Search Documents

By B. C. Craft

Development and exploratory work in Mississippi during 1934 was rather active, resulting in the expansion of the proven area and the drilling of a number of important wildcat wells. Mississippi showed a decrease in drilling operations during 1934. There were 36 completions from 18 counties during this period compared with 58 completions from 22 counties during 1933. There was a considerable decrease in activity in the Jackson gas field in Hinds and Rankin counties with only 9 completions, resulting in 8 gas wells and 1 dry hole compared with 17 gas wells, 2 oil wells and 7 dry holes during 1933. Leasing and geophysical work was reported from several sections of Mississippi last year. Extensive exploration and drilling were carried on in Lamar, Hancock, Pearl River, Greene and Stone counties and on the flanks of the Jackson anticline. Exploration will be continued in these areas during 1935. Four important wildcats were completed during 1934, all of which were reported as being structurally high, but without having important shows of oil or gas. These tests were: Hix and Germany's, J. J. Newman Lumber Co. No. 1, sec. 21-4N.-15W., Lamar County, abandoned at 3520 it. in the Wilcox; United Gas Public Service Company's Davis No. 1, sec. 30-1N.-5W., Greene County, abandoned at 7439 ft.; Gulf Refining Company's May L. Williams No. 1, sec. 33-5S.-17W., Pearl River County, abandoned at 4800 ft.; and Clarke County Oil Company's S. B. Kirkland No. 1, sec. 10-2 N.-16E., abandoned at 4002 ft. in the Eutaw. Another interesting wildcat was Gulf Refining Company's Dantzler Lumber Co. No. 6, sec. 22-4S.-llW., Stone County, abandoned at 7700 ft. (according to reports below the Selma chalk). A total of 114 of the 132 gas wells completed in the Jackson gas field are still producing and have a combined open-flow capacity of 4,145,-696,000 cu. ft. Four of the abandoned gas producers were never connected to the lines. The open-flow capacity of three wells in the Amory field is approximately 1,000,000 cu. ft. Producing against a line pressure of 50 lb., the demand during December greatly exceeded the capacity.

Jan 1, 1935

By C. W. Spencer, J. Singer

A PARTIAL phase diagram for the As-Te system is given in Hansen.' The only compound reported is As2Te3, melting at 362°C. Stoichiometric quantities of reagent-grade elements were reacted in evacuated quartz and directionally cooled. The resulting ingot consisted of very thin threadlike crystals from which only very small single-crystal fragments were isolated. A powder diffraction diagram disclosed nonisomorphism with the analogous V-VI compounds insofar as these have been reported; Sb2S3, As2S3, Bi,S,, and Bi2Te3 data in the ASTM index of powder patterns, together with the single-crystal data on Sb2Se3,2 were used for the com- parison with the observed spacings. Single-crystal data confirmed the uniqueness of the As2Te3 structure. Single-crystal Weissenberg diagrams have so far yielded the following data: As2Te3 is monoclinic, space group C-m (OkO data still lacking), a = 14.4A, b = 4.05A, C = 9.92A, ß = 97". The cell volume is about 5802. The set of isomorphous ortho-rhombic cells of Sb2Se3, Sb2S3, and Bi2S, are apparently related to As,Te, in having one lattice constant close to 4.0 and with cell volumes as large as 540A8. Assuming Z = 4 for As2Te3 also, the density is calculated as 6.1 which agrees well with a roughly determined value of 6.0. A complete structure analysis is under way.

Jan 1, 1956

By AIME AIME

ON Thursday a most interesting symposium on "Gases in Metals" was held, with both morning and afternoon sessions. The morning was devoted principally to the considerations of the steel maker, the nonferrous field being taken up in the afternoon period. Dr. John Johnston, as chairman, introduced the subject with "A Short Analysis of the Gas-metal Problem and Its Practical Importance." He then introduced P. H. Brace who explained in considerable detail the various vacuum fusion and other methods in use at present, both here and abroad, in the study of "gases" in metals. He was fol¬lowed immediately by H. W. Graham on "The Effect of Oxygen in Steel." The papers elicited considerable discussion, the point being particularly noted by both Dr. Rawdon and Dr. Sauveur that a knowledge of "total oxygen" alone is not sufficient information for the metallurgist, distribution of oxygen being probably the more important. Dr. Johnston, in commenting on the lack of agreement among many of the methods now in use, such as the Ledebur and vacuum fusion, spoke of the contemplated plan of the Iron and Steel Division to have a number of standard samples analyzed by many laboratories by the various methods, the Bureau of Standards acting as a clearing house, so that more definite information may be obtained on the comparative accuracy of the method.

