Search Documents

By Edgar Marburg, William R. Webster

The desirability of bringing about greater uniformity in specifications governing iron and steel is generally recognized, and has found expression within recent years, in the efforts of numerous technical societies in that direction. When the International Association for Testing Materials was organized at Zurich in 1895, a committee was appointed, charged as follows: " On the basis of existing specifications, to seek methods and means for the introduction of international specifications for testing and inspecting iron and steel of all kinds." The American representation on this international committee consisted originally of five, and now of eight members. In view of the magnitude and importance of the subject, the Executive Committee of the American Section of the International Association for Testing Materials, since incorporated as the American Society for Testing Materials, appointed a committee of 34 members, including the American members of the above-named international committee, to frame standard American specifications for iron and steel. This committee reported on specifications for (1) Structural Steel for ridges and Ships; (2) Structural Steel for Buildings; (3) Open-Hearth Boiler-Plate and Rivet-Steel; (4) Steel Rails; (5) Steel Splice-Bars; (6) Steel Axles; (7) Steel Tires; (8) Steel Forgings; (9) Steel Castings ; (10) Wrought-Iron. These specifications were designed to be fairly representa-tive of the best current American practice, and were adopted by letter-ballot of the Society in August, 1901. The leading engineering societies have participated at various times in the discussion of these specifications and have lent valuable assistance through the appointment of special committees on like, or closely related, subjects. The American Society of Civil Engineers discussed the spec-

Jan 1, 1905

By Gearge C. Wallick

This paper describes experimental procedures for the calibration of capillary tubes to be employed as comparison standards in gas flow-rate measurements and considers several types of flow which were observed in the calibration of seven capillaries of varying diameter. It is shown that under certain experimental conditions deviations from Poiseuille flow are observed which may not be attributed to turbulence, and that this flow behavior may be described empirically by introducing the classical kinetic energy correction into the Poiseuille equation. INTRODUCTION Techniques have been developed for the measurement of the volume rate of flow of nitrogen through glass capillary tubes as a function both of the differential pressure applied and of the absolute gas pressure. Capillary tubes thus calibrated are frequently used to determine the rate of gas flow through a porous sample in the measurement of slip-corrected permeability. The purpose of this note is to describe the calibration procedure and to discuss some observed deviations from the ideal flow behavior predicted by the Poiseuille equation. EXPERIMENTAL PROCEDURE The volume flow rate of nitrogen as a function of the differential pressure was determined experimentally for a series of seven glass capillary tubes of varying diameter. As is shown in Table 1, the capillary radii in the series ranged from 0.004 cm for K1 to 0.07 cm for K7. The capillary tubes were cut from capillary tubing purchased on special order from several manufacturers and the bore radii were determined by microscopic measurement. The gas volume flow rate was measured for each capillary tube at a series of differential pressures in the range from 0 to 3 cm of mercury and at average absolute pressures of 1.0, 2.5, 4.0, and 6.0 atm. Experimental Procedure for Small Capillaries A schematic diagram of the apparatus used to calibrate the three smallest capillaries, Kl, K2, and K3, is shown in Fig. 1. By means of a standard Ruska Instrument Corp. volumetric pump (equipped with a synchronous motor drive, two stages of gear reduction, and a quick-change lathe gear box), nitrogen was displaced by mercury from a metal cell immersed in a constant-temperature bath. The pump, the line to the cell, and a part of the cell were filled with mercury. As mercury was forced into the cell, it displaced nitrogen which passed through the capillary tube being calibrated and into a large container with a volume of approximately 30 liters. Since the volume of this container was very large compared to the total volume change of the gas resulting from the action of the displacement pump, the absolute pressure of the system was essentially constant throughout any one run. Prior to any determination this pressure could be set at any desired level by means of an auxiliary nitrogen cylinder. The differential pressure across the capillary was measured with a Meriam Red Oil manometer and recorded together with the corresponding pump displacement rate which was equal to the gas flow rate. By repeating this process for a series of different displacement rates at each of the absolute pressures of interest, the data necessary for plotting the calibration curves for capillaries K1, K2, and K3 were obtained. All calibration measurements were made in a constant temperature room to minimize errors due to temperature fluctuations. In each run. the flow was maintained until equilibrium was established. Experimental Procedures for Large Capillaries The flow rates through Capillaries K4, K5, K6, and K7 required to obtain the pressure drops desired were larger than could be obtained from available constant displacement pumps, and it was thus necessary to employ an alternative calibration procedure. The arrangement of apparatus used in calibrating these capillaries at an average pressure of one atmosphere is shown in Fig. 2. Each capillary was calibrated by flowing nitrogen through the capillary and recording the differential pressure as a function of the flow rate. 'The differential pressure was measured with a Meriam Red Oil manometer and the flow rate was determined by collecting the effluent gas over water at constant pressure and recording the increase in volume per unit time after an equilibrium had been established. Appropriate corrections were made for the

