Search Documents

By T. Egleston

ALTHOUGH the success of metallurgical operations depends so largely on the possibility of finding proper refractory materials, which enter so prominently into the cost of their operations, it can hardly be said that our knowledge of them is in a very satisfactory condition, or even that we know very much about them, beyond a few facts which have been gathered through their use. Experience, as a general thing, is an excellent master, but the requirements of * This article was written at the suggestion of the Committee of the Institute on Refractory Materials, with a view of calling attention to the anomalies and difficulties of the subject. It was hoped that its discussion would eventually lead to the appointment of a Commission, by the great metallurgical interests of the United States, to investigate the whole subject, since it is believed that a better and cheaper artificial product can be made than any now in use, and that many other important incidental results would be accomplished by such an investigation.

Jan 1, 1876

By Duane N. Goens, Clifford R. Porter

A 91 kg/h (200 lb per hr) pilot plant was constructed according to "Magnex" design. A non-compliance eastern coal which would generate more than 0.85 kg of SO2 per GJ (2.0 lb of SO2 per million Btu) upon burning was brought into compliance less than 0.52 kg of SO2 per GJ (1.2 lb SO2 per million Btu) during continuous operation of the pilot plant. Approximately 85% of the pyritic sulfur was removed while recovering 90% of the Btu of the feed coal. Pilot plant operation is summarized and preliminary economics presented. Present status of the Magnex design program is reviewed.

Jan 1, 1980

By H. G. Sell, G. W. King

An investigation was made of the lensile proper-ties of recrystallized high-purity tungsten and a W-1 pel ThO2 dispersed-phase alloy over the temperature region of 800° to 2400°C. The thoria addition resulted in a modest strengthening effect over the entire temperature region. A decrease in ductility of both materials occurred above 0.5 Tm which was caused by void formation. Current theories of IT has long been recognized that a second phase of hard particles has a strengthening effect on a pure metal. At low or intermediate temperatures (<0.5 Tm), the strengthening effect is thought to arise mainly from the interaction of dislocations with dispersed particles. Above 0.5 Tm, dynamic recovery processes greatly alter the deformation mechanisms from those simply involving glide, and grain bound- strengthening by a dispersed second phase do not adequately explain the tensile results. Melallographic examination suggests that the improved strength of tire alloy results from the effect of thoria on the mierostructure. Stress-dependent thermally activated processes were found to occur high temperatures. aries may act as sources of weakness rather than strength because of grain boundary sliding. Grain boundary sliding at high temperatures has been postulated to be the primary factor giving rise to the formation of voids or cavities at grain boundaries1-3 which in turn cause premature failure and poor ductility.4 Voids, once formed, can grow by the condensation of vacancies from the equilibrium concentration&apos; or from the excess vacancies produced by the deformation.4,5 The high-temperature tensile properties of unalloyed tungsten have previously been investigated by Sikora and Ha116 and also by Taylor and Boone.7 The purpose of the present work was to investigate

Jan 1, 1965

By J. J. Van Nouhuys

THE economics of aerial survey and the technical processes by the aid of which vertical and oblique aerial photographs are turned into line maps showing the most profuse topographical detail such as contours, rivers, roads, plantations, habitations and cultivated lands do not concern us here. They have been ably and exhaustively described in the publications of the British War Office, handbooks on surveying methods and on photogrammetry and in the South African mining, engineering and geological press. Suffice it to mention that for geological interpretation vertical photographs are used on such scales as 1/5000 to 1/10,000, overlapping each other by 55 to 60 per cent in the direction of flight and some 10 to 20 per cent sideways on to the next sequence or strip. Through this duplication in the overlap the stereoscopic examination becomes possible. The standards by which monochrome aerial photographs are interpreted can be grouped under the following headings: 1. Continuity.-The continuity of topographic relief not obtainable on the ground owing to the smallness of man relative to that relief. Here lies the greatest value of aerial survey with relation to geology. An immediate alignment can often be made of drainages running in different directions on each side of a hill; saddles and gorges in the mountainsides; abrupt termination of outcrop or indubitable signs of faulting. Most conclusive evidence is thus often obtained about faults which may be perfectly visible at one place on the ground but cannot elsewhere be identified because of decreased throw. Similarly, dikes can often be followed notwithstanding frequent interruption and disappearance under the soil. Scattered outcrop in scrub-covered or bush-covered country can be compared with field work. The same applies to geological contacts. Once these have been 3stablished at a few points on the ground, the intervening stretches can be drawn in.

