Search Documents

By W. T. Ober

the hammering effect acts only to a point 3 in. back from the cutting edge, and the hardening heat extends back only 1 in. from the cutting edge. Then, as a steel is taken from the fire, the grain condition is as shown in Fig. I. After the forging operation has been performed the condition shown by Fig. 2 exists. The heating operation to harden the cutting edge produces the effect shown in Fig. 3. The questions that naturally arise are: Will the cost of the extra heat treatment necessary to change this condition (annealing) be more than the saving that may be effected in the drill steel or will the extra heating be an economical as well as a wise thing to do? Is this condition necessarily detrimental to the maximum service of the drill steel? Can this annealing action be obtained in the hardening heat by heating more of the bit, say at least 5 in., to the hardening temperature but quenching only the end of the bit by a shallow immersion? Short Rock-drill Steels Reclaimed by Welding By W. T. Ober, Lynn, Mass. Experimental tests by the Thompson Company have shown that short lengths of rock-drill steels may be reclaimed by electric butt welding. The drills used in the experiments were hollow drills l1/4-in. in diametcr containing 0.95 per cent. to 1.05 per cent. carbon. The ends to be joined must first be ground off fairly square and the greater part of the rust, scale, etc. removed for 3 or 4 in. back in order to insure good electrical contact with the dies of the welder and countersunk, with an 80° countersink, approximately 1/4 in. The steels are then clamped in the copper dies of the welder, so that a length projects from the inside edge of each pair of dies equivalent to from one-half to three-quarters the diameter of the drill. The drills should also be brought into accurate alignment. The first step is to bring the ends into close proximity and then close the primary circuit of the transformer, slowly bringing the steels together until their ends lightly touch, when they will "flash," that is, minute

Jan 1, 1922

By G. W. Poling

Chemical and physical properties of thiol collectors are re-examined to compare the prospects,of heavy metal-thiolate or disulphide surface reaction products acting as actual collector species. Recent evidences for the existence and importance of each of these types of adsorbed species on sulphide minerals are also discussed. A conclusion is reached that partial coverage by chemisorbed heavy metal thiolate is often sufficient to confer practical levels of hydrophobicity and floatability. Only on a few highly conducting and "noble" sulphides does adsorbed disulphide-type collector oxidation product appear to be significant.

Jan 1, 1976

By Robert H. Richards

It will hardly be worth while to spend time over the discovery of this mine, how lumps of galena were picked up and brought to town, and how legends were told of an old mine from which Revolutionary bullets were made. This is an entirely new mine, with no evidences of former or ancient workings in its immediate vicinity to guide or attract the prospector. The first pit was opened in May, 1874. In August I made a visit to this pit, which was 6 feet wide in the northwest direction, 12 feet long north 80° east, and 6 feet deep..About 4 tons of a galena carrying gray copper, siderite, and quartz, had been taken from this pit. The lumps were all of them evidently float specimens, and varied from 8 to 12 inches thick, and showed very distinct indica-

By Wayne Loel

THE application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and under varying climatic conditions, Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarine geology. Aerial photographs with accompanying geologic maps are shown to illus-trate the appearance from the air of different geologic features under varying climatic and topographic conditions.

Jan 1, 1938

University of Alaska College, Alaska Mining Society (Inactive) H. G. WILCOX, Faculty .Sponsor University of California Berkeley, California Mining Association. OLEG D. SCHERBININ. President CHARLES S. PRATT, Secrctary LESTER C. UREN, Faculty Sponsor

