Search Documents

The selection of the best comminution circuit for the preparation of concentration feed is a compromise based on economics, energy efficiency, labour costs, steel consumption, availability and other factors specific to each case. It is postulated that the selection must be a choice of one of the eight basic comminution circuits which can be divided into two basic groups, (1) autogenous or semi-autogenous primary mills with or without a secondary grinding stage and (2) fine crushing usually in cone crushers followed by a rod mill-ball mill circuit or a single stage ball mill circuit. The accuracy of selection may be improved by pilot plant and laboratory tests which are described in this paper. For (1) above, testing includes media competency tests with standard impact crushing, grindability and abrasion tests followed by pilot plant tests. For (2) above, bench scale crushability, grindability and abrasion testing is available. It is suggested that, through these tests, it should be possible to eliminate all but one in each group of basic comminution circuits. Then engineering and economic studies should lead to the best comminution circuit for the specific requirement.

Jan 1, 1984

By R Munoz, R González, J Vallejos, A Delonca

In panel caving in underground mines, it is essential to characterise and monitor the stress and stability state of production level pillars to ensure the extraction of the mineralised ore column and the safety of workers. Pilar Norte is a sector in the El Teniente mine that forms a pillar between the undercut fronts of the adjacent Esmeralda and Reservas Norte sectors. It exists in a high-stress environment, which may induce damage to the rock mass production pillars. Generally, numerical models are calibrated using observed damage in galleries. This procedure does not discriminate between the structural condition and/or the blasting damage effects. This paper proposes a technique that uses borehole cameras to measure stress-induced damage. This has the advantage of being at the intact rock scale, meaning that the effect of geological structures is negligible and the blasting damage factor is eliminated. Comprehensive geotechnical characterisation and tomography monitoring has been undertaken at Pilar Norte to describe and determine the rock mass behaviour of the production pillars. By combining analytical, empirical and numerical models, a correlation between the measured overbreak recorded by the borehole cameras and the stress level of the pillar was developed. The methodology can be routinely applied to estimate the stress state in the production pillars.CITATION:González, R, Munoz, R, Vallejos, J and Delonca, A, 2016. Characterisation and monitoring of the stress state of production pillars at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J L. Mauk

 Broken Hills is an adularia-sericite epithermal Au-Ag deposit, hosted in flow-banded rhyolites and overlying rhyolitic pyroclastic rocks in the eastern Hauraki Goldfield. The 7.1 Ma deposit was the largest producer of gold in the eastern Hauraki Goldfield, and was one of very few economic deposits hosted in Pliocene rhyolites. This paper presents the results of a recent study in the upper levels of the deposit. Maps and cross-sections constrain structural and lithological relationships, and the lateral and vertical extent of a breccia pipe û the major feature of the upper levels.   Previous studies in the upper levels of Broken Hills have shown that gold and silver values are concentrated around and within a large breccia pipe, mined by a series of æcaveÆ stopes and in veins. Contour diagrams of Au-Ag data from channel samples indicate that the breccia pipe was a major fluid channel-way for mineralising solutions.   The breccia pipe deposits are part of the dynamic geothermal system that formed the Broken Hills ore bodies; they developed as a result of hydrothermal brecciation in areas of structural weakness within a rhyolite pyroclastic unit that overlies a massive rhyolite lava-flow unit. The main breccia pipe begins near the rhyolite/pyroclastic contact, having the shape of an inverted, inclined cone, and consists of silicified breccia, stringers of quartz, and irregular patches of clay-altered country rock. Smaller zones or pockets of hydrothermal eruption breccia are silicified and contain low grade gold in the matrix and in the adjacent silicified wall rocks.   Quartz has been classified according to its physical characteristics as seen in situ and hand specimens indicate that vein definition decreases upwards, perhaps as a result of changing lithological conditions and/or increasing proximity to the paleosurface. Hydrothermal quartz is widespread as veins and as a replacement mineral, or lining fractures and cavities and overgrowing rock fragments. Breccias contain vein quartz, but some quartz veins cross-cut breccias, indicating that vein and breccia formation was relatively synchronous and overlapped in time.   Disseminated gold-silver mineralisation is associated with vein quartz and silicic alteration of the wall rock within the breccia pipe. The auriferous zones are highly irregular and erratic, and sampling results show a wide range of gold-silver ratios, suggesting that highly volatile physiochemical conditions prevailed during mineralisation.

