Search Documents

By John M. Hartman

TWO systems are used for heating air in blast-furnace operations: I. The double surface system, in which a cast-iron pipe is heated on the outer surface, and, at the same time, heats the blast from its inner surface. This is simple in operation and gives a continuous effect, but is limited by 1100" F. as a maximum temperature of the blast. 11. The single surface system, by which large surfaces of fire-brick are heated, and air passed over the heated surface, absorbing the heat and carrying it on to the furnace. This system is more comylex than the double surface, as it invoives the reversing of the air and gas every hour and a half. The single surface system has two advantages: 1. The blast can be heated to a temperature of 1800° F. 2. The stoves are indestructible. From recent experience it has been found that 1300" F. to 1400' F. is the best average temperature for economy of coal for safe working. This is equivalent to a saving of 11/2 to 2 cwt. of coal per ton of iron over the extreme limit of cast-iron stoves. Independently of this, it is a strong point in favor of this system that the blast can be raised to a temperature of 1800° F. within an hour when the hearth is getting cold. All furnacemen know the ralue of a hot hearth for quality and quantity of iron. Cooling of a hearth occurs from leaky tuyeres, scaffolds, or heavy burden. When there is not sufficient coal at the tuyeres to seize on the oxygen of the entering air and convert it at once to carbonic oxide, there will not be enough heat to liquefy the cinder. Black cinder and poor iron are the results. The remedy is additional heat from the blast. If the stoves will give 1800" in place of 1100°, it is obvions that the furnaces will get around sooner, and without waiting for a change of burden at the tunnel head to bring extra coal to the hearth. The heat absorption caused by a leaky tuyere will chill the hearth and drive the zone of fusion higher up in the furnace. This loss must be supplied, and the calorics lost to the hearth must be regained before good iron can be made. Take another case: A furnace carefully burdened on No. 1 iron, during a spell of damp weather, goes on to No. 2 or No. 3. Heat is lost to the furnace through absorption by the moisture, and less burden must be carried in order to get back on No. 1. When the

Jan 1, 1879

By D. W. Loucks

There is plenty of evidence to indi-cate that at least one of man's chief interests in life is to make himself as comfortable as possible. If you doubt this, just watch the fellow next to you for the next half hour trying to find the most comfortable position that a hard chair has to offer. Comfort, however, does not always mean an easy chair. To some, it may mean a wealth of money; to another, freedom from worry. But to most of us, it means first of all a comfortable atmosphere in which to live, and to a great many of us it probably also means freedom from that annoying task of firing the furnace. Today more than ever before. automatic heat is one improvement that is placed high on everyone's list. Perhaps this is because automatic heating is becoming relatively cheaper. Perhaps it is because of a good publicity campaign on the part of the oil and gas men or maybe it is just that we are getting lazier day by day. At any rate, almost every issue of Better Homes and Gardens, House Beautiful, or your other favorite home magazine carries an article extolling the virtues of this or that automatic heating system. If I were to ask you to name the first thing that came to your mind when I said automatic heat, you would prob-ably say either gas furnace or oil burner. Or if you had just been studying heating systems, you might possibly say heat pump. But chances are you would not mention anything about coal, and yet coal is the most common source of the greatest automatic heat of them all. I say this because coal is the fuel used almost universally by the district heating industry in producing and delivering to certain heavily populated areas heat ready to use at the touch of a valve or the click of a thermostat. Although the industry is over a half century old, it has not experienced the widespread development of other utility industries because of certain limitations which I believe you will realize from the next few minutes discussion. District Heating Operations We may define district heating as any operation where two or more buildings are heated from a central heating plant. The method of heat transfer may be hot water or in some cases warm air, but generally the medium of heat transfer is steam. So universally is steam used that the industry is frequently referred to as the district steam industry. The Allegheny County Steam Heating Co. which operates the district heating system in downtown Pittsburgh is a subsidiary of the Du-quesne Light Co. Although organized in 1912 primarily as a means of securing the electric load of downtown buildings, the service has now become so valuable and so popular that it is no longer considered a necessary adjunct to the electric business but rather a separate business standing on its own feet. Fig 1 shows the layout of the plants and distribution system of downtown Pittsburgh. Two generating plants, one known as the Stanwix and the other as Twelfth Street, supply the area. Each has two boilers with capacity totaling 1,350,000 lb per hour. The Stanwix Plant is supplied coal by truck. The coal is pulverized at the plant and burned as powdered fuel. Coal is supplied to the Twelfth Street Plant also by truck but the boilers arc stoker fired. Over 1 1/2 miles of tunnel house a portion of our main lines, but it requires over twelve miles of pipeline, ranging in size from 32 down to 1 in. in diameter, to supply all our customers. The distribution system consists of two systems in a sense, one high and one low pressure with certain interconnections between the two. Our high pressure system supplies steam up to 125 Ib to some but not all customers, while the low pressure system operates in the range of 10 to 20 psi. Note that the two plants are tied together through large steam mains and that the system to some extent is a loop system, making it possible to have a portion of the line shut, down without interrupting service to any customer. Fig 2 conveys a picture of the extent to which steam service is used in the downtown triangle. The black area indicates the buildings which now use district steam. The dotted area indi-

