Search Documents

By Arthur Green

A GROUP of 13 cities situated in Los Angeles and Orange counties in Southern California is engaged in constructing an aqueduct to carry water from the Colorado River at a point near Parker, Arizona, to a distribution point sear Riverside, California. The aqueduct will have a total length of approximately 241 miles, and is designed to deliver 1605 cu. ft. of water per second, or a little more than one billion gallons per day. The aqueduct crosses a barren, desert waste and the project includes approximately 91 miles of 16-ft. tunnel. The large amount of tunnel driving that has been done in this country in the past few years has resulted in some remarkable developments in equipment and methods. The building of the Colorado River Aqueduct, with its 91 miles of tunnels, has called on the best engineering knowledge in the country. New and better equipment has been designed for all phases of the work, and this equipment has been coordinated and adapted to the various conditions with a high degree of efficiency. The result has been that records for tunnel driving have been set under adverse natural conditions that exceed the estimates for progress under good conditions. All of the tunnels in the main aqueduct, except the Valverde and Bernasconi at the western end, have a finished diameter, inside the concrete lining, of 16 ft. Fig. 4 shows a section of the tunnel with the concrete lining in place. Fig. 5 illustrates the finished tunnel in three typical sections. The standard tunnel grade is 3.432 ft. per mile in the 16-ft. tunnels, but the Valverde and Bernasconi tunnels have a steeper grade and a finished diameter of 15 ft. 3 in. The rough bore of the large main aqueduct tunnels averages 12.95 solid cubic yards of material per foot of advance in timbered sections and 10.76 solid cubic yards per foot in unsupported sections.

Jan 1, 1936

By A. M. Gaudin, A. F. Taggart

Flotation of ores is a practical utilization of the energy that resides in the surfaces of solids and liquids. The best known manifestation of this energy is called surface tension; an equally important, though less apparent, phenomenon is adsorption. This paper reviews some of the recent investigations of these phenomena, and gives the results of certain experiments performed by the authors. Surface tension is a manifestation of energy having its seat at the bounding surface between the adjacent phases of a multiphase system. Thus, at the interface between a liquid and a gas, or between two immiscible liquids, or between a solid and a gas or a liquid, there are forces capable of doing work, their magnitude depending on the nature of the adjacent phases and the extent of the bounding area. These surface forces are inappreciable when the ratio of surface to volume of the adjacent phases is small, but they become powerful when this ratio becomes large, as it does when one of the phases is highly dispersed. Froth flotation, which consists in buoying solids heavier than water to the surface of water by means of gas bubbles, utilizes the force of surface tension to attach the solid particles to the gas bubbles and again to maintain the floating mass of bubbles as a more or less persistent froth at the surface of a pulp for a sufficiently long time to allow its removal. It follows from the second law of thermodynamics that the potential energy of a system in equilibrium is a minimum. Therefore a multiphase system, tending toward equilibrium, will arrange itself in such a way that the total energy of the interfaces will be the least possible. This end can be accomplished in two ways: by a change in shape that will reduce the interfacial area; by a change in the nature of the surface layer in

Jan 1, 1923

By A. F. Taggart, A. M. Gaudin

Flotation of ores is a practical utilization of the energy that resides in the surfaces of solids and liquids. The best known manifestation of this energy is called surface tension; an equally important, though less apparent, phenomenon is adsorption. This paper reviews some of the recent investigations of these phenomena, and gives the results of certain experiments performed by the authors. Surface tension is a manifestation of energy having its seat at the bounding surface between the adjacent phases of a multiphase system. Thus, at the interface between a liquid and a gas, or between two immiscible liquids, or between a solid and a gas or a liquid, there are forces capable of doing work, their magnitude depending on the nature of the adjacent phases and the extent of the bounding area. These surface forces are inappreciable when the ratio of surface to volume of the adjacent phases is small, but they become powerful when this ratio becomes large, as it does when one of the phases is highly dispersed. Froth flotation, which consists in buoying solids heavier than water to the surface of water by means of gas bubbles, utilizes the force of surface tension to attach the solid particles to the gas bubbles and again to maintain the floating mass of bubbles as a more or less persistent froth at the surface of a pulp for a sufficiently long time to allow its removal. It follows from the second law of thermodynamics that the potential energy of a system in equilibrium is a minimum. Therefore a multiphase system, tending toward equilibrium, will arrange itself in such a way that the total energy of the interfaces will be the least possible. This end can be accomplished in two ways: by a change in shape that will reduce the interfacial area; by a change in the nature of the surface layer in