Jan 1, 1953

By Joseph R. Stephens

Deformation substructures of' polycrystalline tungsten, W-2, 9, and 24 pct Re, and W-3 pct Ta were studied by tra?zsrnission electron microscopy. The stress-strain curve for unalloyed tungsten showed gradual yielding followed by work-hardening. Electron nzicrographs indicated a gradual increase in dislocation density with increase in strain up to 5.0 pct. Dislocations, although frequently jogged, were straight over moderate distances and were in a randorn array. Stress-strain curves for alloy specimens of W-2 and 9 pct Re and W-3 pct Ta exhibited a drop in stress at yielding followed by only slight work-hardening. Electron micrographs of these specimens after strains of 0.05, 0.1, and 0.5 pct revealed no change in dislocation substructure from the unstrained specimens. After 2.0 pct strain, the three alloys exhibited dense networks. W-3 pct Ta was characterized by straight, frequently jogged dislocations comparable with the dislocation structure in unalloyed tungsten after a similar amount of strain. In contrast, W-2 pct Re exhibited dislocations that contained widely spaced jogs, while W-9 pct Re had developed a cell structure after the relatively srnall strain of 2.0 pct. The W-24 pct Re alloy contained a few dislocations after 0.1 pct strain, while after 0.5 pct strain twins were evident. Dislocation slip bands apparently preceded the twins. The stress-strain curve for the alloy indicated that twinning commenced after approximately 0.25 pet strain. These results indicate that the primary effect of low rhenium concentrations (2 and 9 pct) in tungsten is to increase dislocation multiplication after macroyielding by reducing the Peierls-Nabarro force (lattice resistance to dislocation motion). The dislocation bands that precede twins in W-24 pct Re may be caused by localized internal stresses resulting fro a metastable structure, for example, clustering of rhenium atoms. The effect of high rhenium additions (22 a 65 pet* Rproperties of tungsten. Klopp, Witzke, and Raffo5 reported bend transition temperatures as low as -100°F (200°K) for dilute electron-beam-melted W-Re alloys tested in the worked condition. Recrystalliza-tion increased the bend transition temperature, but alloys with 2 to 4 pct Re were still markedly superior to unalloyed tungsten. Fractographic examinations of tungsten and W- 3 pct Re and W- 5 pct Re alloys by Gilbert 6 revealed that these low rhenium alloys showed a greater tendency toward cleavage failure than did tungsten. Garfinkle 7 showed that rhenium additions, up to 9 pct, to (100) oriented tungsten single crystals increased the proportional limit stress and decreased the flow stress and the rate of work-hardening. In addition, while deformation in unalloyed (100) oriented crystals apparently involved both (110)100) and (112) slip, crystals with rhenium contents of 5 andpct or more deformed primarily by (112) slip. The mechanism by which high and low rhenium additions affect the mechanical properties of tungsten is still not well-established. The present investigation was undertaken to determine by transmission electron microscopy the effects of low rhenium additions, 2 and 9 pct, and a high rhenium addition, 24 pct, on dislocation substructure in the early stages of deformation of polycrystalline electron-beam-melted tungsten. Unalloyed tungsten and a W- 3 pct Ta alloy were included for comparison. EXPERIMENTAL PROCEDURES Materials. Triple electron-beam-melted tungsten, W-2, 9, and 24 pct Re, and W- pet Ta were used for this investigation. Chemical analyses of the cast ingots are given in Table I. A description of the starting metal powders and melting and fabrication pro-cedures for unalloyed tungsten and the W-Re alloys is reported.5 The W-3 pet Ta alloy was processed in a similar manner. Compression specimens measuring 0.300 in. (7.6 mm) in length by 0.130 in. (3.3 mm) in diam were machined from swaged rods. All alloy specimens were annealed in a vacuum of 8 x 10- 6 Torr (10'2iVper sq m) for 1 hr at 3600°F (2255°K). The recrystallized grain size ranged from 0.06 to 0.08 mm diam for the alloy specimens. Unalloyed tungsten was annealed at 2400° F (1589°K) for 1 hr to produce a recrystallized grain diameter of approximately 0.12 mm. Specimens were electropolished in a 2 pet NaOH solution to a diameter of 0.125 in. (3.18 mm) to remove surface notches resulting from grinding and to improve reproducibility of t data. The ends o the compression specimens were ground flat, parallel to each other, and perpendicular to the longitudinal axes with 4/0 emery paper. Compression Tests. The compressive stress-strain apparatus used for compression tests is described in detail by Stearns and Gotsky.9 Room-temperature compression tests were conducted at a crosshead speed of 0.01 in. per min (0.25 mm per min).

