Search Documents

On Tuesday evening, February 21st, a reception of visiting societies was held in the Windsor Hall. Hon. George Irvine, Q. C., President of the General Mining Association of the Province of Quebec, occupied the chair, and, after welcoming the guests of the occasion in the name of that Association, introduced Mayor Desjardins, who expressed a cordial greeting for the city of Montreal. After appropriate acknowledgements from the President and the Secretary of the Institute, President Birkinbine delivered his presidential address. The first regular session of the Institute was held on Wednesday morning, February 22d, in the Physics Building of McGill University, where all succeeding sessions were also held. The annual report of the Council was read, as follows : Annual Report of the Council. In accordance with the rules, the Council makes the following report to the Institute:

Jan 1, 1893

By Albert D. Brokaw

The accompanying charts are presented to extend and improve a chart published under the title "A Chart to Provide Approximate Correction for Temperature and Deviation from Boyle's Law."' The applicability of this earlier chart was limited by the fact that it was based on the work of Burke and Keyes² and Kvalnes and Gaddy3 whose experiments were conducted with pure methane, the adjustments suggested for natural gases of higher specific gravity were unsatisfactory except within limited ranges of temperatures and pressures, and precise interpolation was difficult. The extensive work of G. G. Brown, D. L. Katz and their associates on the heavier natural gases has provided better bases for the needed corrections, and the present charts. which are based largely on their work, are intended to simplify the computations involved. The design of the charts has been changed by plotting temperatures as a function of pressure and correction factor, on a semilogarithmic or "ratio" grid, which gives fairly even spacing of the graphs and simplifies interpolation. Charts have been prepared for natural gas with specific gravities of .60, .65, .70, .75 and .80. The standard computation for use in estimating the quantity of gas in a reservoir may be expressed as follows: _ PA X 520 X VR ZT where: Q is the volume of gas at 60°F and one atmosphere pressure PA is the absolute formation pressure in atmospheres

Jan 1, 1949

By Albert D. Brokaw

The accompanying charts are presented to extend and improve a chart published under the title "A Chart to Provide Approximate Correction for Temperature and Deviation from Boyle's Law."' The applicability of this earlier chart was limited by the fact that it was based on the work of Burke and Keyes² and Kvalnes and Gaddy3 whose experiments were conducted with pure methane, the adjustments suggested for natural gases of higher specific gravity were unsatisfactory except within limited ranges of temperatures and pressures, and precise interpolation was difficult. The extensive work of G. G. Brown, D. L. Katz and their associates on the heavier natural gases has provided better bases for the needed corrections, and the present charts. which are based largely on their work, are intended to simplify the computations involved. The design of the charts has been changed by plotting temperatures as a function of pressure and correction factor, on a semilogarithmic or "ratio" grid, which gives fairly even spacing of the graphs and simplifies interpolation. Charts have been prepared for natural gas with specific gravities of .60, .65, .70, .75 and .80. The standard computation for use in estimating the quantity of gas in a reservoir may be expressed as follows: _ PA X 520 X VR ZT where: Q is the volume of gas at 60°F and one atmosphere pressure PA is the absolute formation pressure in atmospheres

Jan 1, 1949

F. C. LANGENBERGW.*at 8ertoivn,M ass. (written cliscussiont).-I am inclined to the view that the change in physical properties encountered in the material with which the authors are working is due to the relief of internal strains. The statement, on page 1.098 of their paper, calling attention to the fact that this phenomenon disappeared when the material was rolled into 1 7/8 -in. square billets is of particular interest. It is certain that the internal strains set lip by cooling in a small billet of this size would be much less than those produced in a billet having a larger cross-section cooling under the same conditions. The statement that the physical properties of a given test bar were materially changed by standing has been brought to my attention in connection with the testing of gun forgings. I have made a number of observations on forgings produced at Watertown Arsenal to ascertain whether any change in ductility was produced by the aging of the test specimens. The results were always negative, but this can be explained by the fact that ii gun forging is generally a forging that has been quenched and subsequently drawn at a relatively high temperature.

