Search Documents

Holla has given a good background to the various methods of subsidence control in the coalfields around Sydney.The present writer notes that in many cases, especially with wide longwall panels, there is not the flexibility to alter the mine layout as there is to some degree with the various pillar extraction methods. For this reason it may not be possible to plan the workings to minimise subsidence and some damage to structures may occur. The cost of repair or the cost of subsidence provisions to minimise damage may be small in relation to the tonnages of coal which would otherwise have to be sterilised. One method of subsidence control which has been in use in the Newcastle area since 1970 is the panel and pillar layout (partial extraction layouts with stable pillars). An extracted panel width of 0.6 times the depth of cover resulted in a maximum subsidence of 115 mm for an extracted seam thickness of 2.2 m.As Holla points out, the extracted panel widths in relation to th depth of cover depend on the particular geological setting. His Fig. 3 shows that the subsidence over a panel width of 0.3 times the cover depth in the Southern Coalfield is the same as over a panel width of 0.55 to 0.6 times the cover depth in the Northern Coalfield.Selective pillar extraction and longwall mining can both be used in the panel and pillar layout. Holla's Figs 2 and 3 are used to estimate the maximum subsidence over an extracted panel of known geometry. Maximum subsidence is related to seam thickness. What provision is made for a reduction in subsidence due to the coal which remains behind in a pillar extraction panel if the pillar recovery is poor? The writer suggests that an effective seam height could be used, based on the actual mining height reduced by a factor to account for the percentage recovery of coal from an extracted panel.

Jan 1, 1986

The Performance of Benzyl Arsonic Acid as a Collector in the Flotation of Wolframite and Cassiterite Slime

Sep 13, 2010

By S Tyrrell, B Jackson, K Matson

Northern Star Resources Limited Jundee Gold Mine in Western Australia operates a comminution circuit that consists of a primary crusher, 3.85 MW semi-autogenous grinding (SAG) mill, 1.8 MW ball mill and pebble recycle crusher. In 2017, a secondary crushing circuit was installed to remove the SAG mill throughput bottleneck and increase production of highly competent underground ore from 1.35 to a minimum of 1.7 Mt/a.This paper discusses the findings from the trial phase, the circuit design, project delivery, site optimisation, and the plant performance.CITATION:Matson, K, Tyrrell, S and Jackson, B, 2018. The application of secondary crushing at the Jundee gold mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 485–496 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Radioisotope x-ray methods for the on-stream determination of copper, lead, and zinc in mineral product slurries were developed, and were successfully tested at the plant of Cobar Mines Pty. Ltd.The tests were made in three stages. Measurements to determine the precision of analysis were made initially on briquettes of the mineral products. The effect of slurry solids content variations was then determined by measurements on the mineral products in a recirculating slurry loop. The radioisotope analyser was finally tested in a series of on-stream measurements in the plant.Copper, lead, and zinc in flotation feed and in copper concentrate were determined to a precision ranging between 1·4 and 15 per cent of the mean element concentration in the slurry solids. These precisions are within limits required for plant control purposes at Cobar.

