Search Documents

THIS has been a much-neglected branch of engineering. With the majority of industries labour is the chief item of trouble and expense. Anything that will reduce trouble and increase efficiency is well worth considering. It is only of recent years that any attempt has been made on a scientific basis to improve conditions sporadic attempts having been made from time to time, privately and by law. Some have been successful, others unsuccessful not necessarily the fault of those who initiated the ideas, though naturally mistakes were made in some cases for want of experience, but those whom it was desired to benefit were not always prepared for the change, and by their distrust hampered schemes instead of assisting them.Man power is generally more expensive than machinery, though there are exceptions, such as when a small amount of work has to be done in a place where machinery does not exist, and it would not pay to instal any or where labour is cheap, and skilled workmen are scarce as in some tropical countries. When machinery is first introduced it generally causes the suspicion that it will deprive men of their work. It may cause men to vary the conditions of their work, and in some individual cases, when men are unable to conform to changed circumstances it may result in a certain amount of hardship; but, after all, the less competent must not hold back progress for the general good. Besides, changes as a rule do not take place suddenly, so old hands can generally find work at their particular calling 'till nature requires them to retire. In cases where men take to machinery, they not only find that they are relieved of the...

Jan 1, 1918

By M Erskine, R Mills

This paper approaches tailings dam risk management from the perspective of how other high hazard industries approach the management of their catastrophic event risks, with the aim to provide recommendations from these learnings for the industry to adopt.

Jul 1, 2021

Coal mining legislation makes frequent reference to æSafety Management SystemsÆ but there is a chronic shortage of useful guidance material as to how these might be applied to hazardous exposures. Several studies have indicated that for each death that is reported as a result of an industrial æaccidentÆ, there are five deaths that caused by occupational exposures. Because the deaths from occupational exposures do not occur on site and often well after employment has ceased, they are generally unreported. Improved access to mortality data from coroners, the Australian Institute of Health and Welfare and superannuation service providers (early claims from death and total permanent disability), has given rise to some analysis of death and disability data that provides evidence that there are emerging opportunities to develop and improve safety management systems for hazardous occupational exposures. Issues explored include how safety management systems might be developed in relation to dusts and chemicals and other hazardous exposures to ensure the risk of disorders with long latency periods are reliably assessed and the exposures effectively managed. The current standards and guidelines which refer to safety management systems in general or to management of exposure related hazards are examined. Many standards are based on dose-response studies that provide for an acceptable percentage of workers to suffer adverse health outcomes. An alternative management system might be to apply dose-response relations to health surveillance to identify æat riskÆ individuals and effectively manage health and related safety risk at an early stage.

Jan 1, 2005

By L Edwards, M Haest, D Mittrup

The focus in the iron ore industry has shifted from increasing production volumes with less regard for cost, to efficient production of quality tonnes. BHP Billiton iron ore geoscience and exploration has embedded infrared spectroscopic sensing of drill hole samples to help meet this challenge.Infrared spectroscopy is delivering mineral predictions that are used for (automated) geology logging and modelling. The spectra are processed together with other available data sets to predict geometallurgical and geotechnical variables that include lump per cent and uniaxial compressive strength.Trials are ongoing to test the benefit of infrared spectroscopy during mining, including the analysis of grade control samples and remote sensing of mine faces. Results show great benefits in the fields of short-term geology modelling, better understanding of material (handling) properties, identification of geotechnical risk areas and high resolution ore-waste delineation.These trials are bringing BHP Billiton iron ore closer to its ultimate goal of having infrared spectroscopic data collected across the mining value chain. Once such data are available everywhere, regression models can be trained at one point (eg iron grade model trained on exploration samples) and be applied elsewhere (eg iron grade predicted on mine faces). Such predictive analytics will enable not only high precision mining, but also provide maximum time to tailor plant design to the ore in the ground, based on learnings from ores processed in other plants. This will improve planning outputs that will eventually increase mining efficiency, processing capability and product quality.CITATION:Haest, M, Mittrup, D and Edwards, L, 2017. Infrared spectroscopy in BHP Billiton iron ore with a focus on in-mine infrared sensing, in Proceedings Iron Ore 2017, pp 549–556 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By K Blay, C McCamley, P Petrucci

