Search Documents

Due to highly competitive international coal markets, Stockton mine is bound to produce very high quality coals consistently if it is to maintain and expand its market share. The nature of the deposit is such that coals from various source pits are blended in differing proportions to meet the various coal quality specifications of the customer. The complexity arises due to quality variation within the seam both horizontally and vertically and the fact that up to six different products with completely different quality specifications may have to be produced. With increasing demand for this rare product and with CoalCorp eager to meet this demand comes the requirement for computer methods to handle this highly complex problem of both modelling and scheduling.

Jan 1, 1989

By M Miettinen

That microorganisms, both living and dead, and products derived from the organisms, can function as flotation agents and flocculation agents is abundantly clear. They can modify the surfaces of minerals. They can function as flotation collectors and as flotation depressants and activators. In many cases they or their products can function as specific flocculation agents. Problems that must be solved before such microorganisms or products from the organisms can be used in commercial operations include culturing the organisms at a cheap cost and reduction in dosages required for various separations. These tasks are formidable. However, the concept of using such natural materials in place of various chemical reagents that may be toxic is very attractive. An attempt is made to show some of the promise of microorganisms in mineral bioprocessing and to consider the problems that must be overcome before commercial application of the technology is realised.

Jan 1, 2005

By B Murphy

Safescape Laddertube provides an improved system for emergency egress in ventilation shafts. The addition of Laddertube in a rise has very little impact on ventilation flow, studies have indicated that the difference in flow velocities are difficult to measure due to the minimal impact. Due to the size and open-ended nature of Laddertube, the air velocity inside and out of the Laddertube is mostly linear. Laddertube can be used either permanently or during an emergency as a secondary ventilation duct. One project involved a 385 m ladder installed in a surface return air raise that could be made to bypass the primary circuit and supply fresh air to a sea container fresh air base at the bottom of the raise. Laddertube has been designed to be installed to any feasible length and can be fitted with a climb assist system ensuring enhanced speed and reduced fatigue during ascent. The climb assist used in association with Laddertube is a Tractelift system which applies a weight relief of up to 36 kg off the climber’s body weight when using the ladder. This system has successfully been tested for ladders up to 600 m in length and is currently in use for a ladder of 185 m length. The use of refuge chambers in underground coalmines has long been a contentious issue due to the concern that while it may provide temporary shelter, the risk of being exposed to high heat or the inability for rescuers to access them due to fire or explosive atmosphere means that they may be effectively trapped. The additional application for coal environments includes Laddertube installed alongside a refuge chamber concealed behind a blast proof door ensuring a secondary means of emergency egress. In certain operations designs may allow for this chamber to be provided withpositive pressure fresh air.

Oct 12, 2022

By Van Deventer J S J

The first step in the design of a process to treat a possible economic precious metal deposit should be an examination of the mineralogy of the ore. Using this and other initial tests, the extractive metallurgist can design a process to treat the ore. In the field of precious metal metallurgy, little emphasis is placed on the mineralogical information available to the metallurgist. The information is of far more use to the geologist and the mining engineer. Diagnostic leaching was designed to open up the field of mineralogical analysis to the metallurgist. When a mineralogist looks at the deportment of gold in an ore, he is usually looking for an element which is present in parts per million, so that errors in sampling are multiplied dramatically. Diagnostic leaching offers a cheap, simple, practical alternative. In order to determine with which minerals the desired precious metal is associated, a specific mineral is first eliminated using a selective oxidative leach, and cyanidation is used to extract the precious metal (in this case gold and silver) liberated by the destruction of this mineral. The precious metal extracted can be measured in solution to give a fairly accurate record of the amount of the precious metal associated with that mineral. Furthermore, the residue from this first stage can be subjected to another selective acid leach, and the process repeated. The procedure can be varied to suit the mineralogy of the matrix material. At the end of this diagnostic leach the metallurgist is left with a complete record of the deportment of the precious metal. He can now use this information to design a metallurgical flowsheet to treat the ore. Diagnostic leaching is thus an analytical tool which can be used by the metallurgist not only to examine new ores, but also to look at problems occurring at existing plants. The procedure is not only limited to ores and residues but in fact can deal with any type of intermediary product that occurs on a plant. The information gained from analysing an intermediary product can give a useful indication of how well a unit process is working, eg flotation, roasting, etc.