Jan 1, 1971

By R G. Moreby

The purpose of this paper is to provide the rationale for decision making when considering the use of three heading gate roads in Australian underground coal mines.There are currently 30 underground longwall mines in Australia with all but two employing two heading gate road longwall layouts. The volumetric capacity of these two heading ventilation circuits is evidently viable in typical block lengths and in low to moderate gas regimes. However, in gassier regimes, potential longwall production rates of 10 Mt/a, and or where block lengths are being extended to well beyond historical norms, a conventional two heading U circuit may not be adequate. Other than seam gas emission, block length and production dependent heat loads together sealed area management requirements also have to be considered.The two mines currently employing three heading gate roads have the opportunity to revert to two headings at any time but, based on operational experience to date, have not done so due to the consequential reduction in gas management capacity and lower production rates associated with gas delays and limitations on tailgate access.Although there are a number of alternative two heading longwall circuits available and employed worldwide, the custom and practice of promoting inert goaf atmospheres in most Australian coal mines to mitigate the risk of catastrophic gas explosions and spontaneous combustion often prevents the use of gas loaded bleeder systems. In this respect, Australian underground coal mines may be considered the safest in the world.The current situation is that three heading gate roads have been proven successful in Australian conditions, albeit at additional cost, where two heading ventilation circuits cannot manage net seam gas emission to the ventilation system at the production rates required. In this respect, a further important driver for decision making is the short to medium term value of CO2-e emission taxation in Australia.CITATION:Moreby, R G, 2013. The rationale for use of three heading gate roads in Australian underground coal mines, in Proceedings The Australian Mine Ventilation Conference , pp 13-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The discussion which followed the publication of my paper by the formert has, I think, enhanced its value. It may therefore be of interest to members of our Australasian Institute, who are not members of the Institution of Mining and Metallurgy, if I give a synopsis of the discussion.My attention was drawn to the fact that my paper did not make clear the extent of the improvement in furnace operations, which followed the use of coke of high quality; this comment applied more particularly to the lead content of slag. My failure to supply comparative figures in regard to the lead content of slag was governed by a condition which, I think, is of interest to metallurgists. As a result of industrial...

Jan 1, 1932

Support design in jointed or blocky rock masses is often approached by the use of either 'rules of thumb', rock mass classification systems such as the Q-system (Barton, Lien and Lunde, 1974) or RMR (Bieniawski, 1973) or conventional wedge analysis. Generally, this requires that a number of key simplifying assumptions are made and the support system is designed to cater for either a mean, most likely, or worst case scenario depending on the risk tolerance. The design block size is often a major uncertainty and often a worst case block size based on excavation span is used. Thompson and Windsor (2007) state that it is inappropriate to base support designs on the excavation size as these size blocks rarely occur if discontinuity trace lengths are considered. Probabilistic keyblock methods can be used to determine the most likely design block sizes. A methodology is presented whereby JBlock software (Estherhuizen, 1996) is used to estimate potential block sizes as part of the support design process. Using information such as the spacing, orientation and length of discontinuities, it is possible to simulate blocks in the walls of an excavation (Esterhuizen and Streuders, 1998). Keyblock analysis methods (Goodman and Shi, 1985) are used to evaluate whether blocks are removable and whether the chosen support will be sufficient to ensure stability. Data from two mines is used to demonstrate how probabilistic keyblock analyses can be used in support design. Discontinuity data was used to generate 10 000 removable blocks and the design block size statistics were determined. For one mine this information was used to scale blocks in a conventional. Unwedge analysis whilst for the other mine, the point estimate method (Harr, 1987) was applied. The choice of appropriate design acceptance criteria in terms of factor of safety and probability of failure is also considered.

Nov 25, 2010

Resonance re-emission from nickel vapour affords a convenient method for isolating the resonance lines at 3415A, 3515A, and 3524A. The vapour is generated by cathodic sputtering and is illuminated by light from a nickel atomic spectral lamp. The resonance lines thus isolated can be usefully employed for absorption measurements on mineral samples where the nickel concentration is too high for measurements with the more sensitive line at 2320A. A spectrophotometer employing a resonance lamp as monochromator possesses several advantages where a great number of determinations are made under routine conditions. The wavelength setting is stable under even the most rigorous conditions and with the provision for automatic setting of full scale deflection the instrument requires virtually no adjustment. The instrument has been used under routine conditions for the determination of nickel (in the range O· 05-2 per cent) in mineral samples.

Jan 1, 1968

By D Crequer

A Peer Review Panel for the Golden Cross Mine in the upperWaitekauri Valley, Coromandel was initiated in December 1989, before mining, as a requirement of the conditions of the Mining Licence and Water Rights. The panel's function is as a technical audit and advisory team - to provide independent technical review of design, construction, and execution of mining operations, slope remediation works, and reclamation/mine closure activities. The primary role of the panel is to act in the public interest by providing assurance to regulating authorities that the design and application of on-site mining operations accords with 'good industry practice'. Panellists are not involved in design nor as advisers, although until 1997 when explicit terms of reference were written, the panellists were a sounding board for some operational proposals. The panel functions to ensure that best mining industry technical standards are met. The costs of the peer review process are met by the mining company. Review of mining operations includes environmental matters such as land rehabilitation and water quality. The focus of this paper is on the process of peer review for environmental management factors rather than for structural and mine engineering.