The Newmont Boddington Gold (NBG) processing plant was designed for 35Mt/y with ball mills expected to deliver a combined new mill feed rate of 4837 tonnes/hr. Since beginning commercial production in late 2009, the plant has steadily increased throughput to meet design capacity in 2014 and reached 37 Mt/y in 2015. Through improved efficiencies, changes to the milling circuit have taken place since commissioning to take the plant beyond its design to an actual throughput of 39.0 Mt in 2017 and a budgeted throughput of 39.4 Mt/y this year.The NBG milling circuit has four parallel ball mills, each consisting of a 7.9 x 13.4 m ball mill with twin 7.5 MW fixed speed motors in closed circuit with twelve 650 mm cyclones. Each mill is fed by two wet screens with the undersize gravitating to a mill discharge hopper where it is combined with the ball mill discharge and pumped to hydrocyclones for classification. The cyclone underflow is re-ground to a target P80 of 150 µm.This paper will focus on process improvements made to the NBG milling circuit which include cyclone reconfiguration, fine screen panel redesign, implementation of an expert control system, mill power draw increase and grinding media changes to take NBG beyond its design throughput.CITATION:McCamley, C, Petrucci, P and Blay, K, 2018. Going beyond design at Newmont Boddington Gold, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 497–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By B Belle, M Biffi

Cooling of coal mines in the Bowen Basin, characterised by steep geothermal gradient, is presently achieved mostly through rental surface bulk air cooling in summer months. This paper argues that future mines will be required to focus their cooling resources more intensively to manage a challenging thermal environment where virgin coal temperatures of over 50¦C at a depth of 500 m are expected. Currently, mine cooling systems are employed to maintain the wet bulb temperatures (WBT) to below 27¦C at which point the risks of heat stroke or other heat-related issues are manageable. The capacities of these systems are in the range of 6 MWR to 10 MWR. The relationship between high working temperature environments and injury frequency rates is well established. Therefore, provision of appropriate cooling strategies and understanding their optimum performance and suitability are important to Australian coal mines of the future. This paper evaluates the underground temperature profiles of deep, gassy coal mines with propensity for spontaneous combustion and proposes the long-term cooling pathways to effectively manage thermal hazards. Thermodynamic modelling is performed on a longwall face and includes air leakage effects from goaf streams at various locations along the longwall face. The strategy summarises the application of underground bulk air cooling, chilled water sprays on the shearer and the resulting temperature profiles. Considering the new mining projects planned for the Bowen Basin region, a review of implementable cooling strategies such as mid-gate mobile bulk air coolers (BACs), spot coolers, underground bulk air cooling and the use of chilled water to enhance the positional efficiency of cooling plants, are discussed in this paper. Finally, the comparison of ærentalÆ versus æownershipÆ of cooling plants is analysed as part of long-term cooling strategies.CITATION:Belle, B and Biffi, M, 2013. Cooling pathways for deep Australian longwall coal mines of the future, in Proceedings The Australian Mine Ventilation Conference , pp 223-236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Bell I. F

In 1985, ZC Mines (now Pasminco South) had been unprofitable for some years due to a combination of high operating costs, low metal prices, low head grade and an aging and inadequate mining infrastructure. However, the resource of metal in the ground was still of world class, even after some 80 years of mining. A major study, which was to be of two years duration, was therefore commenced to establish a practical and profitable long term mining strategy and to cost the infrastructure options needed for its support and thus form the justification for a capital expenditure program to take the mine profitably into the 21st century and its second century of operation. This paper discusses the rationale behind the methodology adopted and the nature of the results achieved in one aspect of the study - the determination of the mineable resource and the relationship between the head grade/quantity of the economically mineable resource and the variables of cut-off grade, cost structure, annual production rate and metal prices/exchange rates. The basis of the study was the designing of some 5000 scopes to mine out the entire resource for a range of cut- off grades and the assembly of the detailed physical data thus obtained in a stope-by-stope data base for financial and other analysis. Those scopes which were shown to be economically mineable were then scheduled for two optimum annual production/cut-off grade/metal price combinations to provide life-of-mine cost and value of production cash flows.