Jan 10, 1919

By David S. Bolin

INTRODUCTION This paper is directed toward those companies or individuals who may be considering the possibility of tin exploration or development projects in South America. Although tin deposits are known in many countries of Latin-America including Argentina, Peru, and Mexico, the majority of the deposits are located in Bolivia and Brazil. These two countries also account for virtually all the current production. Many factors affect the economic decisions related to mining and exploration projects in this region including the following: 1) Types of deposits 2) Anticipated size and grade of deposits 3) Deposit geometry and ore distribution as it affects the selection of a mining method 4) Metallurgical amenability 5) Governmental policies 6) Taxation 7) Anticipated capital and operating costs 8) Marketing costs This discussion will be directed toward each of these points. The majority of the presentation will be concentrated on Bolivia as this country is the principal producer in the region, however, the potential for further tin development in Brazil is excellent. Due to the remote and previously almost inaccessible location of the stanniferous districts of Brazil, little is known with respect to size and type of non-alluvial deposits which may exist in this vast country. TYPES OF DEPOSITS Two major types of deposits are currently being exploited in Bolivia; alluvial, and hard rock or lode deposits. Bolivia produces substantial tin from both types of deposit whereas virtually all Brazilian production to date has been from alluvial sources. Alluvial Deposits Brazil: The alluvial tin deposits of Brazil are located in river channels and flood plains adjacent to low mountain ranges. The terrain containing the tin placers is flat, marshy, and generally jungle covered. The major controls of alluvial cassiterite concentration are the ancient and present stream channels. The average tin concentration in the placers varies from 500 grams to approximately 1.0 kilograms per cubic meter. Tin reserves in the Rondonia field of Brazil have been estimated at 600,000 tons of fine tin. A bucketwheel suction dredge went into production in the Rondonia district in 1979, and four others have since been ordered. Several other gravel pump, and hand mining operations are also in production in this field. In addition to the Rondonia district, tin occurrences are known from Xingu, in Para state, and in the state of Minas Gerais. Bolivia: The alluvial deposits of Bolivia are somewhat more complex due to the variable geomorphology and abrupt topography. Conventional placer accumulations of cassiterite are found in many stream channels and intermontane basins surrounding the major lode tin producing regions. In addition to stream and valley placers, a group of deposits locally referred to as "Pallacos" or "Llamperas" which consist of colluvium, landslide debris and glacial moraine material, contain substantial tin reserves in some areas. The stream channel and intermontane basins contain the only deposits which are presently being exploited by mechanized methods. One dredge is working the stream channel below Cerro Rico de Potosi and another is operating in an intermontane basin southeast of the city of Oruro. Both of these dredges are operated by private companies. The average grade for these operations varies from 250 to 500 grams per cubic meter. The largest of the intermontane basin placers known at present is the Centenario deposit located adjacent to the Catavi lode deposit. This deposit contains approximately 170 million cubic meters of material with an average grade of about 150 grams per cubic meter. The "Pallacos" deposits are found on the slopes of mineralized areas and in glacial moraine. The mineralized material is generally completely unsorted, with tin and sometimes tungsten values distributed erratically throughout the entire mass. Most of these deposits are worked by small leasors or cooperatives; however, at least one mechanized washing plant is in operation southeast of Oruro. The size of these deposits may reach up to several million cubic yards. Grades are very erratic, but may range from 200 to 500 grams per cubic yard. In addition to the formal mining operations, virtually every drainage surrounding the major mines is being worked by independent' miners utilizing hand mining and jig or pan concentration. The aggregate production from these operations is substantial. The

Jan 1, 1982

By D. A. Farmen

INTRODUCTION In early 1978, engineering personnel at The Carter Mining Company began using photogrammetry coupled with a computer modeling technique to aid in mine planning efforts. The decision to develop this approach was based on the following needs: 1. A method to accurately capture excavated quantities for reporting purposes, 2. A method to produce accurate up-to-date maps for planning purposes, and 3. A computer-based mine-planning technique that would be compatible with techniques used in the past. The system developed utilizes a photogrammetric contractor to provide thousands of aerially-surveyed data points for input into the computer system. Each month the Rawhide and Caballo mines are flown by the photogrammetric contractor. The terrain of the active pit area is digitized and punched out on computer cards. This information is read into The Carter Mining Company's computer facilities, and an updated two-dimensional topographic grid model of the pit is generated. This surface is used to generate quantities moved during the month, to update isopachs, and to update quantities contained in fixed block progression polygons used for forecasting purposes. The system has greatly reduced the amount of manhours spent in field surveying and provides a useful tool for expeditiously evaluating many different forecast cases. It also provides the

