Search Documents

By J. M. Neilson

The occurrence of iron ore deposits in the State of Western Australia has been known at least since the 1930's,3 but the true significance of the deposits has only come to light within the past four years. Although they are widely distributed throughout the State, it is now known that more than 90% of the available iron ore reserves are located in the "Hamersley Iron Province". Western Australia may well contain the world's largest known reserves of iron ore. Recent reports place this reserve at 15 billion tons and an even higher figure may appear in the future. LOCATION, CULTURE AND COMMUNICATIONS It is difficult to comprehend the immense size of Western Australia (Fig. 1). The State occupies almost one million sq miles and it is more than 2000 miles from north to south. More specifically, it stretches from the 14th to the 35th parallel of latitude south. The Ophthalmia Region in the Hamersley Iron Province is barely halfway up the long dimension of the State. Nevertheless, the region is 800 miles north of Perth, a distance comparable to that from New York to Chicago or to that from Chicago to New Orleans. The Hamersley Iron Province (so named in 1963 to distinguish it from the Pilbara mineral district adjacent to it on the north) covers an area of approximately 30,000 sq miles in the northwestern part of the State. It extends in a roughly oval form from the Indian Ocean to the Gibson Desert of the interior, a distance of about 300 miles. With the exception of the small coastal towns of Onslow, Roebourne and Port Hedland and a few other communities such as the asbestos-mining town of Wittenoom, the region is very sparsely populated. Sheep and cattle stations are scattered thfough the region and these and the main towns are connected by truck tracks and a few main highways. Voice communication is almost entirely by the short-wave radio net operated by the Royal Flying Doctor

Jan 1, 1965

By St. John, JOHN Ancel

AT THE New York meeting of the Institute of Metals Division in February, 1927, Jeffries and Tarasov presented a paper on Tungsten and Thoria,1 in which the experimental facts were interpreted in accordance with the prevailing point of view that the thorium is present as the oxide, thoria. In discussing that paper the writer of this article stated that his own investigations, which had been unavailable to Messrs. Jeffries and Tarasov, showed that the so-called "thoriated" tungsten filament failed to disclose any sign of the oxide when subjected to X-ray diffraction analysis, but did give plenty of evidence of the presence of metallic thorium and, in certain cases, of a material believed to bean alloy of tungsten in thorium. Since these results were completely at variance with the results reported in the paper under discussion and with other papers which had preceded it from time to time in the past, it was felt that further discussion should be withheld until the new evidence could be presented adequately. Arrangements were therefore made to present that evidence at this meeting. MATERIAL EXAMINED The material examined was high-emission filament such as is used in radio tubes, supposed to contain about 0.75 per cent. thoria. The actual analysis was not stated.

Jan 1, 1927

By Stanley J. LeFond, Neal Davis

Drilling an oil well or most other types of drilling or coring is no longer a simple and uncomplicated operation. Drilling today at depths which exceed 9144 m (30,000 ft) is hazardous and requires personnel with long and varied experience in drilling. It also requires extensive experience and knowledge in the use of materials which are added to the drilling fluid or "mud," more often than not materials utilizing an industrial mineral. The drilling fluid can vary from a simple mixture of water and "mud" to a very sophisticated, scientifically compounded drilling fluid. Industrial Minerals Used in Drilling Fluids Industrial minerals which are commonly used in oilwell drilling and completion are listed in Table 1. The most important minerals, determined by sales, are bentonite and barite. The other minerals listed are either used to achieve a specific purpose or are used regularly but in limited quantities. The main suppliers of drilling fluids internationally are Magcobar Div., Dresser Industries, Inc.; Baroid Div., National Lead Co.; IMC Drilling Mud Co., (a subsidiary of international Minerals and Chemicals Corp. and Halliburton Co.); and Milchem, a division of Baker Industries. Most of the industrial minerals are found in North America, with barite mines and processing plants located in Nevada, Arkansas, Missouri, and Arizona, and bentonite mines near Graybull, WY. Other mines, such as those in Nova Scotia, are capable of shipping to South America and to the European and Middle East countries. Most of the materials processed by any of the suppliers must conform to specifications set by the American Petroleum Institute (API) or the Oil Companies Material Organization (OCMA). These specifications provide for uniform physical and chemical properties of the materials to be sold on the open market. Function of Drilling Fluids In the early days of rotary drilling, the primary function of drilling fluids was to bring the cuttings from the bottom of the hole to the surface. Today it is recognized the drilling fluid has at least ten important functions: 1) To remove the cuttings from the bottom of the hole and carry them to the surface. 2) To cool and lubricate the drill string and drill bit. 3) To build an impermeable cake on the wall of the hole. 4) To control subsurface pressures. 5) To hold cuttings and weight material in suspension when circulation is interrupted. 6) To release sand and cuttings at the surface. 7) To support part of the weight of drill pipe and casing. 8) To reduce to a minimum any adverse effects upon the formation adjacent to the hole. 9) To insure maximum information about the formation penetrated. 10) To transmit hydraulic horsepower to the bit. In order to accomplish some or all of these functions while penetrating formations of various characteristics, several types of drilling fluids systems have been designed. Types of Drilling Muds There are two basic drilling fluid systems-water-base muds and oil-base muds. There is a wide variety of groups within these two main