Jan 1, 1944

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By E. C. Wright

The bessemer process is nearly one hundred years old. William Kelly, the American inventor, was able to demonstrate that he had accomplished the pneumatic purification of molten pig iron as early as 1847; Henry Bessemer's English patent was granted in 1855. The application of this steelmaking process since then and the present position of bessemer steel are concisely discussed on pages 355 and 356 of the fifth edition of "The Making, Shaping and Treating of Steel." The great expansion of the automotive, machine-tool, chemical and oil industries after I9I0 opened up a large market for special steels, whereas the output of steel before that time was mainly for structural purposes. The need for building more blastfurnace capacity complementary to bessemer operations, combined with the availability of the' necessary amounts of steel scrap, both contributed to the extension of open-hearth plants at the -exense of besskmer capacity. The ability of the open-hearth furnaces to consume virtually all types of raw materials as far as phosphorus content is concerned, and the need for selecting low-phosphorus ores of rapidly decreasing sources for the bessemer, also played a part in the reduction of bessemer steelmaking operations and the increase in basic open-hearth plants. As a consequence, the proportion of bessemer steel made, in this country decreased from 65.7 per cent of the total in 1900 to 37.1 per cent in 1910, and only 6.8 per cent of the total in 1937. The metallurgical concepts existent between 1910 and 1920 caused the writing of many specifications of very low phosphorus and sulphur content, which definitely barred bessemer steel from many commodities. Now sulphur is being added to many open-hearth and bessemer steels in amounts far exceeding the maximum sulphur content of good bessemer steel. Re-phosphorizing is also widely practiced for several specific applications. Even today, the chemical-analysis limits of many important steel specifications have an arbitrary and archaic tinge. The old standard "0.30 to 0.60 per cent manganese" might be mentioned in this connection as similar to the rigid requirements for maximum sulphur and phosphorus that were established at least 25 years ago. The literature is full of vague and complee discussions of the effects of nitrogen and oxygen where these elements existed in steel in amounts less than 0.02 per cent. Many failures have been attributed to these elements without reasonable proof on which to base the conclusion. Methods of determining oxygen in steel require such complicated equipment that only a few research laboratories have the required apparatus. Even so, the accuracy of oxygen determinations in steel has been only recently reproducible. Up to the present time, no one has succeeded in obtaining a sample of molten steel that accurately indicates the full oxygen content of the metal in the furnace or ladle because the molten sample

Jan 1, 1944

By E. C. Wright

The bessemer process is nearly one hundred years old. William Kelly, the American inventor, was able to demonstrate that he had accomplished the pneumatic purification of molten pig iron as early as 1847; Henry Bessemer's English patent was granted in 1855. The application of this steelmaking process since then and the present position of bessemer steel are concisely discussed on pages 355 and 356 of the fifth edition of "The Making, Shaping and Treating of Steel." The great expansion of the automotive, machine-tool, chemical and oil industries after I9I0 opened up a large market for special steels, whereas the output of steel before that time was mainly for structural purposes. The need for building more blastfurnace capacity complementary to bessemer operations, combined with the availability of the' necessary amounts of steel scrap, both contributed to the extension of open-hearth plants at the -exense of besskmer capacity. The ability of the open-hearth furnaces to consume virtually all types of raw materials as far as phosphorus content is concerned, and the need for selecting low-phosphorus ores of rapidly decreasing sources for the bessemer, also played a part in the reduction of bessemer steelmaking operations and the increase in basic open-hearth plants. As a consequence, the proportion of bessemer steel made, in this country decreased from 65.7 per cent of the total in 1900 to 37.1 per cent in 1910, and only 6.8 per cent of the total in 1937. The metallurgical concepts existent between 1910 and 1920 caused the writing of many specifications of very low phosphorus and sulphur content, which definitely barred bessemer steel from many commodities. Now sulphur is being added to many open-hearth and bessemer steels in amounts far exceeding the maximum sulphur content of good bessemer steel. Re-phosphorizing is also widely practiced for several specific applications. Even today, the chemical-analysis limits of many important steel specifications have an arbitrary and archaic tinge. The old standard "0.30 to 0.60 per cent manganese" might be mentioned in this connection as similar to the rigid requirements for maximum sulphur and phosphorus that were established at least 25 years ago. The literature is full of vague and complee discussions of the effects of nitrogen and oxygen where these elements existed in steel in amounts less than 0.02 per cent. Many failures have been attributed to these elements without reasonable proof on which to base the conclusion. Methods of determining oxygen in steel require such complicated equipment that only a few research laboratories have the required apparatus. Even so, the accuracy of oxygen determinations in steel has been only recently reproducible. Up to the present time, no one has succeeded in obtaining a sample of molten steel that accurately indicates the full oxygen content of the metal in the furnace or ladle because the molten sample