Jan 1, 1937

By N. A. Gokcen, John Chipman

D. C. Hilty (Union Carbide and Carbon Research Laboratories, Niagara Falls, N. Y.)—This paper is a very nicely detailed analysis of a difficult problem. I would like to point out that the results that Mr. Crafts and I published a few years ago had no reference to activity, or anything else of a similar nature; our results were strictly empirical. It is quite gratifying that we now have a case where results involving activity coefficients and results derived from direct observations on actual steel melts are practically identical. When two different laboratories, working from two entirely different approaches, come out with results in such good agreement in their major significance, that is an achievement. It is something that was not possible 15 or 20 years ago. There is one question I would like to ask Dr. Chip-man. It has to do with a very minor point of disagreement in these results. When we reported the kink in the Si-O solubility curve I think you may recall that it came at the different temperature levels at about the order of 0.015 to 0.03 pct 0 and 0.03 to 0.07 pct Si—we also pointed out that we had difficulty in obtaining data at that level, although we finally did get some. I note in going through the data for the present paper, that there are no samples in those particular silicon and oxygen ranges. I wonder if that was purely accidental or was there a reason for it. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—Mr. Hilty, do you have any explanation for that discrepancy between Dr. Chipman&apos;s curve and your own Mr. Hilty—Our explanation for it at that time was that for some reason our system probably was not in true equilibrium with SiO, that is, in equilibrium with the silica crucible at that level. We did observe, however, that that was the level at which both the metal and the slag became saturated with SiO,. On the average, in studying inclusion formation in small ingots permitted to solidify normally from the molten state, we observed pure silica inclusions at silicon contents over about 0.05 pct and FeO type inclusions at silicon

Jan 1, 1953

By Grover R. Castle

INTRODUCTION "Project Financing" or "Project Loans" have become increasingly popular in recent years, and commercial banks are being asked to consider more and more of such financing. However, the analysis of this type of loan is quite different from the analysis of a loan to a financially sound corporation based on the company&apos;s balance sheet. For this reason Chemical Bank did a study of project loans in an attempt to be more sophisticated in our approach to them. As part of this study, we examined 29 project financings for which information was available. In this article I shall describe project loans and set forth the guidelines we developed, as an aid to credit officers who might have occasion to analyse this type of financing. DEFINITION OF "PROJECT FINANCING" OR "PROJECT LOAN" The terms "project financing" and "project loan" commonly describe the various methods that banks and institutional lenders use to finance the construction of new projects on a basis whereby payout is anticipated from the revenue stream generated by the project. A project financing often involves a loan to a new entity formed specifically to own the project. The analysis of a project loan proposal is quite different from the analysis of other term-loan proposals since it involves a credit decision based on the review of a projection or forecast rather than of historical earnings and/or it involves the reliance on contractual obligations of third parties. Lenders are asked to assume the added risks associated with project loans because: 1. Project financing may permit a company to obtain additional leverage. It is possible for companies to arrange financing on a project basis that could not be arranged as a direct borrowing. For example, a company may not be permitted to borrow more money directly, due to a limitation in a bond indenture. However, a project financing can sometimes be negotiated on a basis not prohibited by the indenture. 2. Often the sponsors of, or the stockholders in, the project are seeking an off-balance-sheet financing. For example, 11 of the 29 projects in our study were arranged on an off-balance-sheet basis and one showed on the balance sheet as a deferred income item. An off-balance-sheet financing, for the purpose of this article, is a financing which does not show as a direct liability on the balance sheet of the sponsors of or stockholders in a project. 3. Projects are often located in a foreign country. The financing is arranged so that the lenders assume the political risk on the loan because many companies rightly believe that this arrangement affords a degree of insulation from political risk not otherwise obtainable. 4. Many projects are jointly owned by several sponsors. This form of financing lends itself well to a situation where a new entity is formed to own a project and do the borrowing. Project loans can be used to finance a variety of activities including development of iron-ore deposits and associated pelletizing plants; development of coal reserves; construction of pipelines, alumina plants, fertilizer plants and refineries; etc. The specific areas of analysis can be quite different, depending upon the type of project being financed. It is important, therefore, to classify the proposal according to the type of project, and also by the nature of the financing - nonrecourse financing, financing covered by a guarantee of completion and financing supported by an undertaking lasting for the life of the financing. I will discuss each of these types in more detail later, but first, I should like to make some