Jan 1, 1983

By H. W. Morse

THE CHAIRMAN (H. W. MORSE).-Gentlemen, for the first time in the history of the American Institute of Mining Engineers, we have a full session on the subject of leaching-especially on the leaching of copper ores.. This branch of metallurgy is rather in its infancy. We have had one big plant running for a year or more, and pretty successfully; and another one which will be started in February or March, the New Cornelia. We have another one at Garfield for the Utah company, which is just designed and construction begun; and from several other points come reports of interesting test work. The first paper on the program this evening is one of some of the test work on the New Cornelia ore by myself and Mr. H. A. Tobelmann. LAWRENCE ADDICKS, New York, N. Y. (written discussion).-The Ajo proposition has had, as I understand it, two great advantages: it has not been obliged to measure leaching against flotation or some other metallurgical process, and it deals with a copper content high enough

Jan 12, 1916

By L. T. Leyson, U. C. Tainton

Some time ago, at ameeting of the Institute Prof. J. W. Richards1 said, "I take exception to the statement that all the factors in the production of electrolytic zinc were known long ago.... There is possible in my opinion an improvement of perhaps 50 per cent. in the new electrolytic processes." An examination of the literature of the subject will show the justness of Professor Richards' contention. The work of the earlier investigators was carried on in the shadow of difficulties that, today, are hardly more than memories. We seldom hear now of zinc sponge, that bête noir of the electrolytic-zinc pioneers. Zinc sponge was the name given to a peculiar, soft, black, non-adherent form of zinc deposit that was utterly useless for melting into ingot form. At the big plant at Cockle Creek, New South Wales, in 1897, Edgar Ashcroft2 said that the solution in the plant would suddenly, and without ascertainable cause, go' "bad" and begin to deposit spongy zinc. The most delicate, even spectroscopic, methods of analysis were unable to detect any difference between "good" solution and "bad" solution; either form might change to the other on being kept for a while. When it is added that an outbreak of this insidious disease (which appeared to be infectious, or at least contagious) could be dealt with only by discarding the solution and washing out all tanks and pipe lines, some idea may be gathered of the troubles of the zinc electrometallurgist in what may be spoken of as the "sponge age" of electrolytic zinc. Thanks to the efforts of a number of investigators, we are today able to diagnose with considerable certitude the nature of the malady that puzzled Ashcroft and his co-workers. The researches of Mylius and

Jan 1, 1924

SULPHUR is a very well known mineral and apparently is produced in many places. It is engendered from an unctuous earthy and powerfully hot substance so that it is considered among experienced workers to bear a resemblance to the element of fire. This is called by these same men the masculine seed and the prime agent of Nature in the composition of metals. Because of its great dryness and heat it has, as experience shows, affinity with fire, which is easily introduced in it when brought near. And once introduced the fire is quenched only with difficulty before its unctuousness is wholly consumed. Although it shows itself to us of such a hot and dry nature, we must not think that sulphur is a substance so pure that it can stand by itself or that in order to attain its form it has no need of its portion and part of moisture like every other mixture. This is shown to us by its easy fusion, in which it resembles the metals. This thing is found in many places and in many varieties of color; some are white, others yellow and orange, and some others between gray and black. They also say that some red is found. It does not occur in that arrangement of veins like other minerals, but most liberal Nature makes whole mountains of it as is seen in the Aeolian islands, [26] near Sicily, in Etna or Moncibello which is the island of Sicily, at Pozzuoli, in the territory of Rome, in the Sienese domain at San Filippo, and in many other similar places. It is a substance that has a very strong odor and is most unpleasant to smell. It is very fixed in its substance so that it is never corrupted by time, by boiling, or by the moisture of water. For although it may stand in water a long time it never becomes soft nor does it ever decrease or increase in weight. It is brittle and easily crushed very fine. It is said that a trace of garlic rubbed on the mortar helps anyone who wishes to reduce it to impalpability. Its ores have a form more like earth than like stone although they some¬times have the color of a certain soft rock. The places where it is found are easily recognized by the great odor that they give out and by the very hot baths that often spring forth near it. What I have already told you about quicksilver that is contrary to the