Jan 1, 2005

By E Ah Mu and C R Lilley, A D. Campbell

Cave propagation is a complex process due to interacting variables such as mine geometry, rock mass heterogeneity and complex structural networks and stress fields. The Ernest Henry sublevel cave (SLC) is directly below an open pit, which provided an opportunity to observe and measure rock mass failure as the cave initiated and propagated through the pit wall. This paper describes interaction between the open pit and SLC as well as rock mass failure mechanisms observed from the start of the SLC to surface breakthrough.Cave propagation and slope failure mechanisms were found to be governed by intermediate structures, while the cave shape was largely controlled by cave-scale faults. The open pit, production-level geometry and production draw strategy were also important factors for cave and subsidence growth. Cave propagation was episodic and asymmetric in shape due to the orientation and relative position of geological structures, combined with the effects of the increasing SLC geometry and drawdown from the underlying production levels. The precursors and failure mechanism of a 2.5 Mt wall collapse are also reviewed in detail.Cave growth was simulated using a 3D, non-linear, discontinuum finite element model coupled with Newtonian Cellular Automata. Model results are compared to field observations and monitoring data to determine the accuracy of forecasts and compared models versus actual rock mass response during cave propagation.CITATION:Campbell, A D, Ah Mu, E and Lilley, C R, 2016. Cave propagation and open pit interaction at the Ernest Henry Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A Castleden, G Cavanough, M Kochanek, J Cunningham

ROES« is a proposed new mining system for underground hard rock mines. Ore is accessed from within a shaft, which is located close to or within the stope, and pitched either vertical or within approximately 20 degrees of vertical. The shaft is designed to exclude personnel entry so production drilling and explosive placement is done using remotely controlled or automated machines. Routine remotely controlled survey of the shaft, stope back and broken rock within the stope is typically done following each blast. The survey may include excavation geometry, rock fragmentation and geotechnical characteristics. Blastholes are surveyed before placement of explosives. This provides mine operators and engineers with real-time data, allowing them to monitor production performance and risk factors so that they can make rapid changes as required. ROES« is designed to apply to open stoping or sublevel caving situations either in disseminated, geologically defined, thick tabular or narrow vein orebodies. The technologies developed for ROES« will also have potential applications to block caving operations to reduce the risk of frozen ore and poor fragmentation. In a typical sublevel open stope application, ROES« will reduce the amount of stope-associated development by about half and therefore will allow ore to be brought on-stream sooner and at significantly reduced cost. Other savings are expected to flow from the centralisation of mining activities and operational data, reduction in mining fleet, reduction in ventilation requirements, improved occupational safety and reduced mine complexity. CSIRO and Orica Mining Services are developing the required technology and AMIRA is seeking sponsorship for a project to trial the mining method. This paper details the ROES« method, expected benefits and applications and includes typical stope and mining block designs and design requirements.

