Search Documents

By Karen Dawson

This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.

By Adel M. Hanna, Ibrahim M. Mashhour

"Collapsible soil is known as one of the difficult soils, which possesses considerable strength when it is dry and significantly reduced when inundated. In practice, in case of a thick layer, pile foundations are often used to penetrate the collapsible soil to firm soil/rock strata. Inundation of collapsible soil is accompanied by a large and sudden settlement, which may significantly increase the negative skin friction and accordingly the drag loads on the pile’s shaft. Inundation may take place from the running surface-water or raising the groundwater. In case of surface water, the amount of settlement varies, depending on the extent of the wetted zone and the degree of saturation in the soil, while rising groundwater will produce full saturation in the ground and accordingly larger settlement.In the literature, there is lack of reports dealing with the prediction of the drag load on piles in collapsible soils subjected to inundation. This is due to the complexity of modeling collapsible soil analytically. Alternatively; the results of a sophisticated experimental investigation may guide the researcher to develop a model to predict the drag load on these piles.This paper presents the results of a small-scale experimental investigation tailored to measure the soil collapse during inundation and the associated drag load on an endbearing pile’s shaft. Based on the results of the present investigation, the effect of the soil collapse potential and the pressure acting on the soil during inundation on negative skin friction is presented.INTRODUCTIONCollapsible soil is a metastable material, traditionally defined as unsaturated soils that experiences a radical rearrangement of particles and significant reduction of volume upon wetting with or without loading (Bara 1976; Houston et al., 1988). A wide range of soils fall into the category of collapsible soil, including naturally existing types of soils such as: Alluvial flood plains, mud flows, residual soils, colluvial deposits, fans, aeolian or wind-blow deposits sands and silts (loess), volcanic tuffs, gypsum, dispersive clays, loose cemented sands , sodium rich montmorillonite clays (Clemence and Finbarr 1981).Soil wetting and soil saturation may take place as a result of urbanization or natural causes, such as: groundwater level rise, landscape irrigation, broken water pipelines or sewer lines, poor surface drainage, groundwater recharge, cut/fill construction, and moisture increase due to capillary rise. The severity of the outcome depends heavily on the so called collapse potential of the soil, which depends mainly on; soil type, compaction effort, initial water content and stress level at soaking (Houston and Houston, 1997; Ayadat and Hanna, 2007)."

Jan 1, 2015

By Ambarish Ghosh, Subhaprasad Chakraborty

"Construction of basement floors has become necessary to meet the requirement of parking in office and residential complexes and in hospitals for radiotherapy treatment. Important projects coming up in Kolkata are mostly in closer proximity of residential buildings, office buildings and historical monuments. Sheet piling is mostly used as temporary shoring system during construction. Deep excavation in urban environment creates great problem related to construction induced vibration due to driving of sheet piles for basement, pile driving etc. which raises the chances of damage of adjacent buildings and nearby structures. Vibratory sheet-pile driving is the most common method of sheet pile installation. The knowledge of induced vibration due to this phenomenon is still very deficient. This paper presents the analysis of measured vibration data collected from different sites of Kolkata with varying soil profile. Typical two case studies of sheet pile and pile driving has been presented and the vibration values are analysed. The responses of the vibration are reported in terms of peak particle velocities (PPV). To evaluate the effects of vibration due to pile driving two aspects have been considered: the effect of the energy entering the ground from the pile and the effect of the soil condition.INTRODUCTIONIn urban areas infrastructure development projects are mainly located adjacent to existing structures like residential buildings, offices and historical structures. The construction work of such project influences the surrounding environment as well as human perception (Wiss 1981). During the construction of basement for residential complexes and hospitals sheet piling is mostly used as temporary shoring system or as to support the earth mass. The vibration induced due to driving of piles and sheet piles have been presented herein. Deep excavation projects close to existing structures increase the concern of environmental impact. For this reason the vibration assessment and prediction has become a subject of great interest. It is important to develop a site specific model for predicting the ground vibration resulting from pile and sheet pile driving at the construction sites. The developed model gives the efficacy to guide the engineer to select the construction methodology ensuring the safety of the surrounding structure. The model developed here is site specific and the parameters that has been used are dependent on the soil condition and the energy source."