Jan 1, 1942

By Dean Goodermote, Carla S. Stone

I Introduction Coal fuels China. Roughly 70 percent of all commercial energy demand is supplied by domestic coal production and with the recent Chinese opening to the West, the Chinese Coal Industry may figure prominently in the export market as well. Because of the importance of China's coal industry to the future of China and the Pacific Rim energy balance, this paper reviews the industry and offers some cautious projections for its outlook. II Energy's Position in the Current Political and Economic Climate Traditionally, Chinese society has been dominated by the policies of its most important government leaders. Deng Xiaoping, Vice Chairman of the Communist Party is the current leader of China. Deng and his proteges are pragmatists. Although China's government structure is based on Marxist/Leninist tradition, Deng and his followers are promoting experiments with market economics and expanded relationships with Western Countries, which have encouraged foreign investment in China. Energy companies represent just one type of industry that is interested in helping the Chinese to develop their abundant natural resources. Although China's leadership is committed to a program of economic modernization, that program currently is experiencing what the Chinese government terms "readjustment". Readjustment cuts back in imports due to deficient foreign exchange and deemphasizes heavy industry, while it encourages agricultural and consumer goods output and, most imporant, energy production. Increased Chinese coal and oil production is essential both to fuel industry and, equally important, to provide foreign exchange. If sufficient energy production is not forthcoming, then economic growth will be severely retarded. China's 1979 per capita GNP of $260 is only slightly better than the weighted average achieved by low income countries of $230. (1) Delays in growth could lead to social unrest, threatening the position of the current leadership. Since there is no institutionalized mechanism for leadership succession and policy continuation, it is reasonable to assume that leadership changes could result in energy policy changes. III Energy Consumption Energy production is important to China's future economic health as highlighted by the World Bank. If China's economy grows rapidly, 5 percent to 6 percent during this decade, the Bank noted, a significant energy shortfall could occur as early as 1985. This state of affairs contrasts sharply with China's current position as a net hydrocarbon exporter. (2) To assure a healthy economic future, China's leadership is attempting to reduce its rate of increase in energy demand through conservation as well as to boost energy output. A massive conservation promotion program has been underway since 1979 and there is much room for improvement. China's industrial sector is only about half as energy efficient as is U.S. industry. (3) During the last two decades, each percent of increase in GNP has been accompanied by a 1.8 percent of increase in energy consumption. (4) This compares rather poorly with the United States where a less than one-to-one relationship exists. IV Energy Supply The short term prospects for oil production are uncertain. Production increases were rapid in the 1960's and early 1970's, averaging 20 percent annually, but most of this increase came from one field, Daquing. Now that Daquing's production has peaked and the offshore potential has yet to be developed, petroleum production has maintained a plateau of 2.1 million b/d, at least temporarily, of which approximately 15 percent is exported. (5) Output

Jan 1, 1982

By E. S. Leaver

THE presence of soluble base metals in precious-metal ores usually precludes cyanidation as the best method of treatment. The laboratory experiments described in this paper show the possibility of cyanidation of gold-silver ores containing less than 0.5 per cent, of cyanide-soluble copper and the effect of zinc in the cyanide solution. PART I.-COPPER IN CYANIDATION The proposed process of cyanidation of precious-metal ores containing copper is based on the regeneration of about 80 per cent., of the cyanide used in the dissolution of the copper. The method of regeneration involves a combination of the sulfide and the acid precipitation of the copper and silver. The resultant solution is made alkaline with lime, and the gold is precipitated with zinc dust. Solubility of Copper Minerals in Cyanide Solution In order to determine the solubility of copper minerals, including metallic copper, under the usual conditions for cyanidation, experiments were conducted with synthetic ores. Each ore sample was prepared by mixing the particular pure copper mineral with barren sea sand. Both the mineral and sand were ground to pass 100 mesh before they were thoroughly mixed. The percentage of copper in each head sample was determined by direct assay, excepting the metallic copper sample, which was computed on weights before mixing. Table 1 gives the results.

Jan 1, 1929

Scraper With over 40 pet more struck capacity than previous models, the new Caterpillar No. 90 scraper is designed to increase earthmoving production when used with D8 tractor power. This scraper moves dirt with the aid of a hard surfaced, reversible cutting edge. Material is carried in a flat, doublebottom bowl of high tensile steel. Operation is by means [ ] of a cable-control unit, which can be mounted on the rear of the tractor to provide for positive loading and ejection. Tapered roller bearings are installed at each axle. The scraper uses two 24.00 to 29 front tires and two 27.00 to 33 rear tires, all four of 24-ply rating. When loaded, the scraper distributes 60 pet of the weight on the rear tires. Circle No. 1