Jan 1, 1992

By D Baas, J Le, R Braun, R Chandramohan, K Hollis, G Lane

The Phu Kham Copper-Gold Operation (Phu Kham) is located in northern Laos, approximately 140 kilometres from the capital, Vientiane. The operation is a producing asset for Australian-based copper and gold producer, PanAust Limited (PanAust) and is operated by Lao-registered company, Phu Bia Mining Limited (Phu Bia Mining). PanAust holds a 90 % interest in Phu Bia Mining. The Government of Laos owns the remaining 10 %.The Phu Kham Operation has recently undergone a series of process improvements to treat the anticipated competent ores scheduled for 2017 and 2018. The operation’s comminution circuit, which comprises a semi-autogenous (SAG) mill and two ball mills, each with 13 megawatts (MW) of installed power, was expected to be SAG mill limited when treating competent basement rock. Ausenco Services Pty Ltd (Ausenco), was engaged to help optimise and enhance the productivity of the Phu Kham comminution circuit over an eight-month period. The work involved participating in and overseeing the redesign of the SAG mill liner systems and developing operational strategies for maximising throughput through to the end of mine life. Ausenco’s comminution optimisation tool, Ausgrind, was used to benchmark and analyse plant data with empirical models, predict circuit performance for varying ore characteristics and evaluate liner wear and predict the life for varying operating parameters. Variances between the actual and the predicted values were assessed in detail to identify missed opportunities, and guiding operating parameters were redefined to maximise throughput and productivity. In combination with the redesigned liner system, optimised process controls for varying ore competencies, and improved operational practices and troubleshooting strategies, increased Phu Kham overall production, exceeding the milling capacity when treating competent ores. CITATION:Chandramohan, R, Braun, R, Lane, G, Hollis, K, Le, J and Baas, D, 2018. SAG mill optimisation and increasing throughput at the Phu Kham Copper-Gold Operation – a success story, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 113–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By K J. Davey, J T. Woodcock

Australian steelmakers produce up to 30 000 t/yr of electric arc furnace (EAF) dust. Current disposal techniques include sending EAF dust to landfill, stockpiling, and paying zinc smelters or registered waste removalists/processors to take the dust. Many of the complex overseas pyrometallurgical and hydrometallurgical treatment routes cited in the literature are not considered economic. Governmental, environmental and social pressures on producers to consider more sustainable disposal options are mounting, and there is now a strong push to consider recovering potentially valuable or recyclable components, such as zinc and iron units, from EAF dust. As well, there remain strong economic drivers for producers to find lower cost disposal solutions. Characterisation studies undertaken at CSIRO Minerals have revealed important physical differences in the nature of the zinc- and iron-bearing phases contained in domestic EAF dusts. These differences have been exploited using simple and cheap mineral processing techniques such as water washing, wet cycloning and wet magnetic separation. This has allowed a significant upgrade in the zinc content of EAF dust to be achieved, together with a reduction in the levels of key smelter penalty elements, such as chlorides and fluorides. The zinc-rich portion of the dust is now a more attractive smelter feed while the iron-rich part of the dust could potentially be briquetted or pelletised with a reductant and recycled to recover iron, and thus close the loop on dust processing. The basis of the separations tested together with laboratory results from several Australian dust samples are presented and discussed in this paper.

Jan 1, 2006

THE area dealt with in this paper is included within a radius of about 3 miles of the Poimena township. Several thousand tons of tin have been won from this field, and probably £200,000 spent in exploiting it.PREVIOUS LITERATUREThe field has been reported on by Government geologists on four occasions and several ,articles on it have appeared in the mining journals. The work done by Government geologists is summarized below:-"Report on the Blue Tier Tin Mining District and its Tin Deposits", 1886.Speaking of the tin-ore occurrences, this paper states:-"In the primary granite the lodes of tin ore occur, also dykes and belts of more recently obtruded porphyries. The really valuable metalliferous deposits may be classified as follows :-1. Lodes (of which the Lottah mine is typical).2. Dykes- (a) Indurated or hard (as shown by the formations at the Anchor and Cream Creek mines). (b) Soft (eg Hayley's Lease).

Jan 1, 1912

The ready solubility of gold in dilute aqueous solutions of the cyanides of the alkalies or alkaline earths provides a convenient method for the separation of the precious metal -from the large surplus of associated materia1. The finely ground ore is pulped with a weak solution of cyanide, agitated to dissolve the gold, filtered and washed. The lowgrade filtrate is then clarified and the gold precipitated by some electronegative agent, the most usual being finely divided zinc or zinc dust. The slight precipitate is collectedon some form of filter coated with a filter aid, the filter cake being then known as "gold slime".A typical analysis of this slime is given in Table 1.