Jan 1, 1950

By E. C. Harder, E. W. Greig

Bauxite is known mainly as the ore from which aluminum is smelted but it has large use also in the manufacture of artificial abrasives and in the production of a number of useful chemicals as well as of aluminous cement "ciment fondu." An important and growing use is in the manufacture of refractory products. Composition Dana and earlier mineralogists gave the mineral formula of bauxite as A1203.21120 and the composition as A1202, 73.9 pct; H2O, 26.1 pct. A specific mineral of this composition has, however, never been identified by either microscopic, chemical or X ray examination, and therefore it is concluded that bauxite is a rock consisting of one or more aluminum minerals together with impurities. The term is now used synonymously with aluminum ore and it embraces gibbsite (hydrargillite or alpha trihydrate), A1203. 3H20 (A1203, 65.4 pct; H2O, 34.6 pct); boehmite (alpha monohydrate), A1203•H20 (A1202, 85 pct; H2O, 15 pct) ; diaspore (beta monohydrate), A1203•H20 (A1203, 85 pct; H2O, 15 pct), and mixtures in various proportions of any two of them. Bauxite of the Mediterranean region in Europe is predominantly boehmite, as in France and Istria, subordinately a mixture of gibbsite and boehmite, as in Dalmatia, or of boehmite (or gibbsite) and diaspore, as in Greece. The bauxite of North and South America, tropical Africa, Asia, and Australasia consists largely of gibbsite, but boehmite in appreciable amount occurs in many places. Corundum (A1202) is not included un¬der bauxite, although gradations from bauxite to emery or corundum exist. All bauxite, irrespective of the aluminum minerals composing it, contains certain impurities in variable amount, including silica in the form of clay minerals (kaolinite, halloy site, and others) or quartz, iron oxide (as hematite or goethite), titania (as leucoxene or rutile), iron sulfide (as pyrite or marcasite), iron carbonate (siderite), and calcium carbonate (as calcite); the last three mentioned in minor amount and of local occurrence only. Bauxite belongs to a group of partly consolidated materials called laterites, formed by surface weathering. This group includes also impure siliceous, ferruginous, and phosphatic bauxite and siliceous and aluminous iron ores and manganese ores and nickel and chrome laterites. Phosphorus and manganese minerals locally form important impurities in bauxite deposits. Properties Gibbsite is white or light shades of gray, cream or pink. Its hardness is 2.5 to 3.5; specific gravity, 2.3 to 2.4; crystal system, monoclinic, crystals tabular parallel to 001, often fibrous, concretionary, stalactitic; luster, vitreous to pearly; generally translucent; cleavage, parallel to 001; disassociation temperature, approximately 300°C. Boehmite, a relatively new and important mineral described by J. Boehm15 in 1925, confirmed and named by J. de Lapparen64 in 1930, has some properties not yet definitely determined. It occurs in grayish, brownish, and reddish shades. Its hardness is between that of gibbsite and diaspore; specific gravity, 3.01 to

Jan 1, 1960

By Clarence Zener

Theoretical considerations by one of the authors have ledl to the prediction that the dynamic internal friction of annealed metals has a broad maximum at a certain grain size. This prediction they have verified2 for alpha brass. In the present paper the theory is extended to include the precise manner in which the internal friction varies with grain size on either side of the maximum. New experimental data are presented to test this extended theory. The physical basis for the type of internal friction that is being investigated lies in the interplay between stress and temperature. Just as local fluctuations in temperature give rise to local fluctuations in stress, so likewise fluctuations in stress give rise to fluctuations in temperature. But temperature gradients give rise to necessarily irreversible thermal currents, and hence to internal friction. The theory for this type of internal friction has been developed quantitatively,³ and has been experimentally verified,4,5 for the particularly simple case of the transverse thermal currents accompanying transverse vibrations. Of more fundamental importance are the intercrystalline thermal currents accompanying all types of vibration. The variation in stress across grain boundaries arises from the elastic anisotropy and at least partial random orientation of the individual crystallites. An exact quantitative treatment of the internal friction due to these thermal currents is of course out of the question. However, much information can be obtained from general arguments.1,6 Thus when the frequency of vibration f is low, or when the grain size d is small, adjacent grains remain nearly in thermal equilibrium, and vibration proceeds isothermally with little internal friction. Again, when the frequency is high, or the grain size large, the heat flow per cycle is small, the vibration proceeds adiabatically with little internal friction. The internal friction will become a maximum in the transition region. The degree of adiabatic-

