 1, 1998

By Mayumi Ito

Seafloor hydrothermal deposits are found worldwide at 700 to 3,600 meters below sea level [1] and contain base and precious metals like Cu, Pb, Zn, Au, and Ag. Some deposits were found in the Japanese exclusive economic zone and the commercial potential will depend on developments in mining and treatment costs of onshore mines. The ores require mineral processing to become concentrate for the various metal smelters and the authors are investigating mineral processing treatments of collected samples. The collected samples were classified into three components (chimney, mounds, and substrate rocks) and they were separated using a RETAC jig. The mound component contains zinc, lead, and copper minerals and further separation using flotation was investigated. This paper introduces results of the mineral processing tests using gravity separation and flotation.

Jan 1, 2011

By ?. V. Kabanov

n considered operation hydraulic and kinematic circuits of deep-water installation for sampling a ground from a sea-bottom are submitted. Control by setters is made remotely from a service station with the help of a system of telemechanics. Migration of apparatus along a bottom is ensured with the help of force of a response of a jet and Archimedean force. The mathematical exposition of the device composed and computer simulation is Design parameters are defined and static performances are obtained. Operation is in a stage of manufacture of working drawings. There are patents of Russia.

Jan 1, 2005

By Jiahua Pan, Yanxiong Mei, Shuqin Liu, Rongfu Pei

Growth characteristics of Co-rich crusts from the Western Pacific have been approached. The thick crust shows 3 structural layers: compact upper layer, porous middle layer, and compact lower layer. The middle and lower layers have obviously different microscopic structure, color, and luster. Preliminary study of Calcareous nanofossils in one crust shows that the crust began to grow since Paleogene. The porous middle layer was formed from late Miocene to late Pliocene (Ca. 0.5 ~ 11.9Ma) and the compact lower layer was formed from late Paleocene to late Oligocene (Ca. 56.3 ~ 23.2Ma). The sedimentary hiatus of a 14.26Ma was observed between the middle and lower layers. The boundary between them to be Oligocene/Miocene (O/M) shows an important message on growth age.

By Jeremy Spearman, Mark Lee, Jon Taylor, Neil Crossouard, Bramley Murton

"SUMMARYThis paper describes challenges faced when executing a programme of monitoring to measure the dynamics of currents and sediment plumes at a seamount and the solutions identified to deliver the measurements. The study site was the Tropic Seamount, which extends some 3300m above the surrounding seabed and is found at the southern limit of the Canary Island Seamount Province. The purpose of the study, which forms part of the Marine E-tech project, was to provide information on the interaction of flows with the seamount and to assess the behaviour of sediment plumes that could be generated from potential seabed mining operations targeting the recovery of ferromanganese crusts. Since the crest of the seamount is submerged to a depth of 1000m, much of the work was undertaken using remotely operated and autonomous vehicles supported by measurements from the surface vessel. Despite only limited information on currents being available for planning purposes, the combination of short term forecasting using a 3-dimesional hydrodynamic model of the study area coupled with the collection and analysis of reconnaissance data collected during the first phase of measurement activities made it possible to plan and execute a number of detailed hydrodynamic experiments on the seamount crest. The results of these experiments have advanced the understanding of the behaviour of sediment plumes in the deep ocean and will ultimately improve our ability to manage the impacts which may arise from deep sea mining operations."

