Search Documents

By Spooner H. W

The paper describes the search for mineral deposits in an area of 4,500 sq. miles of south-west Tasmania. The area is one of difficult access and the problem of speedy movement and maintenance of field parties was solved by the use of helicopters. The programme has followed a systematic pattern of the aerial photography of the exploration area with the preparation of photQmosaics and topographical base sheets from these mosaics. Geological maps were initially prepared by photogeological interpretation and making use where possible of pre-existing information. The maps produced were later checked by ground traverses. Geophysical maps were obtained by the use of airborne magnetic, electromagnetic and radiometric methods. Geophysical and geological anomalies were checked on the ground by a campaign using ground geophysical equipment in the former case and geological and geochemical work in both instances. Audio Frequency Magnetic and Induced Polarization techniques were used in an area which was covered by several hundred feet of Tertiary sediments.The campaign has reached the stage of the drilling of specific targets.INTRODUCTIONThis paper describes the activities of Lyell-E.Z. Explorations (L.E.E.), an organization which was formed in 1956 by the Mt. Lyell Mining and Railway Co. Ltd. and the Electrolytic Zinc Co. of Australasia Ltd. to explore for mineral deposits in an area of approximately 4,500 sq. miles in southwest and southern Tasmania. To provide the necessary personnel and equipment for this project the exploration resources of both Companies were pooled and augmented and a headquarters was established in Queenstown. The work was directed by a Committee of four made up of officials from both Companies; a review of this structure has recently been presented by Hall (1959).

Jan 1, 1960

By K H. Esbensen, K Engström

The conclusion from the debate over the last decade in the mining sector is that, for grade control, reverse circulation (RC) drill sampling gives more reliable results due to less sampling problems than blasthole samples. However, by conducting the latter with well-controlled procedures there still exist fair possibilities to counteract the major blasthole sampling problems and achieve fit-for-purpose representativeness, especially if based on minimal loss of fines. In the present PhD study, extensive replicate experiments and variographic characterisations are conducted to evaluate the performance of manual blasthole (BH) sampling and sectorial segment sampling. The experiments were performed in Luossavaara-Kiirunavaara AB (LKAB)’s Leveäniemi open pit mine in the north of Sweden. The experimental area is an apatite-magnetite iron ore deposit of the Kiruna type, with the demand to exhibit a maximum of local heterogeneity to allow the experiment the largest possible conclusion powers. Gathering and splitting the complete BH drill cutting cones (fines cone, coarse cone) served as an authoritative reference on which to assess the representativity of the two BH sampling methods.Results show that manual BH drill sampling is able to produce samples with an acceptable accuracy and precision if performed properly and with insight. Based on variographic comparison, segment sampling shows similar precision for chemical grades as the manual sampling, while the particle size distributions were more deviating for segment sampling than for manual sampling at the high and low size ranges. Possible reasons for these partly surprising results are discussed.For further investigation of the performance of BH versus RC drill sampling, a second experiment has been planned on a parallel profile. This will result in an unprecedented opportunity for a full variographic comparison between RC and BH sampling, aimed at designing specific, fit-for-purpose sampling procedures as a function of ore quality, cut-off grades and important contaminant levels.CITATION:Engström, K and Esbensen, K H, 2017. Blasthole sampling (replicate and variographic experiments) in LKAB open pit iron ore mines – fit-for-purpose representativity?, Australia, in Proceedings Eighth World Conference on Sampling and Blending , pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

This paper contains an account of some creep tests on electrolytic lead and some of its alloys. The stresses used in determining creep were 500, 350, and 200 lb. per sq.' in. The alloys contained silver, bismuth, tellurium, antimony and zinc respectively. All were castin vacuo, and tested "as rolled." Tests were done also on electrolytic lead which had been cast in air.The electrolytic lead contained 0.0005% total impurities.The preparation and vacuum casting of this lead have been described in a previous paper in this series. The preparation of the alloys, and the air casting of the electrolytic lead, are described in the next section.EXPERIMENTAL PROCEDURE.Every effort was made to keep the vacuum-cast specimens from contact with the atmosphere throughout their history.The ingots were stored eIther in a vacuum desiccator or immersed in heavy oil. The creep specimens were coated with vaseline except during rolling, etching and photography, which involved exposure to the atmosphere for about 45 minutes all told.It is not claimed that vaseline is a perfect shield against the intrusion of atmospheric gases. Possibly during the months that some tests were in progress the gases diffused through the vaseline and gained a limited access to the lead.Nevertheless, the use of vaseline gave protection that brought the tests nearer the ideal at which the author aimed, *Research Fellow, Dept. of Metallurgy, University of Melbourne.