Jan 1, 1940

By Clarence Zener

Theoretical considerations by one of the authors have ledl to the prediction that the dynamic internal friction of annealed metals has a broad maximum at a certain grain size. This prediction they have verified2 for alpha brass. In the present paper the theory is extended to include the precise manner in which the internal friction varies with grain size on either side of the maximum. New experimental data are presented to test this extended theory. The physical basis for the type of internal friction that is being investigated lies in the interplay between stress and temperature. Just as local fluctuations in temperature give rise to local fluctuations in stress, so likewise fluctuations in stress give rise to fluctuations in temperature. But temperature gradients give rise to necessarily irreversible thermal currents, and hence to internal friction. The theory for this type of internal friction has been developed quantitatively,³ and has been experimentally verified,4,5 for the particularly simple case of the transverse thermal currents accompanying transverse vibrations. Of more fundamental importance are the intercrystalline thermal currents accompanying all types of vibration. The variation in stress across grain boundaries arises from the elastic anisotropy and at least partial random orientation of the individual crystallites. An exact quantitative treatment of the internal friction due to these thermal currents is of course out of the question. However, much information can be obtained from general arguments.1,6 Thus when the frequency of vibration f is low, or when the grain size d is small, adjacent grains remain nearly in thermal equilibrium, and vibration proceeds isothermally with little internal friction. Again, when the frequency is high, or the grain size large, the heat flow per cycle is small, the vibration proceeds adiabatically with little internal friction. The internal friction will become a maximum in the transition region. The degree of adiabatic-

Jan 1, 1940

By Ripu Daman Lama

The size of coal pillars in mines until recently has been determined by experience without being based upon scientific investigations. As a consequence, the size of pillars had invariably been larger than could be accounted for because of the number of unknown factors involved which influence the strength, dictating the use of large safety factors. With the mining going deeper, the size of the pillars greatly increases and sometimes a considerable portion of the mineral property are blocked in the mine pillars required to support the superincumbent strata. With the advances in the field of Rock Mechanics, attention of mine planning engineers has been focused upon the design of mine pillars for safe and efficient working as well as decrease losses of coal. The problem involves the study of three factors: (1) Presence of stresses in the area and their distribution on pillars in the course of extraction. (2) The influence of external factors on the strength of coal. (3) The inherent mechanical properties of coal. These aspects have been studied by a large number of investigators, the first by in-situ stress measurements and photoelastic studies and the second and third aspect by studies conducted in the laboratory on small size specimens (Bunting, 1911; Evens & Pomeroy, 1961; Gaddy, 1956; Greenland et al, 1941; Steart 1954). The size of the specimens tested in the laboratory has been limited to a few inches and the results obtained have been extrapolated by large factors, sometimes several hundred times the largest specimen tested. In these tests much consideration has not been given to

Jan 1, 1971

HENRY FAY, Cambridge, Mass. (written discussion *).-Mr. Rawdon has made a distinct contribution to our knowledge of wrought iron, and .perhaps of steel. It will undoubtedly lead to more careful scrutiny of high-phosphorus steels, with perhaps important results. In view of his results, it would seem to be unprofitable to push further any propaganda on the use of higher-phosphorus low-carbon steels until further information is available. As is well known, and as Mr. Rawdon clearly shows, the process of solidification is a selective one, and there is abundant opportunity for those portions of the melt last to solidify to become rich in phosphorus, and the diffusion of this phosphorus-rich area is slow. Hot work does not help the situation appreciably and only serves to concentrate the low-melting material. It is undoubtedly true, as some writers have recently claimed, that the specifications for steels as they. now exist eliminate some perfectly good material. Higher phosphorus in steel may be perfectly safe provided all of the phosphide is completely and uniformly, diffused in the solid solution. If, on the contrary, it is not evenly diffused, and there is a reasonable chance for it not to be, it makes the steel unsafe. Until our knowledge: of the rate of diffusion of phosphorus in steel, and the effect of other elements upon the rate, is more complete, it seems to me unwise, in view of Mr. Rawdon's experiments, to listen to the recommendations for the use of higher-phosphorus steels.