Jan 1, 2008

By T Higuchi, L Lu

The quality of iron ore fines have been deteriorating, which has affected sinter quality and productivity adversely. New pretreatment and sintering technologies are therefore required to tackle the gradual change in the quality of iron ore fines. In the sintering process, iron ore fines are first granulated with fluxes such as limestone and coke breeze, and are then loaded and fired in a sinter machine. Sinter productivity and quality are heavily influenced by the reactions occurring in the sintering bed. Hence fundamental understanding of these high temperature properties of ores is urgently needed.Formation of initial sinter melt, penetration and assimilation of nucleus particles by the initial melt, and consolidation and final solidification of final sinter melt are believed to be the key sintering reactions. The assimilation and penetration phenomena have been studied separately in the literature with model particles and diffusion couples and are therefore difficult to relate to sinter quality. In addition, the effect of ore mineralogy has not been studied in detail.In this study, tablets consisting of coarse particles from various iron ore fines as nucleus particles and chemical reagents as adhering fines were made and fired under various sintering conditions to investigate the penetration and assimilation behaviour simultaneously. The degree of assimilation, pore structure, compressive strength of the resultant analogue sinters were evaluated and the relationship between sinter strength and ore characteristics was further discussed. The nucleus particles from Ores A and B were found to be more porous and assimilated more readily with sinter melt, resulting in a viscous melt and a macro-porous sinter structure. The nucleus particles from Ores C and D on the other hand, assimilated less readily with sinter melt, resulting in a fluid melt and a denser sinter structure. This is consistent with the results reported in the literature, suggesting that the present evaluation method can be utilised for studying sintering reactions and predicting sinter quality.CITATION:Higuchi, T and Lu, L, 2017. Evaluation of sintering behaviour based on ore characteristics, in Proceedings Iron Ore 2017, pp 303–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Dhar B. B, Gupta R. C

Grinding of iron ore is an essential step to utilise ore fines for pelletisation needed for DRI units. While preparing iron ore pellets for DRI production, the iron ore needs extensive grinding which is highly energy consuming step causing the process to become non-viable in some cases. In the present paper an attempt has been made to evaluate grinding performance of thermally treated ore compared to normal ore grinding. Such thermal pre-treatment has been found to reduce the energy requirement with lower consumption rate of grinding media. It has been observed that by applying thermal shock the ore is rendered weak with improved grindability. The stresses generated due to thermal treatment may extend existing micro-cracks in the ore and in some cases it may even nucleate fresh cracks. Experimental studies carried out on thermally treated hematitite ore reveals that the heating to 400¦C followed by water quenching can cause a reduction of 45 per cent in grinding energy. The paper gives the details of the experiment and the Results.

Jan 1, 1999

By A B. Christie, F P. Bierlein

Lode gold deposits of the Western and Eastern provinces, South Island, New Zealand , formed as a part of the Cordilleran-style tectonism during Tasman/Tahua and Rangitata orogenesis along the Paleozoic-middle Mesozoic southern Gondwanan margin. These deposits, hosted by lower grade greenschist facies sedimentary rock sequences of the Buller, Takaka, Torlesse, and Caples terranes, universally show geological features that are consistent with the orogenic gold deposit model, and genetic features are generally suggestive of a metamorphic origin, with the possible exception of a magmatic fluid source for the mineralisation at Sams Creek. However, ore fluid chemistry in Mesozoic deposits of the Eastern province, particularly the low concentration of non-aqueous volatiles and the very dilute nature of the fluids, is uncharacteristic of most orogenic gold deposits; this must be explained by either a unique fluid source or fluid type, which we believe unlikely, or an unrecognised significance of relatively rare gas-rich fluid inclusions in the deposits. Absolute age data for gold deposits in both provinces remain equivocal, thus hindering definition of the exact temporal relationship between ore formation and terrane accretion, regional metamorphism, and magmatic arc emplacement. Mercury and antimony occurrences in subgreenschist grade parts of the Haast Schist may target the upper levels of unrecognised orogenic gold deposits. If low-grade, high-tonnage intrusion-related gold systems occur on the South Island, then they are most likely to be discovered in association with the small molybdenite-, scheelite-, or cassiterite-bearing quartz stockworks spatially related to the Karamea and Median batholiths.

