Search Documents

By G J. Lyman

Sampling of grain for mycotoxins is challenging in that some mycotoxins, such as Ochratoxin A (OTA), have very low permitted levels and the kernels carrying the mycotoxin may be highly localised within the bulk of the grain as ‘hot spots’. Sampling for genetically modified organisms (GMOs) can be fraught with similar problems, especially if the contamination is adventitious and random. Incremental sampling under these circumstances can be shown to lead to a high variance in the sampling result.A new design of sampler for grain and other free-flowing particulates has been developed that is effective in practically eliminating the sampling variance due to distributional heterogeneity (DH).This paper introduces the design and argues that the sampler should be free of sampling variance due to DH.CITATION:Lyman, G J, 2017. A new sampler for grain and other free-flowing particulates, in Proceedings Eighth World Conference on Sampling and Blending , pp 277–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By L Neems

In conjunction with Orica Explosives, Worsley Alumina have managed a program of continuous improvement to their cap rock blasting over the last two years. Blasting conditions are challenging because of the hard and shallow nature of the material. Blasting costs must be controlled and the environmental consideration of noise and dust is critical. Worsley have sought to determine the optimum balance between drilling and blasting costs and fragmentation. As the cap rock has few inherent weaknesses, loader productivity is strongly controlled by the degree of fragmentation from blasting. The optimum blasting solution is also constrained by maintaining airblast levels at the surrounding residences below 115 dBL . The major blast design parameters optimised during the program were stemming type, stemming length, powder factor and blasthole diameter. A series of carefully managed trial blasts were fired during 1997 and 1998 to quantify the effect of these parameters. Fragmentation was digitally measured using OricaÆs Powerseive G technique. Shovel productivity, airblast levels and blasting costs were also quantified. As a result of the project, Worsley now have an increased knowledge of the key parameters driving blast performance, and their consequent impact on downstream processes, the environment and total mining cost.

Jan 1, 1999

By P A. Jenkins, I W. O Jones

WMC has mined the Perseverance disseminated orebody exclusively by SLC (sublevel cave) methods. Deteriorating ground conditions in the vicinity of an orebody inflection forced a re-evaluation of future mining at Perseverance and a strategy to drop down below the inflection zone and recommence the cave was implemented. This strategy has led to increased production at higher grades, resulting in lower costs and better mill recoveries. This paper describes the evolution of mine planning, development, support and production strategies through the successful process of implementing the ædrop-downÆ and re-establishing the SLC.

Jan 1, 2000

By C Mason, A Littleboy

This paper presents the results of a large scale survey of The Australasian Institute for Mining and Metallurgy (AusIMM) membership. This survey aimed to understand and define the key issues and drivers that AusIMM members perceived would shape the development of the Australian minerals industry over the next 20 - 30 years. Nine hundred and fifty-nine participants rated the importance of 11 issues and six drivers (generated from interviews with AusIMM members), and 236 of these participants also provided qualitative descriptions of the future. Issues were defined as problems or opportunities for the minerals industry that may be controlled or influenced by the industry, while drivers were defined as those factors that will influence the direction of the industry that are not within the control of the industry. The quantitative data revealed that the top four issues, in order of their perceived importance to the Australian minerals industry, were: investment in exploration, workforce, health and safety, and innovation. The top three drivers in order of their perceived importance, were: economics of mining, global context and Australian society. While the top four issues were largely consistent across professional groups examined, metallurgy and mineral processing professionals rated water inputs and energy inputs significantly higher than the other professional groups. For the list of drivers, there was strong agreement regarding their ranked order of importance across the professional groups examined. Within the qualitative data, however, a single issue (technology) and a single driver (economics of mining) dominated participantsÆ descriptions of the future. These findings provide important input into a broader program of scenario development for the Australian minerals industry being undertaken by CSIRO and its partners. The results of this study demonstrate the importance of using a mixed methodology in generating these inputs to understand more fully how important stakeholders view the future and the factors that will shape it. The results of this study are also discussed with respect to the role that CSIRO may play in facilitating the exploration of uncertainty around the future of the Australian minerals industry.

