Search Documents

By P Kumar, J Safarian

Understanding how ore interacts with flux particles at elevated temperatures to create molten slag is crucial since it governs the dynamics of a chemical reaction. This study explores the smelting behaviour of pre-reduced Nchwaning manganese ore when combined with lime, with the objective of examining the evolving interaction between pre-reduced ore particles and lime over time. The research sheds light on the interaction between solid and liquid and the phases that emerge during this process. To achieve this, a sessile drop furnace was employed to rapidly heat the materials positioned adjacent to each other on an alumina substrate and to observe the smelting process as it unfolded over time. This method allowed for the direct observation of the melting temperatures and the flux-ore reaction progression rate, and the potential disruptive events that might occur. By comparing the molten interfaces of the fluxed materials at various time intervals, this study provides insights into the relative rate of slag formation from the two materials. The results indicate that the main slag formation initiated at approximately 1400°C and continued to advance with time, with complete mixing occurring around 1500°C. The possible phases formed were identified using Scanning Electron Microscopy and modelled using Fact Sage thermodynamic software. In addition, the iron particles in the pre-reduced Mn ore were separated and settled from a rich MnO-containing slag. It was found that the separation of molten iron droplets from the slag depends on the rate of solid MnO particles dissolution into the adjacent slag phase.

Jun 19, 2024

By Burchell S, McGregor K

The process of design, measurement and review is essential if blasting is to continuously improve to meet the increasing productivity goals of most mining operations. To achieve continual improvements, many operators are turning to contractors to provide the necessary technology. Under this arrangement, the contractor becomes the supplier of a service rather than products and assumes some of the risks associated with blasting by guaranteeing the end result. If contractors are to obtain significant productivity improvements they must continuously improve every aspect of their business.

Jan 1, 1994

By R Shelton

The Big Wainihinihi River and tunnel are located on the western side of the Southern Alps of New Zealand within the active Alpine Fault zone, which marks the boundary between the Pacific and Australian Tectonic Plates. The tunnel was built over 100 years ago to supply water for gold mining, but it now conveys water from a high-energy intake to a canal that supplies three of TrustPower’s hydro-electric power stations with a combined installed generating capacity of 10 MW. Part of the tunnel passes through an unstable 50° schist slope, which fi rst suffered a wedge failure in the 1929 Arthur’s Pass Earthquake and was reinstated in the mid-1970s for hydro generation. In 2008, TrustPower’s monitoring system showed that the wedge failure had remobilised and that urgent remediation was required.Harker Underground Construction (Harker) was awarded a design-build contract to restore the tunnel to service by tunnelling a new central section. Their geotechnical engineers, Peters and Cheung, reviewed the tunnel’s stability and proposed a new, safer tunnel alignment, deep behind the failure wedges. This work was based on their failure model, cost-benefit studies, and engineering geology completion mapping at the time of re-opening.Construction innovation was an important factor in ensuring the project’s success, as were detailed geological and geotechnical information, a robust methodology, strong client relationship and planning. To suit the varying rock conditions and restricted space, Harker combined a traditional drill-and-blast method with light-weight modular steel sets and timber supports to reduce construction costs and mitigate support risk. To make material handing easier in the tight conditions, a special electric locomotive was designed and built and blasting confi gurations were adapted to suit varying rock conditions in the highly fractured schist.The isolated site meant interesting and unexpected challenges, particularly communications and resources (both human and material). Despite that, the project was completed within budget, on schedule, and with no lost-time injuries.