Jan 1, 2005

By M Grigorescu, J H. Hodgkinson, M Khanal

The mining industry often needs to operate in remote or climatically harsh locations. The industry has recently been forced to deal with extreme conditions including floods, heatwaves and droughts. As these are becoming progressively frequent occurrences, mines typically build ‘downtime’ into production schedules and expect to incur costs to manage the various risks arising from climate extremes. Importantly, many environmental conditions are becoming more extreme and consequently, risk management based on past data can become increasingly ineffective. Market and shareholder demand for fewer interruptions are another pressure on mines to avoid prolonged or frequent downtime. Hence, adaptation to climate is becoming an important strategic move for many companies, many of whom are using future climate scenarios and alternative risk evaluations.We present here a method that uses commonly available mine site data to assist decision-making for reducing vulnerability to sudden flood. The method, ‘climate-related adaptation from terrain evaluation results’ (CRATER), identifies a mine’s flood ‘hot-spots’ and presents them as a ‘traffic lights’ warning map. The process then requires a failure analysis process such as fault-tree analysis to identify both the cause of possible failures and a range of possible failure-avoidance adaptations. In the final stage, management can assess the most suitable option for the mine, based on the availability of capital such as time, facilities, labour and money in addition to social acceptability of the options. CRATER has been tested in an open cut mine environment and is now being further developed to identify how subsidence over underground mines may impact on flooding and ponding over the mining life cycle (CRATER II). Further work is continuing to test larger and more complex mine landscapes to deliver a method to extract more knowledge from existing data.CITATION:Hodgkinson, J H, Grigorescu, M and Khanal, M, 2016. Reducing mine site extreme rainfall vulnerability using climate-related adaptation from terrain evaluation results, in Proceedings International Mine Management Conference, pp 187-200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By W Polkowski, M Tangstad, M Wallin, J Jiao

Fe-26Si-9B (wt per cent) alloy has been identified as a potential high-temperature phase change material (PCM) due to its attractive properties, such as its high latent heat of fusion and low volumetric change during solid/liquid transition. For the successful utilisation of this alloy into thermal energy storage (TES) systems, the development of a cost-effective production method is essential. Presently, the Fe-26Si-9B alloy is produced by mixing FeSi alloys with either pure boron element or FeB alloys. However, the use of pure boron is financially prohibitive, and the carbothermic reduction results in high greenhouse gas emissions and high energy consumption in the production of FeB alloys. In this regard, our study proposes a silicothermic reduction method to produce Fe-26Si-9B PCM by using FeSi alloys and B2O3-based oxides. Accordingly, the influence of various parameters on the production process was investigated, including operating temperature, holding time, B2O3 content in the added oxides, and initial Slag/Metal (S/M) ratio. Based on the experimental results, the optimal parameters for producing FeSiB alloys with over 9 wt per cent boron were determined. Consequently, it was documented that the FeSi alloys and the added oxides enriched with 50– 65 wt per cent B2O3 should be subjected to temperatures ranging from 1550–1650°C, maintain an initial S/M ratio exceeding 1, and ensure a holding duration beyond 1 hr. Moreover, the energy consumption of this process was estimated to be ~1.86 MWh/t metal and the mass loss was lower than 7 per cent. Therefore, silicothermic reduction offers a sustainable approach for producing FeSiB alloys with a boron content above 9 wt per cent.

Jun 19, 2024

EARLY in 1911 the Public Service Board of New South Wales suggested the advisability of inaugurating a School of Mines at Broken Hill, arid made inquiries to determine how such an institution should be conducted. He, the author, believed the Board, as a result of the inquiries, was in favour of the project being worked in conjunction with the Technical College, and hoped to be ready to receive students at the commencement of 1912. That the inauguration has not yet taken place is probably due to the vast amount of consideration and preparation that a new departure of the sort would require. At the present time New South Wales or, to speak more broadly under the same denunciation, Australia is not at all suitably catering for the technical training of young men to provide the increasing demand for officers to work the valuable mines within its territory...

Jan 1, 1912

New Celebration Gold Mine is located 35 km SE of Kalgoorlie, Western Australia, in the Archaean Kalgoorlie-St Ives Greenstone belt. The leases total 119 sq kms and arepart of a joint venture between Newmont Australia Ltd (as manager) and Mt Martin Gold Mines N.L. Mining commenced in August, 1986 and is now producing over 115,000 ounces of gold per annum. A variety of gold mineralisation styles with a total resource of 23.5 million tonnes at 2.19g/t are associated with shear zones at New Celebration. Gold production is co-ordinated from 7 open pits with others planned to com- mence soon. A large scale underground trial mining operation has com- menced with a decline on the hanging wall of the main producing orebody, Hampton Boulder. Millfeed produced is classified on the stockpile according to grade and metallurgical performance and blended tomaximise throughput while main- taining grade through a CIL treatment plant currently operating at 1.7 million tonnes per year.