Jan 1, 1944

By William B. Phillips

The concentration of natural magnetites has been carried on in this country for several years, and more or less information has been collected on the subject. Various inventors, availing themselves of the magnetism which is inherent in such ores, have devised machines for separating the impurities from the ore by means of the electric current; and a greater or less degree of success has rewarded their painstaking and persevering efforts. We are now fairly in position to judge of the value of the process as applied to such material. It is not my purpose to speak of this matter further than may be required by the emergencies of the case. I shall assume that most engineers and metallurgical chemists are already acquainted with what has been done at the Chateaugay mines, at Mineville, at the Benson mines, at the Weldon and Ogdensburgh mines, and at Cranberry; although, at this latter place, there has not been so much done as we could wish. I shall not now speak of the various types of separators. From the time of William Fullarton, to whom was granted an English patent, in 1792, for separating iron-ore by the application of magnetic attraction, down to the present time, a great. many devices have been suggested, and a great many patents taken out for this purpose; but it is not necessary now to enter upon a discussion of their merits. Perhaps, at some future meeting of the Institute, after we shall have experimented further with some of the machines on the market, there may be an opportunity to contribute something to the current knowledge of the efficiency and economy of separating-machines. In this paper I propose to give, as briefly as possible, the results already reached in converting a non-magnetic ore into magnetic ore, and then concentrating it over a magnetic separator of the alternate-polarity type. I am aware of the work

Jan 1, 1896

By YANG TSANQ WOO

THE method of making coke that has been adopted at the Kaiping and other collieries in northern China resembles, to some extent, the familiar bee-hive oven process of the United States, except that a kiln with permanent sides is used instead of a closed oven, and the products of combustion are drawn off at the bottom, In building coke-kilns in China, two circular holes, 8 ft. 6 in. in diameter at the bottom and 13 ft. in diameter at the top, are excavated in the ground, both being .connected at the bottom by a flue as shown in Fig. 1. The sides and bottom of the kiln are lined with fire-bricks, and covered with a layer of fire-clay, and a rectangular opening, 6 in. by 8 in., connects the bottom of each kiln with the main flue. Around the edge of the hole, and overlapping the lining, is a wall of fire-brick extending .2 ft. 6 in. above the level of the ground. An open space 5 ft. wide is left in this wall, through which the coal is carried into the kiln and the resultant coke removed. This space, of course, is bricked up during the time that the coking operation is being carried on. The wall is pierced with nine flue-openings uniformly placed around the circumference, each intervening space in the wall being strengthened with a brick buttress, as is shown in Figs. 2 and 4. The floor of the kiln, as well as the main flue, is lined with fire-brick. Before charging the coal, it is first placed in shallow bamboo sieves, 2 ft. in diameter, and immersed in a trough 10 ft. long, and 3 ft. wide, fed with pit-water; in which it is washed by hand. Fig. 3 shows the manner in which the washing is done. From 25 tons of good " dust" coal, 22.5 tons of washed coal are obtained. When ready to charge the coal into the kiln a temporary cone-shaped flue of fire-wood and lump coal is first built to a

Nov 1, 1905

E. E. THUM,* Salt Lake City, Utah (written discussion?).-While the present paper is confined exclusively to the microstructure of fusion welds, it may be of interest to draw attention to certain appearances existing in resistance welds such as spot or butt-welded joints produced by the Thomson process. For instance, a butt weld between two pieces of carbon tool steel (carbon about 0.90 per cent.) will show concentric ellipsoids of the various materials from pearlite to martensite. The surfaces of demarcation are quite well defined, the center of the ellipsoid being at the intersection of the axis of the piece and the plane of the weld. Often these unannealed welds show a troostitic center; evidently this core was not quenched as rapidly as the surrounding shell. Such specimens are beautiful samples for instruction purposes. An annealed butt weld of this kind will show a very well defined central ellipsoid of decarburized, materials. It is interesting to consider the reason why this change takes place. It must be understood that the heat is on the metal for a very short time, possibly 30 sec. It is therefore evident that the decarburization, or migration, of the carbon takes place with extreme rapidity. Since no blowholes are evident in a well-made butt weld, the deoxidizing air and the products of combustion must migrate with the highest speed; second, the carbon might migrate back into the stock; or, last, a large proportion of the pearlite may be extruded with the hot metal, which forms a fin at the plane of weld. Examining these possibilities in detail, it is not probable that such deep-seated decarburization, extending with maximum effect to the very center of a 2-in. round bar, is done by reaction with the oxygen of the air. This would postulate entrance of oxygen and egress of carbon oxides in large quantity without leaving behind traces in the form of oxides or