Mar 8, 2011

By C Bartle

In many operations the use of less electrochemically reactive grinding media in the first grinding stage (for example, rod milling and high aspect ratio SAG milling) is rarely considered. Therefore, in reality a plant may inadvertently be using a 'mixed' media charge. That is, whilst employing inert grinding media during secondary grinding, electrochemically active forged steel grinding media may be used in the primary grinding stage. This paper discusses the impact of such a circuit on the pulp chemistry and flotation response of a refractory gold ore. The Wiluna concentrator has two grinding circuits operating in parallel. Line 1 operates a single ball mill in closed circuit with cyclones, and utilises high chrome grinding media, while the second circuit (Line 2) consists of a rod mill (with forged steel rods) in series with a ball mill, which also utilises high chrome grinding media. The cyclone overflows from both circuits are combined to feed a sulfide flotation circuit. Pulp chemistry surveys were completed around both grinding circuits, and laboratory flotation tests were conducted on the cyclone overflows. The results demonstrate clearly that the rod mill/ball mill circuit operated at significantly lower Eh and dissolved oxygen values, while the percentage EDTA extractable iron was considerably higher, when compared to the single stage ball milling circuit. These variations in pulp chemistry had a marked negative impact on the laboratory rougher flotation response, and suggests that plant performance may be affected.

Jan 1, 2008

The current drill-and-blast method of tunnelling is cyclic and, for this reason above all others, has a future application potential which is lower than that of continuous methods. There is scope for progress in several facets of today's drill-and-blast tunnelling. But even if each of its unit operations and the synthesis of these were to be optimised, this conventional method will, in the long term, fail to be a serious competitor for tunnelboring machines (TBMs), roadheaders and the like. If its role in tunnelling is not to decline at an increasing rate, drill-and-blast will need to be transformed into a continuous system. Boring and cutting machines consume considerable energy (and expenditure) in creating rock fragments which are smaller than those required by muck-handling equipment. In this respect, blasting is more efficient. Mechanical methods are also less versatile and flexible and, when planning proceeds on a basis of meagre or inadequate geological data, cannot be costed as accurately. Currently, research gains for TBMs and roadheaders are greater than those for conventional tunnelling. If (as is likely) the disadvantages of mechanical methods continue to be reduced at a greater rate, the swing away from drilling and blasting will gain momentum.

Jan 1, 1987

By W F. E Ouedraogo

This study data has been collected on a three-month period from November 2020 to January 2021 and based on three different pits: Vindaloo Main, Vindaloo Central and Bouere. Both pits having specific geotechnical and geological properties. Vindaloo Main, VIM, and Central, VIC, have the same mineral composition as volcanic tuff with felsic intrusion or monzodiorite, both rock mass is fractured with small joint. Geotechnically the uniaxial compressive strength UCS between 200 to 300 Mpa, Young’s Modulus 110 Gpa and Poisson’s ratio between 0.1 to 0.2. Bouere pit is basically made of volcanic tuff stock works as intrusive, UCS between 200 to 300 Mpa, Young’s Modulus 103 Gpa and Poisson’s ratio between 0.2 to 0.3. The first step of this study was to collect various data from mining operations around the drilling and blasting inputs. This was based around the different scenario of drilling parameters and the outcomes on the blasting, and how they impact load and haul operations and productivities of excavators from the heave to the last flitch. In most cases surface photos of the blast do not represent the overall fragmentation in the blast volume. Photos of the different flitches will not show only the effect of blast, as the loading operation generating more fragmentation by applying weight on the muck pile. Then the record of the different material uses for feeding. The last part of the analysis is the physical data from process plant such as particle size, throughput rate, both for the crusher and the mill, per pit and material and the specific Bond Work index (BWI). Fine particle quantity production is also a key point as is one direct indicator of milling performance. In overall, making link to BWI can influence at each stage of the mining to the processing operation. Drill and blast constitute a high cost in hard rock mining and trying to reduce these costs without an overview of all the integrated processes and context could end up by cost relocating to other activities in the process. However, the cost associated to size reduction builds exponentially as the particle size becomes smaller.