Jan 1, 1923

By Jo. E. Sheridan

The Dawson coal-mines are owned aid operated by the Stag Canon Fuel Co., of which Dr. James Douglas is President and E. L. Carpenter general manager. The property is situated in Colfax county, N. M., and the openings now in operation are in townships 28 and 29 N R. 20 E., and township 28 N E. 21 E., shown in Fig. I. The mines are part of the southern end of the Raton coal-field, which extends north into Colorado and embraces many coal-camps of the Trinidad section. II. Geology. Geologically, the coal-measures, commonly known as the Laramie series of the Cretaceous system, have x thickness of about 800 ft. in the vicinity of Damson. The coal makes an excellent coke, and, according to some authorities, its coking properties are due to the action of intruded sheets and sills of igneous rock, the sheets occasionally thickening into masses resembling laccoliths, at such places making nearer approach to the coal and sometimes producing small areas of natural coke. There are but few dikes throughout the entire southern portion of the field and little or no faulting along the dikes. In some parts of this great coal-field the intrusive sheets are far removed in the green shales below the coal-measures, and are so much altered as to be difficult of identification. There is but little disturbance of the strata throughout the Raton coal-field in as far as it extends into New Mexico. There are two workable seams in the coal-measures, and two or three smaller coal-seams, ranging from 1 to 2.5 ft. in thick-

Jan 1, 1910

By Robert E. Palmer

The Hawkesworth detachable drill steel shank and bit were invented by A. L. Hawkesworth, while he was a mechanical foreman for the Anaconda Copper Mining Co., at Butte, Mont. Mr. Hawkesworth died on June 16, 1925, at the time that his invention was practically a proved success. The first application for patents was made by him in November, 1918, and the bit is now being manufactured under patents issued in 1922 and 1923. The credit for its development in the early stages belongs to A. L. Hawkesworth, Roy S. Alley, Harry A. Gallwey, E. J. Bowman and various officials of the Anaconda Copper Mining Co. Later improvements, manufacturing problems and the direct usage in the mines were originated and perfected by the mechanical department under C. D. Woodward, E. R. Borcherdt, head of the Rock Drill Equipment Department, Robert E. Kelly of the Mechanical Department, and various operating department heads of the Anaconda Copper Mining Co. The author wishes to acknowledge the assistance of these officials in the preparation of this paper. Comparison of Costs Using Regular Drill Steel and Detachable Drill Steel In 1922 production was satisfactory and sufficient enough to warrant a complete installation in an operating mine. The study and tests were made at the Badger State mine, the production of which averaged 1200 tons of ore per day. E. R. Borcherdt, head of the rock drill equipment department, was in direct charge of the trials, installation, operating problems and records during the entire .period, arid still continues in that position. This mine is a typical Butte mine, operated through a standard four-compartment shaft, served by a double drum hoist and an auxiliary hoist. The texture of the ground and ore has all the variations from soft to very hard granite and sulfide ore with production from levels between the