Jan 1, 2015

By Aly M. Mohammad

Croton Point Avenue Bridge carries Croton Avenue over Metro-North main tracks at Harmon Rail Yard in Westchester County, New York. The new bridge is 1100 foot long and 36 foot wide nine span structure with three spans continuous units. The spans are steel multi-stringers, composite with concrete deck. The piers are solid wall piers and the foundations are spread footings. During the design of the bridge foundations it was determined that the relatively loose to medium dense sand layer is susceptible to liquefaction under a design earthquake with a seismic coefficient of 0.15g. Several foundation options were considered for the new bridge including both shallow and deep foundations. It was determined that the most cost effective alternative is to use spread footing foundations supported on densified soils. Vibratory probes were utilized to densify the loose to medium dense sand layer and reduce the risk of liquefaction. Densification test sections were performed to determine the optimum spacing for the vibro probes. The test sections included performing piezocone tests before and after the densification to compare the increase in relative density of the sand. In addition, ground surface settlement due to the vibro probes was measured and correlated to the increase of soil relative density. The paper will present the results of the ground improvement method utilized and correlate the spacing of the vibro probes and the increase in relative density and the results of the piezocone tests performed before and after the densification. It was found that the vibro probes are not as effective as thought at shallow depth below the ground surface. It is believed that the results and finding presented in this paper will benefit both the design and construction industries by providing a relatively cost effective means to improve the soils

Jan 1, 2007

By Hyung-Min Kwon

There are a number of methods available that can be used to estimate the bearing capacity of piles that are subject to lateral load, such as the theory of subgrade reaction or the elastic continuum approach. The objective of these approaches is to determine the lateral load corresponding to the allowable lateral displacement of the pile. It is important to select the appropriate soil stiffness when analyzing soil behavior within the allowable displacement of piles because the stiffness of soil is dependent on the displacement of piles. Even though pressuremeter tests can measure the stress-strain behavior within a wide strain range, pressuremeter test results have been utilized to assess only the fragmentary soil modulus based on either semi-empirical correlations or analytical approaches. This study is concerned with a methodology that can estimate the horizontal deformational property, while taking into consideration the nonlinear deformational characteristics of sandy soils. Pressuremeter tests were conducted for 15 cases using a calibration chamber. Reloading curves were employed in the estimation of horizontal deformational property in order to minimize the effect of soil disturbance caused by the installation of the probe. The shear modulus degradation characteristics were estimated from the curve fitting for the reloading curve and from extrapolation using the exponential function. In addition, the difference was taken into account between the stress state around the probe in reloading and that of the in-situ state. A consistent relationship was observed between the maximum shear modulus taken from the suggested method and the bender element tests performed in the calibration chamber, simultaneously with the pressuremeter tests. In addition, the results showed significant concurrence with the well-known empirical correlation.

Jan 1, 2008

By Alan Christopherson

Nearshore construction projects often require installation of steel piles and specific methodologies of installing piles may adversely affect nearby species of concern. Water is an uncompressible medium which allows for easy transmission of energy through the water column. Energy transmission through water depends on the following factors for pile driving: 1) direct contact of the pile and the water; 2) the depth of the water column; 3) the size of the pile; 4) type of hammer; and 5) the energy of the hammer. Seasonal restrictions are usually the best practicable alternative for reducing habitat impacts when pile driving activities may adversely affect the species of concern. When seasonal restrictions are not practical other options need to be evaluated, including mitigation and noise attenuation devices. The broad array of mitigation options will not be discussed as part of this presentation but instead will focus on noise attenuation technologies. Dewatered cofferdams can be effective noise attenuators as they eliminate direct contact of the pile with water while driving. Also, introduction of a compressible medium, like air, near the energy source can provide sound energy attenuation. An unconfined bubble curtain is relatively inexpensive but is not effective in tidal marine projects or rivers and may have unacceptable secondary effects. Secondary effects must be evaluated as these can increase exponentially for larger projects. Secondary effects to the environment include air quality degradation from air compressor use, transportation costs for fuel and equipment, and the potential for injecting oily compressed air into the water column. The confined bubble curtain works well in nearly all environments. It usually is more expensive initially, relative to an unconfined air curtain, but there is less potential for harmful secondary effects. Generally, seasonal restrictions will be adequate to protect species of concern. However, there are conditions in which mitigation or one of the sound attenuation options should be utilized. Site specific factors, including the amount of energy being imparted into the environment, sensitivity of the species of concern, current, accessibility, length of time needed to complete the project, and the cost of the sound attenuation, should be factored into the permit evaluation.