Jun 22, 2022

By M McGrory, A Rodolfo, J Paredes, L E. Manguba, K A Villaspir, G Webb, R Setiagani, H Cardenas

"OceanaGold’s Didipio operation has been in operation for three years. Integral to the flow sheet design is a flash flotation circuit treating a portion of cyclone underflow, consisting of an Outotec SK-500 flash rougher and an Outotec TC10 flash cleaner and a SB-2500 falcon treating flash rougher concentrate to recover fine free gold.Flash copper recovery has been holding steady at 60 per cent, while flash gold recovery at 50 per cent. Gold recovery from the gravity circuit is 22 per cent, bringing the overall flash plus gravity gold recovery to 72 per cent.Operation of the flash rougher is mainly by pulp level control. Control of copper grade in the flash cleaner is mainly controlled by air inflow and flash cleaner pulp level control drives copper recovery. Gold recovery around the circuit is mainly driven by gold head grade.SB-2500 concentrate is scalped with a 250 micron screen with the coarse fraction reporting to a SB-250 falcon, concentrate of which combines with the screen fine fraction to a Gemini table.Citation:Cardenas, H, McGrory, M, Webb, G, Paredes, J, Setiagani, R, Villaspir, K A, Manguba, L E and Rodolfo, A, 2016. Didipio Flash Flotation and Gravity Recovery Circuit, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 123–126 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S Maryati

Surface mining activities disturb large areas, produce great sediment loads and tend to be a source of water pollution if they are not managed properly. Coal mining in Indonesia has a very high risk of soil erosion because the coal mining areas are generally located in tropical areas with a high average of rainfall (4000 - 6000 mm/year) and use surface mining methods. The main factors affecting erosion risk are climate, soil type, topography, vegetation cover and management factors. Thus, the monitoring of erosion risk in mining areas is very important due to the characteristics of coal mining in Indonesia. The objective of this research is to determine the ability of satellite images (remote sensing data) and geographic information systems (GIS) to provide an accurate and up to date spatial database for the monitoring of erosion risk in surface coal mining areas using the Universal Soil Loss Equation (USLE) method.The erosion risk analysis and spatial data processing are generated by the ArcGIS 9.3 software and need several data, namely: an erosivity map, erodibility map, a slope map, vegetation index map and land management or land cover map. The erosivity map is derived from the rainfall data, whereas the erodibility map is derived from the soil map. The slope map is derived from the SRTM-DEM (Shuttle Radar Topography Mission-Digital Elevation Model) and processed using 3D analyst tools. Furthermore, the vegetation index map and land cover map are derived from a satellite image using digital image processing techniques.This preliminary study produced results that show soil erosion monitoring, which is integrated with remote sensing and GIS technologies, has great potential for producing accurate, advance, and low cost erosion risk maps in coal mining areas. This map is very important for getting spatial distributions of the erosion and useful for developing erosion management plans.

Nov 22, 2011

FIRST TOWN PLANNING PROPOSALS Initially, accommodation at the minesite was provided at the Pastoral Homestead situated some seven kilometres north-east of the mine and between 1963 and 1966 was the base of the exploration camp. Tents were used for sleeping of 100 men and the Homestead used for dining and office facilities. With the beginning of ore production and shipment due to commence in 1969 a permanent town location was sought. Early town planning studies had been commissioned by Amax Inc. and Colonial Sugar Refining Co. Ltd. and in 1967 The Broken Hill Proprietary Company Ltd. took over the responsibility for putting them into effect. The location chosen was about four kilometres due east of the mine. Certain dominant factors influenced this choice. It was near enough to the mine to share services, yet far enough away not to be affected by dust and noise and received the additional shelter of a range of hills separating it from the mine. A predominant slope to the east provided good drainage and the ground was easy to excavate for services.

