Search Documents

By Andrew Fletcher

AS good health is the most important asset in life, the development of healthful conditions should be the one common meeting ground of agreement between management and labor. Health should not be a subject to be pulled apart, shoved around, or bargained about. Differences of opinion may exist in the procedure and techniques employed in approaching the goal of maintaining the health of workmen, and in the method of increasing the ultimate profit of the employer by improved working and living conditions. Such matters are doubtless appropriate subjects for discussions between the interested parties, but techniques are only tools. If an employer fails to remedy a hazard or a menace which contributes to poor working condlions, this constitutes a legitimate grievance. It should not be necessary, however, nor is it desirable that fundamentals of health maintenance become matters of collective bargaining, any more than should the principles of management and engineering. I have been especially concerned during the last few months with the propaganda in collective bargaining negotiations throughout the country for including in union contracts a given number of days of sick leave with pay. We all

Jan 1, 1946

By Lendall P. Warriner, Blandford C. Burgess

Jasper County lies just north of the geographical center of Georgia, bounded on the west and north by the Ocmulgee River. The county seat, Monticello, is approximately 65 miles east-southeast of Atlanta and 40 miles north of Macon. It is served by the Macon-Athens branch of the Central of Georgia Railway Co. and by five paved highways converging from adjoining county seats. Farming and lumbering are the principal local occupations. About half the county is covered with pine and mixed hardwoods; a large part of the forested land is owned by the Soil Conservation Service of the Department of Agriculture in its Piedmont Land Utilization Project. The topography is one of gently rolling field and forest with occasional hills rising 100 ft or: more above the creek beds. Though annual rainfall is in the neighborhood of 60 in., most of it falls in torrential downpours of short duration which tend rapidly to erode the red soil and convert the country roads to greasy tracks of red mud.

Jan 1, 1949

By C. D. Dolman

SINCE the outbreak of the war we have discovered in the United States minerals of which there was no general knowledge, and which compared very favorably with anything that could be found in any foreign country. One of these was magnesite, or the carbonate of magnesium as it occurs in nature. This mineral crystallizes in the rhombohedral form, has a specific gravity of 3.00, molecular weight of 84 4, molecular volume of 28.1, and a hardness of 3.5 to 4.5.1 Had it not been for the development of the California deposits of this mineral and the discovery of immense new deposits in Stevens County, Wash., the production of steel during the war would have been more seriously handicapped than it was. Now, that the war is over, we face the possibility of competition' with the cheap Austro-Hungarian magnesite; and while that may not he so cheap as it was before the war, adequate protection should be given the producers in this country to insure the full development of our own resources. The consumption of magnesite in the United States in 1913, the year preceding the war, was 172,591 tons of calcined and 22,872 tons of crude magnesite. Less than 3 per cent. of this amount was produced at home. At the present time, practically all of the magnesite used in the United States is produced at home. Expensive plants have been constructed, extensive exploration work done, and production pushed to the utmost to supply the necessary requirements of the war. Thus a considerable industry has been built up within our borders. Some magnesite has been imported from Canada and Mexico, but the Canadian ore was of an inferior grade and could not be used satisfactorily. During the year 1918, production decreased in both the United States and Canada; the production in the United States was 225,000 tons in 1918 as against 315,000 in 1917, and in Canada 39,365 tons in 1918 as against 58,090 in 1917.