Jan 1, 2009

By Read T. A

PART 1The quantity of dust present and the methods used for suppression of dust in metalliferous mines has, in recent years, received considerable attention from mining engmeers in various parts of the world. Shortly after the publication of the General Report of the Miners' Phthisis Prevention Committee, South Africa, in 1916, the officers of the Broken Hill South Limited started investigations into the conditions of the dustiness of the air in the underground workings. As the methods used are not generally known in Australia, the writers are of the opinion that the present is an opportune time to place them before members of the Institute. A large amount of the subject matter of this paper has been drawn from the 1916 and 1919 reports of the Miners' Phthisis Prevention Committee, South Africa, the paper of Mr. Innes published in "The Chemical, Metallurgical and Mining Society of South Mrica"; also various articles appearing in the Journal of Industrial Hygiene, and the American Journal of Public Health. A great deal of research work into the cause, prevention and estimation of mine dust has been made by the Miners' Phthisis Prevention Committee of South Africa, and officials of the United States Bureau of Mines. The writers considered it advisable to begin the investigation at the South Mine with apparatus and methods developed by the South African Committee.Through the Australian agent of the Cape Explosives Company, inquiries were made preliminary to procuring the necessary apparatus for the determination of dust, from South Africa. The writers then learned that the older gravimetric method used by the Phthisis Prevention Committee was likely to be superseded by the konimeter...

Jan 1, 1922

By M Kuruppu

Large mining operations require a high percentage of the capital invested in mobile and fixed mining machinery. From an investment point of view this expenditure must be met by an equally high rate of return, thus the need for high plant and equipment reliability is of major importance. Equipment downtime is undesirable and very costly, resulting in lost production and revenue, which is of critical importance to successful mining operations. One of the solutions to this problem may be found in the form of competent computerised maintenance management software systems, which help to reduce the problem of breakdowns. These software assist the engineers for the management of service orders, resource allocation, progress monitoring as well as costing. They also facilitate the communication of targets and objectives among the service personnel. A computerised maintenance management software called MAINPAC was used to record and plan the activities of mobile equipment maintenance in a large mining operation in Western Australia. Among the details recorded were equipment data, service history, machine downtimes, previous maintenance, job planning and the resource required. This information further helped to analyse the maintenance efficiency, availability and the reliability of the equipment.

Jan 1, 2006

By V S. Svinin, V V. Rybin, V A. Maltsev

In large-scale mining, large-sized intermediate pillars, or block-pillars, are generated on the horizon or between closely located mines. These pillars are mined under high rock pressure that results from the stress concentration zones superposition from closely located working excavations. This problem becomes much more complicated if high tectonic stresses occur in the rock mass inducing a rock-burst risk situation. Mining experience gained in mining seven block-pillars at three Khibiny mines in Russia under the geomechanical situation like that described aboveÆ is discussed in detail. It has been shown how safe mine of block-pillars depends on their width, location relative to significant geological failures and uncaved rocks of the hanging wall, the order of pillar recovery, and application of special measures for rock mass stress relieving. Basing on the analysis of the mining experience and special scientific researches, the basic principles are worked-out for safe block-pillar mining under rock-burst prone conditions.

Jan 1, 2000

By S E. Wallah, D Hardjito, B V. Ran

The manufacture of Ordinary Portland Cement (OPC) is not only energy-intensive but also releases a significant volume of carbon dioxide (CO2) to the atmosphere. In addition, OPC in concrete often causes premature deterioration that affects the durability of concrete structures. This paper explores an alternative to OPC concrete called geopolymer concrete.The present research utilises low calcium (class F) fly ash as the source material to produce geopolymer concrete. Several factors that affect the mix design process such as mix proportion, curing time, and curing temperature have been studied. In addition, the long-term properties such as drying shrinkage, creep, and exposure to sulfate attack are also being investigated.The test data presented in this paper reveal that geopolymer concrete possesses high compressive strength, undergoes very little drying shrinkage and moderately low creep, and shows excellent resistance to sulfate attack. The result is extremely promising and demonstrates the sustainability of geopolymer concrete as a construction material for a sustainable future.

Jan 1, 2004

By Hall G

The Mount Isa silver-lead-,zinc deposit possesses a number of features which sets it apart from usual occurrences of ores containing those metals. The deposit has been described in vario:us papers, but development upon deeper levels during the past two years has, yielded much information not hitherto published. Purpose of the present paper is to furnish a unified and coherent perspective by tracing briefly the full rock deformational and mineralization processes responsible for the ore deposition. The paper represents the outcome of ten years' organized geological effort at Mount Isa. Information contained in it supersedes that previously published.A bibliography of published articles relating to Mount Isa ore deposition is appended. In preparing the present paper previously published data have been drawn upon freely wherever applicable. The authors are especially indebted to the papers by Grondijs and Schouten, and by O'Malley and McGhie, which present results of systematic microscope studies of thin and polished sections from comprehensive suites of Mount Isa ore.