Jan 1, 1976

By W A. Peppin, D N. Riley, N W. Schulenburg

In June 2008, a joint airborne collection using hyperpspectral systems was tested on a single Twin Otter aircraft. This experiment was designed to incorporate two airborne hyperspectral sensors for geological and environmental projects. Mineral exploration and environmental impact statements are two areas where full spectrum hyperspectral data can document the mineralogy at the surface prior to mining operations. Many previous hyperspectral remote sensing collections were collected on a single aircraft with a single sensor. Mineral mapping using hyperspectral sensors that measure in complimentary regions of the electromagnetic spectrum is cost effective as it allows for the mapping of clays, sulfates, carbonates, feldspars, quartz, garnets and many other minerals. This report describes the experiment using the following two hyperspectral sensors: ProspecTIR, a visible near and shortwave infrared (VNIR-SWIR) sensor with 356 channels and spectral range of 0.4 to 2.5 ¦m, along with a spatially enhanced broadband array spectrograph system (SEBASS), a midwave and longwave infrared (MWIR-LWIR) sensor with 128 channels from 2.5 to 5.3 ¦m and 128 channels from 7.6 to 13.5 ¦m. SpecTIRÆs ProspecTIR system and The Aerospace CorporationÆs Spatially Enhanced Broadband Array Spectrograph System (SEBASS) are pushbroom sensors, have high signal to noise ratios, have similar swath widths and instantaneous fields of view. Examples of data collection experiment will be shown with a focus on mineral/lithologic identification and mapping along with environmental assessment in the western United States. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

It is a well known fact that the best method of rock reinforcement is to avoid physical ground support. This goal can be achieved by means of: - Increasing the rock structural strength - Geological definition and forecasting. - Sequencing the excavation - Smooth blasting In many cases however, extra ground support is needed in order to maintain safe working conditions. In an open pit, the structural strength of rock cannot be increased by lowering the pit walls due to economical reasons. Economy demands steeper walls and less waste to be hauled to the dump. The geological conditions can also often be extremely poor and unpredictable. For excavation sequencing and smooth blasting there are good possi- bilities, such as cleaning of the pit walls after the main excavation, arul- ing of long small diameter straight inclined holes, use of smooth blasting techniques and lightened explosives.

Jan 1, 1989

By J Hadjigeorgiou, T R. Stacey

A ground support system is a combination of individual reinforcement and surface support elements that work together to retain and contain the rock mass. The various elements are subjected to external loads and to interactive loading between individual ground support system components. This paper focuses on the challenges in determining the capacity and behaviour of mesh, recognizing that installed mesh can be subjected to several loading mechanisms. Field observations from underground hard rock mines demonstrate that there are multiple types of damage and modes of failure of mesh. However, these are difficult to reproduce in a laboratory environment. A critical review has shown that existing mesh laboratory testing rigs reproduce very limited loading conditions that may not be representative of underground conditions. This has significant implications in quantifying and extrapolating the performance of mesh to ground conditions. CITATION:Hadjigeorgiou, J and Stacey, T R, 2018. Challenges in determining the capacity of mesh, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 280–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By D T. Ribeiro, J F. C L Costa, J C. Koppe

Drilling and sampling are responsible for most of the costs during mineral exploration, especially in multi-elements and polymetallic deposits, such as iron, manganese and bauxite deposits. On these deposits, often it is necessary to estimate multiple attributes at several granulometric fractions, ie distinct particle sizes. This paper investigates the effect of sampling at a close spacing grid only the head grades for the multiple chemical species in iron ore deposits. The remaining required data at the various grain sizes are sampled at a sparse grid. The derived geological model is checked for precision and accuracy comparing the output obtained against a model obtained using a complete isotopic data set including head grades and chemical analysis at each granulometric fraction analysed at all sampled positions. Among the several tested alternatives, the best procedure for dealing with the posed problem involved utilising the correlation coefficients between the grades at distinct fractions to obtain an isotopic database prior to interpolation. Cokriging was the method used, based on the intrinsic coregionalisation model. Estimates were obtained with the quality needed for the proposal of the study. Results showed that at least 50 per cent of the blocks were estimated with errors less than ten per cent relative to the grades obtained at the reference model, using only 15 per cent of the granulochemical data employed to obtain the reference model. The methodology also preserved the correlations between the attributes in their several granulometric fractions on the estimated model.