Jan 1, 1918

By Peter J. Szabo

INTRODUCTION The time period from the detailed feasibility study to the post investment audity usually ranges from three to eight years depending upon the nature of the mining project considered. It is the only after the post investment audit that we know the adequacy of the assumptions made concerning operational risk assessment in the detailed feasibility or acquisition economics. The post investment audit results from numerous mining projects can best be described by a verse by John Greenleaf Whittier's Maaud Muller. It reads "For all sad words of tongue or pen the saddest are these 'It might have been!"' Dissecting the negative results of numerous mining projects we find faulty assumptions concerning markets, geology, capital investment and operational risk assessment. Although in hindsight many of these assumptions could have been considered impossible or impracticle to have forecast with any degree of certainty, we find that refined assumptions concerning operational risk assessment could have been made with only a modicum of additional "Due Diligence". Anyone who invests in a mining property should employ a much higher discount rate of future cash flow, (usually in the minimum range of 25%-30%), than he would expect from such safe investments as Treasury Bills or high grade Utility Bonds. The nature of this steep discount translates to a large uncertainty concerning the timing and actualization of assumptions contained in the detailed feasibility study. We must remember that when a project gets beyond 20 years, any contribution to the value of the project of cash flow is minimal due to the nature of the discounting process. Thus for each full or partial day lost in the development or early operation stage of a project, the financial impact will be greater than similar lost days later on in the project. Adequate operational risk assissment is particularly critical when bidding on competitive tenders for coal deposists in remote locations such as the Bowen Basin in Queensland, Australia. Because of the market attractiveness of these coal deposits for supplying end users in the Far East, Middle East and Europe, state governments require competitive tender biddings via the Authority to Prospect process. Front end bonuses and super royalty payments must be commited before the actual mining conditions are known. Time to submit firm offers from the actual request for proposal vary from 90 to 120 days. Thus any operational risk assessment must be detailed, realistic and reflective of the actual project. When one searches the literature, one finds limited qualitative data on operational risk assessment in valuation papers. Usually this facet of valuation takes a secondary role to such areas as reserves, markets, and environmental considerations. When one comes to the question of operational risk assessment more often than not one finds the use of "rules-of-thumb", such as tons per man shift, average production, average seam height, etc., are used to forecast results on which banks and other financial institutions are required to make investment decisions. Because of the extremely competitive environment of the 1970's and 1980's numerous financial institutions approved loans without adequate "Due Diligence", and are currently paying a steep price in terms of non performing loans and charge offs. One must always remember that each operation is unique with its own characteristic

Jan 1, 1985

By Gordon H. Geiger, John M. Svoboda

One mechanism of metal penetration into mold aggregates by cast steels is vapor state mass transport. In order to further understand and quantify this mechanism, the steady-state diffusion of metallic vapors was studied at 1250" to 1600°C in controlled oxygen pressure atmospheres by measuring the weight loss from a metal bath whose vapors were allowed to diffuse through a porous aggregate compact held at constant temperature. Mass transport rates substantially greater than those predicted from the assumption that the vaporizing species was the elemental metal vapor were observed. Vaporization rates were found to increase with an increase in the oxygen partial pressure in the gas atmosphere with maximum vaporization occurring at oxygen partial pressures just below those in equilibrium with a liquid oxide layer at the given temperature. When the liquid oxide layer was present, no vaporization was observed. Metal carbonyls were ruled out as the vapor species involved because of their thermodynamic properties. The species with the enhanced volatility were deduced to be gaseous metal-oxygen molecules, probably the polynuclear oxides (FeO)2 and (Mn0)2. Diffusion followed the ordinary diffusion mode, and Knudsen diffusion is not important in normal foundry molds. The interdiffusivities of the metallic vapors and the mold atmosphere, through the porous aggregates, were measured. The effective interdif-fusivity of the vapor species and mold atmosphere through the aggregate may be expressed as follows: Deff,12 - — where E is the void fraction of the aggregate and 7 is the "tortuosity factor". Aggregate material had no effect on diffusion rates, and the only relevant parameter was the void fraction. Values for 7 ranged from 3 to 6 for normal foundry aggregates with 4 being considered a good representative value. An area of interest in high-temperature metallurgical processes which has received little attention in the past is the diffusion of metal vapor species in porous aggregates. Research into the metal penetration phenomenon' in foundry molds has shown that a major penetration mechanism is the vapor transport of metallic species into the porous foundry sand molds, followed by condensation of metallic films on the sand grains. Considerable study of the vaporization of metallic species has been reported in the literature, and the vapor transport properties of many metallic species have been determined.2'3 Many instances have been observed where the vaporization behavior could only be explained by the existence of a metallic species with a vapor pressure greater than the elemental metallic species. These species were identified or, in some cases, presumed to be carbonyls,4,5 hydroxides,6-9 or vaporous oxides.10-16 The diffusion of gases through porous aggregates has received considerable attention in the literature pertaining to catalysis, although primarily at low temperature, and more recently in the literature concerned with ore reduction.17-22 The following experiments were devised and carried out in order to determine the nature of the metallic species involved in the metal penetration phenomenon, and the effective diffusivities involved. EXPERIMENTAL APPROACH Steady-state diffusion was selected for experimental convenience. The experimental systems used, shown in Figs. 1 and 2, consisted of a porous aggregate specimen contained in an impermeable alumina tube held above, and just separate from a metal bath. The entire system was held at constant temperature and pressure in a furnace with a controlled oxygen partial pressure atmosphere. After a brief period of nonsteady state behavior, a steady flux of metal vapor through the porous aggregate will develop due to the concentration gradient of metallic vapor in the gas phase. The flux of metallic vapor from pressure may be neglected because there is no pressure gradient. There is no flux from convection because there is no net flow of gas within the metal-aggregate system, and thermal diffusion is negligible compared to the flux from ordinary diffusion. If the material being studied is allowed to vaporize until steady-state behavior is attained, the experimental results may be analyzed using Fick's First Law.