Jan 1, 2013

By Fawad S. Niazi

Analysis of deep foundations in terms of axial capacity has been a topic of great interest in the soil-structure interaction problems. Soil behavior is governed by a series of complex stress-strain changes that occur during pile installation and subsequent loading. Owing to the difficulties and uncertainties on the basis of the soil strength-deformation characteristics, one of the most frequently followed design practice is to refer to the formulae correlating directly the pile axial capacity components of unit base resistance (qb) and unit shaft resistance (fp) to the data collected from cone penetration test (CPT), i.e. to the tip stress (qc or more proper qt), sleeve friction (fs), and shoulder pore water pressure (u2). The elementary basis for such formulations has been the idea of considering cone penetrometer as a mini-pile foundation. This has resulted in plethora of correlative relationships in the past over 60 years. Such correlations, although empirical, have been worked out on the basis of load test results from both instrumented and un-instrumented full scale piles and are able to accommodate many important variables. A quick review of the evolution process and development of such design formulations is presented with a view to propose recommendations for future research directions, where the latest version of CPT i.e. seismic piezocone test (SCPTu) can be used to advance from capacitysingularity to the complete axial pile load–displacement (Q–w) response.

Jan 1, 2013

By Franz-Werner Gerressen

In the changing construction environment clients are searching for new technology to complete their projects in shorter times. Manufacturers are therefore developing solutions to speed up established construction methods. The significant progress in recent years with the development of increasingly powerful drilling rigs is providing piling companies increase options for the execution of specialist foundation projects. The double rotary drilling methods are primarily used for the construction of pile walls as support for deep excavations. Typically these retaining walls are designed and installed as cased piles using the established Kelly drilling mode. However, more recently it is more popular to undertake these projects with the Cased Continuous Flight Auger (CCFA) system. This paper provides an overview of drilling with double rotary methods, in particular the monitoring during installation.

Jan 1, 2009

By Massimo Poggio, Gabriele Balconi, Andrea M. R. Pettinaroli, Mario Ruggiero, Riccardo Castellanza

Grouting technologies are ground treatment techniques used for modifying the behaviour of a mass of soil or rock by injecting a mixture. The sleeved port pipes (also called Tube A Manchette) are highly diffused for grouting treatment of coarse soils and fissured rocks. This paper describes a combination of jet grouting and rock grouting with MPSP (multiple packer sleeve pipe) technique that has been used to realize waterproof curtains under fluvial structures for a cascade hydro-power plant. This is composed by five mini hydro-power plants, placed along the Iskar River, in Bulgaria, and composed by a penstock followed by the power house, a spillway, and an earth dam containing the reservoir. The geology of the site is characterized by an upper alluvial deposit lying over the bedrock. In each site, similar treatments were carried out: an impervious curtain along the plant section, obtained by executing jet-grouting columns in the surficial alluvial layers and grouting the underlying fractured rock by means of port pipes. The temporary embankment, built during the works for protecting each site from the possible river floods, has been waterproofed and stabilized by reinforced jet-grouting columns. The grouting processes have been controlled and monitored by a computerized system. INTRODUCTION The Iskar river cascade hydropower plant is situated northern of Sofia, Bulgaria, and it is composed by nine plants. Actually five of them have been built and produce energy. Each plant is composed by a penstock followed by the turbine building, a spillway, and an earth dam that contains the reservoir. The Iskar rivers runs in a narrow valley characterized by diorite or diabase rocks, with an upper deposit of alluvial soil, composed mainly by gravel and sand. Each plant requires an impervious curtain under the structures and in correspondence of the earth dam: this has been obtained by means of a jet grouting treatment of the alluvial coarse soil, and a grouting treatment with cement mixtures of the underlying rock using the MPSP technology. During the construction of the structures, the site has been shielded from the river water by a temporary earth embankment that has been statically improved and waterproofed by jet grouting columns reinforced with steel tubes; this allowed to work without interruption even in case of flood of the Iskar river.