Jan 1, 1930

By M. E. Wadsworth, A. S. Peck

Infrared spectra disclose that oleic acid will not adsorb on the surface of pure beryl unless the mineral is first activated with HF. The adsorption of oleic acid on HF activated beryl is attributed to the hydrogen bonding of oleic acid monomers to F-surface bridging sites. These sites are formed as a result of the reaction of HF with chemisorbed water or surface hydroxyl. Characteristic infrared spectra of physically adsorbed oleic acid are correlated with flotation at different pH at temperatures of 25°C and 75°C for colloidal and -60-mesh particles. The usual mode of occurrence of the beryllium mineral beryl, Be3A12Si6O18, is in granite pegmatites as pale green, white, or yellow crystals. A dark green gem variety, emerald, may be found in the wall rock of pegmatite veins or in mica schist. The most important beryl deposits in the United States are in the Black Hills District of South Dakota, and several mountain ranges of central and west-central Utah contain potential commercial sources of this mineral. Several papers have been published concerning the flotation of beryl with different conditioning reagents. Kennedy and O'Meara1 reported on the essential use of HF in the flotation of beryl from different ores. The use of calcium hypochlorite to separate HF activated beryl from feldspar after flotation with an amine collector was made by Runke.2 A report on the activation of beryl with different cations using sodium oleate collector was presented by Viswa-nathan and co-workers.3 Flotation of beryl with sulfonate collector and different activating salts was employed by Fuerstenau and Bhappu.4 The role of the surface charge or zeta potential in the flotation of beryl with different collectors and salts was also extensively investigated.5"7 Previous infrared investigations by the authors8 disclosed that the orthosilicate beryllium mineral, phenacite, reacts with oleic acid to form a chemisorbed oleate monolayer on the mineral surface. Thus, chemisorption is the effective mode of adsorption in the phenacite-oleate acid flotation system. In contrast, neither chemisorption or physical adsorption of oleic acid occur on the surface of pure beryl as evidenced in this study. Efforts were subsequently made to determine the mechanism of activation and collector adsorption for HF pretreated beryl. EXPERIMENTAL PROCEDURES Large, white, terminated crystals of beryl were obtained from Madagascar through Ward's Co., Monterey, Calif. The crystals were broken into -60-mesh fragments in a porcelain mortar. Part of this prepared material was ground to a powder with a Fisher Grinder using an agate mortar and pestle. The powder was transferred to a graduated cylinder and mixed with 500 ml of distilled water. After 5 min, the colloidal suspension was separated from the settled particles by decantation and used as a stock for infrared test determinations. Adsorption tests were performed by first transferring 20 ml of colloidal suspension to 50 ml glass centrifuge tubes. The solids were then centrifuged out and the liquid was discarded. Then, the solids were pretreated with one molar HC1 or one molar HF. After 15 min, the solids were again centrifuged out. The mineral solids were washed free of residual acid by repeated centrifuging and water washing operations. Then, 20 ml of distilled water was added to the solids, and the resultant suspension was used for test purposes. In the preparation of mineral for flotation tests, 1.5 g of -60-mesh beryl was deslimed by removing the colloidal fraction by three successive water washes and decantations. Then, the coarse particles were pretreated with either one molar HCl or one molar HF for 15 min. The mineral was next washed free of acid with distilled water, and 20 ml of distilled water was added to the beryl prior to collector conditioning. The conditioning of mineral with collector was performed in 50 ml centrifuge tubes to which either NaOH or HC1 was added for pH modification. One drop (6.0 mg) of U.S.P. reagent grade oleic acid or 2 ml of 0.01 molar sodium oleate was added to the pulp and stirred at about 1500 rpm for 3 min at a

Jan 1, 1968

It is not often that a mining district is discovered, opened up, exploited and developed into a rich producer within the space of three or four years. Not until the year 1903 was the existence of the rich cobalt-nickel arsenides and silver of Northern Ontario even suspected by the mining public. But it is worthy of record that Dr. W. G. Miller, the man who has done so much to develop sanely and honestly the mineral resources of Ontario, pointed out [ ] the possibilities of this region at least two years before the first discovery was made. . Dr. Miller, then Professor of Geology at the School of Mining, Kingston, Ont., referred in these words to the district: "It will be seen from what has been stated on preceding pages that the district examined contains as great a variety of rocks as probably any part of the Province of equal area . . . Although few discoveries of economic minerals have been made in this territory, it may reasonably be expected that deposits of value will be found when

Jan 1, 1907

The term "timbered stope" is here meant to denote stopes in which timbering is the predominant feature of the mining method. Stopes with stull sets, as in the Hecla mine, are types of timbered stopes; these types are probably the best-known. Timbering stopes by means of square sets is not as common as formerly, as the system is not often necessary, yet there are good examples and large tonnages are being mined by the method. The square set may be utilized in ordinary overhand stopes if the orebody is suitable. At some mines, square sets have been abandoned in favor of top-slicing; and at others, the square set has superseded horizontal cut and backfilling. A drift, either in the wall or orebody, is necessary before opening the sill floor. In wide deposits, there may be a grillage of drifts and crosscuts, and at least one raise to the level above is needed in each stope for ventilation and handling timbers and filling. The square sets are filled with waste rock from the hanging wall, sorted from the ore, from development work, or from the level above. As a rule, little timber is recovered. The examples include the Butte district, Mother Lode of California, Bunker Hill & Sullivan, Hecla, and Morning mines.