Jan 1, 1936

By Satayev IS, Shepelev DV

Various ways for applying the X-ray fluorescent method to process lump-by lump separation of secondary aluminium raw materials (scrap, slags, waste) as well as ferrosilicon and ferrochromium are being considered and physically demonstrated. A commercial X-ray radiometric sorter has been developed for processing secondary raw materials. Marketable quantities of aluminium scrap with appropriate copper and zinc content have been produced for smelting with a minimal additional of pure aluminium. An industrial complex for scrap processing, incorporating two X-ray radiometric sorters from the Hammermils company is successfully operating at one of the works in Russia.

Jan 1, 1993

A modified liquation technique was developed for recovering tin from tinhouse scruff metal or hardhead containing about 10 per cent iron and 15 per cent occluded flux, palm oil, and moisture. This was effectedby heating the scruff metal to 950°C followed by rapid cooling to suppress the formation of FeSn2 and FeSn, and then subjecting it to the ordinary liquation and drossing processes of refining. By this method it was possible to recover about 83 per cent of the original tin content and, with subsequent smelting of the irony drosses, an overall recovery of 92 per cent was obtained.

Jan 1, 1969

This paper gives an overview of the difficulties associated with determining the strength of hard rock pillars. Although a number of pillar design tools are available, pillar collapses still occur. Recent examples of large scale pillar collapses in South Africa were caused by weak partings which traversed the pillars. Currently two different methods to determine the strength of pillars are used namely, empirical equations derived from the back analyses of failed and stable cases and numerical modelling tools with an appropriate failure criteria. Both techniques have their limitations and additional work is required to obtain a better understanding of pillar strength. Empirical methods are popular and easy to use, but care should be exercise that the results are not extrapolated beyond the range of the data which were used to derive them. An example is the Hedley and Grant formula (derived for the Canadian uranium mines) that has been used for many years in the South African platinum and chrome mines (albeit with some adaptation of the K-value) to design the pillar layouts. Very few collapses have nevertheless been reported and it might even be too conservative an assumption of pillar strength in these mines. As an alternative, some engineers strongly advocate the use of numerical techniques to determine pillar strength. A close examination unfortunately reveals that these techniques also rely on many flawed assumptions. An area where numerical modelling is invaluable, however, is to study specific pillar failure mechanisms, such as the influence of weak partings on pillar strength. In conclusion, it appears that neither empirical techniques nor numerical modelling currently provide a solid basis to conduct pillar design. It is therefore recommended that both these techniques be utilised when confronted with a pillar design to obtain the best possible insight into the problem.

Nov 25, 2010

By J Widjaja, E Hermawan, M Muharam, L Damanik

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The island of Java lies within the Sunda-Banda magmatic arc, which is characterised by multiple phases of volcanic activity and extensive compressional deformation. Along this zone, significant gold and copper mineralisation occurs, including some of the world’s largest deposits. In West Java, epithermal gold mineralisation is typically located in a series of extensional and strike-slip faults that cut Miocene to Pliocene volcanic rocks. These are all low-sulfidation, epithermal, vein-stockwork-style deposits developed in Miocene to Pliocene calc-alkaline volcanic rocks, which have been intruded by shallow-level plutons.This paper discusses an example of epithermal mineralisation at Mt Subang, West Java. Gold mineralisation was originally identified from stream sediment, panned concentrate and rock geochemistry sampling in the early 1990s. Geophysical surveys (magnetics and induced polarisation resistivity/chargeability), trenching, pitting and diamond hole drilling has subsequently revealed silicified-quartz vein epithermal gold mineralisation hosted within fault structures. It is clear that these structures acted as hydrothermal fluid pathways leading to the development of mineralised offshoots along north–south extensional and en-echelon arrays of north-east–south-west and transtensional faults. A number of vertical offshoots also occur in flexures and fault jogs. Post-mineral faulting has subsequently dissected and offset a number of the offshoots. Therefore, a detailed knowledge of structure and fault kinematics and displacement magnitudes is required in order to understand the geometry and continuity of mineralisation across major structures and maximise the resource potential. A range of exploration targets were modelled, indicating a minimum and maximum of 0.2 and 1.8 Moz of gold respectively.CITATION:Cunningham, M J M, Muharam, M, Damanik, L, Hermawan, E and Widjaja, J, 2015. Structural controls on the localisation of low-sulfidation epithermal mineralisation in West Java, Indonesia , in Proceedings PACRIM 2015 Congress, pp 227–234 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By P González, E Córdova, E Faundez