Jan 1, 1983

By Campbell Hunter

PETROLEUM is found in almost every province in Persia. On the northern frontier, along the southern shore of the Caspian Sea, it is found near Anzelli and Shakhtesar and gas at Khoremabad. Oil is also found at Gumush Tepe, northwest of Astrabad, on the southeastern shore of the Caspian Sea. Further inland, to the south of Astrabad, oil is found at Schahkuh-i-balae, also on the margin of the Khorasan desert at Semnan, 115 mi. (35 m.) east of Teheran. Along the western frontier, from northwest to southeast, oil is encountered at Ouschachi, north of Lake Urumieh; in the province of Azerbaijan, at Zohab, Khanikin, and other places in the district of Kormanshah in the province, of Ardelan. Further south, in the province of Luristan, oil is found east of Mendeli and in the Pusht-i-kuh districts. Considerable quantities of oil are also obtained from Schuster, Maidan-i-Naphtun, Ram-Hormuz, Beheban, which are almost on a straight line, running northwest and southeast along the foothills of the Bakhtiari Mountains. At Ahwaz, in the province of Arabistan, oil has been found along another range of hills whose axis also lies in a northwest-southeast direction. In the Fars province, boring for oil has taken place at Daliki, and indications of oil are found at Kheri, Fasa, Darab, and other places. A gas show is also recorded at Kuhi-Sung-Atush in this province, 30 mi. (48 km.) east of Darab. In the south of Persia, oil is encountered on. Qishm Island, also at Ahmedi and other places north of Bunder Abbas. On the southeastern frontier, oil is found on the Sarhad range of hills. Thus, oil indications have been noted over a distance of approximately 1100 mi. along the western and 700 mi. along the northern frontiers of Persia.

Jan 2, 1920

By G. C. Rauch, T. H. Courtney, J. Wulff

The superconducting behavior of Nb-Ti alloys containing 40 and higher wt pct of Nb and variable oxygen content was studied as a function of thermomechanical processing. Critical current density (Jc) us applied transverse magnetic field (H) data were obtained for 0.010 in. diam wires at 4.2° Kin steady fields up to 120 kOe. The precipitate responsible for increase in Jc in each of the alloys studied was related to niobium and oxygen content. In alloys containing 40 to 60 wt pct Nb with less than about 1600 ppm of oxygen, w precipitation in the range 350° to 450°C appears to be responsible for the maximum value of Jc observed. In alloys of higher oxygen content (-2500 ppm), the oxygen-enriched a phase which precipitates in the temperature range 450° to 550°C is a more effective fluxoid pinner. Maximum Jc in low oxygen (350 ppm) 80 wt pct Nb alloys was achieved by 600°C aging heat treatments. Measurements of resistive critical field also reflect the changes in composition accompanying precipitation in these alloys. It is well known that the superconducting critical current density, Jc, of solid solution superconducting alloys can be increased by precipitation heat treatments.1-4 The precipitate, to serve as an effective superconzlucting fluxoid pinner and increase Jc, must be of proper size and spacing.' Its electronic properties must also be different from those of the matrix.6 As in age-hardenable systems, optimum temperature and time of aging are dictated by the composition and history of the particular solid-solution alloy under consideration. The alloy diagram of Ti-Nb7-9 shown in Fig. 1 is typical of ß-stabilized Ti alloys. Precipitation to achieve high Jc in Ti-Nb and Ti-Ta alloys is usually carried out in what is believed to be a two-phase a + ß region.1,2,4,10 Previous work on Ti-Nb4,11 and on other ß-stabilized systems such as Ti-V, Ti-Mo,12-14 has shown, however, that the first precipitate to appear is not necessarily (Y. Under specific conditions the meta-stable w phase is precipitated instead. A further complication arises in such alloys from the strong influence of contained oxygen on the phase stability and on the kinetics of precipitation.15,16 The superconducting critical current density of Nb-Ti alloy containing less than 36 wt pct Nb has been studied by Vetrano and Boom1 and Kramer and Rhodes.4 The most effective aging temperature was found to be about 425°C; fluxoid pinning was attributed to the precipita- tion of a by Vetrano and Boom and of w by Kramer and Rhodes. Although the latter workers used recrystal-lized material and the former cold-worked, studies carried out in our laboratory lead us to believe that the type of precipitate responsible for increased Jc is unaffected by prior cold-work.17 That other types of precipitates may also be effective, especially in higher oxygen-containing alloys, has been demonstrated by Reuter, et al.2 in this laboratory with the aid of electron microscopy. Reuter et al. found that at an aging temperature of 600°C, fee-TiO is precipitated, resulting in high values of Jc. Even higher values of Jc were observed after heat treatment at 500°C, but the precipitate could not be indexed as fee-TiO. Whether the precipitate was oxygen-rich w or a could not be clearly distinguished. The work nevertheless indicates that appreciable amounts of oxygen alter the nature of the phases precipitated at different temperatures, at least in alloys containing more than 36 wt pct Nb. Since such compositions are more readily worked into suitable wire than lesser niobium content alloys, it was decided to study the response to aging of the alloy compositions reported in the present paper with the hope of clarifying the effect of composition on the precipitation processes responsible for high values of Jc. I. EXPERIMENTAL Nb-Ti alloys containing 40, 50, 60, and 80 wt pct Nb were prepared by are-melting 35 g ingots of iodide crystal bar titanium and electron-beam melted niobium.