Jan 1, 2019

By Nabil F. Ismael, Mohamed El Deeb

"The behavior of laterally loaded step tapered bored piles in calcareous sand was examined by field tests. Lateral load tests were carried out on straight and step tapered bored piles 5.3 m long embedded 5 m below ground level. All piles were installed by augering. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles have a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads. Test results indicate non linear response and substantial increase in lateral capacity and decrease of deflection for the step tapered piles compared with the 0.2 m diameter straight shaft piles. However, beyond a depth of 40% of the pile length, the strengthening of the pile section by enlargement of its diameter had little effect on the lateral capacity and the deflection of step tapered bored piles.IntroductionFor many structures on pile foundations the ultimate capacity under lateral loads is important and may be the controlling factor in foundation design. Examples include transmission tower foundations and fender piles at sea port facilities. Increasing loads on these structures has resulted in piles of large diameter and depth at a significantly higher cost.In this work, the use of step tapered bored piles with a larger diameter along the upper segment of the piles is examined by field testing and analysis on single piles in calcareous desert sands. Lateral load tests were carried out on straight and step tapered piles 5.3 m long embedded 5 m below ground level. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles had a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads for step tapered bored piles."

Jan 1, 2005

By Hamed Ardalan, Mohamed Ashour

"CHAPTER 1INTRODUCTIONThe use of piles to stabilize active landslides or to prevent instability in currently stable slopes has become one of the most important innovative slope reinforcement techniques over the last few decades. Piles have been used successfully in many situations in order to stabilize slopes or to improve slope stability, and numerous methods have been developed for the analysis of piled slopes (Ito et al., 1981; Poulos, 1995; Chen and Poulos, 1997; Zeng and Liang, 2002; Won et al., 2005).The piles used in slope stabilization are usually subjected to lateral force through horizontal movements of the surrounding soil; hence they are considered to be passive piles. The interaction behavior between the piles and the soil is a complicated phenomenon due to its 3-dimensional nature and can be influenced by many factors, such as the characteristics of deformation and the strength parameters of both the pile and the soil. The interaction among piles installed in a slope is complex and depends on the pile and soil strength and stiffness properties, the length of the pile that is embedded in unstable (sliding) and stable soil layers, and the center-to-center pile spacing (S) in a row. Furthermore, the earth pressures applied to the piles are highly dependent upon the relative movement of the soil and the piles."

Jan 1, 2013

By William M. Camp

Construction-induced earthborn vibrations have long been recognized as a potential problem with respect to the constructed environment and various vibration criteria are in use to prevent damage. A special case of construction vibration control is the protection of early-age or ?green? concrete. Unlike limits for damage prevention to building stock, there is no rational, widely accepted limit for protection of early-age concrete. Numerous criteria have been proposed or reported in the literature and the most relevant and rational proposals are summarized herein. These findings are applied to a case history involving both bored and driven piles. Vibration measurements were made during pile driving activities and the vibration magnitude was evaluated with respect to the exposure of freshly-placed and curing concrete to the earthborn vibrations. The maximum vibration magnitude at the applicable distances from pile driving was on the order of 0.3 inches per second. Based on the most persuasive literature, threshold values of 0.8 inches per second or even 1 to 2 inches per second for the protection of green concrete appear to be well-supported. Consequently, it was concluded that the pile driving activities and bored pile construction could proceed simultaneously.