Jan 1, 1925

By J. T. Eash, N. B. Pilling

As a group, the alloys of iron, nickel and carbon are, in application, one of the most versatile of the ferrous alloy family, and while many investigations have been made of their properties and structure only a few attempts have been made to show the microstructural relation over a wide range of composition. It is necessary at once to be clear about the kind of structural relation with which we are concerned. The equilibrium diagram provides quantitative data regarding structural make-up and its variation with temperature, but equilibrium structures often are far different from the technologically significant ones. This is particularly true of steels and cast irons, and some of the most important components of their structure may have no place in the diagram of equilibrium. The fugitive phases that result from transformation are dealt with in a highly detailed and descriptive manner in the S-curves originated by Bain. The present effort lies in a still different field, which is to portray the relation between sweeping changes in composition and in resultant structure, under controlled but nonequilibrium conditions of thermal treatment. The Guillet1 diagram presented in 1903 was the initial attempt at such a correlation and frequent references to this diagram can be found in the literature even though later work has shown it to require considerable modification. Kase2 published in 1925 a diagram that was based upon observations of furnace-cooled melts. At low carbon contents this diagram agreed fairly well with experience in showing pearlite to exist in alloys containing up to 6 per cent nickel, and completely austenitic steels at 24 to 28 per cent nickel. At high carbon contents, however, irons were indicated as being martensitic at around 2 per cent nickel and austenitic at 12 per cent nickel; these interpretations are open to serious question. Based upon experience with steels and cast iron, Wickenden3 suggested a diagram that agreed fairly well with Kase's in the steel range but which presented a wide departure from it in the higher-carbon, high-nickel regions. In its broad picture, the Wickenden diagram is an approach to "practical" structures. [ ] Reference may be made at this point to the efforts of Marshy to construct an iron-nickel-carbon equilibrium diagram by the coordination of scattered data, which are described at length in the monograph cited. None of these preceding attempts has appeared to meet the need for an exposition of the structural sequence that is encoun-