Jan 1, 1969

By S. F. Ravitz

In his excellent book on the Principles of Flotation, Warkl makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent float-ability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter2 presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism.l(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirin their results. The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen Pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally Pure galena was crushed by hand on a clean bucking board, screened to —I50+ 200 mesh, and deslimed on a 200-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1943

By S. F. Ravitz

In his excellent book on the Principles of Flotation, Warkl makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent float-ability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter2 presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism.l(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirin their results. The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen Pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally Pure galena was crushed by hand on a clean bucking board, screened to —I50+ 200 mesh, and deslimed on a 200-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1943

By J. W. Dougherty, J. M. Douglas

THE Hollinger gold mine is in the Porcupine mining division, District of Cochrane, in the northern part of the Province of Ontario. The adjacent town of Timmins, with a population of 25,119, lies 490 miles by railway north of the city of Toronto. GEOLOGY The property is situated on the northwest limb of a major syncline, which pitches northeast at approximately 50°. The principal rocks of the Hollinger area are of pre-Cambrian age and consist of altered, schistose, Keewatin lava flows intruded by stocks of schistose, quartzfeldspar porphyry generally assigned to the Algoman period. The structure of the Keewatin series is extremely complex as a result of close folding and some faulting. The schistosity, trending north 70° east and dipping steeply to the southeast, is most highly developed along a subsidiary anticline in which the major porphyry bodies occur. The ore bodies, which exhibit three principal structures, consist of quartz veins and associated pyritized wall rock. Some lodes are composed of en echelon veins, others exhibit a main quartz body with branching stringers and a third consists of a single definite lead. Gold, in a coarse visible form, may be confined to quartz in some ore bodies but in others it is finely divided and is found not only in quartz but also associated with pyrite in the adjacent wall rock. In many veins the distribution of gold is such that there are several ore sections, separated by areas of low-grade material, in the same vein although its physical appearance remains unchanged. The veins form a very complex pattern in an ore zone which in places attains a length of 6000 ft. and a width of 4000 ft. They are most abundant in the Keewatin lavas in the neighborhood of the porphyry bodies. Few of the veins are persistent for long distances, though some

