Search Documents

Separation of Nickel and Cobalt from Manganese, Magnesium and Calcium by Synergistic Solvent Extraction - From Batch Tests to Pilot Plant Operation The synergistic solvent extraction system consisting of Versatic 10/LIX63/TBP was used for the separation and purification of nickel and cobalt from synthetic laterite leach solution after iron removal. Very encouraging results were obtained for separating nickel and cobalt from manganese, magnesium and calcium. In batch tests, the organic composition of the synergistic system was optimised and very large synergistic shifts for nickel and cobalt were observed. The ?pH50(Mn-Co) and ?pH50(Mn-Ni) values were as large as 1.65 and 2.40, respectively. The extraction and stripping kinetics of nickel and cobalt was fast. Semi continuous extraction tests were conducted with a pH profile of 5.5/6.1/6.5 in three stages at 40¦C. The nickel and cobalt extractions reached 99.9 per cent with only 5 mg/L Ni and <1 mg/L Co left in the raffinate. With two stages of scrubbing, only 2 mg/L Mn and less than 1 mg/L Mg and Ca were left in the scrubbed organic solution. With two stripping stages, the stripping efficiencies of Ni and Co reached over 95 per cent. A fully continuous pilot plant operation was conducted successfully for 280 hours. With an O/A ratio of about 2 and a pH profile of 5.5/5.8/6.0/6.3 for the four stages EX1/EX2/Ex3/EX4, both nickel and cobalt were almost completely extracted. Using a pH profile of 5.4/5.0 for SC1/SC2, the manganese scrubbing efficiency was over 96 per cent. Using three strip stages, over 98 per cent Ni and 99 per cent Co were stripped with only 64 mg/L Ni in the stripped organic solution. The nickel concentration in the loaded strip liquor reached 83 g/L, resulting in a ?Ni of over 28 g/L. The chemical stability of the system was also assessed over 12 weeks under proposed industrial operating conditions. Operation exclusively under strip conditions at 50¦C and 40¦C resulted in LIX63 oxime half lives of 1.1 and 2.1 years, respectively. Operation exclusively under extract conditions at 50¦C and 40¦C resulted in oxime half lives of 0.26 and 0.82 years, respectively. Losses of Versatic 10 were less than four per cent.

Sep 13, 2010

By C M. Hall

We report 40Ar/39Ar ages for adularia and illite from veins and wall rocks at the Waihi and Favona deposits, in the Waihi district. One sample of vein adularia from the Favona deposit yielded a plateau age of 6.04 ¦ 0.06 (la) Ma, and two samples of vein adularia from the Waihi deposit yielded plateau ages of 6.17 ¦ 0.03 and 6.17 ¦ 0.09 Ma. Two samples of wall rock adularia from the Waihi deposit yielded plateau ages of 6.07 ¦ 0.06 and 6.08 ¦ 0.03 Ma. Adularia ages overlap at the 2s level, and we do not consider them to be significantly different. Two samples of illite from wall rocks at Favona have total gas ages of 5.66 ¦ 0.04 and 5.65 ¦ 0.04 Ma, and retention ages of 6.57 ¦ 0.04 and 6.61 ¦ 0.04 Ma, whereas one sample of vein illite yielded a total gas age of 5.29 ¦ 0.17 Ma, and a retention age of 6.26 ¦ 0.19 Ma. The total gas ages of illite are minimum ages that are equivalent to conventional K/Ar analyses, whereas retention ages of illite are maximum ages. Although interpretation of the illite data is complicated, the adularia results strongly suggest that the Waihi and Favona deposits formed contemporaneously in the same fossil geothermal system at 6.0 to 6.1 Ma.

Jan 1, 2003

Ore samples generally require preparation before analysis. Serious problems can occur with contamination degradation and particle size effects. Both grinding element contammation and sample cross contamination havebeen bound to be related to sample hardness and operator technique. For best results with minerals relevant to the steel industry, the use of Siebtechnik-type mills required a combination of careful planning, short grinding periods and intermediate sieving of the sample. The results may be extended to most mineral, rock, and refractory sample preparabons.