Jan 1, 1942

By Gilbert Santoro

In this study tantalum carbide filaments of various compositions in the fcc region were prepared by heating a tantalum wire in a measured amount of hydrocarbon vapor. Such properties as tensile strength, transverse-rupture strength, microhard-ness, lattice parameter, electrical resistivity, and magnetic susceptibility were measured as a function of carbon content. Some of these properties showed a maximum or a minimum between a carbon-to-tantalum molar ratio of 0.80 and 0.85, the composition range at which the color changes from metallic gray to gold. The recent literature has shown that in the large homogeneity range for the fcc phase of the Ta-C system there is a marked variation for such properties as microhardness,' electrical resistivity, ' thermodynamic properties,z'3 lattice parameter and superconductivity. In addition to the technological interest of these variations within a single phase, important theoretical benefits may ensue from a continuous investigation of properties vs stoichiometry in tantalum carbide and other refractory defect compounds, for example the effect of the metal-metal distance and crystal structure upon bond formation and electronic structure. Whether there is a similar variation of the tensile strength is of practical importance. Of theoretical interest would be the knowledge of how the magnetic susceptibility varies with carbon composition. Both of these properties, as well as the transverse-rupture strength, were determined for tantalum carbide filaments in the fcc phase region. The lattice parameter, the electrical resistivity, and the microhardness were also investigated and compared with values appearing in the literature. EXPERIMENTAL PROCEDURE Material Preparation. Tantalum carbide specimens of various carbon content were prepared by statically carburizing high-purity tantalum filaments in measured quantities of pure hydrocarbon gas. The filaments, which were 10 mil in diameter and 20 or 40 cm long, were heated by their own resistance at temperatures from 1800" to 2200°C using alternating current in some cases and direct current in others. Tantalum wire from two sources was used. One had a reported purity of 99.96 wt pct Ta. The ingot from which this wire was drawn had been electron beam-melted as the final step in its purification. The reported purity of the other wire, which was prepared by a powder metallurgical process, was 99.88 wt pct Ta. The impurities of both tantalum sources are listed in Table I. Spec-trographic-grade toluene or research-grade propane was used as the source of carbon. The apparatus for the carburization of the filaments is shown schematically in Fig. 1. The system was evacuated to 1 x l0-' mm of Hg when using the electron beam-melted tantalum and to less than 1 p when using the less-pure tantalum. Neither the difference in the base vacuum, nor in the hydrocarbon gas, nor in the tantalum filaments resulted in any detectable difference in the properties studied in this work. However, only the carbides prepared from the higher-purity tantalum were used in the magnetic-susceptibility determinations. Once the base vacuum had been reached, the system was flushed with the hydrocarbon and re-evacuated. For any desired composition of the carbide, hydrocarbon gas was allowed to leak into a constant-volume flask to a predetermined pressure. These pressures were measured by a Cartesian diver-type mercury gage with a range from 0 to 20 mm and with a scale expanded to nine times. The hydrocarbon gas was allowed into the reaction tube and the filament was quickly raised to the reaction temperature. The slack in the filament due to thermal expansion was taken up by drawing out the movable electrode with a screw mechanism. The filaments were kept at temperature from a few minutes to 200 hr. In the majority of cases the heating time was 6 hr. The reaction tube was cooled by cascading water on its outer surface. By means of an ammeter and a voltmeter the electrical resistance at the reaction

Jan 1, 1963

By Robert F. Mehl, Gerhard Derge

The gamma-alpha transformation in iron and iron-rich alloys is of such practical and theoretical importance that many papers have been published upon the subject relating to critical temperatures, transformation rates and accompanying property changes. Although crystallo-graphic studies are of less immediate practical usefulness, the opportunities which these offer to furnish data on the basic atomic movements which characterize the transformation are not to be neglected1. The early work on the crystallography of this transformation has been reviewed in the fourth paper of this series2; since then several important papers have appeared. Our present knowledge may be briefly summarized as follows. Kurdjumow and Sachs, working with a 1.4 per cent carbon steel3, established the orientation relationships subsisting between the face-centered gamma and the metastable tetragonal lattices in freshly quenched martensite, and between the face-centered gamma and the body-centered alpha lattices in tempered martensite. The orientation relationship observed in the latter case may be stated in terms of planes and directions observed to lie parallel in the two lattices: {111} ?//{110}a [110] ?// [111]a (This notation is used throughout as the most descriptive means of expressing the fact that any (111) plane of the gamma phase may be parallel to any (110) plane of the alpha phase, and that a [110] direction in a particular (111)? plane is parallel to a [Ill] direction in the corresponding (110)a plane.) From these relationships the atomic movements that transform the gamma lattice into the alpha may be inferred. In the present experiment these may be considered as consisting primarily in a shear of the atoms parallel to the {111} planes in [110]? Directions

Jan 1, 1937

By W. S. Steele

Vermiculite is a nonmetallic mineral of the mica family, probably related to biotite mica. Its occurrence has been noted at numerous places in the United States and in some foreign countries, but it can be said that vermiculite is of only moderately wide distribution. A laboratory and field survey of over 60 deposits in the United States by F. 1;. Schundler & Co., of Joliet, Ill., indicates that the purest deposit represented in this survey is on the property of the Zonolite Company at Libby, Montana The Zonolite Company is commercially active and the vermiculite it produces is sold as Zonolite. Hereafter, in this report, the word "Zonolite " will be used to designate the vermiculite produced by the Zonolite Company. Values given herein to Zonolite are peculiar to the vermiculite produced from the Zonolite Company's deposits. References to " vermicullite," are to he interpreted as covering the broad field covered by the Schundler survey. Composition and Characteristics of Vermiculite Vermiculite is an aluminum-nmgnesium silicate. The following typical analysis is published by the United States Bureau of Standards: silica, 41 per cent; iron oxide, 7; aluminum oxide, 18; magnesium oxide, 21; calcium oxide, 1; alkalis (sodium and potassium), 1; moisture, 11. Vermiculite breaks down into platelike formation in crushing and grinding operations. Its cleavage is basal. Crude, screened, dry Zonolit,e weighs between 80 and 90 Ib. per cubic foot; its specific gravity is 2.8 and its specific heat is approximately 2. The fusion point of Zonolit'e is 2462" F. Crude vermiculite contains between 7 and 9 per cent of chemically combined moisture. The instantaneous introduction of crude Zonolite into an expansion furnace at a temperature of between 1800" and 2000" F. transforms the combined moisture into steam, which in an effort to liberate itself forces all explosive expansion of the platelike crude material