Jan 1, 1940

By B. E. Sundquist

The various methods based on solution models for obtaining free energies of mixing from miscibility-gap data have been applied to a number of binary-alloy systems. For nine of these systems there exist experimental thermodynamic data that permit a comparison of the results to experiment. It was found that the method of van der Toorn and Tiedema almost invariably leads to results that are physically unacceptable and that vary drastically with small changes in the miscibility-gap parameters. The subregular solution model is found in all cases, except the Al-Zn, Fe-Cr, and Cu-Pb systems, to exaggerate the free energy of mixing by 30 pct or more. The model developed by Lumsden is found to give results that are often in excellent agreement with experiment and which exaggerate the free energy of mixing by no more than 30 pct. These results and others give evidence that the Lumsden treatment of the effect of unequal atomic sizes and of imperfect configurational randomness due to deviations of AB bond energies from the mean of AA and BB bond energies is adequate for most systems. ANALYTIC expressions are frequently proposed for the dependence on composition of the activities of the components of a solution. Because the development of solution theory is incomplete, these expressions contain parameters which must be determined by experiment. The measurement of activities is often difficult and consequently such measurements are less readily available than are measurements of phase equilibria which, under certain conditions, can also be used to evaluate these parameters. For example, suppose it is known that two structurally dissimilar phases, each of known composition, in an n-com-ponent system are at equilibrium at a given temperature and pressure. n equations can be set up in terms of these parameters expressing the equality of the chemical potential of each component in the two phases. In addition, one can write the Gibbs-Duhem equation for each phase that also contains these parameters. Thus, if these n + 2 equations contain n + 2 parameters, these parameters can be determined (at the temperature in question) from the phase diagram alone. If the average number of parameters in each expression for the activity of a given component in a given phase is V then there will be 2nV parameters involved. Equating 2nV to n + 2 shows that, for n + 2, V = 1. If the temperature dependence of each parameter were to be expressed in some explicit form one could use equilibrium conditions at a number of temperatures to increase V. The situation is much improved when the two phases in equilibrium are structurally similar. It can then be assumed that, stably or metastably, two phases will become one at higher temperatures. Thus the number of parameters involved becomes nV instead of 2nV. Hence, V = 2 for n = 2 using only one temperature. (It is implied here that the activity expressions used are valid over the entire composition range.) In this investigation only the equilibrium of two structurally similar, two-component phases (miscibility-gap systems) will be considered. The various proposed solution models will be applied to a number of these systems and the results compared with available experimental results. All of the analytic expressions that have been proposed for the free energy of mixing of a two-component system are of the form where ?Gmix is the free energy of mixing per mole of solution, N1 and N2 are the mole fractions of components 1 and 2, respectively, and f(Ni, T) is some function of composition and temperature. In the "ideal" solution model f = 0. In the "regular" solution model f = a constant. Since these two models permit only a symmetric equilibrium diagram they will not be considered further here. The simplest model that permits a nonsymmetric miscibility envelope is the so-called "subregular" solution model proposed by Hardy.1 This model gives where the Ci(T) are functions of temperature only. The same expression for f is obtained from the "linear a function" model proposed by Darken and Gurry2 and applied to miscibility-gap systems by Wriedt.3 This model requires that the a function defined by be a linear function of composition (yi is the activity coefficient of component i). This model is not purely hypothetical for it has been found2 to hold true for a number of systems. It is readily shown3 that the f(Nl, T) obtained from this model is of the form given in Eq. [2]. It will be noted that the subregular solution model contains only two parameters and hence both of them can be determined at any desired temperature below the critical temperature, Tc, for a miscibility-gap systems in the manner described previously. At T, the two constants can be determined by equating the second and third derivatives of ?Cmix with composition to zero. Another two-parameter model was proposed by Lumsden4 who set

Jan 1, 1967

By J. W. Putman, N. J. Grant, D. S. Bloom

SEVERAL recent determinations of the melting S point of pure chromium have been reported which give values of 1845°C1; 1895°C,² 1930°C,³ 1860°C,' and 1890°C.5 because of this wide spread of values, it appeared desirable to make one additional attempt to obtain a more accurate, reliable figure. bloom and Grantx recently reported a phase transformation in chromium:.--- it was desired to check this, too, in the course of checking the melting point. To accomplish this, a much higher purity chromium was required. Electrolytic chromium containing about 0.5 pct 0 was crushed to a finer size and was then annealed in highly purified, dried hydrogen at 1375°C for 100 hr. This treatment produced chromium with about 0.008 pct 0, 0.002 pct N, and negligible carbon. The balance of the impurities was 0.3 pct Fe, 0.03 pct Si, 0.004 pct S, and less than 0.001 pct Mo. This chromium was melted in a stabilized zirconia crucible under pre-purified argon, using induction heating. Temperature measurements were made with annealed wolfram-molybdenum thermocouples and a Leeds and Northrup Speedomax Recording Potentiometer. The thermocouples were annealed for 1 min in hydrogen at a temperature of about 2400°C. Each leg of the thermocouple was immersed in an ice-water mixture using mechanical connectors to the lead wires. The thermocouple tip was immersed in the molten chromium in a zirconia protection tube which introduces an error of about 3°C as a temperature drop through the walls of the tube. The weight of chromium was about 183 g. The dimensions of the melt in the crucible were about 1.25 in. diam x 2 in. high. The tip of the thermocouple was held about ½ in. from the bottom of the crucible. Two new thermocouples were used with the above set-up giving the results shown in Table I. Since this chromium is purer than that used by Greenaway, Johnstone and McQuillan,' by Carlile et al.,4 and other investigators,²,3 it is believed to be the more accurate. Thermocouple aging effects which are believed responsible for the high value of 1930°C³ were avoided in this work. This value of 1903°C is correct to about ±10°C. The right hand column lists the temperature of the a ? ß transformation on heating and the ß ? a on cooling.3 A sample curve is shown in Fig. 1. The value so determined is 1840°C + 15°C. Fig. 1 gives adequate evidence that there is a transformation in chromium at high temperatures.' References 'H. T. Greenaway, S. T. M. Johnstone, and M. K. McQuillan: High Temperature Thermal Analysis USing the Tungsten-Molybdenum Thermocouple. Journal Inst. Metals (November 1951) 19, p. 109. ²J. W. Putman, R. D. Potter, and N. J. Grant: The Ternary System Chromium-Molybdenum-Iron. Trans. A.S.M. (1951) 43, p. 824. ³D. S. Bloom and N. J. Grant: Chromium-Nickel Phase Diagram. Trans. AIME (1951) 191, p. 1009; Journal of Metals (November 1951). ' S. J. Carlile, J. W. Christian, and W. Hume-Rothery: The Equilibrium Diagram of the System Chromium-Manganese. Journal Inst. Metals (1949) 76, p. 169. 5G. Grube and R. Knabe: Ztsch. Elektrochemie (1936) 42, p. 793.