Jan 1, 1952

By O.W. Ellis

Recently there has been a considerable revival of interest in the effects of the various elements commonly added to brass for the purpose of increasing its strength. For many years the work of Guillet2 alone gave reliable information in this regard. Even today his determinations of the coefficients of equivalence of the various elements relative to zinc in brass are those universally employed in industry. This is so because these coefficients have stood the test of time—their substantial correctness has been proved in almost universal practice. It is not our intention to discuss here these coefficients or their use. Rather do we wish to emphasize the need for further systernatic studies of the mechanical properties of the ternary systems of copper, zinc, and other individual elements. Since Guillet published the results of his first investigations Millington, 16 Smalley33 and Thiband 45 have added somewhat to our information. In general they have confirmed the findings of Guillet, which may be stated in the following rather general terms: 1. The addition of aluminum to the 70:30 and 60:40 brasses progressively increases their hardness and strength and reduces their ductility and resistance to shock. 2. The addition of small amounts of iron to a 60:40 brass improves its strength without affecting its ductility. 3. The addition of small amounts of manganese to a 60:40 brass causes a progressive increase in its strength and reduction in its ductility. A considerable amount of information has been amassed in regard to the effect of nickel on brass (9, 22, 41) which it is unnecessary to refer to here, in view of the scope of this paper. The situation in regard to these alloys in 1926 was very clearly stated by an anonymous writer,47 in The Metallurgist of February of that year, whose remarks were so to the point that they are well worth quoting: It will he seen that there are still large fields remaining to be studied in each of these systems (those of the aluminum, iron, nickel and manganese brasses) before our knowledge is adequate. When we come to the more complicated systems the position is even less satisfactory, and on account of the very incomplete nature of the work which has been

Jan 1, 1929

By O. W. Ellis

Recently there has been a considerable revival of interest in the effects of the various elements commonly added to brass for the purpose of increasing its strength. For many years the work of Guillet2 alone gave reliable information in this regard. Even today his determinations of the coefficients of equivalence of the various elements relative to zinc in brass are those universally employed in industry. This is so because these coefficients have stood the test of time—their substantial correctness has been proved in almost universal practice. It is not our intention to discuss here these coefficients or their use. Rather do we wish to emphasize the need for further systernatic studies of the mechanical properties of the ternary systems of copper, zinc, and other individual elements. Since Guillet published the results of his first investigations Millington, 16 Smalley33 and Thiband 45 have added somewhat to our information. In general they have confirmed the findings of Guillet, which may be stated in the following rather general terms: 1. The addition of aluminum to the 70:30 and 60:40 brasses progressively increases their hardness and strength and reduces their ductility and resistance to shock. 2. The addition of small amounts of iron to a 60:40 brass improves its strength without affecting its ductility. 3. The addition of small amounts of manganese to a 60:40 brass causes a progressive increase in its strength and reduction in its ductility. A considerable amount of information has been amassed in regard to the effect of nickel on brass (9, 22, 41) which it is unnecessary to refer to here, in view of the scope of this paper. The situation in regard to these alloys in 1926 was very clearly stated by an anonymous writer,47 in The Metallurgist of February of that year, whose remarks were so to the point that they are well worth quoting: It will he seen that there are still large fields remaining to be studied in each of these systems (those of the aluminum, iron, nickel and manganese brasses) before our knowledge is adequate. When we come to the more complicated systems the position is even less satisfactory, and on account of the very incomplete nature of the work which has been

Jan 1, 1929

By E. C. Wright

THE bessemer process is nearly one hundred years old. William Kelly, the American inventor, was able to demonstrate that he had accomplished the pneumatic purification of molten pig iron as early as 1847; Henry Bessemer's English patent was granted in 1855. The application of this steelmaking process since then and the present position of bessemer steel are concisely discussed on pages 355 and 356 of the fifth. edition of "The . Making, Shaping and Treating of Steel." The great expansion of the automotive, machine-tool, chemical and oil industries after 1910 opened up a large market for special steels, whereas the output of steel before that time was mainly for structural purposes. The need for building more blast-furnace capacity complementary to bessemer operations, combined with the availability of the necessary amounts of steel scrap, both contributed to the extension of open-hearth plants at the expense of bessemer capacity. The ability of the open-hearth furnaces to consume virtually all types of raw materials as far as phosphorus content is concerned, and the need for selecting low-phosphorus ores of rapidly decreasing sources for the bessemer, also played a part in the reduction of bessemer steelmaking operations and the increase in basic open-hearth plants. As a consequence, the proportion of bessemer steel made in this country decreased from 65.7 per cent of the total in 1900 to 37.1 per cent in 1910, and only 6.8 per cent of the total in 1937. The metallurgical concepts existent between 1910 and 1920 caused the writing of many specifications of very low phosphorus and sulphur content, which definitely barred bessemer steel from many commodities. Now sulphur is being added to many open-hearth and bessemer steels in amounts far exceeding the maximum sulphur content of good bessemer steel. Rephosphorizing is also widely practiced for several specific applications. Even today, the chemical-analysis limits of many important steel specifications have an arbitrary and archaic tinge. The old standard "0.30 .to 0.60 per cent manganese" might be mentioned in this connection as similar to the rigid requirements for maximum sulphur and phosphorus that were established at least 25 years ago. The literature is full of vague and complex discussions of the effects of nitrogen and oxygen where these elements existed in steel in amounts less than 0.02 per cent. Many failures have been attributed to these elements without reasonable proof on which to base the conclusion. Methods of determining oxygen in steel require such complicated equipment that only a few research laboratories have the required apparatus. Even so, the accuracy of oxygen determinations in steel has been only recently reproducible. Up to the present time, no one has succeeded in obtaining a sample of molten steel that accurately indicates the full. oxygen content of the metal in the furnace or ladle because the molten sample