An integrated mine system must be capable of displaying and reporting valuable information that can be used to easily understand, manage and take action on the key parameters being reported.One of the key aspects of integration is the standardisation of the mine information up to a level capable of adapting the main characteristics of past projects at the mine and enforcing the same or higher standards for newer projects being developed.At the El Teniente mine, photogrammetry is used to map the advance of horizontal developments, and the constructed 3D representation of each face is then used by the geologists to obtain structural information about the areas being photographed.The mine realised that valuable mining information could also be extracted from the photogrammetry being applied, with three possible areas of development envisioned.The first area was creating a link between the developments being planned on a yearly and monthly basis and matching them with plan sections of the 3D developments of the system to account for any deviations.The second area was to use vertical sections of the 3D developments to estimate the overbreak of the excavations in different areas of the mine.The third area was the provision of a more detailed analysis of the sections so that they could provide information on the thickness of the shotcrete being applied.This paper presents the different alternatives being used and examines how the project is currently being developed and managed at the mine. It also looks at the challenges associated with implementing the reporting platform and the results being obtained.CITATION:Córdova, E, Benado, D, González, P and Faundez, E, 2016. Mine planning information from photogrammetry sources at the El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 653–658 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By P Craig, A Crosky, H Ramandi, S Saydam, H Chen

Frequency of reports on premature failure of rock bolts and cable bolts have increased in past two decades. Such a failure threatens both the safety of underground mine workers and the economic viability of the operations. Herein, we report on analysis of rock bolts and cable bolts failed recently in three underground mines in Australia. Magnetic particle inspection (MPI) and scanning electron microscope (SEM) techniques were used to study the failed bolts. MPI showed a number of subcritical cracks on the surface of the bolts. The majority of the cracks in both cable bolts and rock bolts were initiated from the base of ribs (indentation) where the stress concentration was high. SEM examinations showed tearing topography surface (TTS) in all failed rock bolts and cable bolts. These indicated that the failure occurred through hydrogen assisted stress corrosion cracking (HISCC). The results of this study enhanced the understanding about the failure of rock bolts and cable bolts in underground mines. CITATION:Chen, H, Ramandi, H, Craig, P, Crosky, A and Saydam, S, 2018. Analysis of premature failure of rock bolts and cable bolts failed in underground coal mines, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 407–413 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By D A. Edmunds

The most important development that has been taking place recently relating to mining operations in New Zealand would generally be regarded as being the Resource Management Law Reform. This has been widely publicised by the Government as a comprehensive review of the laws governing New Zealand's natural and physical resources. Submissions have been sought and a free phone provided to encourage public participation. Recently a Discussion Paper has been prepared by the Core Group coordinating the review to explain progress on Phase One (Ministry for the Environment, Directions for Change: A Discussion Paper, Wellington 1988). It outlines Government decisions already taken which impinge on the Review and describes the possible models for resource management laws. However, it is possible that some fundamental practical issues of significance to the mining industry will not be addressed and may be lost sight of in the much wider issues which are to be covered. The purpose of our paper is to address one of these issues namely, the interrelationship between any new resource management legislation and the Conservation Act 1987 (as recently amended) in the context of Ministerial consents. The importance of this issue can be seen from the fact that as at 7 June 1988 there were 279 mining licence applications and 223 prospecting licence applications waiting to be determined by the Minister of Conservation. Since April 1987 only 19 mining and 13 prospecting licences have been consented to. In addition a major proportion of New Zealand's mineral resources are contained with land administered by the Department.