Jan 1, 1970

By A. Paul Bond

Two series of 17pct Cr iron-base alloys with small, controlled amounts of carbon and nitrogen were vacuum-melted in an effort to detertmine the meclz-uniswls of inter granulur corrosion in ferritic stain-less steels. An alloy containing 0.0095 pct N aid 0.002 pct C was very resistant to intergranular corrosion, even after sensitizing heat treatments at 1700" to 2100o F. However, alloys containing more than 0.022 pct Ni and more than 0.012 pct C were quite susceptible to intergranular corrosion after sensitizing heat treatments at temperatures higher than 1700°F. This corrosion was observed after the usual exposure tests and after potentiostatic polarization tests. Electronmicroscopic examination of the alloys susceptible to intergranular corvosion revealed a small grain boundary precipitate; this precipitate was absent in the alloys not susceptible to such corrosion. Thc electronmicrographs indicate that intergranu1ar corrosion of ferritic stainless steels is caused by the depletion of chromium in areas adjacent to precipi-tates of chromium carbide or chromium nitride. It also seems likely that the precipitates themselves are attacked at highly oxidizing potentials. Confirma-tion of the proposed mechanisms was obtained in tests on air-melted ferritic stainless steels containing titanium. The titanium additions greatly reduced susceptibility to intergranular corrosion at moderately oxidizing potentials but had no beneficial effect at highly oxidizing potentials. A major obstacle to the use of ferritic stainless steel has been their susceptibility to intergranular corrosion after welding or improper heat treatment. It appears that sensitization of ferritic stainless steel occurs under a wider range of conditions than for austenitic steels. In addition, a greater number of environments lead to damaging intergranular corrosion of sensitized ferritic stainless steels than to sensitized austenitic steels. The chromium depletion theory of intergranular corrosion is widely accepted for austenitic stainless steels'" although there: are some objections.3 On the other hand, several alternative mechanisms proposed for ferritic stainless steels include precipitation of easily corroded iron carbides at grain boundaries,' grain boundary precipitates that strain the metal lat-tice,5 and the formation of austenite at the grain bound-arie.6 The application of the chromium depletion theory to ferritic stainless steels has been discussed extensively by Baumel.7 The present investigation was undertaken to determine which of the proposed mechanisms can be sub- A PAUL BOND IS Research Group Leader, Climax Molybdenum Co of Michigan, Ann Arbor, Mich. stantiated with experimental data obtained on ferritic stainless steels. High-purity 17 pct Cr alloys containing small controlled additions of carbon or nitrogen were therefore prepared, and then examined electro-chemically and metallographically. EXPERIMENTAL PROCEDURES Materials. Two series of experimental alloys were prepared from electrolytic iron and low-carbon ferro-chromium using the split-heat technique. In this technique, the base composition is melted, and part of the melt is poured off to produce an ingot. To the balance of the melt, the required addition is made and the next ingot cast. This process is repeated until a series of the desired compositions is cast. By this procedure the impurity levels are essentially constant within each series. All the alloys in the carbon-containing series were melted and cast in vacuum. The base composition in the nitrogen series was melted and cast in vacuum; subsequent ingots in the series were melted with additions of high-nitrogen ferrochromium, and cast under argon at a pressure of 0.5 atmosphere. Two additional alloys were produced starting with normal purity materials. They were induction-melted while protected by an argon blanket and cast in air. Table I gives the composition of the alloys. The 2-in.-diam ingots produced were hot-forged and hot-rolled to a thickness of 0.3 in. and then cold-rolled to 0.15 in. All specimens were annealed at 1450°F for 1 hr. The indicated sensitizing heat treat-s s ments were performed on annealed material. All heat treatments were followed by a water quench. Specimen Preparation. For the 65 pct nitric acid test, 1 by 2 by 0.14-in. specimens were wet-surface ground to remove surface irregularities and polished through 3/0 dry metallographic paper. For the modified Strauss test, $ by 3 by 0.14-in. specinlens were similarly prepared. Immediately prior to testing, the Table I. Compositions of the Alloys Composition, pct Alloy Cr hio C N 270A 16.76 0.0021 0.0095 270B 16.74 0.0025 0.022 270C 16.87 0.0031 0.032 270D 16.71 0.0044 0.057 271A 16.81 0.012 0.0089 27 IB 16.76 0.018 0.0089 271C 16.69 0.027 0.0085 271D 16.81 0.061 0.0O71 4073' 18.45 1.97 0.034 0.045 4075† 18.5 2.0 0.03 0.03