Jan 1, 1991

By J Folwell, G Phillips, F Gassner

Geomembranes selected for various applications often start with considering target properties developed by industry organisations such as Geosynthetic Research Institute (GRI), and test methods developed by ASTM and other Standards organisations The geomembrane types are typically, initially selected based on manufacturers recommendations and chemical resistance data from the manufacturer or industry knowledge. Geomembranes considered for this project included materials with material properties that exceeded the minimum target values of various test methods. The difficulty is in selecting which parameters are most important for a particular application and also what service life can be expected for the geomembrane under various chemical and environmental exposure conditions. Accelerated aging testing of candidate geomembranes in simulated exposure conditions can be useful to select the preferred geomembrane and predict the service life of the geomembrane under different exposure conditions. The exposure conditions of immersion in acidic tailings liquor, splash zone and freeboard zone were considered for evaporation ponds on a site with significant heat and UV radiation. Candidate geomembranes considered a range of different types of polyethylene liners. The results of the accelerated aging testing have allowed the selection of the geomembrane for the range of exposure conditions and evaluation of the expected service life of the geomembrane.

Jul 1, 2021

By L Bartsch, M Kelahan, E Wingate, J-S David

The use of column flotation cells for recovery of phosphate is becoming more common practice in certain parts of the world (Brazil, Russia) where igneous phosphate ores are processed. Igneous phosphates are generally finer grained (< 200µm) than some of the traditional sedimentary phosphates (<400µm). Australian phosphate from the Georgina basin is sedimentary, but has a much finer grain size (typically < 106µm) than similar deposits in North Africa and the USA.In 2013, Arianne Phosphate completed a bankable feasibility study for the development of their igneous phosphate deposit at the Lac a Paul site in Quebec. Initially, lab test work and bench scale piloting indicated that using traditional mechanical flotation would be able to produce adequate concentrate grade and an economic level of recovery, but would necessitate the installation of a complex and operationally challenging flotation circuit. Later pilot plant testing using column cells resulted in a significant reduction in process complexity and facilitated the processing of the -20µm ore fraction which resulted in a 10% increase in P2O5 recovery and a 5% increase in concentrate grade %P2O5.Flotation column testing achieved a concentrate grade of 38.6% P2O5 at a P2O5 recovery of 90%. Using a mechanical flotation cell circuit, the concentrate grade was 36.4% P2O5 with a P2O5 recovery of only 78.8%. A noticeable feature of the testing was the simplicity of the column flotation circuit configuration (Rougher + 2 stages of cleaning + Cleaner Scavenger) compared to the mechanical flotation cell circuit (Rougher + Scavenger + 3 stages of cleaning).The financial benefit for this case study was estimated using a sales price of US$ 195/t FOB for a 38.6% P2O5 product, and an assumed cost of production of US$ 95/t, the netback price is calculated at US$100/t. For a daily milling rate of 55,000t/d, the improved flotation performance provides additional concentrate production of 1,203t/d. Using the netback price calculated above, this calculates to additional gross profit of US$ 120,260/d.Annualised, this equals US$ 40.7 million in additional revenue for a similar or reduced CAPEX.The use of column flotation on fine grained phosphate ore types often requires fine grinding and desliming to liberate the phosphate value, such as the Australian sedimentary phosphate ores. This may enable the development of deposits previously regarded as uneconomic.This paper discusses the potential benefits available to operators, and developers of new projects, for the use of column flotation cells in their metallurgical circuits as assessed by an engineering company.CITATION:Wingate, E, Kelahan, M, David, J-S and Bartsch, L, 2015. Does it make cent$ to use flotation columns for phosphate beneficiation?, in Proceedings MetPlant 2015, pp 353–365 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

The Wainui Mill was conceived as a 60 - 90 t/d central mill to process gold ores of the Thames area of New Zealand from small mines in the district. The ores of the region exhibit various degrees of refractory response to conventional cyanidation leach due to the fineness of the gold, and association with pyrite. The alternative circuits involving cyanidation, flotation, and possible small-scale smelting are examined. The environmental impacts have been audited by the Commission for the Environment and were found to be acceptable.