Jan 1, 2017

By V. K. Banakar

The occurrence of hydrogenous ferromanganese encrustations (Fe-Mn crusts) on the Cretaceous age Afanasiy-Nikitin Seamounts (ANS) in the eastern Equatorial Indian Ocean (EEIO) was first reported by Banakar et al. (1997, Marine Geology). The major element composition of the samples from the upper flank of the ANS (~1650 m water depth) indicated enrichment of Co up to 0.9 % (Parthiban and Banakar, 1999, Indian Mineralogist). Subsequently a project supported by the Department of Ocean Development to explore the ANS for Co-enriched Fe-Mn crusts was launched in 2002 by the National Institute of Oceanography. Sampling at regular depth intervals along two transects on the slopes of the northern elevated region of the ANS was carried out. The Fe-Mn oxide deposition is evident on almost all types of substrates viz., basalts, conglomerate limestone, fossil corals etc., and the thickness of the oxide layer varies from a patina to 7 cm. The Fe-Mn crust growth is evident only above a water depth of 3200 m, below which semi-lithified carbonate ooze is dominant. The ANS Fe-Mn crusts from all the water depths exhibit Mn/Fe < 1.5 suggesting pure hydrogenetic accumulation of metal-hydroxides. Bulk sample Ce-contents for a few selected depth-representative samples are remarkably high, up to 3700 ppm with an average of ~2500 ppm. The positive Ce-anomaly decreases from ~8 at 1600 m depth to ~1.6 at 3200 m depth, which is in contrast to the modern dissolved oxygen depth-profile in the region. This observation suggests that major time-period of the Fe-Mn crust accretion history is dominated by ambient waters with lower-oxygen at deeper depths than at the intermediate depths. This in turn probably suggests a major reorganization in the deep-intermediate hydrography of the region in the past.

Jan 1, 2005

By Johnson R. Cann

Ocean floor sulfide deposits are now known from many parts of the world mid-ocean ridge system and from some seamounts. Clearly they can be expected to occur commonly on the ocean floor. However, only two or three of the known deposits appear to approach the million-ton size, and in none of the deposits has the grade been well-defined. Can knowledge of the processes that happen within the hydrothermal plumbing below deposits help define the conditions under which large, high-grade deposits form? Here I review present knowledge of ocean-floor hydrothermal processes to attempt a first answer to this question. There are three sources of information about these processes. The solutions emerging from active systems must be compatible with patterns of alteration that underlie the volcanogenic sulfide deposits of ophiolite complexes, which are slices of ocean crust thrust onto land. Both of these types of evidence can be linked by computer modelling of the exchange of heat and metals between rocks and flowing water.

Jan 1, 1988

By P. E. Halbach

On June 26, 1988, the Jade Hydrothermal Field was discovered in the Okinawa Trough by the German RV Sonne. This research cruise has taken place within the scope of a German-Japanese cooperative project. The Okinawa Trough, located between the Ryukyu Island Chain and the east coast of China, is an active backarc-basin formed by extension within the continental lithosphere. The Ryukyu arc consists of a nonvolcanic outer arc, forming the main island chain and representing compressive highs of the Asian continental margin, and an inner arc with present-day volcanism in its northern part (Sibuet et al. 1988). The valleys and ridges of the trough are cut across by transverse faults, giving rise to younger volcanic intrusions. The Jade Hydrothermal Field was detected in a caldera-like structure. It is. located at about 27°15,0&apos;N and 127°04,5&apos;E with a maxi- mum water depth of about 1650 m. Data of heat flow measurements show a high anomaly in the cauldron basin with values ranging from around 100 to 800 mw/m2 (Halbach et al. 1989). The hydrothermal vent area was discovered in the northern part of the inside northeast slope of the cauldron in a water depth between about 1300 and 1500 m. We identified different varieties of hydrothermal

Jan 1, 1989

By Masaomi Kurihara, Seiya Kawano, Norihiro Yamaji, Satoshi Shiokawa, Nobuyuki Okamoto, Hironobu Sakurai