Jan 1, 1970

By Frederick N. Rhines, Robert F. Mehl

Relatively few data have been collected on the rates of diffusion in ternary solid solution systems. In general it does not seem worth while to gather extensive data for such systems until the factors that determine the rates of diffusion in binary systems are better understood. But the rates of diffusion in a ternary system of limited solid solubility, in which the terminal solid solution is in equilibrium with an intermediate phase and may thus be represented as a quasibinary system, represents a case of special interest. In this case, where by reason of the association of the two solute metals in an intermediate phase a special attraction of the two solute atoms may be safely assumed, some interaction of these atoms during simultaneous diffusion in the solvent lattice might be expected. It has frequently been proposed that molecular solid solutions exist in quasibinary and in other ternary (and binary) solid solutions. There is no direct evidence for such solid solutions; arguments based upon the supposed anomaly in certain physical properties1 are hardly important; unexpected density relationships have proved deceptive;2 suggestions of molecular solid solutions have been made on the basis of solution laws in their application to certain systems, but without result;3 attempts to find lattice parameters in the solid solution Al-MgZnz, which cannot be calculated from the separate effects of magnesium and zinc and might therefore be taken as evidence for a molecular aggregation, have given negative results.* Fundamentally, methods for the determination of the state of molecular aggregation in solution depend upon the kinetic behavior of the particles constituting the system. If it could be shown that the two solutes in a quasibinary ternary system diffuse in molecular proportions, despite a radical difference in the separate rates of diffusion of each solute when diffusing alone in the solvent lattice, some basis for the concept of molecular solid solution would be afforded. Freche5 examined the rates of

Jan 1, 1940

By Frederick N. Rhines, Robert F. Mehl

Relatively few data have been collected on the rates of diffusion in ternary solid solution systems. In general it does not seem worth while to gather extensive data for such systems until the factors that determine the rates of diffusion in binary systems are better understood. But the rates of diffusion in a ternary system of limited solid solubility, in which the terminal solid solution is in equilibrium with an intermediate phase and may thus be represented as a quasibinary system, represents a case of special interest. In this case, where by reason of the association of the two solute metals in an intermediate phase a special attraction of the two solute atoms may be safely assumed, some interaction of these atoms during simultaneous diffusion in the solvent lattice might be expected. It has frequently been proposed that molecular solid solutions exist in quasibinary and in other ternary (and binary) solid solutions. There is no direct evidence for such solid solutions; arguments based upon the supposed anomaly in certain physical properties1 are hardly important; unexpected density relationships have proved deceptive;2 suggestions of molecular solid solutions have been made on the basis of solution laws in their application to certain systems, but without result;3 attempts to find lattice parameters in the solid solution Al-MgZnz, which cannot be calculated from the separate effects of magnesium and zinc and might therefore be taken as evidence for a molecular aggregation, have given negative results.* Fundamentally, methods for the determination of the state of molecular aggregation in solution depend upon the kinetic behavior of the particles constituting the system. If it could be shown that the two solutes in a quasibinary ternary system diffuse in molecular proportions, despite a radical difference in the separate rates of diffusion of each solute when diffusing alone in the solvent lattice, some basis for the concept of molecular solid solution would be afforded. Freche5 examined the rates of

Jan 1, 1940

By T. A. Read, H. K. Birnbaum

Deformation of AuCd alloys having the 8 (orthorhombic) and (3" (tetragonal) structures occurs by the stress induced motion of twin boutdaries. A restoring force acts on displaced twin boutdaries as a result of internal energy increases in the volume through which the boundaries are displaced. The phenomonology of the twin boundary motion is described and a mechanism for twin boundary motion and the restoring force is proposed. A time-dependent stabilization behavior of the twin boundaries, which is observed after the twins are formed by the diffusionless phase transformations, is described. THE AuCd 8 phase (ordered bcc structure) exhibits a transformation to a phase having an orthorhombic structure, 8' (space group D'), for compositions in the vicinity of 47.5 at. pct Cd and to a phase having a tetragonal structure, 8" (point group 4/m, m,m), for compositions in the vicinity 50.0 at. pct Cd. Both transformations are diffusionless, occur on cooling at 60" and 30OC, respectively, and are crystallo-graphically reversible.' They are accompanied by an inhomogeneous deformation which was observed to be twinning in the low-temperature phase. 3'4 The transformations may occur by a "single interface" or by "multiple interfaces."5'6 In the "single interface" transformation, the twinned product phase consisted of two twin orientations as shown in Fig. 1. In the multiple interface transformation the product phase contained "domains" each of which contained two twin orientations, Fig. 2. Deformation of specimens containing transformation twins was achieved by motion of the twin boundaries. Releasing the applied stress resulted in the displaced twin boundaries returning towards their initial positions. This "pseudo-elastic" behavior of the boundaries varied with time after the formation of the twin boundaries by the transformation.

Jan 1, 1961

By Rudolf Kudlich

THE problem of eliminating the hazards of hoisting in mines has been with us since the industry passed its earliest stages, when coal and ore could be won from surface working and tunnels. At first, safety devices were introduced as means of decreasing the amount of labor necessary, to produce the mineral, or to increase the amount that could be obtained from a certain opening. For example, crude, ladders replaced winding footpaths or steps cut into the walls of the pit or shaft, decreasing the distance it was necessary to carry the product to the surface and eliminating, to some extent, the hazard introduced by the precarious footing afforded by such paths and steps. Later, instead of being carried from the pit on the backs of men, the product was hoisted in buckets or baskets on a rope passing over a pulley or around a windlass. Thus the capacity of the pit was considerably increased, and the hazard due to making many trips up and down the shaft was eliminated. From such beginnings accident prevention in mine hoisting advanced with the importance of the industry, until at present hoisting compares favorably with other branches of the mining industry with reference to safe practices. As in the other branches, this progress has been accomplished along two general lines-by legislation, rules, and education, and by the installation of safety devices. Though due credit must be given the former, it is not so satisfactory as the latter. Legislation, to be effective, requires a policing and inspection system to guarantee enforcement, such as we cannot hope to inaugurate. Rules may be satisfactory so long as the employer controls the labor market, and dismissal or some other form of discipline is an effective means of insuring obedience to the rules; but where labor demand is in excess of the supply, or where labor organizations are in control, such measures are not effective. An educational campaign will draw attention to hazards and may awaken a desire to avoid accidents by exercising the proper care.