Jan 1, 1986

By J Ward, B Rohrlach, B Rosero, J Silva, O Poma

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Alpala copper-gold deposit is a recent, high-grade porphyry Cu-Au discovery located in the Imbabura Province of north-western Ecuador. The deposit lies along the crustal-scale Chimbo-Toachi Fault Zone within the Dagua-Piñon terrane, which is an oceanic plateau accreted to the South American convergent margin in the Late Cretaceous. The deposit is hosted by quartz diorite stocks that intrude andesitic volcanic breccias of the Oligocene to mid-Miocene San Juan de Lachas Formation. Miocene-age calc-alkaline plutonism is associated with porphyry Cu, Cu-Mo and Cu-Au deposits in southern and northern Ecuador. The Alpala deposit lies along a sector of the Miocene arc that has recently been underplated by the Carnegie Ridge seamount chain that induced shoaling of the subducted Nazca plate beneath northern Ecuador.Surface expressions of the deposit were recognised in May 2012 during follow-up of stream sediment anomalies, when outcropping sheeted and stockwork porphyry-related veins were discovered in Quebrada Alpala. The roots of a NW-trending, structurally-controlled lithocap were recognised over an area of 4.5 × 0.9 km. The remnant lithocap exhibits well-defined mineral zonation mapped by TerraSpecTM analyses on grid soil samples. Soil sampling, heliborne magnetic surveying and channel sampling defined initial drill targets.Seven diamond drill holes were completed in the year from September 2013. Drill hole CSD-13-005 intersected 672 m grading 0.93 per cent Cu and 0.91 g/t Au in high-temperature, inner propylitic and locally potassic-altered quartz diorite intrusions. Overlying hydrothermal clay alteration assemblages define the base of the lithocap. A NW–SE trending footwall structure defines the south-west margin of the deposit. Drill hole 5 intersected high-grade sheeted ‘B-type’ and ‘C-type’ veins (Gustafson and Hunt, 1975) that lie along the south-west margin of an 1100 × 500 m magnetic anomaly that is the focus of ongoing exploration.CITATION:Rohrlach, B, Poma, O, Rosero, B, Silva, J and Ward, J, 2015. High-grade porphyry copper-gold mineralisation in north-west Ecuador – The Alpala Cu-Au porphyry discovery , in Proceedings PACRIM 2015 Congress, pp 369–376 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By G Tsatouhas, R Newell, K Y. Wong

A sulfide ion selective electrode was used to control sulfidiser addition in the flotation testing of a synthetic and a naturally occurring ore containing malachite in order to compare the behaviour of sodium sulfide and calcium polysulfide. Both slug and controlled potential sulfidisation methods of addition were used. Under defined optimum CPS conditions, calcium polysulfide was a more effective sulfidising agent than sodium sulfide on the basis of both capital and operating costs. Surface and solution studies were used to compare the mechanism of each sulfidiser. For calcium polysulfide, XPS showed that polysulfide ions are adsorbed, whereas for sodium sulfide it is the hydrosulfide ions that are adsorbed on the mineral surface. For calcium polysulfide, the CuSx layer was believed to form on the malachite surface, which promoted the flotation of the malachite, by xanthate. Studies of surface morphology of the sulfidised malachite showed that a fairly uniform sulfidised layer is formed with both reagents. The use of sodium sulfide resulted in a thinner initial sulfidised layer compared to polysulfide at equivalent initial sulfur concentration.