Jan 1, 1992

A large body of porphyry-type copper mineralization occurs at Panguna in southern BougainviIle. It is associated with the intrusion of quartz diorite/granodiorite into andesites, particularly with the contact zone. Metasomatism of both intrusives and andesite resulted in the formation of biotite pseudomorphing hornblende and the veining of the resultant biotite diorite and biotitized andesite by quartz-chalcopyrite veins with pink orthoclase and dark biotite selvages, respectively.The orientation of intrusives and veins appears to be controlled by premineralization fault-joint patterns in the intruded andesitic Kieta Volcanics.

Jan 1, 1968

By L Rachmad

Freeport IndonesiaÆs Deep Ore Zone (DOZ) mine is the new underground block caving mine within the East Ertsberg Skarn System (EESS) deposit which started production in mid-2000. The DOZ will produce 25 000 tpd using mechanised block cave mining method and will be the fourth underground mine opened within the EESS deposit. Evaluations were made on former block caving mines at PT Freeport Indonesia (IOZ, GBT Area I and II) in order to design a more appropriate support system. As a permanent support, the thread bar bolt support system is widely used in the DOZ mine. The advantages of this system are ease of operation, quality control and high bond strength. The main problem of this system is the curing time of about 28 days to achieve maximum strength, necessitating the installation of a temporary support for its implementation. In this instance, the system was inefficient in operation and studies were required to find an alternative grouting system. This paper examines the evaluation of thread bar bolt support system and compares the performance of two types of grouting (resin cartridge and cement cartridge) with cement grouting performance. The evaluation is conducted with a pull out test. The advantages and disadvantages for each grouting method, comparison of cost estimation and grouting application in mine scale are presented in this paper.

Jan 1, 2002

By P M. Dight

Shotcrete usage in declines and developments has become pervasive as operators strive to achieve production improvements. Issues of mix control, fibreload, thickness control, temperature and curing conditions all play a part in the quality control. Often to overcome some of the quality control issues designers over specify the strength requirements in order to meet their operational constraints. Adherence to the standard civil testing requirements of 28 days moist cured at 21ºC without properly calibrating these results to the changing environment underground leads to contractual disputes. There are a number of standard tests specified including cylinder tests, cored tests, beam tests and round determinate panel (RDP) panel tests. The logistics of storing these samples and then transporting them to concrete testing laboratories without due regard to temperature changes with time can influence the results. All the samples can be readily handled by personnel except the RDP panel. The standard RDP panel is 800 mm diameter by 75 mm thick and requires an ITH machine at the mine and a fork lift at the laboratory to move it around. This paper will examine the possibility of a panel which provides scalable results to the standard RDP panel but can be easily handled by personnel and/or tested on site with suitable equipment. This allows for faster turn around and better quality control for the sample prior to testing. This enhances the identification of quality control issues at the mine and improves safety.

Mar 21, 2011

By J Karlovšek, M Hafner, M Žibert

The transport network in Europe is probably one of the most important systems for the European economy and society. Trans-national transport routes play a vital role in the traffic of goods and the supply of the population. In this respect, critical road infrastructures, like bridges, tunnels or control centres, can have a bottleneck function. Any disturbance of these structures could lead to negative consequences for the population and the economy as a whole.Project SecMan – Security Manual – is a simple four-step procedure for the identification of critical road infrastructures; assessment of these infrastructures regarding various man-made threats and the determination of effective protection measures was developed. These methodologies are summarised and combined into a comprehensive best-practice manual that allows for a trans-national structured and holistic security-risk-management approach for owners and operators of road infrastructures in Europe.Currently no common processes, methodologies or standards exist in Europe regarding the consideration of security relevant events for critical road transport infrastructures, eg tunnels, control centres and bridges. Attacks on the former can have severe short- and long-term effects with high media attention. A trans-national risk management approach would increase the possibilities for prevention as well as mitigation. A trans-national emergency response strategy would increase preparedness, as well as facilitating and accelerating the reaction in the case of an event.The main objective of the project is to develop a practical process for the identification of critical road infrastructures based on generally accepted security aspects. The assessment of these infrastructures would be carried out in a structured and traceable way regarding security relevant risks and the determination of effective protection measures for prevention and mitigation.The project is implemented by the German Federal Highway Research Institute (BASt) together with project partners from Austria (ILF) and Slovenia (DARS, ELEA iC).CITATION:Hafner, M, Karlovšek, J and Žibert, M, 2014. Road infrastructure security assessment and measures selection methodology using secman – tunnel example, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 69–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The metals titanium and zirconium and their alloys occupy individually unique positions in the catalogue of metallic materials available for engineering applications. Because of the uniqueness of their usage in the aerospace industry, in the case of titanium, and in the nuclear industry, in the case of zirconium, the except- ional resistance of both the metals to the majority of corrosive media is often overlooked. The cost factor in the application of these more exotic metals has, in the past, been a major considerat- ion in the rejection of titanium and zirconium as constructional materials in areas of usage where their superior corrosion resistance strongly favoured them over more conventional metals and alloys. The cost differential, vis-a-vis austenitic stainless steels, for example, is not a trifling matter, being of the order of 6 : 1, when compared on a weight basis. However, if one considers the cost, for, say, sheet product on an area basis, the ratio is redgced to approximately 3.4:1. If one also takes into account the enhanced performance of the more expensive material and the sub- sequent increase in service life and decrease in plant down-time, the economics of the usage of materials such as titanium becomes much more attractive and, indeed, highly competitive,