Jan 1, 1934

By Gerald F. G. Sherman

The ore deposits of the Warren district, in which the mines of the Copper Queen Consolidated Mining Co. are situated, have been described in a number of technical publications, and will not be discussed here in detail. Certain of their characteristics, however, control methods of underground transportation and hoisting of ore. In the Copper Queen mine, the majority of the ore has occurred in a zone encircling the west boundary of the porphyry intrusion of Sacramento Hill. It has a width varying from 800 to 1,200 ft., and a thickness of about 400 ft. It reaches the surface in the older part of the mine to the northwest, but dips to the southeast, where it is reached at 1,400 ft. below the Czar collar, in its farthest extension at present developed on Copper Queen ground. There is one major extension from the northwest end of the zone toward the west along the Czar fault, and others of minor importance. Individual orebodies are scattercd through the zone in an eccentric manner, only matched by their own irregularities of form and size. Their most gencral characteristics are the softness of the ore and their grcat horizontal rather than vertical extent. It has been estimated that the average vertical thickness of ore in the Czar and Lowell divisions is between 30 and 35 ft. It is calculated by assuming it to be uniformly distributed over its horizontally projected area. In this zone, and for some distance above it, the ground has been subjected to intense alteration and intense but irregular oxidation. It has resulted in an enormous quantity of earthy or clayey material, which may be either ore or waste, which when wet is both heavy and tenacious. Below alteration, the ground is fairly hard, and the limestones contain primary ores differing from those heretofore considered typical of the camp, and which have not yet been thoroughly exploited. The mine production has been drawn from many orebodies spread over a great area.l A diagram map (Fig. I), of haulage drifts and loading stations, illustrates the situation in 1914.

Jan 1, 1916

By E. V. Crane

A tremendous volume of the metal rolled annually into sheets strips and coil stock finds its way to a host of stamping and manufacturing plants which are the quantity production units of the country. Considerable in volume, too, are the rolled and extruded rods which go into forging and manufacturing plants for conversion into the same general line: those widely sold metallic necessities and luxuries of the household, the office, transportation, farming and building construction. Yet, in spite of its age and its importance, the stamping trade has been doing its "engineering" largely by trial and error. Its distinctive method is shearing out and plastically working metal to finished shape in a few quick strokes with high loads and expensive tools which are warranted only by large quantities to be produced. The principal operations have many features In common with rolling and wire-drawing methods. Combinations of stresses are diffcrent, however, and details of operations are infinite in variety. An engineering study of the subject begins with stress analysis, but must go back to metallurgy for its foundation. A grouping of pressed-metal working operations according to whether the metal is (1) sheared, (2) bent, (3) drawn or (4) squeezed has proved useful. All of these groups include instances of both hot and cold operations. For discussions of metal working properties, the division between hot and cold working is taken as the recrystallization range of temperature. This, of course, brings tin, lead and often zinc into the hot-work range at or near room temperature. The outstanding hot-working press field is in forging: particularly of brass; all of which is included in the squeezing group. Shearing Operations The shearing group of operations, including blanking, piercing, trimming, shaving, slitting, shearing, notching, parting and numerous variations and combinations of these enters once or more into the production schedule of practically every stamped or forged article. The transverse stress, set up in shearing, as shown in Fig. 1A, is a combination of an angular compressive thrust and a tensile stress which is also at an