Jan 1, 1944

By Aureal T. Cross

THIS paper is a review of the published literature on research in coal geology, principally exclusive of resource studies, which appeared or became available during 1950 and the latter part of 1949. This report is not to be construed as being complete. The papers referred to in the bibliography are those among many more, which were read either in full or in abstract. Undoubtedly other papers were published which either escaped the author's notice or were not available to him. Those which were seen in abstract only (about one fourth of those listed) were not available in time for the inclusion of more than a notice. An outline of all papers listed in the bibliography has been arranged by subjects and reasonable subdivisions with some papers cited under more than one subject. Most papers are indexed according to the principal subject of discussion or research only as to an unusual or noteworthy section of the entire report. There will likely be some disagreement as to the quality or merit of some of the papers selected and the specialist may be supercritical of the outline or organization of papers in his field. It may be that attention has occasionally been drawn to papers reporting old information or conclusions of questionable value. Conferences and Meetings One of the best indications of the growing interest in coal geology problems in the United States is the increasing number of times this field has been the focus of attention at conferences and meetings. Notable among these are the joint meeting of the Society of Economic Geologists and the Geological Society of America at El Paso, November 1949, at which the principal thesis was concerned with low rank carbonaceous fuel deposits, especially of western United States. Among the papers given which are already available were those presented by Barghoorn,'" Parry? Roe? and Parks."' At the annual meeting of the Botanical Society of America in New York, December 1949, a joint meeting of the Paleobotanical and Microbiological Sections was held for which a symposium on Microbiology in Relation to the Geologic Accumulation of Organic Complexes was organized. Publication of the six papers presented by Ralph G. H. Siu, Elso S. Barghoorn, Irving Breger, Claude E. ZoBell, James M. Schopf, and A. C. Thayson is anticipated. At the regular meetings of the Paleobotanical Section at the same time, several other papers of interest reported on coal ball studies, partial coalification of petrified wood, and floras. In Chicago, April 1950, a symposium on Applied Paleobotany was held by the Society of Economic Paleontologists and Mineralogists in conjunction with the American Association of Petroleum Geologists. The five papers presented at this meeting dealt with the use of Paleozoic plant microfossils for stratigraphic work, J. M. Schopf, Devonian-Missis-sippian fossils of the black shales, Aureal T. Cross, Mesozoic plants of stratigraphic value, Th. Just, plant microfossils of the Tertiary, L. R. Wilson, and studies of the Brandon lignite, Elso S. Barghoorn. Early publication of these in the Journal of Paleontology is expected. The Nova Scotia Research Foundation and the Nova Scotia Dept. of Mines sponsored an excellent 3-day conference in June 1950, which dealt with several aspects of coal geology. Papers on coal classification, P. A. Hacquenbard, structure and sedimentation problems in Nova Scotia, T. B. Haites, new techniques of thermal analysis, W. L. White-head, geochemical investigations of Nova Scotia coals, Irving Breger, the role of fossil plant spores in coal correlation and the stratigraphy of the coal-bearing strata of the Appalachian Region, Aureal T. Cross, were given. Some discussions of these papers by those in attendance were recorded, and the entire proceedings is being prepared for publication. In September 1950, an unusual 3-day field conference was held by the Ohio and West Virginia Geological Surveys under the sponsorship of the Coal Geology Committee. This study of the stratigraphy, sedimentation, and nomenclature of the Upper Pennsylvanian and Permian coal-bearing strata of southeastern Ohio, southwestern Pennsylvania, and northern West Virginia was augmented by two discussions on associated rocks (clays and shales) and stratigraphic nomenclature at Wheeling and Morgantown, West Va. An extensive guidebook was prepared, and transcriptions of the Morgantown meeting were made. As a follow-up of the September field conference, a round-table discussion was held on this general topic at a special open meeting of the Coal Research Committee in conjunction with the November meeting of the Geological Society in Washington. Short prepared statements to invite discussion were given on each of several topics by L. M. Cline, Carl 0.