Jan 1, 1969

By Sam F. Harrison

Most hydraulic system malfunctions make their presence known by sending out warnings that are loud and clear to the initiated mechanic, according to Aeroquip Corp. service engineers. To detect problems in many systems, they suggest that the use of four senses-sight, smell, hearing and touch-and a knowledge of how to interpret the information gathered are all that's needed to identify hydraulic malfunctions.

Jan 3, 1978

By J. F. Ednie

SCRAP metals to the value of more than a billion and a half dollars were recovered in the United States in 1939 for further use in industry. Few people have any true conception of the magnitude of the secondary-metal industry as related to that engaged in the production of the primary, or virgin, metals; of its importance, particularly when a shortage of primary metals exists, as at present; or of the advance that has been made in standardizing and improving the quality of its products. Of the iron and steel produced in the United States in 1939 (the data used in this article are largely taken from Bureau of Mines reports for that year) just over 50 per cent came from scrap and slightly less than 50 per cent from ore. Of the principal nonferrous metals-aluminum, anti-mony, copper, lead, nickel, tin, and zinc-63 per cent came from domestic ores and 37 per cent from scrap. Fig. 1 presents graphically the relative tonnage and value of primary and secondary production of ferrous and nonferrous metals. In this chart only purchased secondary metals are considered, the figures being exclusive of "home" or "plant" scrap which amounts to rather large figures in the iron and steel industry. Incidentally, the chart shows that from the tonnage standpoint the iron and steel industry is some twenty times larger than the nonferrous industry, though with regard to the value of the product the ratio drops to about two to one.