Jan 1, 1931

By Kenelm C. Appleyard

In introducing to an American audience a description of the work done in dry coal separation in England and in Europe generally, it is perhaps desirable to give a short history of the development outside the United States of the particular processes with which the author is connected, and perhaps to stress a little the differences in the nature of the conditions to be faced. England actually presents one set of problems and the Continent of Europe another, since the character of the coals to be treated is entirely dissimilar, and the attitude of the coal industries towards coal preparation is also dissimilar. England for generations has been working by hand good seams of clean coal of the highest possible quality and has not felt any pressing need to clean its coal. Most Continental countries, however, especially in Central and Western Europe, have been working friable and often very dirty coals for so long that a washery is accepted as a part of the normal equipment of a colliery, with the result that the art of wet washing has reached a high state of perfection, particularly in Belgium and Germany. The advent of machine mining has intensified the problems to be faced in all countries, and in England has been coupled with the working out of the best seams in the older coal fields, thus bringing about the necessity of working thinner and dirtier seams with resultant difficulties as regards marketing the products, while Poland, with clean and well prepared coal, has in recent years been attacking established British markets in Scandinavia. In recent years, therefore, interest in coal preparation has been steadily gaining ground in England, although it has not yet reached Continental dimensions. Broadly speaking, the differences in preparation problems between England and the Continent boil themselves down to one of size. In England, for example, with the exception of the Kent coal field, the proportion of coal of a size less than ? in. to the coal less than 2 in. is very much less than on the Continent, and since the principal difficulties in dry cleaning lie in the fines it is easier to produce good figures on

Jan 1, 1931

By Virgil R. D. Kirkham

NoRth America has for many years led the world in phosphate production, but with development of African deposits and their marketing conditions with respect to European countries, this leadership will shortly pass to Africa. Algeria, Egypt, Tunis, and Morocco have large phosphate reserves and a correspondingly large production because of easy mining and a ready European market, which was developed during the war. An increase in home consumption is destined to develop for the eastern American fields, and the countries of the Pacific will provide a market for the western producers. New processes indicate a decrease in fertilizer costs, which will encourage a more widespread domestic use and assure better marketing conditions. The African deposits, although benefited by a water haul, have the disadvantage of being isolated from a source of acid so that the crude rock is shipped from Africa to its destination, whereas in the United States the chief product shipped is acidulated rock or various types of superphosphatic fertilizers, The principal types of phosphate deposits used in the manufacture of fertilizers are guanos, apatite, phosphatic marl, phosphatic limestone, phosphatic shale, and phosphate rock which is also known as phosphorite. Some of these deposits are found on each of the continents; Table 1 gives their occurrence, age, location, character, extent, etc. Most of the information found in this table represents a compilation of information published elsewhere in a different form and widely scattered.

Jan 1, 1925

By G. Van Esbroeck, M. Van Weyenbergh

The copper mines of the Katanga region in the Belgian Congo lie along the same mineralized belt as those of Northern Rhodesia. There are two distinct types of deposits in that belt, the dolomitic and the quartzitic. In the dolomitic type the metallic minerals are found in a dolomitic limestone country rock. Through oxidation and enrichment, large deposits of high-grade oxidized copper ores were formed, some of which are being worked by the Union Minière du Haut Katanga. Such deposits are all in Katanga. The quartzitic deposits are found in Katanga and Northern Rhodesia. Here the primary mineralization occurred in sandstones and quartzites, in horizons stratigraphically lower than the dolomites. These rocks are not favorable to secondary enrichment and the oxidized zone is poorer than the sulphide zone, which alone contains the ore. There are also in Katanga a few ore-bearing veins. One of them is being worked in the Prince Leopold mine at Kipushi. Prince Leopold Mine The Kipushi ore body fills a fault vein and invades the wall rocks more or less extensively by metasomatic replacement. The vein strikes north-northeast and south-southwest and dips to the west. The variable dip averages 60' to a depth of 300 ft., and more uniformly 80' below 400 ft. In the upper section the average width is 200 ft. and below the width is about 150 ft. The length of the ore body is 2300 feet. The eastern side of the vein—the footwall—is dolomitic and contains irregular masses of ore sometimes extending 100 ft. or more from the main