Jan 1, 1985

By Ira Joralemon

THE Ajo copper district is in the heart of the Arizona desert, near the western boundary of Pima county. Gila Bend, the nearest railroad point, is 43 miles north of the camp, and the little Mexican border town of Sonoita is 30 miles south. Between Gila Bend and Sonoita, Ajo is the only settlement save for one or two small cattle ranches and the uncertain villages of nomadic Papago families. The Little Ajo mountains rise a few hundred feet above wide desert valleys, beyond which are lava mesas. The camp itself lies at an elevation of about 1,900 ft. above sea level, in a little basin on the east side of the range, separated from the open desert by low hills. In the center of the basin the brilliantly iron and copper stained rocks of Copper mountain rise 150 ft. above -the village. Many varieties of cactus and low desert bushes cover the hills, while in the large valleys there are clusters of mesquite paloverde, and ironwood trees which furnish limited amounts of fairly good fuel. A scanty supply of water is obtained from wells in the desert and from prospect pits in the camp. The nearest abundant source of water is the Gila river, 50 miles north of Ajo. (See Fig. 1.) HISTORY OF THE AJO DISTRICT The Ajo, next to Santa Rita, New Mexico, is claimed to have been the first copper district in the Southwest worked by Americans. In the &apos;60&apos;s or even earlier high-grade native copper and cuprite Ore was mined from shallow surface workings and hauled by bull team 400 miles across the desert to San Diego. From there it was carried in sailing ships to Swansea, Wales. Later, the ore was hauled to Yuma, floated down the Colorado river to the Gulf Of California, and shipped to Swansea. Bat-infested old workings and the massive axles of the bull carts are shown to prove the truth of the stories.

Jan 8, 1914

By V. N. Krivobok

THE study and use of low-carbon manganese steels have been curiously neglected in the general history of developments in alloy steels. Hadfield1 made an extensive study of manganese-iron-carbon alloys about 1886, which culminated in the wide application and use of Hadfield austenitic manganese steel. His alloys were nearly all high in carbon, as compared with the steels discussed in this paper, and he found a marked tendency towards brittleness in the alloys of medium and low manganese content, that is, below 7 per cent. manganese. As a result, there has been a widespread prejudice against the use of manganese steels containing between 1.0 to 3.5 per cent. manganese with comparatively low carbon. Steels of this composition have never been studied adequately in comparison with other alloy steels, and have had little use in practice. In a very recent paper by Sir Robert Hadfield2 the following statement appears: ?. . . manganese-iron alloys with little or no carbon do not seem to offer any practical employment; they only become valuable in the presence of quite high percentages of carbon, 0.90 to 1.50 per cent." The results of the present investigation are so contrary to the findings of Hadfield that the writers feel fully justified in presenting the preliminary report incorporated in this paper.

Jan 1, 1927

By Frank W. Osterwald

Violent, spontaneous destruction of coal faces and ribs during, what are commonly called, bumps endangers and at times destroys life and property in mines of the Book Cliffs coalfield, Carbon County, Utah. Because these mines supply much of the coking coal for the West Coast steel industries, mining is necessary, although costs are high and operating conditions are very difficult at times. As operations continue, mining will go to greater depths, and the difficulties will increase. Whether or not mining can be continued successfully depends in part on whether or not incidence of bumps can be controlled successfully. For this reason, the U.S. Geological Survey, at the request of and in cooperation with the U.S. Bureau of Mines, undertook a study of the Sunnyside No. 1 mine to determine what geologic factors were related to the incidence of bumps. This report presents the preliminary results of that study and indicates that some observable geologic features in the mine may be related directly or indirectly to bumps, and that other features may be used to infer stress distribution around workings that will aid in design of roof support measures. Coal is mined in the Sunnyside No. 1 mine from depths as great as 2500 ft by room-and-pillar methods. The surface topography is rugged with many steep cliffs and deep canyons, hence the load on the coal varies greatly within short distances. Much of the Sunnyside coal is under high stress, and while being mined, it shatters continuously&apos; and falls from the face. Continuous shattering (bumping) makes mining easy, but if the shattering is interrupted, greater stress is built up and violent bumps may result when the coal is mined.