Sep 26, 2011

By R M. Yanamandra, M Kumar, S K. Tripathy, N Mangadoddy, P Sudikondala

Spiral concentrators are one of the flowing film gravity concentration devices used to beneficiate coal and mineral ores. The aim of the current study is to understand the particulate flow and separation performance of an LD9 spiral concentrator using a multi-phase Computational Fluid Dynamics (CFD) model. The CFD model utilises the Algebraic slip mixture model to simulate particulate flows. The model employs the Renormalisation group (RNG) k-ɛ turbulence models to resolve the fluid turbulence. Initially, the volume of fluid method was adopted to track the water-air interface. Simulations were then carried out at low (0.3 and 3 wt.%) and moderate (15 wt.%) solids concentrations. Multiple particle-phase representing particles of poly sizes (75–1400 µm) and multi-densities (1450–2650 kg/m3 ) were simulated to study the particle segregation on the spiral trough surface. The numerical predictions are compared with the literature performance data at a diluted pulp flow rate of 6 m3 /hr. The results were found in close agreement. Further, the same CFD model is used to study the change in pulp velocity, streamflow rates, and separation performance at increasing solids concentration. For the same density particles, Fine particles mostly show higher volume concentration in the middle and outer trough regions, whereas coarse particles show higher volume concentration in the interior and central trough regions. It implies that the fine particles mostly segregate towards the outer region, and dense particles segregate towards the axial column.

Aug 24, 2022

By A B. Christie, R Barker

Recent studies carried out to support the development of a strategy for the New Zealand mineral industry by the NZ Minerals Industry Association have included investigations of mineral potential, and the development of scenarios for realising this countryÆs mineral potential by 2010. New economic research is applying a general equilibrium model to quantify the opportunity cost of this potential. The model analyses separately four categories of land (private land and three categories of Crown land) and identifies four distinct mineral classes û precious metals, industrial minerals, coal and aggregate. It investigates the economic effect of the increased availability of mineral resources on the mining industry itself, on other industry sectors and on the NZ economy generally, including its impact on unemployment, GDP and household welfare.The analyses suggest that increases in the level of GDP of between 1.9 per cent and 3.4 per cent may be obtained by utilising New ZealandÆs mineral wealth to varying degrees. The mineral industry sectors are significant beneficiaries under all scenarios; mineral output increases by between two and five times its current level. However, the flow-on effects to the rest of the economy, and to households, are also significant. The analyses show that household income, adjusted for changes in consumer prices, can be expected to increase by between 1.6 per cent and 2.7 per cent. This results largely from increased employment.

Jan 1, 2002

By Saghafi A, Kelly M, Williams R. J

A two year program of research into the feasibility of long-hole drilling for improved gas emission control has been undertaken at Appin Colliery. State of the art equipment was employed involving cableless electronic surveying and down-hole motor drilling. The project involved the drilling of 1000 m long, in-seam boreholes in the Bulli seam and boreholes of similar length drilled cross measure and then in-seam along the underlying Balgownie seam. A new concept for gas drainage was defined, employing long-holes for both predrainage and post drainage.

Jan 1, 1988

By K P. Crameri

The Beta Hunt orebody is situated on the south western limb of the Kambalda dome. It is one of the nickel occurrences in the area which fall into the category of æKambalda Style OrebodiesÆ. These orebodies are renowned as being continuous uniformly mineralised ribbons of nickel sulfide mineralisation. Interestingly, Beta Hunt does not conform to this notion of continuity and uniformity and is in fact highly irregular in its ore distribution due largely to the influence of post depositional structure. In an attempt to understand the ore distribution at delineation stage rather than development stage a detailed footwall topography model is created using all available drilling data. To augment this drilling data, the routine use of downhole EM and borehole radar has been introduced to provide data beyond the confines of the drill core to enhance the geological interpretation of the footwall topography and the distribution of the mineralisation. The implementation of a detailed footwall model and the use of downhole geophysics has proved to be very effective in resolving the orebody complexity issues. Ongoing development of the methods used will continue to refine the interpretation of the geology to enable more efficient extraction of the orebody.