Jan 1, 1933

By AIME AIME

THANKS to the excellent preliminary work of: the Division officers and the local committee the fall meeting of the Coal Division at Bluefields was a brilliant success. West Virginia was at its best with its beautiful mountains, good roads and foliage, just beginning to turn to autumn colors. The meeting began on time and was kept on time throughout. The papers were-well prepared and, being on subjects of live interest, provoked 'lively discussion. One factor in bringing this about was that they were not too numerous and that with one exception copies had been submitted in advance a sufficient time to permit of them having been studied. The Friday morning session was presided over by John .J. Lincoln of the Crozier Coal and Coke Co. and president of the Pocahontas Coal Operators Association. After brief announcements by Thomas H. Clagett, chairman of the local committee, regarding plans for the two day's involved, and by Howard N. Eavenson, chairman of the Division, the reading of papers was taken up.

Jan 1, 1931

By J. S. Marsh

AN incomplete statistical analysis performed wearily on the morning after Thursday, Feb. 12, indicates that the unavoidable items of conversation among steelmen were the current shortage of sleeping time and the "Normandie." No analysis is needed, however, to be certain that many thousands of valuable words were uttered, both in and out of technical sessions, concerning matters of deep interest to members of the Iron and Steel Division. The opening session consisted mostly of papers that have appeared, or will appear shortly, in Metals Technology. One, however, that was not finished in time to be printed in any form, but that aroused great interest, was by E. L. Ramsey and L. G. Graper (Wisconsin Steel Works). Its subject was the production of high-sulphur steel by treatment with sulphur dioxide derived from anhydrous sodium sulphite or bisulphite added to the ladle or to the mold. The sulphide distribution in the finished steel is such that increased machinability and longer tool life result. Both items are of obvious importance in these days of mighty production.

Jan 1, 1942

No. 264. A long established company operating steel and iron foundries, machine and forge shops, whose varied products are sold to the Government, railroads, mining and contracting industries, etc., has, openings in both manufacturing and selling departments for men with technical education and experience who are not subject to military call. State full particulars, kind of position preferred and salary expected. No. 265. Young man wanted, technical graduate preferred, to superintend construction f a small charcoal blast furnace. Man with blast-furnace experience preferred. For the right kind of man this is, not only a permanent job but an opportunity. In writing, give full particulars as to age, education, experience, salary wanted, etc. No. 26.6. An important copper mining and smelting company in Arizona needs two or three metallurgical chemists, at salaries. ranging front $150 to $175 per month. No. 267. A consulting mining engineer needs two superintendents for developing chrome deposits near Philadelphia; and another technical man for other engineering work in the same vicinity. No. 268. An iron-mining company, in New York State needs a mining engineer with knowledge of geology and acquaintance with construction work; A married man, with about 10 years' engineering experience preferred.

Jan 2, 1918

By C. A. Heiland

FOR the past three years, the senior writer has carried out, with inter-ruptions, a series of investigations into the characteristics of prospecting seismographs of a wide variety of construction. Early in 1932, a com-plete equipment was developed for both refraction and reflection observa-tions; its first function being, however, the application in reflection shooting. The performance of the equipment proved to be highly satis-factory in a series of field tests' which were carried out by the junior writer, whose services were loaned to the Colorado School of Mines by courtesy of the Plains Exploration Co. in Denver. The various problems that were encountered in the construction of the equipment, in its application in the field, and in the interpretation of the results, are fully treated in Publication 47 of the Department of Geophysics of the Colorado School of Mines. Its first part deals with the various problems encountered in the design of the instruments, and presents a discussion of such topics as the free and forced oscillations of damped and undamped mechanical seismographs, the action of oscil-lographic recording instruments and amplifiers, the characteristics of electromagnetic seismographs, and the requirements of damping, natural frequencies and static magnification for the pickups, amplifiers and oscillographs used in refraction and reflection seismographs. Further-more, a detailed discussion of the various methods of static and dynamic tests of seismic receivers, and a description of the reflection equipment developed at the School of Mines is presented. Unfortunately, a delay has occurred in the publication of the first part of this investigation concerning the instrument problems. There-fore, the second part, dealing with the field problems, is herewith pre-sented first.