Jan 1, 1941

During the past 60 or 90 days, the metropolitan newspapers have published much concerning unemployment throughout the nation and the efforts of the Army and various other bureaus for finding work for the returning soldiers. The United States Employment Service has 2000 bureaus throughout the country, which Nathan A. Smyth, Assistant Federal Director, states have placed more than 2,400,000 persons in employment. The Engineering Societies Employment Bureau, which, since December, 1918, has been endeavoring to put all returning engineers in touch with employers who need efficient men, has produced results that are very gratifying to the Secretaries of the four Founder Societies under whose direct management the Bureau operates. During this period, 1615 men have registered at the Bureau's office in the Engineering Societies Building; not all of these, however, are unemployed. Many are ex-army and navy men, who in passing through New York on their way home, look over the field in the hope of making a change for their own benefit before returning to their former positions. During this period, 427 positions vacant have been filed, 2300 of which positions have been filled from the men registered. The letters mailed by this Bureau amount to about 1000 a month and the number of personal calls at the office, 1600. The lowest number of positions filled has been in mining, but the lowest number of registrations is also from mining men. While in February idleness throughout the nation was increasing at the rate of 35,000 a week, under date of Mar. 7, Arthur Woods, a special assistant to Secretary of War Baker, states that there is a material improvement in the unemployment situation and that the problem is no longer a serious one. It is recognized that' the improvement wrought in each individual by his military training and experience has so increased his value that it is 'not only unfair, to ask these men to accept their old jobs at the old wages, but it is probably very unlikely that they will be willing to do so. This plain statement of improvement may not carry conviction to everyone but a concrete example will show its validity. Take the example of a young man under 21, bright and intelligent, with only a high-school education who was employed, before being drafted, on purely manual labor. He shows up well under military training and is made a corporal; he makes good and is appointed a sergeant; and finally becomes top sergeant, which requires him in many ways to handle the entire company of 250 men. The result is; even if he has not been tried by the fire of battle, he comes out of the army with a feeling of self-confidence and capacity that was entirely lacking when he went in and he has had actual experience in handling a larger body of men than the average mine foreman at twice his age, and he has had twice the average amount of detail work to take care of.

Jan 4, 1919

By E. H. Kelton, R. D. Grissinger

In designing structural members of steel and some other materials the design engineer has available recognized values of elastic modulus and safe working stress that may be substituted in well-known engineering formulas to give him desired cross-sectional areas and deflections for a particular part. Zinc, on the other hand, has no generally recognized modulus. It flows under continuously applied loads. Therefore, the designer of structural members must use a range of working stresses depending on the continuous load and the amount of permissible distortion. The only method of obtaining these values is by creep testing. Creep testing of zinc has been carried on for some 20 years by this laboratory, covering a wide range of zinc and zinc alloys. Types of test included tension, compression, and simple and cantilever beams at temperatures ranging from o to I50°C. Specimen conditions ranged from as-cast or as-rolled to accelerated aged in steam or dry air. Effects of plating were investigated also. It is not the intention of this paper to expound all these factors but rather to present the final data on well-known zinc die-casting alloys and to suggest means of applying these data to engineering design. Early Work In the early work on creep testing of zinc, the direct-loading tension method was used. However, direct loading of die castings was unsatisfactory because of the high loads required. For instance, a standard die-cast tension bar having a cross-sectional area of about 0.049 sq. in. would require a direct load of about 1000 lb. for a unit stress of 20,000 lb. per sq. in. Also, tests were made at nominal room temperature, but normal variations caused fluctuations greater than those due to experimental error or other causes, so that control of this variable within ±1/2°C. seemed essential. These two factors led to the development of an apparatus described by J. Ruzicka,' in which the specimens were loaded by means of a lever and were held at constant temperature by means of an oil bath. While Ruzicka's apparatus yielded excellent check results, it seemed desirable to have some setup by which literally hundreds of die-cast specimens could be tested at the same time. This would permit the conducting of a number of low-load tests designed to run 10 years or longer and still leave capacity for current high-load work. Beam testing in a constant-temperature room was the answer. Test Method Preliminary work indicated that die-cast beams of various lengths and cross scctions yielded the same result within reasonable limits regardless of whether they were tested as simple beams, uniformly loaded beams, or cantilevers. Accordingly, the simplest type was adopted. This was a,

Jan 1, 1945

By R. H. Smith, A. C. Polk

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By A. C. Polk, R. H. Smith

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By Albert J. Phillips

FOR the most part, recent changes in nonferrous physical metallurgy have been gradual and of a transition nature rather than abrupt modifications of existing methods. Development of new alloys containing vital constituents in what formerly would have been considered minute amounts has necessitated more precise control of metallurgical procedure than ever before. Realization of the remarkable effects of minute amounts of specific foreign elements in many alloys has brought about a revolutionary control in the selection of even the most commonplace raw materials. In addition, recognition of the widespread occurrence of precipitation hardness in metal systems, and the utilization of many of these, has emphasized not only the need for precise temperature control but also the necessity for considering the time factor in its effect upon properties in the treatment of most metals. These needs have caused the development and widespread installation of equipment that permits precision of control undreamed of a generation ago.