Jan 8, 1919

By J. Trevor Eyton

This paper addresses some of the financial risk hedging mechanisms available to a corporation contemplating entering the mining business at a significant level of investment. The approach which I have adopted is that of a case study relating to the risk hedging aspects of Brascan Limited's acquisition of 46% of Noranda Inc., formerly Noranda Mines Limited, followed by some remarks on options open to mining companies for reducing financial risks. To appreciate the rationale for Brascan committing over (Can.) $800 million to the natural resource sector, some knowledge of Brascan's parent company, Edper Investments Ltd., is required at the outset. Edper Investments, prior to acquiring a 48% interest in Brascan, controlled Trizec Corporation, one of the world's largest property companies. Edper also was involved in the financial services sector through Continental Bank of Canada and Hees International Corporation. For some considerable time prior to Edper's investment in Brascan, Edper felt a need to provide a better balance to its portfolio of property and financial services. Brascan was rich in cash, relatively unleveraged, and with important existing holdings in natural resources and consumer products. The acquisition of a controlling interest in Brascan provided an opportunity to balance Edper's portfolio of property and financial services with world class acquisitions in natural resources, supplemented by consumer products and financial services. The end result of Brascan's activities over the last few years is illustrated by the following analysis of the book value of Brascan's assets at the end of December 1983. [Can.$% Millions _ Natural Resources81748 Consumer Products 654 38 Financial Services 157 9 Other Operations895$1,717100% ] Source: Brascan 1983 Annual Report. The large emphasis on natural resources came about from the fact that for Canadians operating mainly in Canada, natural resources were attractive. We were impressed by Canada's position in the world natural resource industry as illustrated by some of the following statistics: [CommodityCanadian Estimated Production In 1983 As % of World Total Newsprint 30 Potash 21 Uranium 18 Molybdenum 17 Zinc 17 Pulp 16 Nickel 16 Saw Logs 11 Silver 8 Copper 7 Lead 6 Gas 5 Oil3] Source: U.S. Bureau of Mines and Brascan estimates. In addition, the quality of Canada's reserves looked good to us. The polymetallic nature of many of Canada's orebodies offered a hedge against risk relating to any one metal. Put another way, the by-product metal credits offered a net operating cost advantage with respect to many of the metals mined. Our energy costs also appeared to provide Canada's natural resource industries with an advantage. We considered Canadian mining expertise as amongst the world's finest, as were the exploration equipment and technology developed in Canada. In addition, Canada offered a stable political climate and one we knew. Further, we felt the Canadian Government's future role in the industry would, on balance, be benign, partly because the Canadian content of the mining industry was very high in contrast to the petroleum industry. Granted, we could find cheaper sources of copper; however, to do so would involve venturing into regions where country risks were higher.

Jan 1, 1985

Jan 1, 1965

By Evan Evans

WITH the expiration on April 30, 1941, of the agreement between the anthracite operators and the United Mine Workers of America, a new agreement was entered into, providing for a general wage increase of 7 1/2 per cent effective May 1, to be brought to a total of 10 per cent on Oct. 1. Contract rates were increased from the rates established under the agreement of September 1923, and hourly rates were raised above the agreement of May 1936 as modified from the eight-to seven-hour day in May 1937. The new rates are to be in force for the duration of the agreement, ending April 30, 1943.

Jan 1, 1942

By K. A. Grange, W. S. Holt, E. T. Tkac

Quantitative knowledge of the time clement involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 13s-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Aeaand Ae,), the temperature range of martensite formation, and the end-quench harden-ability. These data are directly applicable to the hcat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. Material All specimens were prepared from a 1 1/4 i-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: AIn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, I.j7: Mo, 0.36: All 1.26. The forged bar was normalized from r750°F (95s°C) and then tempered for one hour at rzoo°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. Equilibrium Transformation Temperatures In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Aep, and the maximum temperature at which austenite is completely unstable, Ael, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1948

By W. S. Holt, K. A. Grange, E. T. Tkac

Quantitative knowledge of the time clement involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 13s-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Aeaand Ae,), the temperature range of martensite formation, and the end-quench harden-ability. These data are directly applicable to the hcat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. Material All specimens were prepared from a 1 1/4 i-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: AIn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, I.j7: Mo, 0.36: All 1.26. The forged bar was normalized from r750°F (95s°C) and then tempered for one hour at rzoo°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. Equilibrium Transformation Temperatures In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Aep, and the maximum temperature at which austenite is completely unstable, Ael, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1948

By J. M. GLEDHILL

IT would doubtless have been felt by many but a few years back that there was little left to be said on the subject of crucible tool-steel, and that something akin to finality had been arrived at in its manufacture and general treatment. Probably such feeling was justifiable when it is remembered that the making of steel in crucibles is by far the oldest method known, dating back from time immemorial, it being indeed impossible to accurately trace its origin and earliest development; but it seems certain that carbon-steel was made and used thousands of years ago for cutting-tools. Proof of this may be seen by the marvelous carvings and workings on the intensely hard stone-work of the ancients, for it would be difficult to conceive by what means, other than with steel tools, such work could have been executed; and it is wonderful to contemplate that steel cutting-tools should have been used so long ago, whilst the principle of manufacturing them-that is, by fusion of iron and charcoal in crucibles-was then in a measure on the sane lines as we work on at the present day. Archaeologists have discovered that the Chinese made steel in crucibles long before the Christian era. " Wootz " steel fabricated in India centuries ago was crucible steel, as was also the celebrated Damascus steel, produced at the forges of Toledo, and, curiously, this latter steel furnishes' yet another proof that "There is nothing new under the Sun," for it is recorded that Damascus steel contained certain percentages of tungsten, nickel, manganese, etc., some of the very elements, in fact, contained in the present modern high-speed steel, so that a latent high-speed steel may be said to have existed