Jan 1, 1933

By Thomas T., Read

IT does not seem practicable to review all the other specialized curricula that have developed in the mineral industries field in so much detail as has been given for petroleum. Nor is it easy to draw a definite line between true curricula, leading to a designated degree in the special subject, and options, which may range from the mere substitution of one or two courses for others ' in the final years to differences so extensive as almost to amount to separate curricula. Even to attempt to catalogue all the options that have been offered at one time or another would , require too much space. The remainder of this discussion, there- fore, will be confined to three topics which seem to be of major importance. Mining and metallurgical curricula will be covered in a later chapter. Geology The first, from the historical view, is geology in its relation to the mineral industries. Previous, chapters have made clear that in the early years of mineral industry instruction in the United States economic geology and mining engineering, so overlapped one another that men who were by training and experience economic geologists were appointed professors of mining, while men who had graduated as mining engineers sometimes developed into professors of geology. Even today men whose basic training was in- geology as a pure science, and who perhaps took a doctor's .degree in that subject, have attained such distinction in the mineral industries as to be universally accepted as "mining men," and their right to be regarded as mining engineers would not be questioned, even though 'they did not .take a degree in engineering. Nevertheless the distinction does exist, and has been made a concrete reality in recent years by the enactment of

Jan 1, 1941

By Oliver Bowles

WAR necessities have spurred inventive genius in many fields. A grinding mill without any moving grinding parts stirs the imagination. Among the new and striking accomplishments in the heterogeneous group of nonmetallic industrial minerals is the use of an electric arc to speed up manyfold the difficult and delicate task of drilling a microscopic hole in a diamond, the hardest of all known substances. Outstanding in the field of optical research is the ability that man has developed to improve upon nature by making in the laboratory optical crystals many times larger than those usually found in rocky crevices. These are merely samples of numerous events and circumstances of noteworthy import, many of which are recorded in this review. Termination of the second World War in 1945 permits an appraisal of the effects of the conflict and the probable effects of the coming restoration of a peacetime economy on the nonmetallic mineral industries. Some industries were stimulated greatly by the war, notably mica, quartz crystal, graphite, spinning asbestos, potash, fluorspar, barite, and refractories. The large-tonnage industries connected with the building trades, however, were forced to curtail their activities, except where their products were needed for wartime construction. Their reconversion to peacetime production will not be difficult.

Jan 1, 1946

By James Bowron

CONSIDERING the importance of the steel trade and the strategic position occupied in it by the Birmingham District, it may be surprising to many to realize that even the first pig iron smelted with coke was made in Alabama on Feb. 28, 1876, although merchant pig iron had been produced in Rockwood, Tenn., in 1867, a plant which is still in active operation. The heavy deposit of Clinton ore extending from Pennsylvania into Alabama, varying greatly in accessibility on account of geological changes such as erosion or anticlinal upthrow, varies equally as much in thickness and in quality. The brown ores extensively scattered through the South also vary materially in quality, some being relatively low in phosphorus and high in manganese, and vice versa. The red ore varies materially in phosphorus, but the iron produced from these ores was always considered to be too high in phosphorus for treatment by acid Bessemer or open hearth and did not contain sufficient for the basic Bessemer process. Under these conditions there remained only the basic open hearth as a possibility, and for many years it appeared impossible to use it, because, with coke smelted iron, the silicon was too high to permit its use in basic lined furnaces.