Jan 1, 2006

The Bellambi Coal Company Limited com menced longwall mining at South Bulli Colliery in 1965. At present it operates three long- wall units in two seams. Although results to date have been less successful than planned, it is apparent that this type of mining has tremendous potential in the particular conditions at South Bulli. Massive sandstone strata above the Bulli seam is the controlling influence on face conditions. The earliest equipment proved to be inadequate and the Company has progress- ively replaced and upgraded the roof supports and ancillary equipment so that the present units are capable of producing high and consistent outputs.

Jan 1, 1976

By M Carr, C Wheeler, M Lurie, B Chen

The demand for steel products in modern society is prompting the iron ore industry to optimise their operations to ensure sustainability of fines and lump products. One of the key components in the iron ore transportation chain are belt conveyors. The energy consumption of modern belt conveyor systems has reduced considerably over the past few decades, however, there is still significant scope for further reductions, especially when heavily loaded long overland belt conveyors are considered. A new rail based continuous bulk material transportation system has been developed by researchers at the University of Newcastle to reduce the energy consumption of heavily loaded and long overland conveyors. The Rail-Running Belt Conveyor technology is a state-of-the-art continuous belt conveying technology which provides an innovative and novel departure from conventional continuous bulk material transportation systems with significant energy and economic benefits. This paper presents an overview of a Rail-Running Belt Conveyor variant which considers an enclosed belt. Enclosed belt conveying has the benefits of encapsulating the bulk material, and thereby reducing dust emissions and moisture ingress, in addition to being able to negotiate smaller radius horizontal and vertical curves leading to greater flexibility. To quantify the primary differences between conventional conveying technologies, the Denver office of thyssenkrupp Industrial Solutions (USA) developed a case study for an 11 km long conveyor. The conveyor design throughput was 2750 t/h and included a small net elevation loss of 10 m. When considering CAPEX the Rail-Running Pipe Conveyor equipment supply cost is approximately 45 per cent of the cost of a conventional pipe conveyor, while savings upwards of US$50M emerge for CAPEX combined with five years of OPEX. The savings vary with the topography and density of the bulk commodity, with iron ore generally showing increased savings because the high bulk density increases rubber losses in conventional conveyors.

Nov 8, 2021

By A Valero, G M. Mudd

There is active debate and research around the most suitable indicators to assess the sustainability of mining. The most common approach is to report a range of data for a given mine site (or less preferably, a company total), such as inputs, outputs, benefits and potential costs. The most popular protocol in use (and growing rapidly) is the Global Reporting Initiative (GRI). However, these measures are numerous and still do not allow a single over-arching indicator to be developed. Other measures, such as known mineral resources over time, do not account for critical challenges such as declining ore grades, increasing wastes and poorer quality ores or more difficult mineralogy. By adopting a thermodynamic approach to sustainability, through the concept of æexergyÆ, it is possible to incorporate into a single measure the effective quality of mineral resources. Exergy involves the assessment of the minimum energy costs involved in producing a mineral resource with a specific chemical composition and concentration from common materials in the environment. The exergy of a mineral resource is evaluated from mineralogic composition, concentration (or ore grade) and, of course, quantity, by multiplying the unit exergies with the tonnes of the resource produced (or consumed). Since exergy is a thermodynamic quantity (ie energy or joules), it is additive across different minerals, such as iron ore to gold to copper or even oil and gas or coal û making it an ideal indicator to assess mineral resource sustainability at the industry scale rather than the individual mine scale. This paper briefly outlines the theoretical basis for exergy, and then presents a range of commodity case studies showing the application of exergy to the Australian mining industry. Overall, the usefulness of exergy is clearly demonstrated for use as a broad indicator of the sustainability of mineral resources at the national or even global scale.

Jan 1, 2009