Jan 2, 1922

By D. J. McAdam

As shown in three recent papers by the author,6,7,8 in two papers by McAdam and Mebs,9,10 and in a paper by McAdam, Mebs, and Geil,11 the technical cohesive strength of a metal, in any particular state as regards mechanical treatment and heat-treatment, cannot be represented by a single stress value, but must be represented by a diagram with the principal stresses? as coordinates. Each point on the boundary of such a diagram represents a technical cohesion limit. The technical cohesive strength thus comprises an infinite number of technical cohesion limits, each representing fracture under a specific stress combination. Moreover, neither the yield strengths nor the ultimate strength can be represented completely by a single stress value, but must be represented by a diagram with the principal stresses as coordinates. All combinations of the principal stresses may be classified in three groups as illustrated by Fig. I. Fig. Ia shows three typical stress combinations with no two principal stresses equal. The magnitude of each principal stress is indicated qualitatively by the length of the arrow. Arrows pointing away from the cube indicate tensile stresses; arrows pointing toward the cube indicate compressive stresses. Typical stress combinations with two principal stresses equal are illustrated in Figs. Ib and Ic. Such stress combinations would be produced by subjecting a cylinder to combinations of uniform axial and radial stresses. The uniform radial stress may be resolved into two equal principal stresses, with the mutually perpendicular directions rotatable around the axis of the cylinder. Fig. Ib shows stress combinations with S2 equal to Sa. The greatest principal stress is in the axial direction, and the stress combination tends to cause either absolute or relative increase in length.* Fig. Ia shows stress combinations with Ss equal to Sl. The greatest principal stress is in the radial direction, and the combination tends to cause either absolute or relative decrease in length. The complete representation of either technical cohesive strength, yield strength, or ultimate strength generally requires a three-dimensional diagram. When two of the principal stresses are kept equal, however, the strength of a metal may be represented by a two-dimensional diagram with the coordinates representing the axial and radial stresses.6-11 In this paper, attention will be confined almost entirely to stress combinations with two of the prin-

Jan 1, 1944

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society but the name has now been changed to one which more nearly reflects the real function of the corporation. It holds title to the Engineering Societies Building and to various funds placed in its charge and is managed by a Board of Trustees of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical Engineers, American Society of Mechanical Engineers, American Institute of Electrical Engineers and American Society of Civil Engineers, which own equal and undivided interests in the property. The land and building cost two million dollars. The interest of each of the Founders societies, aside from especial trust funds, is now valued at $493,352. The A. I. M. E. trustees are Arthur S. Dwight, J. V. N. Derr and George D. Barron. The President of the Board is Francis Lee Stuart and the Secretary, Alfred D. Flinn.

Jan 1, 1923

By D. Harrington

During the past few years, there has been a trend toward the use of rock-dusting, rather than relying on humidifying, or the use of water, to limit or prevent explosions in the coal mines of the United States. This is partly because British coal mines have adopted rock-dusting and, at least in a sense, have condemned the use of water. Moreover, during the past few years, particularly in the latter part of 1922 and in 1923 and 1924, several explosions with heavy loss of life occurred in coal mines of the United States that were known to have more or less extended sprinkling, or humidifying, systems. The sentiment created by these disasters quickly caused a distrust of explosion-prevention methods requiring use of water and simultaneously caused more or less of a stampede into rock-dusting. Much of the wholesale condemnation of watering methods was without adequate knowledge, or at least without adequate consideration, of local conditions in each case, and rock-dusting was adopted largely without sufficient knowledge of how to rock dust safely or correctly. However, mines that had been using watering methods and had suffered these recent serious disasters (notably Dolomite, Dawson, and Castle Gate) instead of abandoning the use of water when operations were resumed after the disaster, greatly extended their watering systems. At the same time they took other precautions as to electricity, ventilation, blasting, etc., and supplemented the watering system with rock-dusting where the latter was likely to be the more effective. The trend toward rock-dusting during the past year or two (succeeding the recent mine disasters) is very similar to the rapid movement toward watering, or humidifying, methods, about 1910 to 1912, after a series of disastrous mine explosions. The Phelps-Dodge Corpn., which operates a large property at Daw-son, N. M., after an explosion in its No. 1 mine in February, 1923, decided that it is dangerous to have all its "explosion-prevention eggs in one basket" and so adopted what may now be termed the Western coalmine explosion-prevention system, in which both rock-dusting and watering are used, supplemented by other up-to-date mining methods and practices; such as exclusive use of modern electric safety lamps, with magnetically locked flame safety lamps for testing purposes; use of