Jan 1, 1940

By M. Van Weyenbergh, G. Van Esbroeck

The copper mines of the Katanga region in the Belgian Congo lie along the same mineralized belt as those of Northern Rhodesia. There are two distinct types of deposits in that belt, the dolomitic and the quartzitic. In the dolomitic type the metallic minerals are found in a dolomitic limestone country rock. Through oxidation and enrichment, large deposits of high-grade oxidized copper ores were formed, some of which are being worked by the Union Minière du Haut Katanga. Such deposits are all in Katanga. The quartzitic deposits are found in Katanga and Northern Rhodesia. Here the primary mineralization occurred in sandstones and quartzites, in horizons stratigraphically lower than the dolomites. These rocks are not favorable to secondary enrichment and the oxidized zone is poorer than the sulphide zone, which alone contains the ore. There are also in Katanga a few ore-bearing veins. One of them is being worked in the Prince Leopold mine at Kipushi. Prince Leopold Mine The Kipushi ore body fills a fault vein and invades the wall rocks more or less extensively by metasomatic replacement. The vein strikes north-northeast and south-southwest and dips to the west. The variable dip averages 60' to a depth of 300 ft., and more uniformly 80' below 400 ft. In the upper section the average width is 200 ft. and below the width is about 150 ft. The length of the ore body is 2300 feet. The eastern side of the vein—the footwall—is dolomitic and contains irregular masses of ore sometimes extending 100 ft. or more from the main

Jan 1, 1940

By A. G. Weber, R. L. Ledbetter, A. L. Hicks

A procedure which makes use of both analog and digital computers has been developed for predicting the pressure-production behavior. of water-drive reservoirs. The electric analyzer is used for matching the past pressure and production history of the reservoir and inferring the physical characteristies of the aquifer. When the history has been matched, a .set of base curves called influence functionce" are derived and the future behavior of the reservoir is calculated from these curves. INTRODUCTION Electric analog methods are particularly well-suited for complex water-drive problems. Like all other methods of analyzing water-drive reservoirs, however, analog methods are subject to certain limitations. One of the more obvious and serious of these results from inaccurate or insufficient knowledge about physical characteristics of the reservoir and aquifer. However, it is not insurmountable because the unknown characteristics can usually be inferred from the reservoir's previous behavior. Simons and Spain have shown that even with scant reservoir data and limited production history, electric analyzer studies can provide useful and reliable results. Aside from this limitation on analyzer predictions, the main disadvantage has been lack of a technique for keeping predictions abreast of latest production forecasts. Pressure behavior of a reservoir depends on the rate at which fluid is withdrawn; it is therefore necessary to specify the future withdrawal schedule before the future pressure behavior can be calculated. Conventionally, the electric analyzer predicts pressure behavior for a specific production schedule. If this schedule is abandoned in favor of some new one, as is frequently the case, either the study must be rerun or results adjusted in some manner. The usual procedure is to predict pressures for several different forecasts covering a wide range of production rates. Pressures for specific rates other than those studied can then be approximated by interpolating between the analyzer predicted curves. However, reliability of this type of prediction is doubtful. This paper describes a technique for predicting future behavior of water-drive reservoirs that retains all advantages of electric analyzer analysis and eliminates the main disadvantage. That is, the analyzer is used conventionally to infer unknown reservoir parameters from the pressure history, but not to predict the future behavior directly. Instead, a derived set of base curves, called influence l'unctions, can be used to calculate future behavior for any production schedule.

By Nicholas J. Grant, Olaf Troili, John Chipman

D. C. Hilty (Union Carbide & Carbon Research Laboratories, Niagara Falls, N. Y.)—How does this effect of silica compare with the effect of silica in combining with the lime in the slag to reduce the activity of CaO, thereby affecting the first equation? John Chipman(authors' reply)-—That is the object of showing this effect for slags of two different basicities. In the more basic, the silica is more firmly tied up in the slag and is less easily reduced. It is therefore less able to interfere with desulphurization. The important point is that silica is acting in two ways. Of course it is an acid and as an acid it ties up lime and in tying

Jan 1, 1952