Jan 1, 1935

By James E. Mills

In the work of exploring certain gold-bearing gravels in the American Valley, Plumas Co., California, entrusted to my charge by Prof. A. Agassiz, of Cambridge, and Q. A. Shaw, Esq., of Boston, it became necessary to sink a shaft through loose materials containing in some layers large quantities of water, and I have been compelled to devise a new method which has proved successful and may be of service elsewhere.

Jan 1, 1885

By F. A. J. Fitzgerald

In any kind of furnace the question of preventing the loss of heat is important, for no matter how the heat is obtained it costs something; and consequently, other things equal, that furnace is most desirable which uses the greatest percentage of the total heat generated for the particular object in view. In the furnace which uses electricity for the generation of heat the importance of preventing losses of heat is very much greater than in any other. To generate 1,000 kg-cal. requires an expenditure of 1.16 kw-hr., and consequently the cost per calorie is always expensive when electricity is used for heating. In heating any material in a furnace a general rule is that the generation of heat should be as rapid as possible. In any given furnace the heat-losses may be expressed as so many watts, and, therefore, the longer it takes to heat the furnace-charge the greater the losses will be. Suppose that a furnace contains a charge to be heated to 1,500°C. and that the average loss of heat is at the rate of 100 kw., then if the process of heating the charge takes 1 hr. the losses will amount to 100 kw-hr.; but if by using a more rapid generation of energy the charge can be heated in 30 min. the losses will amount to 50 kv-hr. An example from experiments on a certain process may be given to illustrate this point. The problem was simply to heat a furnace-charge to a certain temperature, and experiments were made to determine the effect of increasing the rate of generation of energy and comparing the kilowatt-hours required to heat a given charge. Here are typical results : Rate of Generation Energy Per Kg. of Energy. of product 88 kw. 1.7 kw-hr. 93 kw. 1.6 kw-hr.

Jan 1, 1913

By Oliver S. North

Reserves of perlite rock in the western section of the United States are immense. A geological report prepared for the Union Pacific RR showed proved tonnage of over 400 million tons in southern Nevada alone. Yet the perlite industry is not large, and most of the mines are relatively small. There are indications that perlite processing, thus far largely in the hands of relatively small com¬panies, is becoming concentrated in a few large companies. For economic reasons the bulk of perlite sold in crude form has come from three or four pro¬ducers, although many individual operators have sold small quantities to limited lists of purchasers. Perlite is one of ultra-lightweight aggregates. Owing to its outstanding qualities as an aggregate, variety of uses, and ultimate economy of use, it has enjoyed considerable popularity in this country in recent years. Marked foreign interest also has been evinced in this material.

Jan 2, 1955

By T. E. Leontis, J. P. Murphy

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,' in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20' to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200' and 250°C. (392' and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures' The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946

By J. P. Murphy, T. E. Leontis

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,' in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20' to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200' and 250°C. (392' and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures' The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946

By Charles T. Holland, David A. Olsen

Considerable work has resulted in the development of a formula by which the strength of coal pillars for an L to T ratio of up to 12 may be estimated. One of the factors involved in this formula is the coefficient of friction between the coal pillar and the adjacent rock with which it is in contact. This paper presents the results of studies on sandstone, limestone, shale and coal and the coefficient of friction between coal and the other three under wet and dry conditions. With the coefficients of friction thus determined and the use of results obtained earlier by Meikle and Holland, it seems probable that coal pillar strength may be more closely estimated. Several investigators1-3 have found that the com-pressive strength of cubical coal specimens can be correlated by an equation such as