Jan 1, 1978

The nature of the specialty glass and ceramic business magnifies the dependency of the ultimate product on the unique properties of their raw materials used to make them. This dependency has implications in the management of risk in the supply process which requires a special procurement organization and program commitment to be successful. The Coming system of managing critical materials and factors in development of alternate new suppliers and products is discussed.

Jan 1, 1989

By Carras S, Kelsey P, Caccetta L

An important problem in open pit mine planning is that of detennining the optimum ultimate pit limits of the mine. These limits are that contour which is the result of extracting the volume of material which provides the total maximum profit while satisfying certain practical operational requirements such as safe wall slopes. The determination of the optimum pit contour provides information that is essential in the evaluation of the economic potential of the mineral deposit. A number of optimisation techniques are available for determining this contour with the Lerchs-Grossman and the Network Flow methods being the most favoured. Unfortunately, direct application of these techniques to large ore-bodies may cause considerable difficulties because of the computational time and storage requirements. In this paper, we present a strategy for resolving these problems, and the associated pit design software PITOPTIM (incorporating a fast network flow technique) and a data reducer, BOUND. The results presented highlight the speed and power of the software package rivalling the popular Lerchs-Grossman technique. An application of the software for a sensitivity analysis is also presented and discussed.

Jan 1, 1991

The Fosterville Goldfield has a modest past production (0.3 Moz), but is now emerging as a significant goldfield (2.6 Moz resources, including 1.1 Moz reserves) with implications for exploration within the orogenic gold provinces of the Lachlan Fold Belt in Australia and the Buller Terrane on the West Coast of New Zealand. Fosterville is located 20 km east of the 22 Moz Bendigo Goldfield and is geologically similar to other Victorian goldfields, however the nature of the gold mineralisation differs significantly. Unlike other Victorian goldfields there is no primary free gold at Fosterville. The gold occurs in as sub-SEM resolution particles, in fine grained arsenopyrite and pyrite crystals disseminated through the wall rocks in fault controlled quartz-carbonate vein stockworks. The Fosterville Goldfield comprises several subparallel fault systems striking 340¦ over an exposed strike length of 28 km. The Fosterville Fault system comprises the west dipping (~75¦), reverse Fosterville Fault and several less steeply west dipping splay faults formed in the footwall. The splay faults extend through east dipping beds from the Fosterville Fault across a syncline hinge into stratigraphically controlled positions on the west dipping limb of the syncline. The predominant control on gold mineralisation is the intersection of the bedding on the east dipping limb of the syncline and faulting which, is in turn controlled by the orientation of bedding in the west dipping limb of the syncline. The mineralised shoots are thus subparallel to the plunge of the syncline and show a plunge reversal about a culmination in the footwall syncline. This provides a very powerful exploration tool with bedding û cleavage intersection lineations measured in outcrop and oriented core indicating the plunge of mineralisation. Mineralisation is also, albeit less commonly, controlled by local variations in strike and dip of the host fault and at metre scale by host lithology. As the faults and mineralisation are stratigraphically controlled, detailed stratigraphic interpretations are essential to provide control on structural interpretations for resource modelling. Compared to other Victorian goldfields, the Fosterville Goldfield formed later (385 Ma to 360 Ma cf 440 Ma), at lower temperatures and at shallower depths (fluid inclusion studies of Au associated veins suggest vein formation at ~270¦C (range 140¦C to 385¦C) and at depths of 2.6 - 5.7 km).

Jan 1, 2005

TIMBER supports for large underground cavities are temporary expedients until the permanent filling can be put in. Nevertheless, timber supports are very necessary in some form. The general problem is to support the cavity in all directions withthe minimum of timber, disposed in the strongest way. The simplest way of filling an irregular space with timber sets is to form triangles.The right-angled isosceles triangle (Fig. 1) leads to the true square set, in which caps are equal to struts. The right-angled unequal-sided triangle and the scalene isosceles triangle (Fig. 2) lead to the oblong square set, where caps are longer than struts.The scalene triangle (Fig. 4) leads to the rhombic or oblique set. The equilateral triangle leads to the hexagon set (Fig. 3), in which the caps and struts are all equal. These five plane figures, the triangle, square, rectangle, rhomb and hexagon, are the only figures that will completely fill any irregular plane figure, without interstices. Hexagon sets were first suggested by the writer in 1902 to a mine manager at Broken Hill, who did not see his way to use them.