Jan 1, 2010

By Kamil Nuzha, Jianchao Li, Bashar S. Qubain

"The Philadelphia Water Department is rehabilitating Belmont Raw Water Basin. As part of this work, a 500-ft long, temporary cofferdam was designed to retain 35 ft of combined water and soil at the western half during the reconstruction of the eastern half. A cofferdam that comprises two integral rows of sheet piles was selected to take advantage of the soil’s weight between the sheet piles for increased stability. To fine tune the design, a geotechnical investigation was carried out to verify the subsurface conditions and, in particular, the top of rock variations along the centerline of the cofferdam. A detailed finite element analysis was performed based on the subsurface findings and incorporating the construction sequence to evaluate the behavior of the cofferdam at the following stages: installation of tie rods to connect to the two rows of sheet piles; partial excavation and installation of tiebacks; complete excavation of the east basin, and demolition of the cofferdam. Inclinometers and survey markers were installed every 100 ft along the cofferdam and were monitored throughout construction. The deformation measurements were in good agreement with the finite element results.INTRODUCTIONThe Philadelphia Water Department (PWD) Belmont Raw Water Basin is located at the intersection of City Line and Belmont Avenues in Philadelphia, PA. The facility actually contains two raw water basins, east and west, separated by an earthen dividing dike. Water leakage at the bottom of the basins and through the dividing dike together with increasing demand for a larger storage capacity dictated the replacement of the wide earthen dike with new narrower concrete structure. The temporary cofferdam was designed for a two-year period to facilitate excavation support, water cutoff, removal of the existing earthen dike and replacing it with a new concrete dike. During this construction sequence, the water level in the west basin had to be maintained at or near its full capacity.Various excavation support systems were considered for this project prior to the selection of a double wall sheet pile cofferdam. Fig. 1 shows a plan view of the cofferdam and the new dividing dike. A typical cross section of the two structures is shown in Fig. 2. Double row sheet pile walls are commonly used as both temporary and permanent retaining systems in open water applications such as construction works, quaywalls, breakwaters and revetments for storing industrial waste as indicated by Ohori, et al. (1984), Ohori et al. (1988), and Khan, et al. (2001). There are many advantages to double row sheet pile systems as recognized by Ohori, et al. (1984; 1988): (1) It can be installed and removed in the presence of water easily and quickly; (2) it provides stability with small width to height ratio, utilizing the existing soils between the installed sheet pile rows; and (3) it serves well as a means for water cutoff. These advantages meet the specific project requirements."

Jan 1, 2016

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees is applied to a 0.61 m flagpole and a 0.61m fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil is represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2011

By Ilhan Chang, Ernest Nsabimana, Kiseok Kwak, Juhyung Lee, Young-Hoon Jung

"Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.IntroductionWith the development of offshore technology, applications and real site installations of suction piles are increasing significantly nowadays. They are generally used as mooring anchors in various floating structures, marine platforms, and offshore wind turbines. According to its convenience in installation and removal, suction type foundations are becoming good alternatives for deep ocean support systems. The bearing capacity is similar to the bearing behavior of ordinary offshore structures (piles or drilled shafts). The most common use of suction caissons is anchors for catenary mooring lines, where the chain angle at the mudline is close to zero (Randolph, 2002; Sharma, 2004).Recently, it is reported that a huge isolated single suction pile can be replaced by a group of moderatesized suction piles (Randolph et al. 2004). A single monopile is easy to be produced and installed in site. It is expected that monopile foundation is not applicable for deep depths because it has a limitation on penetration according to its huge side skin area (i.e. friction). Moreover, stiffness requirements sometimes render thicker pile wall conditions which are impractical to be produced."

Jan 1, 2017

By A. Tejchman

On the site of building of a new flyover founded on piles the comprehensive "in situ" investigations were carried out. The subsoil conditions under each of 15 supports were very differentiated. Using of the static sounding results a new method for evaluation of bearing capacity and settlement of piles was proposed. The method is based on a special construction of the curve of load-settlement relationship. The verification of this method was made on the basis of loading of piles.