Jan 4, 1962

T. L. Joseph (University of Minnesota, Minneapolis, Minn.)—Mr. Killian is to be commended for his inquiry as to why a decrease of 15.3 pct in coke consumption was accompanied by a decrease of only 1.9 pct in the CO/CO, ratio of the top gas. Although I encouraged him in his efforts to find a more significant and meaningful carbon-gas ratio, the method, calculations, and conclusions originated entirely with the author. Whether we agree entirely with the assumptions underlying his corrected ratio, I think we can all agree that a better ratio is needed, and that he deserves credit for recognizing the need and for doing something about it. To be most useful, the CO/CO, ratio for the top gas should reflect the way in which the carbon is gasified in the furnace, particularly the degree of oxidation and the extent of heat release. The effect of CO, from the decomposition of the limestone and the effect of the reaction of CO and water vapor in the upper part of the furnace on the quality of top gas should be isolated from the effect of more basic reactions such as ore reduction and solution loss. The reduction of sufficient iron oxide to produce a ton of pig iron and the accompanying changes in the proportions of the carbon gases can be expressed on a mol basis as follows: 16.5FeA + 16.5CO - 33FeO + 16.5CO, [1] 33FeO + 33.0CO = 33Fe + 33CO. [2] The CO, from eq 1 normally escapes from the furnace because it does not react with coke at the temperature of its release. However, as much as 50 pct of the CO, from eq 2 may react with coke because it is released at temperatures above 1000°C: 16.5CO. + 16.5CO2 = 33CO [3] Thus we see that the gasification of 16.5 mols or about 200 lb of C in solution loss will regenerate as much CO as is required for the last stage of reduction. The pronounced effect of reaction 3 on the final proportions of CO and CO, in the gas stream is obvious. It also follows that reaction 3 materially alters the heat release but it cannot be entirely eliminated in Lake ore practice. A previous study indicates that 100 lb of solution loss may be necessary to maintain the reducing power of the gas. A reduction of 100 lb from the normal level of 200 lb would mean that over 1,-000,000 additional Btu are released in the process. The 100 lb of additional carbon which will be burned at the tuyeres will release 437,000 Btu and the absorption of 583,000 Btu by eq 3 would be prevented. One of the chief objectives of sized ore burdens and more uniform distribution of the gas stream is to minimize solution loss by completing reduction higher in the furnace and in turn to release the maximum amount of heat from the carbon charged. It was odd, indeed, to find that the use of sized ore and sinter in the careful tests reported by Dobscha had changed the CO/CO2 ratio very little. The author has stressed the close correlation between his corrected CO/CO, ratio and production. A correlation of fuel consumption and the CO/CO, might be more logical. Fuel consumption on the prepared ore burden decreased 15.3 pct whereas the corrected CO/CO2 ratio decreased 19.0 pct. Although this agreement between the reduction in fuel and the reduction in corrected CO/CO2 ratio is not as close as the correlation with tonnage, it indicates the corrected ratio is superior to the normal ratio which decreased less than 4 pct. Some adjustment should be made for the reaction: CO + H2O = CO2 + H2 —700Btu [41 because there is evidence to indicate that about one half of the hydrogen is formed in the upper 21 ft of

Jan 1, 1953

G. M. TAYLOR,* Colorado Springs, Co1o.-I do not think the plan outlined in this paper would work at Cripple Creek. Most of our men have had a pretty good education. The Cripple Creek district is a lessee district-I do not think there is one mine operating in Cripple Creek to-day that does not have the leasing system. We have as many men leasing on our property as we have mining and every plan who is working for wages is looking for n lease-everyman has mined for him- self, he has been his on7n boss on n lease, either on our own property or