Jan 1, 1912

By D J. Brake

There has been a strong trend over the past decade in hard rock mines towards the use of very high powered auxiliary (or secondary) fans; in many mines, the installed power for the secondary ventilation system now exceeds that of the primary ventilation system. This also reflects the trend to use two-stage auxiliary fans pushing air into a single ‘trunk’ duct that in turn splits into multiple branches with multiple outlets feeding multiple workplaces. This often produces a poor result in terms of face flows due to the high resistance, high leakage and badly managed duct outlets, as well as high fan capital and operating (power) costs, which in turn also results in a higher cost for the underground power reticulation/distribution systems. This paper explores the reasons why this trend exists and what ventilation practitioners can do to utilise less expensive systems that simultaneously deliver better workplace conditions. It includes a case study.CITATION:Brake, D J, 2017. Auxiliary ventilation design – why and how mines waste so much power on inferior systems, in Proceedings Australian Mine Vent Conference 2017, pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By A Sainoki, D Fukuda, K Shioya, C Zhang, M Sharifzadeh, T Yamaguchi, S Saydam, J Kodama, C A. Amagu, Y Fuji

In an open pit mining, ensuring stability of rock slope has been one of the major challenges. As the instability of rock slopes can results in slope failures; consequently, endanger the lives of workers, affect mining operations, and often lead to economic losses. Therefore, it is practical important to study the stability of rock slopes to ensure safe, smooth, and effective mining. The stability of rock slope of about 130 m height at Higashi-shikagoe limestone quarry, which has experienced slope failures four times since 1996, was assessed. The rock mass at the quarry is consists of mainly limestone, schalstein and slate rocks intersected by clay seams of about 70 m thick at footwall of the rock slope. Previously, the effects of limestone excavation at the foot of the rock slope and shear failure due to rainfall infiltration have been investigated. Although clay is widely known to plays a vital role in the stability of slopes in engineering projects including mines, but its impacts on slope deformation at the study quarry are not adequately examined. Therefore, the present study addressed the impact of presence of clay on slope deformation at Higashi-shikagoe limestone quarry by employing both field displacement measurements and numerical simulation. Firstly, surface displacements measured by automated polar system (APS) for over eight years were analysed to understand the overall characteristics of the slope deformation. The measured results show that the displacement gradually decreases with time. The maximum displacement of about 100 mm was observed at middle of the rock slope. Secondly, the effect of deterioration and plastic behaviour of the thick clay layer were simulated using two-dimensional finite element method (2D FEM). The simulated results reveal that the clay exhibited deterioration by water contact and plastic behaviour arising from mining activities at the footwall of the clay zone. Based on the characteristics of the measured and simulated results, it was found that the displacement induced by the effect of deterioration of clay is more noticeable at the north side of the quarry whereas displacement induced by excavation is quite significant at the south side of the quarry if clay behaves as an elasto-plastic material.

Nov 29, 2022

Andesites are a major source of aggregate for much of the North Island of New Zealand. There are regional differences with respect to some important properties of the andesites. Some are reactive with cement and are designated as potentially deleterious or deleterious by the concrete industry. Other andesites, particularly those that are slightly altered or weathered, have rather high Plasticity or Clay Indices and perform poorly in road construction.   The performance of the andesites has been investigated and can be shown to be determined by: +        the chemistry of the rock which in turn determines the chemistry of the glass in the rock; +        the presence of large amounts of groundmass glass in the rock; and +        the nature of the superimposed alteration processes. Environment of extrusion and how rapidly the rock has been cooled or chilled are also important as they determine the fabric of the rock and how much glass will be present in the rock.   There are three main types of alteration that affect the quality of the aggregate: 1.   hydrothermal alteration, 2.   late magmatic alteration associated with the devitrification of glass, and 3.   weathering.   Each of these alteration types produces different alteration minerals. In fresh andesites the devitrification of glass has an important affect on the rockÆs properties. The Taranaki andesites are shown to have unusually (in comparison with other North Island andesites) high Na2O contents, held in the groundmass glass, which is the fundamental reason for the high alkali û silica reactivity of these andesites.