Jan 5, 1919

By J. L. Rodda, R. L. Wilcox, E. C. Truesdale

In recent years various problems in connection with research work on the preparation and properties of zinc-base alloys have required reliable information concerning the constitution of the zinc-rich portion of the iron-zinc equilibrium diagram. On numerous occasions rather positive indications were obtained that, for example, the solubility of iron in zinc was incorrectly represented on the current equilibrium diagrams. A careful study of all the available literature relating to the iron-zinc system led to the conclusion that much of the early work was unsatisfactory as measured by present standards of experimental accuracy, and as a result it was decided to redetermine the location of the liquidus curve and of adjacent portions of the diagram. Part I of this paper comprises a description of the experimental methods and a summary of the results by means of which the zinc-rich end of- the iron-zinc diagram has been revised in the following ways: 1. Measurements of the solubility of iron in liquid zinc by several different sampling methods, leading to a relocation of the liquidus curve. 2. Microscopic, conductivity, and X-ray studies of the solid solubility of iron in zinc, which, together with thermal analyses, have resulted in new values for the solid solubility and the eutectic temperature and composition. 3. Heating and cooling curves, obtained by a refined differential method, leading to new locations for the two peritectic horizontals. In Part I1 of the paper the attempt is made to review all of the published work having a bearing on the constitution of the iron-zinc system, and to correlate the present results, and some recently published data involving the use of X-ray technique, with the earlier work, much of which was done from 25 to 30 years ago.

Jan 1, 1936

By James F. McConnell, Charles W. Statler

Pennsylvania's existing large coal-fired units are limited to 2.0, 1.8, or 0.6 lb of sulfur per million Btu fired, depending on site location. Multi-stream coal preparation can be employed on system basis to extract the highest quality fraction of coal for use in units requiring the lowest sulfur. The middling fraction can be directed to units permitted higher sulfur. General Public Utilities Corp. has concluded that it is feasible to advance the state-of-the-art of heavy media coal preparation to produce an intensively cleaned primary product of 1.3 sp gr of less than 0.6 lb of sulfur per million Btu for the new unit and a middling product of 2.0 lb of sulfur per million Btu for existing units.

Jan 1, 1977

By R. R. Klimpel Discussion by C. C. Harris, L. G. Austin

C. C. Harris (Columbia University) — The authors ' have presented relationships for the random division of a magnitude into r + l parts taking account of the order of selection. Interpreting their model in comminution terms, their Eqs. 7, 9 and 11 refer to the one-dimensional case; that is, to the subdivision of a long thin rod at random. It is assumed that the fragments may be indefinitely small. Real materials, however, are limited in the degree of subdivision which can be attained through the intervention of practical restrictions. One in fine grinding is the depletion of microflaws as material becomes finer. Another is the