Jan 1, 1919

By AIME AIME

THE Petroleum Division held a very successful meeting in Los Angeles, Oct. 4 and 5. The meeting was held on the eighth floor of the Chamber of Commerce building, the first day being devoted to technical sessions. Seventy-five members were registered before the opening of the first session. Glenn D. Robertson, vice-chairman of the local section, opened the meeting and introduced Edwin Higgins, managing director of the California Oil and Gas Association, who gave an interesting talk on the recently enacted gas conservation law in California. He explained that the law is an experiment which will be watched with a great deal of interest. The purpose of the law, which went into effect on Sept. 1, is to curb wastage and over-production of gas,

Jan 1, 1929

By B. W. Gandrud

WET-PROCESS coal-washing tables as we know them today have been in use in this country for approximately 25 years. The literature records only a few table installations worthy of note prior to adoption of the present-day differential-motion table. According to Phillips,&apos; six Campbell bumping tables were being operated by the St. Bernard Coal Co., Earlington, Ky., in 1893. As late as 1923, according to Richardson, 72 such tables were in operation in the Rosedale washery of the Cambria Steel Co., at Johnstown, Pa. Bumping tables probably were not used to any considerable extent except in the plant at Earlington, and at two or three plants in Pennsylvania, but they may be considered as forerunners of the present-day coal-washing table. The transition from bumping tables to the type of tables now in use signalized a revolutionary change iii table design. The advantages of the new design over the old were so outstanding as to make its adoption inevitable. BUMPING TABLES Bumping tables, as the name implies, utilized a bumping action for conveying the refuse and discharging it over the refuse end. The tables were hung from rods attached to overhead supporting beams. A shaft and cam arrangement at one end of the table served as ,the actuating mechanism and imparted to the table an endwise, back-and-forth, swinging motion. A bumping block was fixed in the proper position at the shaft end, so that the table would strike against it at the end of each backward swing. The hanger rods or stirrups were so adjusted as to give the table a slight uphill slope toward the refuse end; that is, the end next to the driving mechanism. The feed box was near the upper end of the table and designed to spread the mixture of coal and water over the width of the table. Wash water was added a short distance below the feed box. With the table in motion and coal mixed with water being fed to it through the feed box, a certain amount of stratification took place, depositing heavy refuse at the bottom of the bed in contact with the surface of the table. Constant bumping and a certain amount of

Jan 1, 1943

By W. M. Gray

The determination of the state of stress existing at a point in any solid body requires the determination of the six components of the stress tensor relative to a convenient set of axes. One general method of doing this in rock is to make strain or deformation measurements associated with local relief of stress in a number of boreholes penetrating a limited volume in the vicinity of the point at which the stress is to be determined. The stress is assumed to be constant throughout this volume. Leeman1 has described a number of the instruments that have been developed for making deformation or strain measurements in boreholes. Panek2 has described the application of statistical methods to the determination of the average components of ground stress from sets of measurements made in boreholes by means of deformation meters of the type developed by the U.S. Bureau of Mines. In this paper attention is given initially to the strain cell developed for use on the flattened ends of boreholes by the Council for Scientific and Industrial Research (CSIR) , South Africa. The equations required for evaluating the average components of ground stress from measurements made by means of the CSIR strain cell are derived. These equations are similar in form to those applying to measurements made by the borehole deformation meter developed by the U.S. Bureau of Mines. The results of an investigation of the properties of the equations are described. These results are important in the practical use of both the instruments mentioned above and any instrument based on similar principles.