Jan 1, 1998

By Hara Y, Arino S, Nakamura M, Tachimori M

The theoretical and experimental studies have been done to clarify the hearth flow of iron and slag. The results of dissections show that the hearth can be treated as a packed bed of coke hav- ing good permeability with a coke-free layer at the bottom of the hearth. 3-dimensional numerical calculations of hearth flow with and without a coke-free layer are carried out, and the results are assured by a water model simulation. The influences of a coke-free layer on the iron flow and the discharge route of iron and slag are examined. The 3-dimensional flow pattern can be represented simply by the travelling time, which depends on characteristically the profile of coke-free layer and the quantity of iron in the hearth. Those flow parameters could be obtained by the results of radioisotope tracer test ( Co for iron flow, and Sc for slag flow) at several furnaces. As a result, it is found that the coke-free layer repeats the cycle of appearance and disappearance at several-month intervals. This cycle corres- ponds to large temperature fluctuation at the bottom of hearth. The relation between iron flow and skull (solidified iron, coke and deposited graphite mixed layer) on the hearth brick was studied by the model experiment and the thermal analysis based on the indications of thermocouples installed in the bottom of the hearth. If a thin coke-free layer is formed on the skull, a fast iron flow is generated in the layer, and melts away the skull. The growth and melting of skull produces the fluctuation of thermal load on a bottom brick, causing brick Damage.

Jan 1, 1981

By C Tonkin, S D. Howell, P V. Johnson, J Moriarty, P W. Duck

This paper presents the scientific framework underpinning the resource valuation and optimisation model (RVOM). The RVOM is a partial differential equation based real options software package, which helps mine owners optimally plan their operations, understand their project risks, and make defensible valuations. This is achieved in the presence of both financial and physical uncertainty, as well as processing capacity constraints. The RVOM can be applied to any multi-ore mine, open pit or otherwise, where the block-order of extraction has already been planned using existing software tools such as the Gemcom WhittleÖ strategic mine planning package. The RVOM can also take account of multiple commodities within a single mine, and multiple forms of price behaviour. The three key outputs from the RVOM are: valuation, optimal decision and probability of decision. A decision takes account of upfront costs, and can include an unlimited number of transitions between: normal operation, expanded operation, care and maintenance and abandonment (and variants thereof). The RVOM then employs stochastic process theory to determine the probability of reaching these decisions. This gives the mine operators clear indications as to where their risks lie, aiding their mine planning. A clear example of the RVOMs usage to a case-study gold mine is presented, demonstrating its broad applicability, the added value it can create and how users can easily make use of the RVOMÆs state-of-the-art algorithmic engine.

Sep 26, 2011

Hydraulic backfill is generally retained in stopes using permeable barricades. Mitchell et al (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et al (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading conditions. This paper discusses the circumstances that led to these incidents and analyses the modes of failure. The standards for the safe operating of hydraulic backfill systems are reviewed along with requirements for ongoing management and control. The design requirements of barricade construction are analysed and some appropriate guidelines introduced.

Jan 1, 1998

By T Baumgartl, D Bradshaw, B Forsyth, M Edraki

In a tailings storage facility, the chemistry of pore water is a function of oxidation and dissolution of sulfide minerals, containing metals and metalloids, the neutralising effect of gangue minerals and the geochemical processes controlling solute equilibria such as pH, redox potential, precipitation, ion exchange and adsorption. On the other hand, the changes in geochemical composition of tailings feed over time is a function of spatial variability within the orebody and modifications in processing method. Tailings properties such as pyrite content, pH, concentration of deleterious elements, surface chemistry, pore water chemistry and particle size are already shaped in the dynamic environment of a process plant.To engineer desired environmental outcomes, a new research framework is needed. The new approach should follow the physical and geochemical processes of tailings feed and construct models that can be used for the prediction of seepage water quality and dust propagation and evaluate the potential re-processing of tailings or production of tailings with desirable surface chemistry, particle size and internal structure. The challenge of developing tailings engineering model is not in laboratory techniques, but more of the overall communication of results and establishing the link between disciplines. It requires investigating geochemistry across mining and processing for improved environmental outcomes at tailings storage facilities.The paper reviews the current tailings management practices by comparing the geochemistry and mineralogy of tailings and the chemistry of seepage water from three Australian case studies in the context of geology, mineral processing and climate. Some alternative methods of tailings management are also reviewed and it is concluded that a proactive multi-disciplinary approach is needed with respect to tailings management, based on a novel integrated research framework.CITATION:Edraki, M, Forsyth, B, Baumgartl, T and Bradshaw, D, 2012. Geochemistry of tailings and seepage from three tailings storage facilities in Australia - Uncapped, capped and active tailings, in Proceedings Life-of-Mine 2012 , pp 269-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