Jan 1, 1953

By Aureal T. Cross

THIS paper is a review of the published literature on research in coal geology, principally exclusive of resource studies, which appeared or became available during 1950 and the latter part of 1949. This report is not to be construed as being complete. The papers referred to in the bibliography are those among many more, which were read either in full or in abstract. Undoubtedly other papers were published which either escaped the author's notice or were not available to him. Those which were seen in abstract only (about one fourth of those listed) were not available in time for the inclusion of more than a notice. An outline of all papers listed in the bibliography has been arranged by subjects and reasonable subdivisions with some papers cited under more than one subject. Most papers are indexed according to the principal subject of discussion or research only as to an unusual or noteworthy section of the entire report. There will likely be some disagreement as to the quality or merit of some of the papers selected and the specialist may be supercritical of the outline or organization of papers in his field. It may be that attention has occasionally been drawn to papers reporting old information or conclusions of questionable value. Conferences and Meetings One of the best indications of the growing interest in coal geology problems in the United States is the increasing number of times this field has been the focus of attention at conferences and meetings. Notable among these are the joint meeting of the Society of Economic Geologists and the Geological Society of America at El Paso, November 1949, at which the principal thesis was concerned with low rank carbonaceous fuel deposits, especially of western United States. Among the papers given which are already available were those presented by Barghoorn,'" Parry? Roe? and Parks."' At the annual meeting of the Botanical Society of America in New York, December 1949, a joint meeting of the Paleobotanical and Microbiological Sections was held for which a symposium on Microbiology in Relation to the Geologic Accumulation of Organic Complexes was organized. Publication of the six papers presented by Ralph G. H. Siu, Elso S. Barghoorn, Irving Breger, Claude E. ZoBell, James M. Schopf, and A. C. Thayson is anticipated. At the regular meetings of the Paleobotanical Section at the same time, several other papers of interest reported on coal ball studies, partial coalification of petrified wood, and floras. In Chicago, April 1950, a symposium on Applied Paleobotany was held by the Society of Economic Paleontologists and Mineralogists in conjunction with the American Association of Petroleum Geologists. The five papers presented at this meeting dealt with the use of Paleozoic plant microfossils for stratigraphic work, J. M. Schopf, Devonian-Missis-sippian fossils of the black shales, Aureal T. Cross, Mesozoic plants of stratigraphic value, Th. Just, plant microfossils of the Tertiary, L. R. Wilson, and studies of the Brandon lignite, Elso S. Barghoorn. Early publication of these in the Journal of Paleontology is expected. The Nova Scotia Research Foundation and the Nova Scotia Dept. of Mines sponsored an excellent 3-day conference in June 1950, which dealt with several aspects of coal geology. Papers on coal classification, P. A. Hacquenbard, structure and sedimentation problems in Nova Scotia, T. B. Haites, new techniques of thermal analysis, W. L. White-head, geochemical investigations of Nova Scotia coals, Irving Breger, the role of fossil plant spores in coal correlation and the stratigraphy of the coal-bearing strata of the Appalachian Region, Aureal T. Cross, were given. Some discussions of these papers by those in attendance were recorded, and the entire proceedings is being prepared for publication. In September 1950, an unusual 3-day field conference was held by the Ohio and West Virginia Geological Surveys under the sponsorship of the Coal Geology Committee. This study of the stratigraphy, sedimentation, and nomenclature of the Upper Pennsylvanian and Permian coal-bearing strata of southeastern Ohio, southwestern Pennsylvania, and northern West Virginia was augmented by two discussions on associated rocks (clays and shales) and stratigraphic nomenclature at Wheeling and Morgantown, West Va. An extensive guidebook was prepared, and transcriptions of the Morgantown meeting were made. As a follow-up of the September field conference, a round-table discussion was held on this general topic at a special open meeting of the Coal Research Committee in conjunction with the November meeting of the Geological Society in Washington. Short prepared statements to invite discussion were given on each of several topics by L. M. Cline, Carl 0.

Jan 1, 1953

By Dan G. Cojocariu, E. Ene-Danalache, I. Huber-Panu

A general model which represents not only batch but also continuous flotation in multi-cell machines is presented. This model considers both the size distribution and the distribution of flotabilities in a size class for valuable mineral particles in the pulp. The general expression is shown to reduce to several previously reported models. In addition, a number of new models are found to arise for different specific assumptions concerning the flotability distribution and/or the size distribution of the particles undergoing flotation. Several of these new models are tested experimentally using laboratory-scale batch and pilot-scale continuous data. Model parameters are estimated from this data and a comparison of calculated recoveries and those experimentally determined are presented. Finally, the influence of the feed rate, aeration rate and valuable mineral content of the feed on the recovery is examined.

Jan 1, 1976

By George H. C. Norman

A NUMBER of methods have been developed for the determination of the dust concentration in air, some of which have been reported as very efficient and for research may be more satisfactory than the method about to be described. In practical mine use, however, the accurate research equipment is unwieldy and requires a high degree of technical skill to manipulate it. Also, it gives less general practical information to the operator in the same length of time than the method described here. Moreover, it is doubtful whether at the present stage of affairs the results obtained from the precise methods have any more practical significance than those obtained with simpler and more portable apparatus, which can rapidly give a sufficiently reliable indication of the relative dust hazard. HISTORY OF DUST DETERMINATION IN ONTARIO The first record of mine-dust determination in Ontario is given in an article by Dr. J. H. Elliott,' in which he records a few dust counts made with the Palmer spray apparatus. There were insufficient data from which to draw any definite conclusions or reasonably compare with present-day counts using the konimeter. The first konimeter dust sampling was started in the Porcupine district in 1926, using light-field counting without adhesive and with no sample treatment before counting. A method of semidark-field counting was used from about 1928 to 1931 and dark-field illumination was adopted permanently about December 1931. The konimeter has been continued as the principal means of dust sampling in the mines of Ontario, where South African practice has been adopted because in South Africa most careful study has been given the problem of silicosis, and very complete records of work done there are