Jan 1, 1968

By J. F. Poland

Location of Basins and Geologic Features of Occurrence: The major ground-water resources of California occur and are stored in the many large alluvium-filled valleys of the state. The deposits of Quaternary age which hold the ground water commonly are called valley fill. Meinzerl has discussed the characteristic features of this fill and showed that for western United States its distribution is concentrated chiefly in western Utah, Nevada, central Oregon, California, southern Arizona, and central New Mexico (see fig. 1). For California the principal ground-water basins are shown on fig. 2. Except for the Mojave Desert and the "Basin and Range" Valleys (fig. 2, Nos. 23 and 23A), which are not shown individually, the basins outlined on fig. 2 contain all the large reservoirs in valley fill within the state. The Sacramento and San Joaquin Valleys (fig. 2) together comprise the Great Central Valley of California, which has an area of about 18,000 square miles. The Sacramento Valley contains about 5000 square miles of valley lands, approxi- mately equal to the area of Connecticut; the San Joaquin Valley embraces about 13,000 square miles, equivalent to the areas of Massachusetts and Connecticut combined. Both the area and the ground-water use in the Central Valley is far greater than for all the other shaded alluvial basins of fig. 2 added together. Except for the Sacramento Valley, all the major ground-water basins of the state are south of Sacramento. The valley fill in these ground-water basins has been transported by streams and most of it has been laid down in alluvial fans, producing the typical alluvial-fan structure of aquifers radiating as tongues from a prismatic pile of coarse, permeable debris at the canyon mouths; these aquifers are encased down slope by poorly sorted materials consisting of a clayey matrix with imbedded pebbles and boulders, interbedded with flood-plain silt. In the deeper inland structural valleys, the alluvial deposits interfinger at depth in the valley bottoms with horizontally bedded lacustrine sand, silt, and clay. The San Joaquin Valley is a good example. In the coastal valleys exposed to the sea, such as the Los Angeles coastal plain, the alluvial fans pass coastward into lagoonal and thence to shallow marine deposits. In all these basins, the gravel is coarsest and most permeable near the apexes of the fans, but tongues or lenses of clean gravel and sand may extend for many miles down the fan. Thus, these water-bearing structures are in a position to absorb stream flow near the canyon mouths and to transmit it through the buried radiating conduits.

Jan 1, 1951

By J. F. Poland

Location of Basins and Geologic Features of Occurrence: The major ground-water resources of California occur and are stored in the many large alluvium-filled valleys of the state. The deposits of Quaternary age which hold the ground water commonly are called valley fill. Meinzerl has discussed the characteristic features of this fill and showed that for western United States its distribution is concentrated chiefly in western Utah, Nevada, central Oregon, California, southern Arizona, and central New Mexico (see fig. 1). For California the principal ground-water basins are shown on fig. 2. Except for the Mojave Desert and the "Basin and Range" Valleys (fig. 2, Nos. 23 and 23A), which are not shown individually, the basins outlined on fig. 2 contain all the large reservoirs in valley fill within the state. The Sacramento and San Joaquin Valleys (fig. 2) together comprise the Great Central Valley of California, which has an area of about 18,000 square miles. The Sacramento Valley contains about 5000 square miles of valley lands, approxi- mately equal to the area of Connecticut; the San Joaquin Valley embraces about 13,000 square miles, equivalent to the areas of Massachusetts and Connecticut combined. Both the area and the ground-water use in the Central Valley is far greater than for all the other shaded alluvial basins of fig. 2 added together. Except for the Sacramento Valley, all the major ground-water basins of the state are south of Sacramento. The valley fill in these ground-water basins has been transported by streams and most of it has been laid down in alluvial fans, producing the typical alluvial-fan structure of aquifers radiating as tongues from a prismatic pile of coarse, permeable debris at the canyon mouths; these aquifers are encased down slope by poorly sorted materials consisting of a clayey matrix with imbedded pebbles and boulders, interbedded with flood-plain silt. In the deeper inland structural valleys, the alluvial deposits interfinger at depth in the valley bottoms with horizontally bedded lacustrine sand, silt, and clay. The San Joaquin Valley is a good example. In the coastal valleys exposed to the sea, such as the Los Angeles coastal plain, the alluvial fans pass coastward into lagoonal and thence to shallow marine deposits. In all these basins, the gravel is coarsest and most permeable near the apexes of the fans, but tongues or lenses of clean gravel and sand may extend for many miles down the fan. Thus, these water-bearing structures are in a position to absorb stream flow near the canyon mouths and to transmit it through the buried radiating conduits.