Jan 1, 1969

By T Craske, J Sykes, T C. McCuaig, M Jessell, A Trench

The prevalent strategic approach in the mining industry is one of planning. However, it is widely recognised that planning does not work in complex and uncertain situations (Mintzberg, 1994), such as those associated with ‘above ground’ non-technical orebody complexity (Trench, Packey and Sykes, 2014). Mintzberg, Ahlstrand and Lampel (2009) suggest the focus instead should be on strategic ‘thinking and doing’ and using the many ways to think about strategy to make sense of complex, uncertain, and unique situations. They therefore place great value in cognitive flexibility. Scenarios development utilizes several different thinking styles and thus assists with this type of flexible strategic thinking (Figure 1). The ‘Centre for Exploration Targeting (CET) Scenarios’ were developed with the ‘Oxford Scenario Planning Approach’ (OSPA) (Ramírez and Wilkinson, 2016). The OSPA aims more to improve the thinking skills of decision makers, rather than forecasting per se (Wack, 1985a, 1985b). As such, this paper focuses less on the content of the scenarios and instead on the practical value of scenarios in strategizing. CITATION: Sykes, J, Trench, A, McCuaig, T C, Jessell, M and Craske, T, 2018. Strategic thinking about long-term ‘above ground’ orebody complexity using scenarios, in Proceedings Complex Orebodies Conference 2018, pp 60–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By P Donecker

Like all chains, iron ore values chains are only as strong as their weakest link, which in ore processing is often the humble chute. While mechanically the simplest element in the iron ore flow sheet, chutes are often the most problematic and regularly the major cause of unscheduled downtime. Chute designs have remained static for decades, despite the extra demands being placed on them by grade reduction, which impacts chutes in three ways viz: 1. Higher volumetric rates as infeed increases to meet production targets. 2. Higher moisture content as mining goes below water table. 3. Stickier properties as the dilution phase is often clay based. While there is no shortage of ideas and the geometry options are infinite, the fact is that chute design has not kept pace with grade decline and has remained essentially unchanged. One reason cited for this lack of innovation is the difficulty evaluating and de-risking designs. While the power of computers running Discrete Element Method (DEM) models has advanced, the models themselves still need to be ‘calibrated’ with the dynamic properties of the ore. Flow properties commonly measured for bin design are useful for static situations only and were never intended to predict dynamic behaviour as in chutes, a critical qualification lost in the mists of time. So while they always produce a colourful and reassuring animation, DEM models informed by static ore properties often result in wildly inaccurate real world predictions. Responding to this low success rate, many operators are now utilising physical modelling to help reduce risk and avoid the consequences of having an underperforming chute in their value chain. Physical testing, in a dimensionless scale-down of the proposed system (bulk material and chute geometry), addresses the shortcoming of mathematical models designs and when used in combination with DEM is the best option. In the ideal world, the focus of chute modelling should be innovative design concepts aimed at addressing future needs, however in reality the focus is nearly always on modifications to installed chutes that are underperforming even today. This situation can be traced back to design procedures which if informed at all, are based static ore properties. As an industry, we need to break this cycle and become more proactive, which means addressing flaws in the current design process. In 30 years of providing modelling support to the industry, I have looking at hundreds of underperforming chutes in the iron ore industry. This practical experience has led to a unique and unbiased perspective on chute design and their performance in the real world. The knowledge presented in this paper can not only be used to help avoid baked-in problems now, but also help guide and evaluate designs so we can deal with the challenges of our low-grade future.