Jan 1, 1925

By ALBERT P. J. BORDEAUX

THIS paper briefly describes the general outline of cyaniding silver-ores in Mexico, with special reference to personal experiments made in the Temascaltepec district. The most important papers on the subject deal with cyaniding gold-silver-ores, the gold predominating in value, so that the treatment is nearly the same as for gold-ores, the losses of silver being considered of little importance. I describe here the treatment of silver-gold-ores containing very little gold, which is more general in Mexico than elsewhere. The cyanide treatment, which was so successfully applied to gold-ores, did not succeed immediately with silver-ores on account of their varying composition. Gold occurs in nature usually in the native state, while silver occurs generally in combination with sulphur (argentite), and various combinations of sulphur, antimony, and arsenic. In former times there was a complete difference in the treatment of gold-ores and silver-ores. Amalgamation, which was successful with gold-ores, was generally inadequate with silver-ores. The usual treatment in Mexico for silver was the patio process, the theory of which was satisfactorily explained only quite recently by Mr. Ortega and others. GENERAL OUTLINE OP THE CYANIDE TREATMENT. The general tendency of the present practice is to slime the silver-ore as much as possible, and in order to obtain a higher efficiency, with less loss of cyanide, and greater speed, the following lines are observed 1. Crushing by stamps with 30- or 40-mesh screens, then crushing by Huntington or Chilean mills, through 60- or 80-mesh screens. 2. Concentration upon vanners.

Jan 1, 1910

By W. J. Romanow

RECENT papers by Williams, Sherwood, and Boothby,1 Seybolt et al.2 Heikes; and Roberts4 attest to the increasing importance of the hexagonal ferromagnetic compound MnBi. Since the magnetic properties of MnBi crystals are highly anisotropic, it is useful and necessary to have appropriate aids for determining their orientations—a (00.1) standard stereographic projection and a corresponding table of crystallographic angles for this structure. The tables of crystallographic angles for the hexagonal system available in the literature5 are computed for c/a ratios greater than that of MnBi and cannot satisfactorily be used to find the crystallographic angles of MnBi. A table of angles between the crystallographic planes (HK.L) and (hk.1) was calculated for MnBi from the formula0 F=are cos Hh+Kk+ 1/2(Hk+hK) + 3/4 (a/c)2Ll/v(H2 + K2 + HK + 3/4 (a/c)2L2) (h2+ k2+hk + 3/4 (a/c)2l2) on an IBM Type 650 Magnetic Drum Data Processing machine. The lattice constants used are listed in Table I and are those determined by Willis and Rooksby7 at 20°C. More recently published values obtained by both X-ray and neutron diffraction"' show no difference from these significant to the calculation. From the crystallographic angles between the basal plane (00.1) and the general plane (hk.1) in Table I, an (00.1) standard stereographic projection was made for MnBi which is shown in Fig. 1. Acknowledgments The author wishes to thank R. G. Treuting and J. N. Hobstetter for their technical assistance, and Miss D. P. Booth for programing the IBM machine for the calculations. He appreciates the opportunity to read the paper of B. W. Roberts of General Electric Co. prior to its publication. References 1H. J. Williams, R. C. Sherwood, and 0. L. Boothby: Bulletin Amer. Physical Soc., 1956 vol. 1, p. 132. 2 A. U. Seybolt, H. Hangen, B. W. Roberts, and P. Yurcisin: AIME Trans., 1956, vol. 206, p. 605: Journal oF Metals, May 1956. 3R. R. Heikes: Physical Review, 1955, vol. 99, p. 446. .B. W. Roberts: A Neutron Diffraction Study of the Structures of Manganese B.W.Roberts:ANeutronDiffractionBismuthide, Physical. Review, 1956, vol. 104, p. 607. 5 A. Taylor and S. Leber: AIME Trans., 1954, vol. 200, p. 190; JouRNal of Metals February 1954. « C. S. Barrett: Structure of Metals, 2nd Ed., p. 635. McGraw-Hill Book Co. New York and London, 1952. 7B. T. M. Willis and H. P. Rooksby: Proceedings Physical Soc., London, 1954, vol. 67B, p. 290.

Jan 1, 1958

By AIME AIME

A PAPER prepared by James A. Adams, development engineer of the fitline & Smelter Supply Co., and presented at the last Annual Meeting of the A.I.M.E. in New York City, de- scribed a new automatic pulp density controller which has had a most favorable reception. Manual control has until now been the universal practice in spite of its shortcomings; samples of pulp for density determination were often improperly taken, and only at the operator's convenience, so that the trend in density changes was frequently missed, and the grinding circuit al- lowed to operate under something less than the most efficient conditions.

Jan 1, 1940