Mar 1, 1905

By P. Barnes

The sums given in the accompanying table are those actually paid for material and labor up to about August, 1875; but, as some parts of the machinery were not wholly completed at the starting of the works in September, 1875, the statement cannot be taken as an absolutely correct note of the total cost. A complete description, with engravings of the building and machinery, was given in Engineering, April 26th, 1878, in a paper by Messrs. A. L. Holley and Lenox Smith, to which convenient reference may be made. A detailed list of the construction accounts has been given in a paper, by the present writer, in vol. vi, Transactions of the Institute. A summary is given in the table of the items in each class which enter into the total cost, and also a note of the proportion which each of these items forms of the whole. A concise view may thus he obtained of the facts embodied in the statement as a whole, even though it cannot lay claim to completeness in showing the entire or final cost. An urgent suggestion has reached the writer from a distant country that such statements of cost to be really most serviceable should give the details in days of labor, in weight of iron, and in number of brick, and to this an assent is most cordially yielded. It is true, however, that the mere labor of copying arid compiling these details to such a degree of minuteness, would be very great, and, in any event, the probable difference between the plans of an existing establishment and one projected, would be so wide as to render even so complete a statement of cost of little more real service than the approximate notes given herewith.

Jan 1, 1879

By P. Barnes

THE sums given in the accompanying table are those actually paid for material and labor up to about August, 1875; but, as some parts of the machinery were not wholly completed at the starting of the works in September, 1875, the statement cannot be taken as an absolutely correct note of the total cost. A complete description, with engravings of the building and machinery, was given in Engineering, April 26th, 1878, in a paper by Messrs. A. L. Holley and Lenox Smith, to which convenient reference may be made. A detailed list of the construction accounts has been given in a paper, by the present writer, in vol. vi, Transactions of the Institute. A summary is given in the table of the items in each class which enter into the total cost, and also a note of the proportion which each of these items forms of the whole. A concise view may thus be obtained of the facts embodied in the statement, as a whole, even though it cannot lay claim to completeness in showing the entire or final cost. An urgent suggestion has reached the writer from a distant country that such statements of cost to be really most serviceable should give the details in days of labor, in weight of iron, and in number of brick, and to this an assent is most cordially yielded. It is true, however, that the mere labor of copying and compiling these details to such a degree of minuteness, would be very great, and, in any event, the probable difference between the plans of an existing establishment and one projected, would be so wide as to render even so complete a statement of cost of little more real service than the approximate notes given herewith.

Jan 1, 1879

The Iron and Steel Committee of the American Institute, of mining and Metallurgical Engineers held a joint session with the American Foundrymen's Association during the Annual Meeting of the Institute in February, 1928, for the purpose of discussing blast-furnace operations and the character of pig iron and castings. Dr. Richard Moldenke presided. H.. H. Sweetser, who was named on the program as the presiding officer of the session, was unable to be present, but sent a letter in which he said: " The meeting we had here last year and the meeting held in Chicago last June showed a desire on the part of blast-furnace men and users of pig iron to get the facts regarding the influence on castings made from pig iron produced in blast furnaces under varying conditions of temperature, mixture and local furnace operations. It has been my hope that at this Round Table we might he able to formulate a series of tests that, would give us the desired information. "Several independent blast-furnace investigations have. been, and still are being, carried on in different sections of the country. The furnaces investigated include a southern furnace, a middle-west furnace, a western furnace and a Chicago district furnace. The results so far show distinct characteristics for each of the four furnaces. It is possible that a furnace in the eastern part of the United States would be different from all the others. "It is hoped that a plan of action can be worked out at your meeting today whereby the IT. S. Bureau of Mines will be able, to carry on more extensive work in connection with the research departments of the different iron and steel companies and the big consumers of pig iron. "No one group can get all of the, information but if the different investigations can be coordinated it will he possible for us to (Iran. conclusions regarding the effects of varying conditions in blast-furnace practice on the pig iron produced and the castings made there from." DISCUSSION R. Moldenke, Watehung, N. J.—I was across the -water this summer and saw some of those interested in an investigation of this kind. 'I'hey told me that in Germany, where they had a joint committee of blast-furnace operators and foundry-