Jan 1, 1969

By J. Q. Ehrgott

INTRODUCTION The U. S. Army Engineer Waterways Experiment Station (WES), under sponsorship of the Defense Atomic Support Agency, has recently developed a unique dynamic high-pressure triaxial testing device (DHT). The device permits acquisition of both axial and lateral deformation data while undisturbed soil and/or rock specimens are subjected to various states of controlled impulsive-type stresses produced by varying both the axial stress and the radial stress rapidly with time. The device is used to develop controlled dynamic pressure pulses within the triaxial chamber fluid on soil or rock test specimens to 3 inches in diameter. Controlled dynamic axial pulse loads are delivered to the specimen by a piston driven by an existing pneumatic ram loader (SECO). The DHT consists of a triaxial cell and a pressure supply and decay system which permits the chamber pressure to be varied with time. Together the DHT and SECO operate in a testing program so as to provide time varying confining pressures and axial loads to test specimens at independently controlled but synchronized programmed rise, hold, and decay times. Rise time is defined as the time from zero load or pressure to peak load or pressure; hold time is the time of constant peak load or pressure; and the decay time is the time from peak load or pressure to zero load or pressure. The maximum dynamic confining pressure attainable is approximately 15,000 psi and the fastest rise and decay times are 3 millisecond (msec) and 20 msec, respectively. This paper presents a description of the DHT, the necessary support equipment, and details of the measurement system. Performance evaluation tests conducted on clay siltstone and a Cretaceous sandstone are presented since the results demonstrate some of the capabilities of the device and show some of its characteristics.

Jan 1, 1971

By C. E. Birchenall, H. M. Schadel

THE purpose of this study was to measure the vapor pressure of silver as the first step in the determination of activities in silver alloys and to test the limitations of the method adopted. In order to work at low pressures, below 2x10-2 mm of mercury, the orifice effusion technique was employed. To shorten the time of collection of silver from the atomic beam, radioactive silver (Ag110) was used as a tracer. The rate of effusion of a monatomic vapor from an "ideal" orifice, where the thickness of the orifice edge is negligible compared with the orifice diameter, can be readily calculated from the kinetic theory of gases, G = vM a p/v2pRT where G is the weight of material effusing from the orifice per unit time; p is the vapor pressure at oven temperature, T; R is the gas constant; M is the molecular weight of the vapor; and a is the orifice area. Consolidating constants and expressing as the weight of material effusing from the orifice in a period of time, t, (5.83)(10-2) (vM) (a) (t) (p)/vT where GT is total weight of monatomic vapor effused (g); M is molecular weight of the effusing tracer vapor; a is orifice area (cm2); t is time of effusion (sec); p is vapor pressure of effusing material (mm of Hg); and T is oven temperature (OK). The vapor effuses from the orifice in a hemispherical pattern, and the intensity of the beam in any direction is given by the cosine distribution law.' Considering this, the weight of effused material can be calculated from the amount of material passing through a circular collimator intersecting the beam. If such a collimator is in a plane parallel to the plane of the orifice and with center on the normal to the orifice center, GT = G?/1-cos2? = G?/sin2? where G? is the weight of effused material passing through the collimator, and 0 is one half the apex angle of the cone defined by the collimator circumference and the orifice center. Reducing eq 3 to the more directly measurable quantities of orifice to collimator distance, d, and collimator diameter, D, the expression becomes,

Jan 1, 1951

By John L. Lamont, Walter Crafts

SECONDARY hardening in tempering has long been recognized as a typical characteristic of steels containing large amounts of carbide-forming alloys. These steels, when quenched and tempered, tend to soften somewhat after tempering at low temperatures, and to reharden at intermediate tempering temperatures before finally softening to low hardness. This behavior in tempering has been studied by many investigators, chiefly with respect to the secondary hardening of high-speed steels. The initial softening has usually been ascribed to decomposition of martensite and growth of iron carbide particles. The secondary hardening has been explained by formation of fresh martensite from residual austenite, formation of very fine alloy carbide particles and by precipitation hardening of metallic compounds in the ferritic matrix. However, factors derived for the calculation of tempered hardness in low-alloy steels1 indicated only a tendency toward retarded softening rather than a discontinuous rehardening. A study was, therefore, made to determine whether fresh martensite from residual austenite and precipitation hardening are essential to rehardening and the degree to which tempered martensite could be rehardened by precipitation of alloy carbides. The mechanism of carbide rehardening was also investigated to determine the nature of the process. The causes of secondary hardening in high-speed steel have received serious consideration for about thirty years. Among the earlier workers Bain and Jeffries2 in 1923 recognized residual austenite as a significant factor, but in addition, emphasized the effect of the formation of alloy carbide particles of "critical" size. They conceived that freshly quenched martensite forms low-alloy iron carbide at low tempering temperatures; with further tempering the iron carbide is then modified by alloying elements that can diffuse most readily at intermediate temperatures (850°F); and that the iron carbides grow in size by coalescence so that the steel tends to lose hardness. At higher tempering temperatures carbide stability rather than alloy availability becomes the controlling influence and in high-speed steel "iron-tungsten carbide is the most stable one and forms to the elimination of the earlier formed carbides. . . . The iron-tungsten carbide particles reach approximately the size for critical dispersion after a short reheat at 1100°F." This concept, the formation of alloy carbide nuclei, redissolving of the iron carbide, and diffusion of carbon to the alloy carbide, was restated for vanadium steel in 1932 by Houdremont, Bennek, and Schrader.3 Subsequent studies have confirmed that iron carbide changes to alloy carbide at 1000 to 1100°F, but the mechanism of the process has received little consideration .