Jan 1, 1953

By I. R. Kramer

The apparent activation energy, U, JOY plastic deformation of aluminium, copper, and gold single crystals and polycrystalline aluminum was found to he dependent upon surface condition. At low strains, the value for U for aluminum single crystals was 4200 cal per mole ; however, this value decreased to 920 cal per mole when the specimens were polished during the test at a rate of 50 X 10-5 win-1 The activated volume also was found to increase with the rate of metal removal. That the surface plays an important role in plastic-deformation processes has been adequately demonstrated.1-4 Of particular interest at this time are the observations4 that the creep rate of single crystals of fee metals is increased markedly when specimens are polished during the deformation process. These observations were interpreted in terms of a dislocation debris layer at the surface regions of the crystal. This layer, which appears to be a region containing a high concentration of dislocations or segments of dislocations, not only will impede the egress of dislocations on the primary slip system, but will also provide a barrier against which dislocations may pile up. By this means, a stress which opposes the motion of dislocations will be generated. It is considered that this stress must be taken into account in any theory which describes the plastic-deformation process. Although a detailed dislocation model cannot be given at this time, it may be stated that the stresses opposing the motion of dislocations arise from the dislocations in the debris layer, Ts, and ti due to the resistance to motion imposed by internal obstacles such as Lomer-Cottrell barriers, subgrain and grain boundaries, forest dislocations, and so forth, as well as the resistance due to the presence of jogs on dislocations and the interaction of the stress fields of dislocations, and so forth. In essence, we have added an additional term, ts, to the usual form of the equation T = Ta- Tb, where Tb is the back stress due to the various types of obstacles which impede the motion of dislocation. Accordingly, the net stress, t, acting on a dislocation may be written as where Ta is the applied shear stress. For deformation which occurs by a thermally activated process5,8 ?=Ae-u/kT = A e(u,-VT)/kT [2] and U = Uo- Vt PI where U = activation energy for plastic flow, y = shear strain rate, Uo = activated energy for plastic deformation in the absence of stress and depends upon the particular deformation process, V = activated volume, k = Boltzmann constant, T = temperature, OK, and A = frequency factor. From Eqs. [I] and [3], U = Uo- V(Ta - Ti - TS) [4] and it is seen that if Ts decreases, the activation energy, U, must decrease if V remains constant. However, as will be shown, V is a function of the surface conditions. In their work on aluminum, Lytton and coworkers7 reported that at low strains the activation energy was 3400 cal per mole and at high strains it was 28,000 cal per mole. The lower value was interpreted in terms of the energy necessary to overcome the Peierls force, while the higher value was associated with the energy necessary for dislocations to move by a cross-slip process. It will be shown that the lower activation energy is associated with the surface debris layer rather than with the Peierls force. EXPERIMENTAL PROCEDURE Single crystals having a nominal cross section of 1/8 in. and a 3-in. gage length were prepared by a modified Bridgman technique using a multiple-cavity graphite mold. The initial purity of the metals was 99.997, 99.999, and 99.999 pet for aluminum, copper, and gold, respectively. The orientation of the specimens is given in Fig. 1. The measurement of the activation energy as a