Jan 1, 1988

By M Lentz

This paper will discuss the issues associated with blasting in an urban mining environment that have been addressed by Winstone Aggregates at the Mt Wellington Quarry. These issues include - control of vibration and air overpressure, repeatability of shot performance, fragmentation on an extremely low maximum instantaneous charge, compliance with Territorial Authority regulations and perception. Over the last two years, in order to address these issues, Winstone Aggregates have undertaken a programme of continuous improvement, which has included; ò implementation of new technology; ò revising site procedures; ò conducting an investigation into the structural response of local buildings; ò investigating safe extrapolation; ò extensive public consultation; ò establishing credibility during the consent process; ò identification of perception issues; and ò building relationships and trust with neighbours. The issues addressed at the Mt Wellington Quarry have increasing significance for traditionally rural mining operations, as the input of the local community being urban or rural, increases. New and existing operations have the potential to adopt best practice now, building trust with the community and raising the profile of the industry.  

Jan 1, 1999

By C E. J de Ronde, J G. Scott

Economic gold mineralisation was discovered at Round Hill by Homestake NZ Limited in 1984 and was subsequently put into production by Macraes Mining Company Limited (MMCL) in 1990. The total mineral resource in 1990 was estimated at 41.4 Mt @ 1.42 glt at a 0.7g/t cut off, for 1.8 Moz of gold. Since project start up the mill has been upgraded twice to increase throughput and reached its current capacity of 3.2 Mtpa. At 31 December 1996, a total of 16.2 Mt of ore at average grade of 1.73 g/t has been excavated, yielding 655,000 oz of gold. MMCL began exploration along the Hyde Macraes Shear Zone in 1994. Since 1994, exploration has been successful with the discovery of over 3.5 Moz of gold. The resource now stands at 110 Mt @ 1.46 g/t gold for 5.1 Moz. This success has led to a planned expansion of the processing capacity to 9 Mtpa with the building of a new 6 Mtpa processing plant.

Jan 1, 1997

By R L. Brathwaite

Previous paleodepth studies of low-sulphidation epithermal Au-Ag deposits in the Coromandel region indicated that economic gold mineralisation was generally limited to a depth zone of 100 to 400 m below the paleosurface. Notable exceptions are Waihi and Karangahake, where ore shoots extended to depths of about 750 and 900 m respectively. These studies have been extended to include Au-Ag, Hg and Sb epithermal deposits in Northland and the Taupo Volcanic Zone. The main paleodepth indicators used are sinters and hydrothermal eruption breccias, hydrostatic pressures estimated from homogenisation temperature measurements on fluid inclusions, and hydrothermal alteration mineralogy. Also the occurrence of lacustrine and fluvial sediments is an indicator of the paleosurface at their time of deposition. Selected paleodepth indicators have been compiled and mapped in a GIS environment. The distribution of the paleodepth indicators are used to define regional variations in erosion levels, and may be useful in predicting areas most likely to preserve the optimum depth window for gold deposition. In the Coromandel region, regional stream sediment geochemical data has also been used to broadly define erosion levels in terms of Zn, Pb and Cu representing deeper base metal zone mineralization and Hg and Sb representing shallower cinnabar and stibnite mineralisation. The interpretations of paleodepth and potential reconstruction of paleosurfaces are limited by the paucity of data, poor age control on the paleodepth indicators and the epithermal deposits, and marked relief and complex stratigraphy in the volcanic terranes.