Jan 1, 2005

Over years of exploration the massive and tabular orebodies in the area to the South West of Western Areas Gold Mine had been assessed as containing about 50 million ounces of gold û a world class orebody. Planning initially was for a surface and subvertical shaft system to exploit this area but because of cost, a single lift shaft to an area which could be accessed ex Western Areas was planned to intersect the reef at 2760 metres. It was also planned to mine out the shaft pillar area long before the deep shafts would reach that position. This is not the normal practice in South African Gold Mines. The stoped out shaft pillar was backfilled to minimise movement in the shaft sites. The result of a competitive tender/adjudication process was that Cementation Mining û Skanska won and was awarded the R192 million contract to sink the Main and Ventilation Shafts on 15 June 1995. On 1 April 1999 Western Areas and Placer Dome SA formed a Joint Venture, which now owns and operates the mine on which the South Deep Shafts are situated. This situation prevails today.

Jan 1, 2002

By N Dube, K L. Sandvik, C Mutevhe

Trojan Nickel Mine is the largest producer of Ni, Cu and Co in Zimbabwe. The mine has operated a nickel flotation concentrator and base metal refinery continuously since 1969, creating 28 million tonnes of sulfide bearing tailings, five million tonnes of permanent waste rock and about seven million tonnes of smelter slag. Exposure of the sulfide bearing minerals renders them susceptible to oxidation in the presence of water and oxygen, resulting in acidic solutions with elevated concentrations of total dissolved solids, sulfate, metals and residual flotation chemicals in various waters draining from the mine site. These pollutants pose a direct threat to the environment and human health, and understanding their deportment and behaviour in the various waste streams is essential in the mineÆs environmental objectives to prevent or minimise adverse impacts arising from its operations. A geochemical assessment of the pollutants was carried out to compute a mass balance between the major sources of pollution and the distribution and fate of pollutants in waste streams from the mine site. Waste rock, tailings, surface water, ground water and sediments were sampled, tested and analysed. Mineral composition and water chemistry data show that geochemical reactions are responsible for the release of pollutants from waste rock, tailings and plant spills. Drainage from the mine area is near neutral due to buffering by magnesium carbonates in the fine fraction of the tailings. The natural wetlands that exist downstream of the waste rock and tailings dams are effective in reducing metal loadings to water courses. However, solutes and heavy metals are occasionally released to surface and ground water, when their concentrations peak during the dry season. The results demonstrate the necessity to understand the natural chemical processes that characterise the distribution of pollutants in nature and how such knowledge can be used to develop cost effective methods to remediate pollution in the natural environment.

Jan 1, 2006

By A P. Brown

Comparison of legal permits required for mining (as opposed to prospecting or exploration) inNew Zealand, under the Mining Act 1971 and the Resource Management Act/Crown Minerals Act 1991. Mining generally receives the same treatment as any other industrial or commercial activity.

Jan 1, 1995

The role of government and the community has changed significantly over the last two decades in relation to environment protection, particularly in the mining sector. Increased community expectations have moved well ahead of regulatory requirements, and there is now a much greater appreciation generally of the concepts of ecologically sustainable development and intergenerational equity, and the gap between current practice and practices which would be in harmony with these concepts. Besides providing a `safety net' through regulations to ensure that basic environmental performance standards are met, government is now working proactively with the mining industry to encourage higher levels of environmental performance. This paper describes some initiatives between the Commonwealth government and the industry designed to achieve these higher levels of environmental performance, through programs aimed at the paradigms of best practice environmental management and continual improvement.