By William Paxton Hewitt

Mineral deposits of western Utah and eastern and central Nevada have produced in excess of $8,500,000,000 since 1871. Through 1965, Bingham Canyon had produced over $4,600,000,000 and seven other camps over $100,000,000 each, principally from base metals. In addition, they yield iron and uranium ores; contain the world's largest beryllium reserves; and have produced the United States' most important gold discovery in 25 years. The area is famous for its silver production and its bonanza-type precious metal deposits, but such production has become unimportant. The area's greatest producers of metallic wealth are base-metal deposits in limestones and porphyry-type copper ores. In contrast to silver's decline, gold production has been rising-the result of by-product operations at Bingham Canyon. The area also contains gold deposits in which the gold is so finely disseminated it is not recoverable by panning. The area's gold ores frequently are associated with realgar, cinnabar, and carbon. The ore deposits generally are attributed to Tertiary intrusives,* but, at Mountain City, they may be related to Paleozoic volcanism. Mountain City has yielded rich chalcocite from quartz-pyrite-chalcopyrite bodies in siliceous sediments. Regional stratigraphy and structure are difficult to interpret, 69 per cent of the area being obscured by alluvium or volcanics. In general, central Nevada consists of chert, shale, silty sandstones, lavas, and pyroclastics; eastern Nevada and western Utah of many alternations of limestone, shale, and sandstone. Central Nevada has been structurally active since late Devonian. Although granitic stocks may have intruded eastern Nevada and western Utah prior to the Cretaceous, these areas remained quite stable until affected by the Laramide Revolution. Precambrian exposures, occupying 3 per cent of the area, have not been important hosts. However, the question is raised as to whether Precambrian carbonates, properly situated with respect to invading mineralizers, might yet prove to be important. This paper describes 16 precious metal camps, 6 limestone replacement districts, 2 silver-base metal vein deposits, and 9 miscellaneous types and discusses briefly the 11 * Some ores, as at Ely, are associated with intrusives of. Cretaceous age. major camps that are described in detail in this Volume.

Jan 1, 1968

By H. M. Howe

Page 1. Introduction............................514 2. Definitions.............................517 3. Brevity of the Heating........................517 I. THE HARDENING OF THE BORE..............517 4. The Hardening of the Bore.....................517 5. The Thickness of the Hardened Layer.................517 6. Martensitization..........................518 7. The Hardening Repetitive ......................519 8. The Temperature Cycle.......................519 9. The Hardened Layer is the Merged Layer............... 521 10. The Progressiveness of Merging....................521 11. The Progressive Thickening of the Hardened Layer from Round to Round. 523 12. Merging and Hardening are Cumulative................523 13. Three Additional Causes of the Progressive Thickening of the Hardened Layer 525 14. Progressive Roughening of the Bore..................525 15. Avoidance of an Endothermic Transformation.............525 16. Asymptotic Retardation of the Thickening of the Hardened Layer.....527 17. The Troostitic Layer........................ 529 18. The Usual Lack of Martensitic Markings................529 19. The Thickness of the Hardened Layer Should Increase with the Quantity of Heat Taken up by the Walls of the Bore.................530 20. The Decrease of the Thickness of the Hardened Layer from Breech to Muzsle 531 21. Phstic Deformation as a Contributory aCause of Hardening........531 22. In What Way May Plastic Deformation Hasten Hardening?....... 535 23. Possible Need of Coarsening.....................535 24. Carburization as a Cause of Hardening..........:.....536 25. Does Hardening Increase Erosion?..................-538 11. THE CRACKING OF THE BORE ...............539 26. Appearance of the Bore and Cracks in Elevation............539 27. The Cracks in Elevation in the Rear Ring...............539 28. The Cracks in Elevation in the Forward Ring.............540 29. The Copper Network in the Grooves.................540 30. The Cracking of the Lands......................541

Jan 1, 1918

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metallurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial investment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding. The capacity of the new kilns was established at 4000 bbl. per day. Two new kilns were installed, each with a capacity of 80 bbl. per hour. Since 625 lb. of raw material is required to make a barrel of finished cement, the capacity of the grinding plant for the new kilns had to average only 1250 tons per day. Sufficient additional grinding capacity had to be provided for the two remaining old kilns, or their possible replacement by a third new kiln. The grinding rate, therefore, was set at 90 tons per