Jan 1, 1964

By D. C. Jillson

WORK in recent years1-' has indicated a complexity of the processes of deformation of metal crystals not previously appreciated and not fully accounted for by any hypothesis so far advanced. Furthermore, the nature and mechanism of formation of nuclei of recrystallization have not been determined precisely. The deformation of single crystals of zinc has been studied frequently, but the purity of the zinc and the perfection of the specimens sometimes have been given little consideration. Methods have been developed recently that readily yield zinc single-crystal specimens of high quality.5 In the present work, such specimens were deformed in various ways under various conditions, and deformed specimens were annealed to obtain information regarding recovery, recrystallization, and grain growth. The paper attempts to correlate and evaluate previous data, as well as to present new data, in order to determine areas in which more detailed work might be done most profitably. Tests at temperatures from the freezing point (419.46°C) to room temperature revealed glide only on basal planes in a close-packed direction (100)*, as reported by Mark, Polanyi, and Schmid6 and others. Markings probably similar to those observed by Kolesnikov7 and Boas and Schmid8 were noted in specimens stretched at elevated temperatures, but it seemed clear that these were not caused by prismatic or pyramidal slip (see second paragraph of section on Phenomena Involving Bending of the Basal Plane). Twinning Twinning on the octahedral plane of a face-centered cubic metal has been pictured as a process of simple homogeneous shearing along that plane in a [112] direction. It was recognized by Mathewson and Phillipsv and others""" that the (102) twinning of zinc required a somewhat more complex mechanism and might be considered as a homogeneous shearing of (102) planes in a [211] direction plus slight adjustments of atoms to positions of greater stability or lower energy, or as a single movement of each of the atoms in the same sense into the final positions. Gough and Cox" modified Mathewson's mechanism to obtain a more stable lattice configuration, but it is not clear that they succeeded, and their mechanism requires movement of some of the atoms in a sense opposite to that of the overall twinning movement. They also suggested that twinning may occur as a result of previous basal slip. This conclusion was based on the observation that twinning caused by alternating torsion was clearest and most profuse at positions for maximum basal slip rather than for maximum stress on (102) planes in the close-packed direction (not the twinning direction), and no mechanism was described. It might be wondered whether resolution of stresses on the twinning plane in the twinning direction would have afforded a simpler explanation. If twinning is essentially a simple homogeneous shearing along the twinning plane, it would seem that twins should grow by a smooth, continuous mechanism, and, indeed, that a simple reversal of stresses should reverse the shearing and de-twin the crystal. Cylindrical tablets 1/8 to 1/4 in. thick were cleaved from singlle-crystal specimens and were squeezed, perpendicular to a second-order prism plane, to give a tensile stress perpendicular to a first-order prism plane. A "click" was heard and a thin, needle-like twin appeared on the basal cleavage face. If squeezing was continued smoothly, the twin, viewed at magnifications up to X500, grew smoothly and quietly (fig. 1). X-ray examination verified that the twinning was of the (102) type. Rotating the compression axis 90" to reverse the stress then caused a smooth, continuous shrinkage and ultimate disappearance of the twin (fig. 2). The squeezing also caused a rumpling of the basal

Jan 1, 1951

By F. Lawson, N. A. Sareyed-Dim

A rotating disk of iron precipitant in a high temperature batch reactor has been used to study the kinetics of precipitation of nickel from low concentration aqueous solutions. Under inert atmosphere conditions, for temperatures up to 150°C, the rate of nickel deposition at pH25°C of 5 to 6 is controlled both by the rate at which nickel ions reach the surface and the rate of chemical reaction at the surface. However, the presence of oxygen in the atmosphere above the reacting system increases the nickel deposition rate dramatically. It is suggested that under the experimental conditions used, hydrogen atoms are adsorbed on both the iron and nickel, thus reducing the number of sites available for the cementation reaction. Oxygen acts as a depolarizer for hydrogen.

Jan 1, 1977

By J. Wright, R. J. Tyler

Changes in the pore structure of hematite pellets during reduction to iron were investigated under a variety of experimental conditions. Pore structures were determined by a mercury penetration technique. The reduction temperature was found to be the major influence on structure, the pore system being bimodal below 7.50°C and unimodal above 900°C. Pore sizes ranging front 0.04 to 20 m were observed in complete metabolized pellets produced over the temperature range 650 - 1050°C. Gas composition and reduction rates also influenced the pore structure of the metabolized pellets, although to a lesser extent than the reduction temperature. An apparent activation energy of 24 kcal/mole was derived for the pore formation process.

Jan 1, 1979

The thirty-ninth meeting of the Boston Section was held at the Engi- neers? Club on Monday evening, Dec. 4, 1916. Thirty-three members and guests sat down to dinner; There were present as section guests; Dr. L. D. Ricketts, and Prof. Bradley Stoughton, President and Secretary of the parent society, and each was called upon to speak. Mr. Stoughton spoke of the growth of the Institute during the past year and described the very numerous and important activities, of which the junction of the American Society of Civil Engineers with the other three societies is perhaps the most important. Dr. Ricketts, the advertised speaker of the evening, spoke on Recent Progress in Mining and Metallurgy of Copper Ores. In discussing the improvements in mining, he traced the mining methods from square- set mining to the modified Ohio System now so successfully used at Inspiration: In metallurgy, he described the growth of reverberatory-smelting ant1 allied problems such as the utilization of the waste heat for generating steam. He laid stress on the importance of sampling and bedding of