Jan 1, 2005

To George Orwell the year of 1984 was the inspiration for a book. To most New Zealanders it was the year that the fourth Labour Government was elected to power. It was also the year that the review of mining legislation commenced. While Orwell's book and the election of Labour are clearly events of some historic note, one could be excused for classifying the review of minerals legislation somewhat differently in terms of its present achievements! Since the review began it has led a tortuous path through a rapidly evolving policy environment to a point three years hence where no major policies have been determined.

Jan 1, 1987

By B Murphy, A Uliana, P STrgio de Oliveira, G Ara·jo de Souza Franco, T Miettinen

Outotec has performed numerous research and development projects and various surveys in the study of reverse iron ore flotation. Over the past four years their TankCell-70 and TankCell-160 flotation cells at the Germano concentrator of Samarco in Brazil were extensively surveyed. These surveys have revealed some extreme operating conditions in reverse iron ore flotation and are the subject of this paper. Some of the findings include large variations in the content of solids in the various flotation stages. At the bottom of the cleaner cells, the content of solids by weight reached over 60 per cent, whereas at the bottom of the scavenger cell this was less than 50 per cent. Froth carry rates were also significantly different in the various flotation stages. In the case of coarse material, the scavenger cells operated at a froth carry rate of over 40 t/h.m2. With fine material, however, froth carry rates of less than 10 t/h.m2 were measured. High froth carry rates caused significant changes in the residence times at Samarco. In the rougher cells, the fifth cell had more than double the residence time of the first cell. This was even more pronounced with the scavenger cells, where the second cell had more than triple the residence time of the first cell. High froth carry rates also caused losses in iron recovery. As a consequence of such findings, it appears that different rules apply in the sizing of reverse flotation circuits compared to direct flotation circuits. Different operating parameters (mixing intensities and air flow rates) must also be used in the rougher, cleaner and scavenger cells in order to optimise the metallurgical performance. Outotec has also been working on a number of new technologies aimed at improving the metallurgical performance of iron ore reverse flotation circuits by increasing froth carry rate and decreasing fine iron entrainment.CITATION:Miettinen, T, Uliana, A, Ara·jo de Souza Franco, G, STrgio de Oliveira, P and Murphy, B, 2013. TankCell flotation at SamarcoÆs Germano concentrators, in Proceedings Iron Ore 2013 , pp 441-444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By P J. White, J V. Lawless

Low-sulphidation epithermal gold deposits, which form in quasi-hydrostatic convective hydrothermal systems, frequently contain chalcedony within high-grade ore, which has been interpreted to be a crystallisation product of amorphous silica. To deposit amorphous silica rather than another silica polymorph at elevated temperatures requires very high silica concentrations, because of its relatively high solubility. Only extreme boiling caused by decompression followed by wall rock heating upon structural dilation, can achieve this. As gold deposits with amorphous silica it must be produced by the same mechanism, particularly since extreme boiling is also a very effective mechanism for gold deposition. Recent developments support this view; the first is the detailed isotopic analysis of chalcedony-bearing high-grade veins reported from Hishikari, Japan, in which oxygen isotope results are indicative of extreme boiling and hydrogen isotopes indicate initial deposition of amorphous silica. The second is the finding of chalcedony within geothermal pipe work in the Rotokawa geothermal field in New Zealand. Rotokawa is a comparatively hot field (335¦C at depth); hence separation of the steam-water mixture produced by the wells is undertaken at a comparatively high temperature (220¦C) to minimise down-stream silica scaling. Even so, silica scale, some of which is chalcedony, does occur, under similar conditions to that in low-sulphidation epithermal deposits. Evidence of chalcedony forming under these conditions, reinforces the interpretation that decompressive boiling is the main deposition mechanism for gold in low-sulphidation epithermal deposits. It is possible that there is sufficient drop in temperature due to decompression that, at least initially, the silica deposits directly as chalcedony. Low-sulphidation epithermal gold deposits that do not contain chalcedony, such as those in the Philippines, may form at temperatures too high for chalcedony to directly form. The recognition of decompressive boiling as the main deposition mechanism in low-sulphidation epithermal deposits means that exploration can focus on zones where this has taken place by combining paleohydrological reconstruction and structural geology.

Jan 1, 2002