Jan 1, 1969

By Victor A. Phillips

A series of strips of a Ni-12.7 at. pct A1 alloy were Prepared containing cubical y'(NisAl) precipitates with edge lengths from 60 to 500A. A particle-free solution-tveated strip was included for cornparison. They weve cold-rolled 95 pct and the effects of particle size on the isochronal (1/2 hr) annealing behavior between 300° and 950°C studied (by hardness and light and electron microscopy). It ulas inferred that the particles deformed with the lnatvix becoming lamellae which remained coherent. Comparison with published data fov pure nickel showed that aluminum greatly re-tavded softening and recrystallization, but it made little difference whether or not particles were present. The presence of pakticles led to a heterogeneous distribution of precipitates after annealing at 700" to 750°C. Recovery was not detected. Recrystallization occurred by the growth of new grains into unrecrys-tallized material. In a previous study by the author,' the growth of Ll2-type ordered yl(Ni3Al) precipitates was followed in Ni-12.7 at. pct A1 alloy as a function of aging at 600" and 700°C. The particles were showo to be cubical in shape in all sizes from 50 to 3000A and remained coherent. This work was used as a guide in preparing the starting structures for the present study of the effect of these particles on the annealing behavior of heavily cold-rolled strip. Another question of present interest was whether dislocation and particle hardening were additive, since the structures before rolling ranged from solution-treated to peak-aged to overaged. Also, precipitation might occur on annealing after cold-rolling. Reference may be made to other papers2"5 for previous work in this relatively unexplored field and only some recent work will be mentioned her:. phillips2 studied the effect of deformable 0 to 590A-diam cobalt particles on a Cu-3.23 pct Co alloy rolled 95 pct and found that the particles, which rolled out into thin lamellae, impeded softening and recrystallization. Tanner and servi3 likewise studied the annealing of cold-swaged Cu-2 pct Co alloy containing 150A-diam particles and found impeding effects. Haessner et a1.,4 on the other hand, found that incoherent 2-p-diam non-deformable particles of B4C (0.04 vol pct) tended to increase the rate of recrystallization of copper rolled up to 95 pct reduction. They attributed this to the formation of new grains at the particle interfaces. Humphreys and artin' found that nondeformable silica particles in copper rolled to 30 pct reduction accelerated recrystallization if the particle spacing was large and retarded it if the spacing was smaller. Haessner et a1 4 also studied a rolled Ni-Cr-A1 alloy; however, the particles of y'(Ni3Al)-type precipitate were not put in before rolling, but separated during the isothermal annealing at 750°C. No previous work appears to have been carried out on the effect of y' (Ni3A1) particles on the annealing of Ni-A1 alloy. Hornbogen and ICreye7 redetermined the solubility c of aluminum in nickel as a function of temperature T and showed that it was given by c = 32.6 exp(-1940/RT). This relation gives aluminum solubilities of 15.1, 14.2, 12.0, and 10.7 at. pct at 1000°, 900°, 700°, and 600°C, respectively. The phase precipitated from the nickel-rich solid solution is fcc y1 (Ni3A1) which has a Cu3Au -type ordered structure8 and remains ordered up to 1000°C.B EXPERIMENTAL PROCEDURE The alloy used was identical with that used before. Chemical analysis showed 6.27 wt pct (12.71 at. pct) Al, the principle impurities being 0.065 pct Fe, 0.022 pct Co, 0.020 pct Cu, and 0.004 pct C. Bar stock of 1 in. diam was cold-swaged to % in. diam, cold-rolled to 0.300-in.-thick strip, and annealed at 900°C in dry hydrogen. It was cold-rolled to 0.100-in. thickness and solution-treated for 1 hr at 1000°C while sealed in a quartz tube in argon, quenching in iced brine with the aid of a device to snap off the nose of the tube. Lineal analysis gave an average grain size of 0.055 mm. Pieces of strip were aged at 700°C in vacuo for 30 min, 51/4 hr, and 1 week to produce nominal average particle widths of 60, 150, and 500A, respectively, as known from the previous work.' The average diamond pyramid hardness was determined. The heat-treated strips were rolled from 0.100 to 0.005 in., a reduction of 95 pct, and the rolled strips stored at about -5°C. Small pieces were annealed within 1 week for 30 min at temperatures from 300° to 950° ±2°C in a horizontal vacuum furnace. Strips were withdrawn into a cooling zone, giving an estimated initial cooling rate from 950°C of about 50°C per sec. Average diamond pyramid hardnesses were determined on a lightly electropolished spot on the surface of each strip using 300-g load. Each point on the softening curves represents a separate annealed specimen. Sections containing the rolling direction were examined by optical metallography. Selected specimens were electrothinned to the center plane' and examined by transmission at 100 kv in a Siemens Elmiskop I electron microscope. It is well-known that changes in the structure tend to occur when a deformed strip is electrothinned below a thickness of a few hundred angstroms, although this is less serious with a material such as nickel which has a high melting point, and also is apt to be less serious when particles are present. Observations were nevertheless confined to thicker regions of the foils with estimated thicknesses over 1000A. No changes were observed due to beam exposure.