Jan 1, 2003

Behaviour of Bubble Clusters in a Turbulent Flow

Sep 13, 2010

By M Vendrup, T C. Christensen, C Dube

The adsorptive and granulate forming MetClean™ process has been used at many locations in Northern Sweden, Norway, Denmark, France, Spain, Mongolia, Japan and Australia. It has been pilot tested and used in full scale treatment plants to remove metals from:mine watersleachate from solid waste in incineration flue gasleachate from fly ash damsleachate from landfill and waste ponds.The following paper provides details of pilot and plants tests on the effectiveness of MetClean™ in removing arsenic, antimony, barium, cadmium, copper, molybdenum, nickel, radium, uranium, vanadium and zinc. Results show that MetClean™ may reduce the concentration of these metals in treated effluent water to the one part per billion (ppb) range.The paper also finds that, for specific metals, the optimal adsorption condition depends on the:pH levelmolar relation between the specific targeted metal and the addition of iron (II) or manganese (II)type of oxidation agentssalinity levelpresence of other metals.The most effective pH level varies according to the targeted metal but falls within the pH 5 to pH 11 range. A compromise pH level may be set when more than one metal is targeted for removal at the same time and through only one process step. The removal efficiency of one or both metals may be affected by operating at a compromise rather than optimum pH level.The MetClean process generates non-hazardous solid waste. Waste can then be disposed of more easily than brine or sludge.CITATION:Christensen, T C, Vendrup, M and Dube, C, 2015. Pilot tests for heavy metals removal in mine water, in Proceedings MetPlant 2015, pp 404–415 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

This paper describes a proposal to reopen the Sylvia gold mine for underground exploration and development for an initial production of 10 000 tpa. A combination of trackless mining equipment and railtrack would be utilised for development with ore extraction being carried out by undercut and fill methods. The use of the smallest LHD units for mucking, and rail track for the main haulage together with airleg drilling will form the basis for development and stoping. The proposal has been subjected to an environmental impact assessment report to evaluate the impacts of the proposal on the natural and social environment in the area.

Jan 1, 1987

Bacterial Leaching of Complex Polymetallic Sulfide Ore The work described here concerned the study on bacterial leaching of complex sulfide minerals and polymetallic ores operated in shaken flasks and small-scale columns. The bioleaching of jamesonite was not accessible. The iron extraction in pyrrhotite leaching reached 98.2 per cent after 23 days. After 26 days, the zinc extraction of marmatite reached 92.3 per cent while the iron extraction only reached 13.6 per cent. The pulp density had effect on the metal extraction of pyrrhppite and marmatite. For complex polymetallic sulfide ores, after 10 days in shaken flasks, 97.1 per cent zinc extraction was achieved. While after 60 days in small-scale column, the zinc extraction only proceeded to 7.8 per cent; By SEM and EDXA of experimental samples and their leaching residuum, the bioleaching mechanism was discussed.

Sep 13, 2010

By May J. R

Exploration, including research, has fuelled the enormous expansion of the Australian mineral industry in the last three decades. Analysis of success and failure in exploration and research has therefore potentially powerful lessons and messages which may be used to influence the future shape and direction of the mineral industry. Research has been an integral part of organised corporate mineral exploration since its beginnings in Australia in the 1930s. In corporations, the activity generally called project generation or new project development is the main expression of exploration research but mostly it goes unidentified and poorly documented except perhaps when a successful discovery is made and reported on. The competitive nature of exploration means that extended and detailed analysis of corporate exploration research across the industry is impossible to achieve.

Jan 1, 1992

The usual metallurgical, engineering and administrative activities associated with the handling and smelting of ores, and the subsequent handling and treatment of the products of smelting, present also problems of hygiene that engage the earnest attention of executives in all well-managed concerns.Again, associated with the employment of any considerable number of men, there is always present the problem of accident prevention.INDUSTRIAL HYGIENE.In the earliest records of lead min.ing and smelting there are references to the injurious effects of lead oh the health of the employees, and, with the advancement of medical science, lead poisoning has been the subject of many works by various authorities in many countries.Moreover, in practically every civilised country, there are laws governing the conduct of the lead industry, and in most cases these laws stipulate that employees shall receive compensation for disability caused by lead poisoning.This provision gives the problem an economic aspect. Apart from the legal and the economic aspects, however, there is the humanitarian aspect, which implies that the...

Jan 1, 1937

In a field test at Mount Isa Mines Ltd., a system developed by ICI Australia Ltd. for bulk loading "MOLANITE", an ammonium nitrate slurry blasting agent into ring drilled holes of wblcvel open stopes, was shown to be satisfactory. The fragmentation produced by the slurry was a significant improvement over ANFO and the stope production rate was increased by approximately 50%. Indications are that the charging rate and labour costs will not be greatly changed if a slurry system is used.

Jan 1, 1973