Sep 18, 2023

By A Weeks, W J. Shaw, A Kuk

Grade control is a process that requires the interaction between many components of the mining operation and successful grade control is only realised through good data, robust systems, and a well-trained, motivated and disciplined workforce.The Mt Magnet Gold Project Pty Ltd (MMGP), a wholly owned subsidiary of Ramelius Resources Limited, started mining at Mt Magnet in February 2012 with high expectations for success. Positive cash flow would fund an aggressive exploration and mine development program in the area to increase mine life. Disappointment followed when after start-up the operation had issues achieving budget grade and realising the predicted grade of the mined ore. In January 2013, things started to improve. During the next six months, gold production steadily increased with successive months achieving record production. What had changed?Improvements started following the realisation that controlling grade was not the sole responsibility of the mining geologist and that everyone on-site has a role to play. This paper examines the factors that delivered success for MMGP.CITATION:Weeks, A, Shaw, W J and Kuk, A, 2014. Who is responsible for grade? – an evaluation of the value chain at Mt Magnet Gold Project, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 477–482 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By A Hall, D Kratochvil, P Littlejohn

Economic recovery of gold from complex gold ores, including poly-metallic deposits, is impacted by the presence of cyanide-soluble base metals. These base metals can create both a metallurgical challenge plus waste handling and disposal challenges. Base metals such as Cu and Zn compete for the cyanide reagent and often increase the total cyanide consumption to the point of making precious metals recovery uneconomic. In addition, the accumulation of base metals in cyanide solutions represent a challenge for cyanide detoxification and waste water treatment as these metals report to waste sludge. Such sludge requires safe handling and disposal, with possible long-term liabilities.Base metal interference can be removed with sulfidisation-acidification-recycling-thickening (SART) process technology. SART liberates the base metal from the cyanide complex and precipitates the metal as an insoluble sulfide product that can be recovered as a commercial grade concentrate. With the base metal precipitated, the cyanide can be regenerated as free cyanide and recycled to the gold extraction circuit.BioteQ completed laboratory testing for two projects, one employing cyanide leaching of copper-gold sulfide flotation concentrate and one employing a Merrill Crowe process, to determine the effectiveness of SART to remove and recover Cu and Zn in high-grade sulfide concentrates and to reduce the impact of cyanide-soluble metals on gold recovery and cyanide consumption. This paper will provide an overview of the testing methodology and results along with a review of the potential for SART to be applied to complex gold ores with poly-metallic deposits to improve project economics, operability and waste management.CITATION:Littlejohn, P, Kratochvil, D and Hall, A, 2013. Sulfidisation-acidification-recycling-thickening (SART) for complex gold ores, in Proceedings World Gold 2013 , pp 149-156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Peculiarities of Quartz Distribution in Zinc Flotation Products and their Influence to Mineral Processing

Sep 13, 2010

By J J. Cilliers, K Hadler

Air is fundamental to flotation; not only is it required to collect the valuable particles, but it also controls the froth stability and consequently the separation performance for a given feed. Froth stability can be described and quantified in numerous ways, which are subtly different. Air recovery is one such measure of froth stability which accounts for both the stability of the bubbles and the mobility of the froth. The benefit of using air recovery as a measure of froth stability is that it exhibits a peak as air flow rate is increased, and this corresponds to the air rate at which the optimal separation performance is obtained. As such, it provides a single target value for optimising air flowrate for a given set of feed conditions. Use of air recovery, however, has one potential drawback: accurate measurement of the inlet air flow rate to a flotation cell is required. This can be problematic for operations, particularly where calibration of air flow rate is carried out infrequently or where there is no air flow rate measurement, such as for many self-aerated flotation cells. To this end, we present an alternative method for determining the peak in air recovery (PAR) air rate.We introduce a simplified method for determining the PAR air rate using trends in froth velocity and overflowing froth height, both of which are readily measured using existing froth image analysis systems. We will show, using industrial data, the application of this simple technique to find the optimal air flowrate for flotation cells. We will also discuss other alternative techniques for air rate optimisation that have the potential to improve separation performance using existing technology.CITATION:Hadler, K and Cilliers, J J, 2018. How to find the optimum air rate for flotation cells, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By R Ballantyne, M Adams

Time Usage Models, used as a basis for calculating performance indicators for mobile mining equipment, have developed from very simple to very sophisticated models. This development has paralleled the increased collection and analysis of production data that itself has been enabled by the evolution of underground voice and data communications along with the relevant information systems. A Time Usage Model divides the hours that equipment is (or is not) used into standard components, by a hierarchical breakdown, so that measures of productivity can be used to compare performance of both people and equipment. The calculation of equipment availability, and thus the underlying Time Usage Model, has always been an extremely emotive topic as different groups use time usage information for different purposes. The direct link between measuring performance Key Performance Indicators (KPI) calculated from these models and employee rewards impacts upon the workforce. This paper discusses the conflict in use by various stakeholders and proposes ways to address some of the more contentious issues each supported by case studies. The simple status code functionality used by early systems has proven inadequate, leading to the evolution of “work-arounds”. These workarounds have become the norm and unfortunately have become embedded in the next generation of models and the information systems that incorporate them. This paper contends that the industry should stop building Time Usage Models to accommodate shortcomings in proprietary systems, but rather collaborate with suppliers to develop innovative methods to deal with the fundamental requirements. There are many points of differentiation that are not clear-cut. Pitfalls are discussed as well as threats to success. A framework of rules is developed as guidelines for how a Time Usage Model should be developed and applied. This will hopefully stimulate the on-going discussion as to how Equipment Availability and other components of the model should be calculated.