Jan 1, 1968

By A. E. WALKER

SOME eighty years have elapsed since the discovery of the Clifton magnetite deposit. For a few years about the time of the Civil War it was mined for iron ore. most of which was smelted on the property. Since risen the small exposures of ore in the old cut. test pits, and on the dumps have been examined by various prospectors. The M. A. Hanna Co. first became interested in the possibilities of the deposit when we discovered the large area of strong magnetic anomalies caused by the margnetite bed, indicating a size that would support a commercial operation. In 1940 we made a detailed magnetometer survey of the area. and the deposit was diamond-drilled. The main ore lied was found to be 1500 ft. long, to average 60 ft. thick, and to dip southeast at an angle of about 40 deg. The thickness of the bed is irregular in wavy folds both along the strike. and down the dip. Faults occur at both raids of the main deposit.

Jan 1, 1943

By L. F. Porter, G. J. Dienes

The effect of netltron irracliation on mart ensite transformation in the iron-nickel system was studied by means of electrical resistance and magnetic induction measuremertts. Irradiation lowers the M8 temperature of the allay, causes changes in the electrical and magnetic properties of the high-temperature phase which indicate either an accelemtion of phase separation or a clustering of nickel, and enhances strain recovery on specimens partially transformed to martensite prior to irradiation. Possible mechanisms to account for the effects; are discussed. 1 HERE is a good deal of evidence to indicate that neutron irradiation is capable of affecting phase changes in metals and alloys. While the mechanism of the effect often is not well understood, such studies hold promise of improving our understanding not only of irradiation damage but also of the phase changes involved. To date systematic and detailed investigations have been made of the influence of nuclear radiation on order-disorder transformations in the copper-gold, nickel-manganese, and copper-zinc system, and on precipitation reactions in the copper-iron, nickel-beryllium, and copper-beryllium system.' These solid-state reactions are diffusion controlled and the results can be explained largely on the basis of enhanced diffusion due to the presence of irradiation produced vacancies. Reversion of low-temperature eutectoid phases to the high-temperature phase has been observed in the fissionable uranium-molybdenum and uranium-niobium systems.2 Here it is necessary and logical to postulate a displacement spike mechanism to account for the effect. The only case of irradiation induced diffusionless transformation in metals is the allo-tropic transformation of p to a tin reported by Flee-man and Dienes. 3 They found that neutron irradiation markedly decreases the incubation time for transformation, but the mechanisnl is not well understood. Another diffusionless transformation which one might expect to be influenced by neutron irradiation is the martensite transformation. This transformation is known to be sensitive to strain, structural hardening, and the presence of imperfections.6,7 Since the transformation is diffusionless, one also