Jan 1, 1997

By L R. Marshall, M J. Rubenach, T G. Blenkinsop, J S. Cleverley

The source and transport regions of fluidised (transported) breccias outcrop in the Cloncurry Fe-oxide-Cu-Au district, providing insights into the origins of other fluidised magmatic-hydrothermal breccias such as kimberlites. Discordant dikes and pipes with rounded clasts of metasedimentary calc-silicate rocks and minor felsic and mafic intrusions extend several kilometres upwards and outwards from the contact aureole of the 1530 Ma Williams Batholith into overlying schists and amphibolites. The brecciation initiated at depths >10 km and may have resulted in surface breaching. We used analytical equations for particle transport to estimate clast velocities (eÆ 20 ms-1), approaching volcanic ejecta rates (up to 80 ms-1). The wide range of CO2 fluid inclusion densities (up to 150 MPa), the localisation of the base of the breccias in contact aureoles, and the scale and discordancy of the bodies suggests the breccia transport process was triggered by an abrupt release of overpressured fluid. At these depths, such extreme behaviour may have been achieved by release of dissolved fluids from crystallising magma, in combination with a strongly fractured and fluid-laden source, sitting under a strong, low permeability barrier, and such parameters may be analogous to the asthenosphere/lithosphere boundary in the case of kimberlite initiation. The relationship of these breccias to the Ernest Henry iron-oxide-Cu-Au deposit suggests they may have been either fertile or æfailedÆ orebody feeders.

Jan 1, 2005

The metallogenic map of New Zealand shows the distribution of metallic mineral deposits, according to type and size, in relation to their geological setting. The major purpose of the map and accompanying 200-page monograph is to summarise the distribution, modes of occurrence and origins of the metallic mineral deposits of New Zealand. The map demonstrates the prospectivity of New Zealand for metallic minerals, particularly gold, silver, iron, and titanium. Information on each deposit is summarised in index tables based on major geotectonic units or deposit/commodity type. The mineral deposits are arranged and discussed in relation to tectonostratigraphic and tectonomagmatic units or terranes, under broad geotectonic divisions of the Paleozoic to Mesozoic Western Province, the late Paleozoic to Mesozoic Eastern Province, the mid Cretaceous to early Tertiary rifting phase, and the late Cenozoic Kaikoura Orogen. Regions or areas of marked concentration of mineralisation are recognised as metallogenic subprovinces or districts, namely: eastern Northland (Hg), the Hauraki Goldfield (epithermal Au-Ag-Pb-Zn-Cu), the west coast of the North Island (shoreline placer Fe), east Nelson (podiform Cr), west Nelson (porphyry Mo), the West Coast of the South Island (shoreline placer Ti), west Nelson-Westland (placer Au), Reefton (mesothermal Au-quartz veins), and Otago (placer Au and mesothermal Au-W quartz veins).

Jan 1, 1993

The ore milled from the Lead Lode of The Zinc Corporation leases consists of a fairly granular mixture of galena, marmatite, chalcopyrite, tetrahedrite, pyrrhotite, pyrite, and lollingite with a gangue association of calcite, quartz, bustamite, rhodonite, mangan-hedenbergite, garnet, fluorite, mangal1o-calcite and apatite. The silver content of the ore occurs in three minerals-tetrahedrite, dyscrasite, and pyrargyrite, the last two mentioned occurring in microscopic association only. Other metallic and gangue minerals are also present in this complex mineralogical association, but do not influence the milling operations. Fortunately, the silver minerals favour the galena and chalcopyrite as their host minerals, thus facilitating the recovery of both copper and silver in the lead concentrate. The ore from the Lead Lode assays from 14-18% lead; 3·0-4·5 oz. silver per ton, and 9·5-12·0% zinc.A parallel lode, known as the Zinc Lode, is well developed in The Zinc Corporation leases. This lode assays from 6-8% lead, 1·5 oz. silver per ton, 18-25% zinc with a siliceous gangue. The common Lead Lode gangue minerals-ealcite, rhodonite, bustamite-are very rare in present underground exposures. No metallurgical work was done on this ore during the pilot plant operations.The aim in the milling process is to produce: 1. A lead concentrate with the maximum economic recovery of lead, silver, gold, copper and antimony, and minimum zinc content.2. A zinc conc,entrate with the maximum economic recovery of zinc, cadmium, and cobalt, and minimum iron, arsenic and fluorine content.3. A waste residue containing sufficient granular material to be utilized as underground fill.In considering the economics of the milling practice the above three requirements plus consideration of the tariffs submitted by the purchasers of concentrates were the deciding factors in the evolution of the present milling practice.Towards the end of 1924 The Zinc Corporation Limited added to and adapted the old zinc tailings plant for the treatment of 5,000 tons of crude ore per week. This plant, which operated until January, 1936, was in general principles similar to the standard Broken Hill methods of ore concentration, whereby the galena was recovered by the gravity concentration methods of Hgging and tabling with selective flotation concentration of the residual galena and marmatite. One important difference from other Broken Hill plants was that the primary grinding of the jig tailing was performed with flint-loaded mills operating in closed circuit with revolving screens. Two primary grinding sections were installed, each...