Jan 1, 1956

By S Hanrahan, S McLaughlin

A case study is presented that details the safety journey at a North American project involving two major contracts: a 1000 m shaft recovery and rehabilitation, and the development of a drainage gallery in a large open pit operation. In the early stages of the contracts, there were a number of incidents that created tension between the owner and contractor, which resulted in the contractor being placed on a final warning with almost imminent potential termination. As a result of this, it was agreed to initiate a focused safety recovery plan as a ‘last chance’.Over a period of two years, the engagement and consequent performance of the contractor was turned around, steadily working to set it up for success such that in one of the contract work areas, a record of ‘one year LTI (lost time injury) free’ was achieved. The journey involved the owner and the contractor teams working cohesively to educate all parties in the safety requirements and, most importantly, providing the context and understanding for certain requirements being put in place. Early on in the process, it was recognised that the owner team unknowingly was an impediment in that they did not fully understand the safety requirements and so was not able to lead the way for the contractor effectively. The journey to rectify the situation was supported and followed up by focused engagement with the project team, which generated a progressive improvement in a very challenging environment.In particular, the contractor turnaround was significant and of enough value for the contractor to ultimately export some of the safety systems from this site to other contract sites. This demonstrated the ultimate benefit of the contractor understanding and buying into a safety culture and system.CITATION:Hanrahan, S and McLaughlin, S, 2016. Winning the safety battle, in Proceedings International Mine Management Conference, pp 181-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By B Wentzinger, Y Keulemans

This paper presents the results of a field study designed to assess the impact of vane rotation speed on the estimated undrained strength for two Australian bauxite tailings storage facilities. The vane test results are assessed against cone penetration and dissipation tests results to identify if partial drainage may be an issue. An innovative tool capable of measuring pore pressures during vane shear testing, the Piezovane™, is introduced as an improvement over the standard field vane to assess drainage conditions in real-time.

Jul 1, 2021

G. R. Compton (Gold Mines of Kalgoorlie (Australia) Ltd., Fimiston, W. A.) : In congratulating Mr. Hooker upon his resume of Mr Parry's paper I have in mind the fact that he carried out the research into pipe pressures. Hydraulic filling as practised in Kalgoorlie has created world wide interest, with these pressures and percolation being vital points.Early in the 1950s, representatives of the Kolar field were conduGted over the local mines where stopes at depths below 2,000 ft were being filled. The problems of pipe pressures were their main consideration since depths of up to 10,000 ft were envisaged.Mr Krishnaiah and Mr Murthy from the same field are with us today and perhaps we may hear of their experiences with depths of 6,000 ft and long lateral lines.J. Holly (Lake View and Star Ltd., Fimiston, W.A.): There is one phase, which I would like to mention myself, that has been very evident in Kalgoorlie operations. That is, we do not get the percolation properties that are obtained on many other fields in the world, and our tendency here has been to assess the quality of our fill more by its settling rate, i.e. the rate at which we can draw off clear water at the surface of the filling levels, rather than the rate that this water percolates down through the fill before it consolidates.We are tending now to measure the quality of our fill as a settling rate rather than as a percolation rate.Americans talk about percolation rates being the important property: If anyone has any experience on operating with fills with different percolation rates, I think their views would be very interesting to the meeting art this stage. Mr ...

Jan 1, 1965

By N Anderson

With traditional grade control processes, geological models are created by geologists at the completion of the data collection stage and wireframe construction is closed off at a set date to allow for time to complete the estimation process. Any issues identified at earlier stages or the addition of new data requires the estimation process to be started again. Alternative interpretations are explored only if time allows and often in a limited fashion. An alternative workflow has been developed at the Waihi Underground Gold Mine utilising Leapfrog Edge and Seequent Central. Geological and grade control models are created, dynamically linked, and saved as separate branches. A project geologist is able to work on the grade control model and a mine geologist on the geological model simultaneously. This allows for a non-linear modelling workflow with continual review and feedback. The introduction of new data can occur right up to the model due date, with data collection, validation, alternate interpretation, and review happening incrementally. Models are categorised and stored in Seequent Central according to project status. An approved version of the geological model and grade control estimate are uploaded at the time of release and transparently capture all data used at a point in time, as well as the review process. Dynamically updating models for grade control has reduced turnaround time while increasing accuracy and quality. Estimates of individual domains are vastly improved from being able to rapidly evaluate the effects of model parameter changes in real time and 3D. Development and stope design directly benefit from these streamlined processes, with higher quality, timely production occurring as a result.