Jan 1, 1937

By H. E. McKinstry

MOVEMENT on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence, coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system. INTRODUCTION IT has long been recognized that movement on a curved or irregular fault surface is capable of separating the walls in certain portions of the fault, but until very recent years the importance of this mechanism as a factor in localizing ore shoots has escaped proper recognition. A short time ago W. H. Newhouse' presented a careful analytical study of displacements and their corresponding open spaces. For reasons that will be discussed later, it frequently happens that portions of the vein which are favorably oriented are not merely wider but also richer than the average. In many cases the widening with its accompanying richness coincides with very minor changes in the dip or strike of the vein, irregularities that commonly escape notice unless the vein is mapped in detail and a careful geometrical analysis made. While the relationship between the width of the vein and the changes in dip or strike has been recognized as a matter of observation, the irregularities have been accepted as more or less the result of accident. There has been very little effort except in isolated cases to find out the causes of these changes in dip or strike. Yet it is clear that if the causes can be recognized and expressed in terms of geologic structure the geologist will know where to look for repetitions of these favorable conditions either on extensions of the same vein or on adjoining veins. Any lack of understanding of the causes is due to the limitations of our ability to interpret our observations and not to the sheer capriciousness of

Jan 1, 1941

By George Smith

THE Secretary of the Interior in his recent report to the President has defined the new public-land policy, which is in fact "but a new application of an old policy." His words may be more acceptable on this subject of land classification than the repetition of phrases which have served some of us for several years. Secretary Lane says of the past: "Congress has always been most generous as to the disposition of the national lands. . . . There was land for all, and it was the government's glad function to distribute it and let those profit who could. . . . And this generous donor was not so petty as to discriminate between kinds of lands, the uses to which they could be put, or the purposes which those might have who got them. Land is land, save when it contains minerals; this was roughly the broad principle adopted. To classify was a task too difficult or not worth while. The lands would classify themselves when they arrived in individual ownership. And so the door was opened for monopoly and for fraud. Of the reaction and the evolution of a new policy, the Secretary continues: "A reaction was inevitable. If lands were to be withdrawn from public service, why might not the government do the withdrawing itself? The old philosophy that `land is land' was evidently unfitted to a country where land is sometimes timber and sometimes coal; indeed, where land may mean water-water for tens of thousands of needy neighboring acres. For the lands of the West differ as men do, in character and condition and degree of usefulness. We had not recognized this fact when we said `land is land.' Lands fitted for dry farming and lands that must forever lie unused without irrigation; lands that are worthless save for their timber; lands that are rich in grasses and lands that. are poor in grasses; lands underlain with the non-precious minerals essential to industry or agriculture; lands that are invaluable for reservoir or dam sites these varieties may be multiplied, and each new variety emphasizes the fact that each kind of land has its own future and affords its own opportunity for contributing to the nation's wealth.

Jan 6, 1914

By W. Spencer Hutchinson

The experiments described in this paper were undertaken primarily for the purpose of measuring the quality of work done in screening and sorting in American concentrating-mills for Prof. Richards' work on Ore-Dressiag. For this purpose a series of samples of screened and sorted products was obtained from four different mills, and a plan was devised for sizing these products, and for tabular and graphic representation of the results. The results, together with discussions as to their significance, so far as they serve to interpret the quality of mill-work, have already been published in the above-mentioned work, and it is not the purpose of this paper to duplicate the work, except so far as is necessary to explain and illustrate methods and appliances. The sizing of coarse products was clone by sifting on screens of sheet-metal with round punched holes. These holes ranged in size from 64 mm. to 0.5 mm. in diameter. Below the smaller limit, punched metal, suitable for this work, was not obtainable, and the sizing was carried on by sifting on woven wire-sieves. The finest woven wire-cloth obtainable gave a hole 0.073 mm. square, and the finest silk bolting-cloth pave a pentagonal hole with an average diameter of 0.069 mm. Even these very fine screens served no useful purpose in sifting certain of the very fine classifier-products, of which all, or nearly all, passed through the finest screen. A new adaptation of a method of settling and decantation with water in beakers was therefore worked out, and by this means the sizing mas carried down to grains of a diameter as small as 0.012 mm. Description of Apparatus and Manipu1ntion.—Sieves of sheet-metal with round punched holes were used as far as practicable, chiefly because, as already explained, the primary object of the experiments was to test mill-work, and the mills had all used