Jan 1, 1941

By V M. Silva, P A. A Martins, V O. Matthew, A L. S Fonseca, E B. Cunha, A J. D Ferrari, E M. S Silva, A C. Silva, D R. T Vilela

The Anglo American phosphate mine is located in the Brazilian state of Goiás and possesses one of Brazil’s most important phosphate rock deposits, with the site being the country’s second largest producer of phosphate rock concentrate. Despite the site having been in operation since 1979, the mining team only started using explosives in 2004 when rocks with greater hardness started to appear in the mine’s geological profile. Rock excavation was previously performed mechanically. Until 2013, only rocks with high hardness were blasted, this following the standard drilling grid that was defined in 2004 without any changes in the blast parameters. The aim of this paper is to show how fragmentation optimisation has yielded positive results at all stages of the production chain, from the mine to the mill passing through an impact hammer crusher, a rod mill and ball mill, operating in close circuit with hydrocyclones.While incorporating the mine to mill holistic approach during the operational integration, the focus was on defining the blasting domains and respective optimal fragmentation and measuring the benefits of blasting in terms of reduction in energy and grinding media consumed in the comminution processes. In the first stage, the blasting team made changes to the blasting parameters and assessed the effects of these changes on fragmentation using computer software and on-site measurements. This generated a database that made it possible to divide the mine into blasting domains. For the second stage, teams from the plant, geology, mine planning and operation departments jointly made comparisons between the performance when processing stockpiles, which only included high hardness blasted ore (20–30 per cent of blasted ore). Changing the drilling grid’s size from 3.0 m × 3.8 m to 2.0 m × 2.6 m for high hardness rock with the presence of silicates resulted in a 40 per cent reduction in the P80 for the blasted material (from 459 to 278 mm), while changing the grid from 3.0 m × 3.8 m to 2.6 m × 3.2 m for high hardness rock without the presence of silicates generated a reduction of 25 per cent (from 270 to 204 mm). There were gains observed from the measurements at the mineral processing plant in terms of specific energy spent on comminution and on the consumption of grinding bodies in the rod mill. There was a measured reduction of circulating load during secondary grinding and a reduction in slime generation.CITATION:Silva, A C, Martins, P A A, Silva, E M S, Fonseca, A L S, Ferrari, A J D, Cunha, E B, Silva, V M, Matthew, V O and Vilela, D R T, 2015. Fragmentation optimisation – adopting mine to mill for reducing costs and increasing productivity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Pfeifer H. C, Nicacio P. A D

Sinter has been used as part of the metallic charge in large-scale blast furnaces for many years with the well-known benefits in terms of productivity and fuel consumption. However, because of the high investment in a conventional sinter plant, small blast furnaces and the associated integrated mini steel plants have not taken the advantages of using sinter. Recently KTS Korf Tecnologia Siderurgica, a division of Mannesmann Demag Ltda in Brazil, has developed a mini sinter plant for which the investment is compatible with small blast furnaces. Consequently, it is of great interest to evaluate the economical impact of using sinter in such small-scale integrated steel plants. In order to compare two alternatives, ie 100 per cent ore and 70 per cent sinter in the blast furnace burden, mass and heat balances for the entire operation from sinter plant through the blast furnace and EOF-based melting shop, were performed to evaluate the final production cost of the liquid steel. It was found that, depending on the sinter feed price, substantial savings can be obtained with the use of sinter.

Jan 1, 1999

New Zealand China Clays produces a unique halloysite clay product at Matauri Bay, Northland.   The company has licences over four deposits that were derived from the weathering of rhyodacite domes. Clay is mined and processed from two of the four deposits and is refined using a complex process based on gravity separation.   The product is almost entirely exported to niche markets in 24 countries. The main market is the fine ceramic industry where the product is used as a component in the manufacture of high quality porcelain and bone china bodies. The use of halloysite in these bodies gives the manufacturer the ability to achieve high whiteness and translucency. The other major market is for use in technical ceramics, where the product is sought after due to its high purity, fine particle size and stability at high temperatures.

Jan 1, 1997