Mar 15, 2021

By S Henderson, J V. Lawless

The worldwide association of low-sulfidation epithermal gold mineralisation, bimodal rhyolitic-basaltic volcanism and rifting is confirmed in New Zealand. In the currently productive Coromandel epithermal-gold province reported Ar-Ar dating of adularia from low sulfidation deposits falls into two groups at 6 and 7 Ma. Bimodal rhyolitic-basaltic volcanism has been reported to be K-Ar dated at 9 to 7 Ma and 6 to 5.5 Ma. Epithermal gold mineralisation in Northland is spatially associated with bimodal basaltic-rhyolitic volcanism, with rifting cogenetic with that in the CVZ. The Taupo Volcanic zone (TVZ) is sufficiently young that the presence of a segmented rift with recent bimodal rhyolitic-basaltic volcanism can be genetically associated with epithermal gold mineralisation, which occurs as both fossil occurrences and in active geothermal fields. This reinforces the known potential prospectiveness of the Coromandel area and increases that of Northland and the Taupo Volcanic Zone.

Jan 1, 2005

By Tapp BA

Australia, considered an energy and mineral resource rich country, is poised on the verge of a major mineral industry 'boom'. It has been repeatedly emphasised that this growth in the mineral industry will form the basis of future economic development. Currently the mining and mineral processing industries use some 32% of the annual primary energy consumption in Australia. This share, although large even now, will increase with the realisation of the 1980's production expansions to 40% by 1985. Two metal industries dominate the energy scenario; iron and steel and aluminium. Major expansions in the local industry will be dominated by the aluminium industry. This highly energy intensive industry has planned major increases in metal production throughout the eighties. The implications of exporting cheap energy to pay for expensive oil imports, the ramifications on Australia's infrastructural ability to supply these major energy needs and the other options that might be

Jan 1, 1981

By D N. B Skinner

Changes in the configuration of late Cenozoic volcanic arcs related to Pacific-Australian plate convergence in northern New Zealand may have localised large-scale epithermal gold-silver mineralisation to a particular part of the volcanic arc system, the Coromandel Volcanic Zone (CVZ). The history of arc-type volcanism in northern New Zealand began with the development of the continental margin Northland Volcanic Arc from early-mid Miocene (26-15 Ma). From 18-15 Ma the Northland Volcanic Arc extended south into the northern and western part of the CVZ where it is dominantly composed of andesite with lesser dacite and very minor rhyodacite. In the south, centre and east of the CVZ, younger andesite-dacite volcanism overlapped in space and time (14-5 Ma) with voluminous rhyolitic volcanism associated with rift-hosted calderas and minor basaltic eruptions. This change to bimodal rhyolitic-basaltic volcanism and extensional tectonics was a result of southwest (SW)-directed propagation of the Colville-Lau oceanic island+ arc into the north-northwest (NNW) trending Northland Volcanic Arc and its underlying continental crust. The extensional tectonic regime created in the collision zone between the two arcs is also the site of the 14-6 Ma Coromandel epithermal gold-silver province, which contains some 50 separate deposits and has a production (1862-1996) of about 300 t Au and 1150 t Ag. Extensional tectonics facilitated the emplacement of silicic magma at shallow crustal level and led to reactivation of deep basement faults. The resulting enhanced heat flow and fault-focused fluid flow localised large hydrothermal systems and associated extensive low-sulphidation epithermal gold-silver deposits in the southern part of the province, as at Waihi, Golden Cross and Karangahake.

Jan 1, 1997

By Robertson K. S, Hunter T. C

AEG-Elotherm's electromagnetic dosing channel, or Eldomet, is a recent invention enabling the transport and metering of molten metals. The development of a reliable refract- ory lining, and the use of suitable construct- ion and operating techniques has led to the successful application of the Eldomet for casting copper anodes at Copper Refineries Pty. Ltd.

Jan 1, 1974