Jan 1, 1960

By J. Waldman, M. B. Bever, A. K. Jena

The heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of one solid solution have been measured by tin solution calorimetry. The heats of formation are analyzed in terms of the quasichemical theory. If the enthalpy diffel-ence between a hypothetical fcc form and the hcp form of cadmium is taken into account, this analysis does not lead to the conclusion put forth in the literature that electronic effects make significant contributions to the heats of formation of silver-rich Ag-Cd solid solutions. The temperature dependence of the heats of formation is appreciable and negative near 78ºK, but decreases gradually to nearly zero abore 400°K. The relative partial enthalpies per grarn -atom of silver at 541°K and cadmium at 532" and 541°K in tin have also been determined. THE composition range of the silver-rich Ag-Cd solid solutions stable at room temperature extends to about 40 at. pct Cd. Heats of formation of these solid solutions at 308" and 723°K have been measured by solution calorimetry.1,2 Heats of formation for an average temperature of 800°K have also been calculated from vapor pressures.2,3 The heats of formation deviate from the values predicted by the quasichemical theory above about 30 at. pct Cd. This deviation has been attributed to electronic effects at the Brillouin zone boundaries.2 The heats of formation of Ag-Cd alloys are essentially the same at 308", 723", and 800°K; consequently the temperature dependence of the heat of formation d?H/dT = ?Cp is vanishingly small, although from the exothermic heats of formation a negative value would have been expected. In the investigation reported here the heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of 1 solid solution have been measured by tin solution calorimetry. The results are analyzed in terms of the quasichemical theory and the dependence of the heats of formation on temperature is discussed. The relative partial enthalpies per gram-atom of silver in tin at 541" and cadmium in tin at 532" and 541°K were obtained in the course of this investigation. The values of the temperature dependence of the relative partial enthalpies per gram-atom of silver in tin derived from the data reported by various investigators2,4-9 are contradictory. The literature contains only a value for 517°K of the relative partial enthalpy per gram-atom of solid cadmium in tin.2 EXPERIMENTAL PROCEDURES Samples of Ag-Cd solid solutions were prepared by melting weighed amounts of silver (99.99 pct pure) and cadmium (99.95 pct pure) in graphite crucibles under a flux of molten potassium chloride.10 The solidified ingots were sealed in evacuated Vycor tubes and annealed at 775°K for 10 days. The ingots were swaged and drawn into wires. The wires, sealed in evacuated Pyrex tubes, were held at 725°K for 5 hr and cooled to 365°K at an average rate of 2.5ºK per hr, followed by furnace cooling to room temperature. Chemical analysis of samples taken from different parts of each ingot gave no indication of segregation. Metallographic examination showed the samples to be homogeneous. Samples of the solid solutions or of the component elements were added to tin-rich baths in a calorimeter." At the start of a run the bath consisted of pure tin. Silver was used in the form of wire of 0.01-in. diam as supplied and cadmium in the form of lumps. Gold (99.999 pct pure) was added with the samples in order to reduce the endothermic heat effect of additions of Ag-Cd solid solutions. Samples of only one composition were added in a run and the ratio of the weight of alloy to that of gold was the same in all additions of a given run. In each run several calibrating additions of tin were made from 273°K. The heat contents of tin were calculated from the following equation, which is based on published data:12 (HTºK- H279º) = 6.70 T - 72,300/T + 20 cal/gram-atom; 505°K < T < 650°K The heat effect of each addition was plotted against the average of the sum of the atom fractions of solutes in the solution before and after that addition. The total concentration of solutes at the end of a run was less than 2 at. pct. In this range the heat effect was a linear function of the atom fraction of the solutes. The heat effect at infinite dilution and the composition dependence of the heat effect were obtained from the plots. RESULTS AND DISCUSSION Evaluation of Data. The linear dependence on composition of the heat effects of additions suggests that in the dilute range the enthalpy interaction coefficients other than the first-order coefficients of silver, cadmium, and gold are negligible, as shown in a concurrent publication.13 The heat effects at infinite dilution and the values of the composition dependence of the heat effects are listed in Table I.

Jan 1, 1970