Mar 22, 2022

The importance of timbering, not only from a financial point of view but from an actual mining point of view, is so often overlooked or slightly glossed over by the average expert and investor, that I have thought it would prove interesting to go into the matter and to invite discussion upon the subject. We will first take small veins, or reefs as they are termed in some mining countries; and by small veins it is intended to denote fissures from a few inches to three feet. The ore body is supposed to be confined within well defined walls free from gangue matter, unless the casing can be defined as such. Now, if the walls are smooth and moderately hard, no timbering is required other than the stulls, which are braced from wall to wall in order to form platforms or stages to stope from. Should the reef from wall to wall prove payable, or should the vein be of a character to prohibit cleaning or sorting; and it be determined to send the whole of the stone to the, reduction works, the stuUs should be left in place until the section or block of ground is worked out, in order that if a weak spot in the walls (especially the hanging) occur, it would be possible, without any particularly extra expense or difficulty often times accompanied by danger to brace and secure the slabs. After the block became entirely stoped, it would pay where labour was cheap to remove the majority of timbers to stull another section.

Jan 1, 1901

By E Widzyk-Capehart, C Hölck Teuber, S Steffen, V Rivero, O Fredes, E Sanchez, I Pedemonte, N Gonzalez

This paper summarises the research, development and initial application of a sensing platform that has the potential to monitor subsurface deformations, pore pressure and other variables simultaneously to gain a better understanding of rock mass behaviour. The platform is based on Networked Smart Markers (NSMs) devices, which, with their ability for wireless communication between individual sensors and the possibility of real-time data acquisition and processing, will assist in the development of predictive tools to better assess rock mass behaviour.A good opportunity to implement this technology is in the specific application of transitioning from an open pit mine to an underground caving operation. One of the key elements to maintaining the mining business during such a transition is having a good understanding of the unique geotechnical conditions of mutual influence created during the open pit to underground interaction. The knowledge acquisition will require the implementation of a robust platform for geotechnical monitoring, which could be enhanced by incorporating the NSMs. The integration of sensors within the NSMs would enable the collection of additional data about rock mass behaviour (ie caving propagation and crown pillar fracturing), which could be used to improve the management of mining operations and, specifically, allow the development of reliable predictive tools based on the data collected.CITATION:Widzyk-Capehart, E, Hölck Teuber, C, Fredes, O, Rivero, V, Sanchez, E, Pedemonte, I, Gonzalez, N and Steffen, S, 2016. Understanding rock mass behaviour through the development of an integrated sensing platform, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 275–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By G Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified low factor-of-safety due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the low factor-of-safety area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model. Electronic detonators and blast initiation systems were combined with advanced blast vibration modelling software to produce optimal timing sequences with predictable vibration outcomes. Although minimising vibration was the primary focus, blasting induced frequency was also a concern for the project team and therefore initiation sequencing was optimised to also avoid undesirable frequencies. Minor variations in ground factors (vibration transmission and attenuation) were noted, and therefore justified the inclusion of regular signature holes which allowed continual vibration model updates. Blasting results produced vibration and frequency measurements within allowable limits and closely resembled the predictive model. These positive results were achievable through the combination of electronic detonators, advanced modelling software and good onsite practices by engineering and on-bench teams alike. This project will remain ongoing as the pit progresses to deeper benches, and therefore the same methodology will be applied; quality and continual data collection, the use of electronic detonators, and optimisation via advanced vibration and frequency modelling software. CITATION:Wyartt, G, 2018. Vibration control blasting for low stability final walls, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 504–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Pilon CG, Deakin RC

It is proposed that a waste rock dump be constructed on slopes consisting of soft colluvium and weathered Chim Formation mudstone at the Porgera Gold Mine, in Enga Province, Papua New Guinea (PNG). Geolog- ical, geomorphological and geophysical investigations were conducted in support of geotechnical studies to assess the physical character of the 6km2 site. Geomorphological studies focused on the extent and nature of colluvium cover and landslide activity. Detailed ground traverse mapping resulted in classification and delineation of eight terrains and seven material types. Seismic refraction and resistivity profiling, combined with drilling, provided subsurface data. Results were presented as standard profiles, coloured contoured sections and plans. Subsurface features, including deep colluvial channels, buried cliffs, slump blocks and buried alluvial channels, were identified. Results of the combined investigations allowed designers to model the colluvium/ bedrock surface and identify critical areas of deep, mobile colluvium and weak bedrock. A design approach was developed which accounted for the morphology of landslide systems and distribution of colluvium types.

Jan 1, 1991

Fast Adsorption Phenomena at Air/Liquid Interfaces

Sep 13, 2010