Jan 1, 1924

By A. M. Gaudin

CHANGES in industrial practice, in plant design, and in research methods which are so clearly to be seen on every hand, have affected the mineral industry as well as others. In particular, ore dressing has passed through a revolution in practice brought about by the introduction of flotation and other quasi-chemical methods, until it has ceased to be solely the mechanical preparation of ores. In fact, the term "ore dressing" itself is obsolescent, and "mineral dressing" has been growing in popularity. This assures adequate recognition of the fact that mineral substances other than ores, e.g. coals, clays, and cement rock, are treated by the same general methods. As a result of these industrial changes it was felt that a complete rearrangement of the curriculum and laboratories at the Massachusetts Institute of Technology would be ad-vantageous. Such a rearrangement would allow instruction and research to proceed in wider accord with industrial evolution and the needs of our times.

Jan 1, 1942

By Paul L. Allsman

Mankind has found lime and limestone a useful mineral commodity since the dawn of history. The ancient Egyptians knew how to make use of it as a building material, and it has been used in agriculture for centuries. More recently, limestone became a cheap ingredient in some chemical processes, in metallurgy and in the manufacture of alkalis. The consumption of lime and limestone has never diminished; in fact, the process of lime production remained the same until the recent introduction of the modern rotary or vertical kilns. However, the demands of industry and agriculture are changing the usage patterns of the commodity. The USBM now keeps statistics according to type- quicklime, hydrated lime and dead-burned dolomite -and according to market, whether open or captive.

Jan 6, 1966

By AIME AIME

MORTIMER ELWYN COOLEY, dean of the College of Engineering and Architecture of the University of Michigan, has been elected president of the American Engineering Council of the Federated American Engineering Societies. This was announced at a meeting of the Executive Board of the Council held at the Cosmos Club in Washington on Sept. 30. Dean Cooley assumes office at once. The new head of organized engineering is a past president of the American Society of Mechanical Engineers and has a long record of distinguished service in education, under the government and in private capacities. He was born in Canandaigua, N. Y., March 28, 1855, and was graduated from the United States Naval Academy in 1878. With his classmate, Dr. Ira N. Hollis, he was ordered to the U.S.S. "Quinnebaug," then fitting out at the Norfolk Navy Yard preparatory to a cruise in the Mediterranean.

Jan 1, 1921

By Walter Miller

NOW, after a year's continued impact of war, the task of the petroleum-refining industry stands out clearly and looms up in larger aspect. This time it is not, as it was so largely in the first World War, simply a matter of increased quantity- more and more of the same petroleum products that had substantially been standard for years. In this era the emphasis is largely on newer and improved materials which had been produced, if at all, in comparatively insignificant quantities, and for which manufacturing equipment was not available on a large scale. At the beginning of 1942 four great product needs (besides a number of lesser one-) confronted the industry: 100-octane aviation gasoline, toluene for T.N.T. production, high-quality lubricating oils for aviation and Army equipment service, and petroleum chemicals for synthetic rubber manufacture.

Jan 1, 1943

By AIME AIME

LAST month we published (p. 440) the first half of the L discussion by O. E. Kiessling of the paper on copper by Mr. Vogelstein that appeared in the same-issue, but lack of space made it necessary to hold the remainder for this number. Mr. Kiessling now asks to have the last " sentence of the part already published revised to the form given in the first sentence which follows, and also asks that the two parts, though necessarily published separately, be read together, as a mistaken impression may be derived from the first Dart unless it is read in connection with the statement of the Bureau of Mines policy respecting secondary metals which is here published. .

Jan 1, 1931

By T. F. Witherbee

On .the 22d of November, 1879, white, iron unexpectedly ap peared while working the Cedar Point Furnace, Port Henry, N Y., on the following burden, calculated to turn out mill and foundry iron: Anthracite coal,. ., .. .. 8000 pounds. Connellsville coke,. ..1500 " Total,..4500 " Old Bed ore,........ 3750 " New Bed fine ore,. ..2000. " New Bed chunk ore,. .. 1000 " Kearnev hematite ore,.750 " Total,..... 7500 " Magnesian limestone,. 1665 " Common limestone,. ...835 " Total,........ 2500 " The production per week since making mill iron-—from September 1st, 1879, to date, seven weeks—was 412 gross tons. Ore was not immediately taken off, as nothing serious was looked for. The iron for the next week graded from No. 4 to white, and in six days the make was 2741/2 tons. At 10 p.m., Friday, the 28th, a slip of -14 feet occurred, and on Saturday, at 5 A.M., another of 3 feet on the south side and 7 feet on the north side took place. At this time it was found that the south side had been hanging for over a week—a fact which had not been reported. Throwing off the wind, to produce slips and reduce pressure, had been tried with no effect. The stock, as seen through the tuyeres, seemed to consist almost entirely of coal, with just enough infusible cinder to cement it into a mass through which the blast could not be forced. At 3.50 A.M., Sunday, the 30th, the first cinder seen in seventeen hours came into tuyeres Nos. 1, 2, 3, and 6. At 9.30 A.M. No. 3 was taken out to see if the stock