Understanding multiphase particulate systems is essential for the further advancement of mineral processing technology. Characterisation, analysis, and simulation of these complex systems provide a fundamental basis for the development of improved mineral processing technology. One of the more recent tools that can be used to help provide a foundation for improved mineral processing technology is high resolution cone beam X-ray micro computed tomography (CT). During the past ten years point-projection X-ray micro CT systems have been used for 3D visualisation and quantitative analysis of multiphase particulate systems. Analysis of packed particle beds containing as many as 30 000 particles can be accomplished in less than three hours with special software to establish the 3D characteristics of each particle in the population and the spatial organisation of the packed particle bed. Now, due to advances in X-ray optics, the resolution afforded with point-projection micro CT systems has been improved by at least an order of magnitude using a lens-based X-ray micro CT system. The development of software tools for the 3D characterisation, analysis, and simulation of packed particle beds using high resolution X-ray micro tomography (HRXMT) is discussed including examples of application in the areas of comminution (particle damage and preferential grain boundary fracture), exposure/liberation analysis (liberation-limited separation efficiency, including coal washability), and filtration/heap leaching (pore network structure of packed particle beds and simulated flow using the LB method of computational fluid dynamics).

Sep 13, 2010

Statistics on the imports of industrial minerals into the EECshow that the traded volume in 1987 is approximately 23 million tonnes.The following table documents the imported quantities on the most important industrial minerals.

Jan 1, 1989

By L Salvestro

Ventilation on demand (VOD) has been demonstrated to significantly reduce operating costs for ventilation fans, by reducing fan output to meet demand. The most effective method for reducing operating costs is to use variable speed drives to adjust the speed of ventilation fans as required – this achieves significantly larger power savings that damper or vane control alone.However, this mode of control will significantly increase the number of speed cycles the ventilation fans will experience. Fabricated impellers have a limited number of start stop cycles based on the materials and method of construction, and the operating stresses due to centrifugal forces. This means that fans experiencing constant or regular speed changes will experience a reduced fatiguelife compared with fans that are run at constant speed.The fatigue life of fans operated under various speeds using VOD is difficult to predict, as it is dependent on the magnitude of speed changes, and the frequency, which will be varied to meet demand. It is important to be able to estimate remaining fatigue life to assist in maintenance planning and avoid unplanned maintenance activities.This paper will review extensive VOD data on fan operating conditions from two primary mine ventilation fans. This paper will demonstrate how this data can be used to calculate accumulated fatigue and predict the remaining fatigue life, and how this compares with fixed speed or non-VOD controlled fans.The increased maintenance costs for the impellers will also be estimated, and compared to the operating cost savings using VOD, to determine if the savings outweigh the additional maintenance costs.