Jan 1, 1948

By E. S. Machlin, C. W. Chen

THIS investigation is concerned with the origin of the intercrystalline voids and cracks formed in metals and alloys subjected to stress at elevated temperature. There have been many suggestions in the recent literature relating to this problem. Greenwood' suggested that the voids may be produced by vacancy condensation. Zener has stated that shear-stress relaxation across grain boundaries could initiate high tensile stresses at the regions blocking grain boundary slip and thereby cause the formation of cracks. Chang and Grant3 have described the formation of cracks at grain boundary triple points and have experimentally verified Zener's mechanism for the grain boundary regions in the vicinity of a triple point. Subsequent to the completion of this investigation, Gifkins4 developed a model which made use of Stroh's5 mechanism of fracturing to produce sub-microscopic fractures that subsequently grow by grain boundary slip. Chen and Machlin,6 in answer to Gifkins, described a model deduced from the present investigation, in which grain boundary slip provides both the stress to fracture at grain boundary jogs and the deformation required to separate fractured jog surfaces. The possibility of gas condensation to form intercrystalline voids and cracks is eliminated as a basic mechanism because such voids and cracks are developed in vacuum melted material containing minute amounts, if any, of gaseous impurities. In a theoretical evaluation of this problem, Machlin7 concluded that void nucleation by vacancy condensation during creep-rupture is improbable but that vacancy condensation on supercritical sized voids to produce growth is probable. This investigation was begun to evaluate the suggested mechanisms for intercrystalline fracture. In particular, in order to correlate vacancy supersaturation ratios produced in creep with those determined by Bal-luffi and Seigle8 as critical for , the nucleation of voids, specimens were obtained from the same heat of brass as used by the latter authors, through the courtesy of Dr. Seigle. The experiments conducted in this investigation fall into the following categories: 1) Brass—observation of voids produced under a variety of conditions, including creep under compression, to evaluate the mechanisms of void nucleation and growth. 2) Bicrystal experiments to check the mechanism of void nucleation deduced in this investigation. 3) Morphology of intercrystalline voids produced in a variety of metals. Each set of experiments will be described and discussed separately. Experimental Techniques A special creep-rupture test rack was constructed which made it possible to apply the stress to the specimen in a controlled atmosphere of inert gas, reducing gas, or vacuum. All the creep-rupture tests on a-brass (30 pct Zn) were conducted in nitrogen under a pressure slightly above atmospheric. Either dead weight loading or constant elongation rate loading could be applied with the load measured by means of a strain gage dynamometer. In order to obtain a coarse-grained crystal structure stable at

Jan 1, 1958

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors' determined the constitution of copper-silicon-manganese alloys containing over 90 per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper .2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 20 c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. Table I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. A few other changes will be noted (No. 138 at 450°C., No. 149 at 550°C., Nos. 153 and 149 at 750°C.). The change from liquid to beta in equilibrium with kappa in No. 139 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. 1 to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the [K = a + ?] change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300° and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 ± 0.03 per cent or 2.42 ± 0.05 per cent were cast in ingots of 3-in, diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 900°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942