Jan 1, 1942

By Tamura S, Maekawa M, Nagai C, Deguchi M

Heavy fuel oil has been injected into blast furnaces in order to reduce the coke rate, to improve productivity and to control the furnace heat condition. However, in the first oil crisis at the end of 1973, it became necessary to develop an injection technique of new fuels into blast furnaces to reduce oil consumption. In Kobe Steel, Ltd., it was thought that the injection of a coal-oil mixture (COM) into blast furnaces could be developed in a shorter time than pulverised coal injection. The development of this technique was under- taken in 1974, and COM was injected through two tuyeres of the No.3 blast furnace at the Kobe works in 1977 and 1978. In addition, in order to study the combust- ibility of COM and the phenomena in the tuyere zone, the development of a gas sampling method was under- taken in 1975. In this paper, the results of the injection tests and gas sampling tests are reported.

Jan 1, 1981

Remote sensing techniques can be used to map joint sets in a rock mass for the estimation of in situ block size distribution and improved optimisation of blasting. This paper reviews remote sensing using photogrammetry and laser mapping for mapping rock masses and presents elements of the analyses applied to data acquired with these mapping technologies. These techniques enable a user to map areas of hundreds of square metres rapidly with high precision. Using this data computer programs such as Sirojoint can provide estimates of joint position and orientation with orientation measurement accuracies better than one degree. The paper describes the use of remote mapping and provides potential users with a description of some of the advantages and limitations of the mapping techniques and the data they produce. Mapping of lithology and structure of rock masses is an important task required in many areas of mining and construction. It is a complex task routinely performed using established techniques developed to provide consistent results under a wide range of conditions. The techniques for data acquisition and analysis described in this paper enable more accurate mapping to be performed rapidly and enable mapping of inaccessible sections of a rock mass. These techniques will provide geologists and geotechnical engineers with more detailed, accurate data than previously available.

Jan 1, 2001

Longwall mining operations have been in place in Australia since the early 1960s. This mining method is currently used to extract the bulk of coal obtained from underground mines in Australia (CSIRO, 2010). Despite the high tonnages extracted the expected utilisation of much equipment remains relatively low. To some extent this level of utilisation is influenced by the variability in conditions inherent in the mining process. This variability in production rates presents challenges to those attempting to design a coal clearance system. The difficulty is to design a system that has sufficient capacity to support production, without over capitalising or incurring high operating costs. The need to allow for a series of largely unplanned events in the design of a coal clearance system makes simulation modelling an ideal technology to employ. Simulation modelling is a methodology that allows a system with interacting components to be modelled over time, while explicitly taking into account unplanned events that may disrupt operations.This paper discusses how dynamic simulation models have been used to assist in the design of coal clearance systems. Typically this type of modelling has been used to look at the likely profile of production rates from the Longwall shearer and to determine how well various proposed combinations of belts, bins and stockpiles would support production.

Sep 26, 2011

The Crown Minerals Act provides a new+framework for the management of Crown owned minerals and requires that regard be had for the principles of the Treaty of Waitangi. The Act requires the preparation of Minerals Programmes to achieve the Act's objectives of efficient allocation of rights and the recovery of a fair financial return on its minerals. Efficient allocation requires that a permit is allocated to the party which values it most highly. A fair financial return to the Crown must be considered in the context of the economic rent available from individual mineral projects, with the proviso that a nil return to the Crown as the owner of the resource will not be considered a fair return from the community's perspective.

Jan 1, 1992

By M Gao

Six new IsaMills were installed for the George Fisher flowsheet in the Lead/Zinc Concentrator of Mount Isa Mines to produce a product P80 as fine as seven microns. The objective was better liberation of galena and sphalerite. The IsaMill commissioning was completed by the end of 1999. The six new IsaMills were running to the metallurgical specifications almost immediately after start-up. This paper reports the performance of the George Fisher IsaMills in the zinc circuits and some of the latest development in the IsaMill designs and maintenance during George Fisher commissioning.

Jan 1, 2000

Australia is a significant exporter of uranium for use as fuel in nuclear generating plants around the world. Although Australia does not have any nuclear power plants the Australian Atomic Energy Commission has a research program on methods for the safe disposal of wastes produced by such plants.