Oct 12, 2022

Probably no other country or coutinent has so many rich deposits of various different minerals as Australia. Long ago in the days of my boyhood in the old land the marvellous discoveries of high percentage copper at Burra Burra, Peak Downs, Yudanamutana, and other mines, was one of the principal themes of conversation in mining circles whilst the specimens of malachite, azurite, etc, brought home by returning miners were the admiration of my boyish eyes.Later on the WalIaroo and Moonta mines still further helped to heighten the reputation of Australia as a copper-producing country. During the 21 years that the writer has been resident in the Australian colonies, other mineral deposits have sprung into prominence, and with a Mount Bischoff for tin, a Broken Hill for silver and lead, and a Mount Morgan for gold, Australia can now boast that it has had within its borders the leading mines of the world, in four different minerals, and still at least maintains that pre-eminence in gold, silver and tin. To the miner from the old land, Australian mining is at first a revelation and a wonder. In very many instances he looks in vain for the regular strike and dip of the veins he has been accustomed to'Smooth hanging and foot alls are often wanting. 'Huge irregular deposits, like those mentioned above, viz., Burra Burra, Mount Bischoff, Broken Hill, and Mount Morgan, are mysteries that will take time to fathom-if, indeed, they are ever thoroughly understood and in many a smaller deposit there is much to interest alike the professor in the college and the miner in the mine.

A clear understanding of the meanings of terms is important when discussing a project. Whether it is a submission, an investment study, a feasibility study, an environmental impact statement, an estimate, a tender, a contract, or a close-out.report, the need for all parties involved to understand what is under discussion or what has been written is paramount. The clarity of definition and the level of understanding can affect the outcome of the project. It is vital that all parties know what is wanted, what is expected, and what it will cost. This paper draws attention to some of the problems that beset many projects, clients, project managers and contractors, and it is hoped that its presentation will encourage us to pay more attention to defining what it is that is required. Ultimately we should all be the richer for having defined and understood the requirements at the beginning rather than at the end.

Jan 1, 1990

By P Stoker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Mining and exploration properties have a unique set of technical risks. Privately-owned companies considering investing in the resources sector can optimise their investment decisions by adopting a systematic technical assessment of acquisition assets, similar to the approach commonly adopted by public financial institutions and publicly-listed companies.Technical due diligence provides a process to identify key geological, mining, geotechnical, metallurgical, environmental and social risks and opportunities and determine the most likely business case and valuation of assets. Technical due diligence is commonly carried out in parallel with legal, commercial and financial due diligence, often involving the acquirer, to maximise the understanding of the investment.There are significant advantages in investors conducting a comprehensive technical due diligence, which typically involves site visits and project assessment to international standards by an independent, multidisciplinary team of experts. The outcomes provide the opportunity for the investor to make early, informed decisions and to understand and manage risks.Technical due diligence may be carried out at several stages: when considering and weighing up a number of investment options, prior to and during a transaction or immediately post-transaction. In the first stage, the outcomes will inform the choice of investment and, more particularly, whether there are any fundamental flaws in the projects being considered. In the second stage, due diligence outcomes can inform the level of investment and approach to risk management and planning. In the third stage, risks and opportunities can be investigated in more detail, allowing the investor to consider the best options to reduce risk and maximise the benefit of the investment.This paper presents a summary of the technical due diligence assessment process, its benefits to investors, common risks in mining and exploration projects known to cause mining asset write-downs and principal technical due diligence approaches.CITATION:Keogh, A, Stoker, P and Thomas, M, 2015. Benefits of due diligence in private equity mining investments – maximising value and unearthing common risks , in Proceedings PACRIM 2015 Congress, pp 115–126 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Riley S

Many regulatory bodies have, or are considering, guidelines that require rehabilitated mine spoils to be erosionally stable (satisfying quantitative limits) over specified design lifetimes. One of the problems facing the industry is that many of the computer models used for erosion assessment were developed for agricultural applications and are unable to predict the change in the shape of engineered landforms over extended periods of time. In particular, they cannot predict where valleys and gullies will develop in the landforms and how big or deep they will be. Furthermore, many existing models require considerable skill to use. A computer model (SIBERIA) developed by the first author, able to model this valley and gully development over long design lifetimes, and which is directly based on digital terrain maps is discussed here. Proposed rehabilitation strategies for waste rock dumps at Ranger Uranium Mine as assessed with SIBERIA are discussed. New features of SIBERIA of interest to the mining industry include the spatial distribution of erosion, deposition and gully development, and various measures of the quantitative risk of failure. A collaborative project with the Queensland Coal Association, involving the first author, aims to deliver these capabilities to the coal industry in a user-friendly package. The objective is the cost-effective rehabilitation of strip mines. Some preliminary results from this project are presented.

Jan 1, 1994