Jan 6, 1917

By C. B. Daellenbach, T. D. Tiemann

The prevention of quartz flotation by chelation of activating ions with the tetrasodium salt of EDTA in oleic acid flotation was investigated using a small vacuum flotation cell. It was found that flotation of quartz could be entirely suppressed in the presence of activating ions during complete flotation of hematite. It was further shown that the concentration of activating ions liberated from Wisconsin Gogebic taconite is sufficient to float quartz in an oleic acid system. Large tonnages of low grade siliceous iron ores occur on the iron ranges of the Lake Superior district. Although the lower grade nonmagnetic types are currently not of economic importance, they constitute a large future potential source of iron and steel, and hence have been the subject for extensive research on their beneficiation. TACONITES Of particular interest to the Dept. of Minerals and Metals Engineering at the University of Wisconsin have been the low grade nonmagnetic taconites of the Wisconsin Gogebic Range. These occur as five members of the iron formation and have been described in detail elsewhere.' Essentially they consist of an intimate mixture of hematite, goethite and quartz, with minor amounts of siderite, magnetite, iron containing silicates, and manganese minerals. A typical mean analysis based on the Bureau of Mines analyses' is: SiO2-52.50%, Fe2O3-43.40%, (Fe-30.38%), A12O3-1.15%, P2O5-0.07%, Mn2O3-0.29%, CaO-0.07%, (S-0.03%), Loss on ignition-2.00%. The quartz in these ores is of a microcrystalline variety,2 and so intimately associated with the iron oxide minerals that extremely fine grinding, in the order of minus 325 mesh, is required for liberation. During grinding and subsequent flotation, the concentration of quartz activating ions in the pulp becomes sufficiently high to activate quartz which floats along with the iron minerals in the presence of oleic acid. cook3 and co-workers concluded that oxidized iron ores released appreciable quantities of quartz-activating ions in water pulps. This is shown to be true in the present investigation. As a matter of fact, application of this phenomenon, as well as the intentional addition of activating calcium ions, is made use of in the an ionic flotation of silica from the iron oxide minerals.4,5 In view of the above, it becomes almost impossible to effect a sharp separation of quartz in the oleic acid flotation of the iron oxide minerals from these taconites, even with satisfactory liberation. This fact led to the current investigation to find a means of linking the activating ions with a chelating agent. The aim was to establish basic data for the quartz-water-oleic acid system which might not only be applicable to iron ores, but also to the flotation of other siliceous ores as well. EXPERIMENTAL METHODS Vacuum Flotation Cell: The vacuum flotation used in this investigation is similar to that used by previous investigators.6,7,8 The cell consisted of a 100 ml graduated cylinder with the lip removed. Vacuum from a water aspirator was applied to the cell through a trap; suitable tubing, and a rubber stopper inserted in the top of the cell. Constant absolute pressure was maintained by means of a manometer connected to the trap with a tee. Flotation: The required amount of activating ion solution was pipetted into a beaker. This was then diluted to 99.0 ml with water having a pH below that desired for the test, or so adjusted with HC1. After addition of 1.0 ml of oleic acid solution (2.0 mg oleic acid per ml), the pH was readjusted to the desired value with NaOH, and the entire solution transferred to the cell containing 1.5 gm of quartz. After vigorously agitating the cell and its contents for 2 min, the vacuum was applied to the cell and the estimated degree of flotation observed for a 3-min period. Activating ions studied included Ca++, Mg++, Al+++, and Fe+ + + added as chloride solutions. In addition,

Jan 1, 1964

Florida State Geological Survey, Tallahassee, Fla Herman Gunter, State Geologist A list of publications will be sent upon request Citizens of the state may obtain publications available without cost, others may have them for postage, or they can be sent express collect Twenty Annual Reports have been issued from 1908 up to and including the 21st-22nd Annual Report (1931). Only three are now available; 4th Annual Report (1912), 15th (1924) and 18th (1927) Reports since 1921 contain statistics on mineral production. All reports contain papers on various subjects, many of which are still available separately, and are so indicated in the list of publications. Seven bulletins have also been issued, principally of interest to paleontologists Bulletin 7, The Pensacola terrace and associated beaches and bars in Florida (1931), is of more general interest Bulletins will be sent upon receipt of postage. Thirteen Press Bulletins, most of which are available, have also been issued, but are of minor interest

Jan 1, 1933