Jan 1, 2010

By Dimitrios C. Konstantakos

Cofferdam excavations have traditionally been designed with classical design methods that involve direct computations of active or apparent earth pressures. However in contrast to finite element methods, traditional analyses can not account for full soil-structure interaction. Because of their complexity, numerical analyses are performed almost exclusively by computers. Recent theoretical and computer advancements have made the use of the finite element method much more user-friendly and affordable. General information about the basics of the finite element method in geotechnical engineering and for cofferdam excavations is presented. While knowledge of all intricate theoretical and computational details is not needed, the designer should at a minimum be aware of the most important aspects of soil modeling. Most importantly, the designer must have sufficient experience to be able to judge the relative ?correctness? of vast numerical results produced by today?s software programs. Hence, the human factor is an irreplaceable component of finite element computations.

Jan 1, 2013

By Ahmed H. Bukhary, Naser A. Al-Shayea

The objective is to assess the overconservatism in the parameters used for designing offshore piles. Methodology includes analysis of shaft friction data obtained from more than five different locations in the Arabian Gulf, consisting of 40 piles to depths up to 86 m. Reports were collected for both the dynamic pile monitoring system (DMS) and their corresponding geotechnical reports based on the American Petroleum Institute (API). The values of shaft capacity for the sand layers were analysed by comparing those based on API to the corresponding DMS values. Results of the comparison of the data from these reports showed that the pile design parameters obtained using API guidelines is generally smaller than that measured by DMS. The difference is presented in terms of an overconservative factor (OCF) which is adjusted based on statistical nonparametric test performed on the two data sets. The adjusted OCF were found to be 1.79 and 2.00 for carbonate sand at (loose to medium dense) and (dense to very dense) conditions, respectively. The corresponding values for silica sand were only 1.2 and 1.06. In conclusion, based on the evaluation conducted for data from these reports, the API shaft friction is overconservative for carbonate sand. The API shaft friction for piles in sand can be increased by multiplying it by the adjusted OCF.

By Abdelmalek Bouazza, Aamir Mahawish, Will P. Gates

Bio-grouting by means of microbial induced calcite (calcium carbonate) precipitation (MICP) to improve mechanical properties of granular soils has gained much attention in recent years. The biogrouting process offers an alternative and environmentally friendly approach to conventional soil improvement techniques, such as cement. Bio-grouting by urea hydrolysis has been extensively applied to tackle various geotechnical problems. However, it has yet to be applied to improve engineering properties (compressive strength) of a coarse cohesionless material with the aim using it as sand/stone columns within soft and very soft soils. This paper investigates the effect of using light, moderate and heavy biochemical treatments on the unconfined compressive strength (UCS) of coarse sand columns. In addition, the microstructure of the bio-cemented coarse material has been analysed by X-ray computed tomography (XRCT). The experimental results revealed that the UCS could reach up to 200kPa, 1000kPa and 5500kPa for light, moderate and heavy bio-cemented coarse sand columns, respectively. The microstructure investigations showed that the deposited calcium carbonate can be identified using XRCT imaging and can be associated with the gain in UCS values. Various microstructure properties, such as void ratio, dry density and porosity were also identified and compared with the laboratory data.

Jan 1, 1900

By Michael D. Justason

This paper describes the technology behind the development of an automated energy control system for a diesel pile hammer. Some background is given on experience using an energy monitoring system on the Route 1/I-95 interchange in Alexandria, Virginia. An adjustable hammer throttle and feedback from an energy monitoring system was then used to create a fully automated hammer energy control system. The performance of this system is described in reference to a piling project in Canada where the automated energy control system was used to obtain an unprecedented level of quality control and assurance ? data and graphs from the project are presented. The hammer energy control system (ECS) was used to successfully control and maintain a prescribed impact energy for the diesel hammer. This paper presents the first ever results from a truly automated diesel pile hammer and points to a new direction in quality control and assurance in pile driving.

Jan 1, 2006