Seafloor polymetallic sulphides are distributed in the EEZ of Japan, including substantial deposits in the Okinawa Trough and Izu-Bonin back-arc basin. In this new frontier, the successful development of these resources in Japan is expected to bring about a new domestic supply of mineral resources. The initial stages of this development are authorized by the Basic Plan on Ocean Policy, approved by the Japanese Cabinet on April 26, 2013, and the Plan for the Development of Marine Energy and Mineral Resources, formulated by the Ministry of Economy, Trade and Industry (METI) on December 24, 2013. In 2008, the Japan Oil, Gas and Metals National Corporation (JOGMEC), commissioned by METI, began a survey and technological development programme for the development of the seafloor polymetallc sulphides (PMS) based on these Plans. The examination of four different fields: the evaluation of the amount of the resource, environmental assessment, mining technology, and processing & smelting technology, are concurrently promoted, aiming for commercialization as soon as possible. Based on the results of research for properties of geomorphology and marine environments of the target test sites in the Okinawa trough, which have been ongoing for several years, the preparation of the pilot lifting test included an in-situ excavation and crushing test conducted using test excavating and crushing systems.

Jan 1, 2018

By Masaomi Kurihara, Seiya Kawano, Norihiro Yamajim, Satoshi Shiokawa, Nobuyuki Okamoto, Hironobu Sakurai

Seafloor polymetallic sulphides are distributed in the EEZ of Japan, including substantial deposits in the Okinawa Trough and Izu-Bonin back-arc basin. In this new frontier, the successful development of these resources in Japan is expected to bring about a new domestic supply of mineral resources. The initial stages of this development are authorized by the Basic Plan on Ocean Policy, approved by the Japanese Cabinet on April 26, 2013, and the Plan for the Development of Marine Energy and Mineral Resources, formulated by the Ministry of Economy, Trade and Industry (METI) on December 24, 2013. In 2008, the Japan Oil, Gas and Metals National Corporation (JOGMEC), commissioned by METI, began a survey and technological development programme for the development of the seafloor polymetallc sulphides (PMS) based on these Plans. The examination of four different fields: the evaluation of the amount of the resource, environmental assessment, mining technology, and processing & smelting technology, are concurrently promoted, aiming for commercialization as soon as possible. Based on the results of research for properties of geomorphology and marine environments of the target test sites in the Okinawa trough, which have been ongoing for several years, the preparation of the pilot lifting test included an in-situ excavation and crushing test conducted using test excavating and crushing systems.

Jan 1, 2018

By Raymond A. Binns

Exploration for high-value massive sulfide deposits on the ocean floor typically commences with a search for chimney fields in appropriate geological settings, followed by collection and assaying of standing chimneys. Individual chimney fields are generally too small in aggregate volume to constitute viable resources in their own right. Unless numerous small fields occur in reasonably close proximity, presence of plentiful sub-seafloor mineralization with acceptable metal tenor is the more likely requirement for potential exploitation. Expensive drilling is required to prove up mounds of collapsed chimneys, or dilatory sheets and veins or replacements of massive/semimassive sulfide (?stockworks? or ?manto?-like bodies) in underlying host rock. Where multiple targets have been defined, as many parameters as possible are desirable to help rank them for drilling.

Jan 1, 2011

By Ning Yang, Sup Hong

INTRODUCTION Metal components contained in deep-seabed mineral resources are being highlighted as “energy metals”, which are widely utilized in the entire fields of energy: harvesting and generation, storage and transportation, and saving. Those are mostly trace and rare metals, and rare earth elements as well: manganese, nickel, cobalt, copper, molybdenum, tellurium, selenium, platinum, etc. Toward low carbon society, for global sustainability, the role of metals and minerals is growing up in industries of energy and transportation [1]. In this context, the production and supply of energy metals from deep seafloor have to be approached also based on sustainable development. In deep-seabed mining activity, the sustainability is focused on potential impacts on ecosystems in benthic area and water column. The environmental impacts in deep-seabed mining are caused basically by intervention in benthic zones and transportation of materials. Those are, in particular, removal of benthic habitats, generation and dispersion of sediment plumes, surface transportation of seawater and sediment, tailing from mining vessel, sound and light noises, and chemical leakage, etc. This paper is aiming at fundamental guidance towards sustainable mining of polymetallic nodules.

Jan 1, 2018