Jan 1, 1986

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill, considering mainly the role and specifications of the fill used but including brief description of fill preparation and placement. Data resulting from a Portland cemented hydraulic fill sampling, curing and cesting campaign covering about 18 months of operating practice are presented, analysed and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented, involving both Portland cemented hydraulic fill and altei._acive, cheaper, additives for cementing hydraulic Fill.

Jan 1, 1980

By J Coombes

Within the mining industry there is a growing trend of placing inexperienced technical people into positions of responsibility beyond their readiness. Their responsibilities often include providing the fundamental basis for decision-making: the resource model or even the daily grade control estimates. Whilst software continues to make the processes more accessible, the thinking and rationale for selecting parameters still requires control rather than auto-piloting. Operators run these systems in virtual isolation, and have limited immediate access to experts. Beyond the stress of the professional burden are the increased risks to the mining operations and overall project success.While many experienced experts recall being thrown in the deep end, the relative isolation from experts coupled with the gravity of professional burden before readiness, is less familiar. Many recall in intimate detail the experts who gave them direction, assisted them along the way and even helped them claw out of inadvertent mistakes. Experienced professionals all have a responsibility to enable capability across the generations, to ease the burden and to mitigate the risks.This paper provides an outline of how mentoring as an on-the-job professional development process can be structured to more fully enable success of a mentoring program. Three examples complement the principles presented.CITATION:Coombes, J, 2012. Structuring meaningful mentoring, in Proceedings International Mine Management 2012, pp 15-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

Prior to 1972, Peko Mines Limited at Tennant Creek used a central mill at Peko, which consisted of a gravity circuit, flotation and cyanidation of tailings, to treat their gold ore from surrounding mines. The Warrego concentrator, 60km to the west, was built to handle the Warrego and Gecko copper orebodies, which were being developed concurrently with the concentrator construction The Warrego concentrator consisted of a flotation circuit, using autogenous grinding at 100 - 120 tph, compared to the more elaborate Peko circuit employing rod mill - ball mill grinding capable of treating only 18 - 26 tph. During development of the Warrego copper mine a gold rich ore pod was located, because of which the mining plans were adjusted to allow simultaneous, separate extraction of the copper and gold ores. However, the plans for the concentrator were not affected as the gold ore could be carted 60km to the Peko central mill for processing.

Jan 1, 1978

By J J. Jiang, B G. Bow

Atlas Iron Limited’s (Atlas) Abydos Mine has developed its Scarborough open pit proximal to a rock shelter that has been assessed as a significant Aboriginal heritage site by the Traditional Owners of the land. The rock shelter, named Yurlu Kankala, is located to the north-west of the pit with a stand-off distance of 35 m. Within Atlas’ Native Title Agreement with the Traditional Owners, and approvals from the Western Australian Department of Aboriginal Affairs, commitments have been made to conduct mining in a way that avoids or at least minimises disturbance and damage to the rock shelter. This complies with the Aboriginal Heritage Act 1972 (WA) and respects the heritage and culture of the Traditional Owners.CITATION:Bow, B G and Jiang, J J, 2018. Iron ore mining in proximity to a significant Aboriginal heritage rock shelter, Pilbara Region, Western Australia, in Proceedings Life-of-Mine 2018, pp 2–5 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

Anglo Coal Australia (ACA) takes a proactive position with regards to attracting and retaining employees at a graduate level. Currently, ACA has graduates in its program across all disciplines: Mining Engineering, Mechanical Engineering, Electrical Engineering, Commercial, Occupational Health and Safety, Environmental Engineering, Human Resources, Safety Engineering and Processing Engineering. The current program is three years in duration and involves two (generally) equal periods at different ACA mine sites or Brisbane Corporate Office. ACA takes an active role in promoting its status at the university level by maintaining a scholarship program. Six undergraduate scholarships are offered each year across all disciplines. Associated Vacation Employment is offered to each scholarship holder during the period of his or her university study. This commitment to education is regarded highly by future graduates. ACAÆs active role in sponsoring student bodies is also known and appreciated amongst the university population. ACAÆs graduate program has been a successful training program for future leaders of the coal mining industry. The company is committed to making the program more suited to the needs of the graduates across all disciplines and as a result the program is not stagnant but is constantly changing and evolving. Recently the æGraduate PassportÆ has been drafted with an aim to keep each graduateÆs needs in relation to experience and training firmly in focus for the duration of the three-year program. Appropriate training for each graduateÆs position is supported by the company; for instance, support through funding and time for a commercial graduateÆs CPA qualifications is provided.

Jan 1, 2005