Jan 1, 1951

By G. W. Healy, W. D. Forgeng, N. R. Griffing

The liquidus surface of the C-Cr-Fe system to 1900°C has been mapped from carbon solubility and freezing point measurements, metallographic observations, and published data. In the graphite field, the surface drops precipitously to meet a slope descending from the Cr3C2-C join through the mixed carbide fields to a meandering eutectic valley; this flows from the Cr-C to the Fe-C edge. On the low-cavbon side of the valley, the surface rises to the chromium corner. 1 HE purpose of this inquiry was to gain a more complete knowledge of the C-Cr-Fe liquidus surface. This required an extensive study of carbon and chromium-rich alloys which, in the past, have received the least attention. Sanbongi el al.1 measured the solubility of carbon in liquid alloys containing up to 25 wt pct Cr at temperatures of 1460" and 1545°C and found that it increased with chromium content and temperature. Lucas and wentrup2 also made solubility experiments in graphite crucibles, but at higher chromium contents in the range of 38 to 80 pct and at temperatures of 1550" to 1700°C; however, their experiments were relatively few, and the effect of temperature was not consistent. The present investigation included compsitions ranging from 0 to 94 pct Cr and 1.4 to 11.7 pct C at temperatures up to 1800°C. Saturation experiments in graphite crucibles, thermal analyses during freezing, and metallographic and X-ray diffraction studies were employed to obtain desired information which, together with published data from other investigations about the binary edges and the ternary system at lower carbon levels, made possible the construction of a comprehensive C-Cr-Fe liquidus surface. C-CR-FE LIQUIDUS SURFACE The derived ternary liquidus surface is shown in Fig. 1 where the solid curves are liquidus isotherms. The dashed curves and the binary edges are the liquidus field boundaries of the primary crystals, the arrows along these boundaries indicating their direction with decreasing temperature. Each intersection of three internal boundaries is the composition of liquid involved in four-phase isothermal equilibrium with the three primary crystals whose liquidus fields touch there. It may be observed that a total of six four-phase equilibria occur at melt temperatures. The general topography of the liquidus surface consists of a eutectic valley sloping down from the Cr-C edge at 3.2 pct C to the Fe-C edge at 4.25 pct C. The liquidus surface rises in two directions from the valley, one hillside terminating at the Cr-Fe edge while the opposing hillside rises toward the carbon corner out beyond the top edge of Fig. 1. Both hillsides are interrupted by intersections of surfaces or joints representing the liquid colmpositions of various three-phase equilibria. Seven primary crystals occur, namely a(bcc), ?(fcc), graphite, (Fe, Cr)3C capable of dissolving as much as 15 pct Cr, and three different chromium carbides in which iron is partially soluble by substitution for chromium. The composition ranges of the primary l~hases at melt temperatures are shown

Jan 1, 1962

By William Kelly

THE objeet of this paper is to describe the electric equipment at the iron-ore mines of Penn Iron Mining Co., Vulcan, Mich. and of Republic Iron Co., Republic, Mich.; to give the result&apos;s of tests; and to discuss the methods in use from an operating as well as from an efficiency standpoint. Electricity was introduced at the Penn mines for pumping, hoisting, and compressing air in the spring of 1907, upon the completion of a hydro-electric plant built by that company on the Menominee river about 4 miles from the mines. This plant was described in a paper1 presented before the Lake Superior Mining Institute. A paper2 presented at a meeting of the same Institute describes some of the operating features, and the safety devices of the electric hoist at the Curry shaft were briefly described in the Proceedings of the First Co-operative Safety Congress held under the auspices of the Association of Iron and Steel Electrical Engineers at Milwaukee, Wis., Sept. 30 to Oct. 5, 1912.

Jan 2, 1914

By AIME AIME

SCANDINAVIAN countries seem somehow to furnish an amount of talent and leadership far be- yond their population and among them Sweden is possibly at the top. The United States has many eminent citizens born in the latter, country or who are of Swedish descent and the engineers may claim their full share. In fact, the number is so large that a flourishing Swedish-American Engineering Society has been formed, including a number of A. I. M. E. members. Dr. Waldemar Lindgren is more scientist than engineer, though his work in economic geology has contributed directly to the development of many mines, and he is the valued- adviser of a number of our larger companies. Probably he, himself, values most highly the contributions he has been able to make to scientific theories of the occurrence and genesis of ore deposits. His fellow scientists have placed upon these the high mark of approval by electing him to the National Academy of Sciences, and Princeton University in 1916 recognized his position by conferring on him the degree of Doctor of Science.

Jan 1, 1931

By H. M. Day

THE constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy1 in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were con-firmed and supplemented through X-ray analyses by Preston and Stenbeck.3 According to Murphy, at 276° C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower tempera-tures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in the right region.

Jan 1, 1938