Jan 1, 1881

By Lawrence Addicks

Some three years ago the smelter connected with the Chrome, N. J., refinery of the United States Metals Refining Co. found itself embarrassed by constantly increasing piles of unsmelted blast-furnace flue dust. The charge was fine and 10 to 15 per cent. of it was blown over into the flue. Sulphur was at that time too scarce to make the sintering of the finer part of the charge attractive, and raw-ore smelting in a reverberatory with a partly oxidized charge was not to be thought of. A great many schemes were considered, including leaching, blowing into the converters, and briquetting, the problem finally narrowing down to blast roasting and nodulizing. It was found by experiment that blast roasting would not yield a satisfactory sinter without the addition of coke dust or sulphide fines to augment the fuel value of the flue dust, and on this account, together with the low first cost of a kiln, the latter was decided upon. A couple of tons of flue dust were tried out in the experimental kiln in the laboratory at Yorktown, Va., of J. H. Payne, who acted as consulting engineer in this connection. This kiln was approximately 2 ft. in diameter and 20 ft. long and was fired with fuel oil. A run of several hours yielded excellent nodules. The ki1n showed no tendency to build in and form "nose rings" and gave a fuel consumption of 50 gal, of oil per ton of flue dust. There was no indication of any stack loss. The roasting was strongly oxidizing. A study of what full-size kilns were doing on cement clinker and on nodulizing pyrites cinder indicated that a 60 by 6 ft. kiln would certainly not consume over half of the oil per ton of flue dust shown on the test and as fuel oil at that time was selling around 2 1/2 c. per gallon it was decided to let it go at that. A 60 by 6 ft. kiln was decided on, as that size is standard in cement practice, although fast being replaced by much larger ones with their greater fuel economy, and as it fitted in the building space available. A 6-in. brick lining brought the net diameter down to 5 ft. The inclination

Jan 1, 1915

One of the engineering proposals in the last Congress which was of interest to engineers was the soldiers' land settlement plan proposed by Secretary Lane, under which returned soldiers, sailors and marines would be employed on construction work in the reclamation of swamp and arid lands and would thereafter be given preference in the selection and settlement of those lands. This bill failed in the fillibuster at the end of the session. It is likely that some sort of a plan for soldiers' settlement will come before the next Congress. A new bill has been written up for introduction at the next session which proposes an "infiltration method" of buying improved farms in established communities for' the soldiers' settlement purpose, under the authority and direction of the Farm Loan Board. The contrast of this bill to the one recommended by Secretary Lane is of vital importance to engineers at this time; first, because of the broad engineering improvement program that the latter bill proposes as against no engineering improvement under the infiltration plan; secondly, the community settlement plan of Secretary Lane means improvement of waste lands requiring much engineering work.

Jan 7, 1919

By R. W. Moore, A. B. Kinzel

Although the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approximately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cenlentite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consideration of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:' C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown In Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850" C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the sample after 5 min. at 850" C. is shown in Figs. 3 and 4, and the nest of pearlite surrounding the graphite nodules is most satisfactory evidence of the character of the nodules. As the length of time of heating at this temperature increases, the pearlitic zone increases, with final restoration

Jan 1, 1935

By R. W. Moore, A. B. Kinzel

Although the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approximately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cenlentite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consideration of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:' C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown In Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850" C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the sample after 5 min. at 850" C. is shown in Figs. 3 and 4, and the nest of pearlite surrounding the graphite nodules is most satisfactory evidence of the character of the nodules. As the length of time of heating at this temperature increases, the pearlitic zone increases, with final restoration

Jan 1, 1935