Jan 1, 1905

By Wilbur T. Stuart

TO assist the mining industry in attacking problems of water control, the U. S. Geological Survey has begun a program of research in mining hydrology. In certain fundamental respects water control is similar to development of water supplies from wells or to the drainage of agricultural lands, as many of the tools developed in recent years for quantitative ground-water problems are applicable, with modification, to mine-water problems. In 1952 a 30-day pumping test conducted jointly by the Eureka Corp. Ltd. and the Defense Minerals Exploration Agency provided an opportunity to gain knowledge concerning water movements around a flooded mine shaft. The methods of analyzing the data may be used as a guide for the evaluation of similar problems elsewhere. The Fad shaft of the Eureka Corp. is on Ruby Hill, 1 1/2 miles west of Eureka, Nev. The shaft was completed at a depth of 2465 ft in November 1947 at a site adjacent to the downfaulted block in which the ore was found. As the drift on the 2250 level progressed toward the ore zone, a large flow of water was encountered after the Martin fault was intersected. This flow exceeded the installed pump capacity, and an unsuccessful attempt to recover the shaft and the 2250 level was made in 1948.1, 2 Geology and Hydrology: The complex structure of Ruby Hill is that of an anticline broken first by thrust faulting and later by normal faults. The present orebody comprises several mineralized zones within a block of the Eldorado limestone of middle Cambrian age which was downfaulted 1400 to 1600 ft, and it may be related to a similar body mined at a higher level south of the Ruby Hill fault. At the depth of the largest zone of ore the block is roughly rectangular in shape, about 1000 ft wide and 1500 ft long, and dips about 30" NE, see Fig. 1. It is apparently bounded on the south by the Ruby Hill fault, on the east by the Jackson fault, on the north by the Martin fault, and the west by the Bowman fault. Within the block, but between the Ruby Hill and the Martin faults, are the Office and Adams Hills faults; west of the block and the Bowman fault are the Albion and Spring Valley faults. There are many conflicting reports concerning the water-yielding characteristics of the Eldorado limestone and the condition of the fault zones, that is, whether they are open or tight. However, the diamond-drill records indicate that open spaces as much as 2 or 3 ft across were encountered, and considerable cementing and lining of holes was necessary to maintain circulation of drilling fluid. There is also evidence that the Eldorado limestone was cavernous where it was mined in the early days south of the Ruby Hill fault. At the site of the Fad shaft the formations encountered from the surface down included the Pogonip limestone, Dunderberg shale, Hamburg limestone, and Secret Canyon shale. These formations did not yield large quantities of water to the shaft. The Pogonip limestone, which appears to be permeable and might yield water elsewhere, is above the water table in the vicinity of the shaft. The Secret Canyon shale, immediately overlying the Eldorado in some places but in most places separated from it by the Geddes limestone,3 is apparently tight and does not transmit water. During the 30-day test period the shale briefly confined the water in the underlying formations so that artesian conditions were observed in drillholes E and F, which are cased into the Eldorado limestone, whereas unconfined conditions were observed in drillholes B, C, and D, which were open to the shale. The Geddes limestone, which normally lies between the Secret Canyon shale and the Eldorado limestone, was not encountered in the Fad shaft. The Geddes, a flaggy, fractured limestone, is reported capable of yielding large volumes of water. Water stored in the interstices of this thin-bedded limestone within the Ruby Hill fault zone on the 1200 level of the Locan shaft drowned the pumps in 1923 when the Richmond-Eureka Mining Co. attempted to explore the area along the fault. Eldorado limestone was not encountered in the Fad shaft. In the ore-block area the Eldorado limestone was not entirely offset from other water-yielding formations by movement along the Bowman fault; therefore it may be hydraulically connected with the other formations. Adjacent to the Ruby Hill, Jackson, and Martin faults, the Eldorado lies in contact with other possible water-yielding formations. One of these, the Prospect Mountain quartzite, is separated from the Eldorado by thin, sheared, and broken beds of the Geddes within the Ruby Hill fault zone. A limited examination by the author of the Prospect Mountain quartzite in the Richmond mine at a higher level and south of the Ruby Hill fault indicates that the quartzite is poorly permeable. The monzonite mass south of the quartzite would be a further barrier to the flow of water. The poor permeability of this area is substantiated by records of levels at which water was encountered south of the Ruby Hill fault. In view of the normally low rate of ground-water recharge, if this desert area had been permeable, water levels could not have been maintained at altitudes of many hundred feet above the present water table west and north of Ruby Hill. Thus the ore-bearing block of Eldorado limestone is in contact with possible water-yielding rocks on at least two sides, and if the fault zones are possible conduits for water circulation the geologic and hydrologic conditions are suitable for the infinite-aquifer type of analysis as used and modified here. History of Pumping: During sinking of the Fad shaft a maximum pumping rate of 1500 gpm kept the shaft dewatered sufficiently, but in March 1948, after the 2250 level drift passed through the Martin fault into the Eldorado limestone, the pumps and shaft were flooded. Subsequently additional pump-

Jan 1, 1956