Jan 1, 1939

By AIME AIME

Change of Meeting from Birmingham to Chattanooga. In consequence of the disturbed conditions attending a long¬continued labor strike in Alabama, the meeting of the Institute was changed from Birmingham, Ala., to Chattanooga, Tenn., where it will. begin on Thursday evening, Oct. 1, 1908. Information. of this change bad been sent to the newspapers through the Associated Press, and by circular to all members, when news was received of the sudden and unexpected termination of the strike referred to. It was, unfortunately, too late to change once more the arrangements for the meeting. But it is hoped that the cordial invitation of the citizens of ,Birmingham may be renewed and accepted at a future time, not too remote. Office Facilities for Visiting Members. A separate room in the suite occupied by the American Institute of Mining Engineers on the ninth floor of the United Engineering Society Building, has been equipped with furniture and telephone extension for the temporary use of members of the Institute or of sister societies, or visitors suitably accredited. Members of the Institute visiting New York for a short time, who need office facilities during their stay, or members residing in the city. who need temporary office accommodation, can arrange to have set apart for their exclusive use a room, equipped with office furniture, telephone, etc.,. in the suite of the Institute. It is not the intention to give possession of the room to any individual for an indefinite time, but to offer to members of the Institute an opportunity to acquire a well-located, well-equipped business headquarters to carry on transactions which

Jan 9, 1908

By R. W. Smith

Many industries such as the cement industry handle large quantities of limestone and clay slurries. However, at present very little is known about the flow properties, such as friction loss due to flow of slurries in pipelines. This lack of knowledge has made it often very difficult to calculate the total dynamic head of a proposed slurry handling system, and therefore has often made the selection of correct size slurry handling equipment difficult. Because of lack of knowledge about slurry flow a study of slurry flow theory has been made at the Portland Cement Association's Research and Development Laboratory with the idea of developing a method whereby friction losses due to slurry flow may be predicted for any size pipeline. The flow equations developed have been checked by pilot plant size equipment. DERIVATION OF FLOW EQUATIONS It has been known for some time that limestone and clay slurries handled in cement plants do not flow in the same manner as a Newtonian fluid such as water. When a Newtonian fluid flows the shear stress at any flow velocity is proportional to the rate of shear. This phenomenon can be illustrated by a line (Figure 1). The viscosity of the fluid is the slope of the curve. Thus, the flow properties of the material may be characterized by a single materials constant: viscosity. When a non-Newtonian fluid with the type of characteristics exhibited by limestone and clay slurr-ries flow, a similar curve can be constructed (Figure 2). This graph is a shear diagram of a Bingham plastic non-Newtonian fluid. It should be noted that with the Bingham(1) plastic type of flow viscosity, the slope of the curve, is still an important materials constant. In addition, however, there is another materials constant, namely the yield stress of the material. One way to visualize this constant is to consider it as the amount of energy that must be put into a Bingham plastic material to start it flowing.

Jan 1, 1961

By A. Poll, J. E. Stantan, L. J. Jolley

THE basic problem in the generation of water gas from carbonaceous fuels and steam is the supply of the heat of reaction, and in general the source of this heat is the combustion of a further quantity of carbon with oxygen. Existing and proposed processes for complete gasification differ in the methods employed for transferring this heat to the fuel, and involve one or other of the following alternatives: 1. Use of a steam-oxygen mixture as the gasifying medium, so that the combustion and gasification reactions are combined. 2. Alternate passage of air and steam through a fixed bed, as in conventional water-gas production. 3. Cyclic passage of fluidized fuel through combustion and gasification zones. 4. Intense preheating of steam and of a portion of the gas made, and recirculation of this mixture through the fuel bed. 5. Supply of heat to the fuel bed through an externally heated wall. Except for the conventional water-gas process using large coke or low- volatile coal, only processes in the first group, operating with steam and oxygen, have proved practicable with fuels other than brown coals and lignites. A possible exception, which has not so far reached a commercial scale, is the moving-burden process developed by Imperial Chemical Indus- tries, Ltd. The cost of industrial oxygen is so high that its use can probably be justified only if it is attended by substantial savings in other directions; for instance, the use of cheap fuel. In the United Kingdom, no very cheap solid fuels are available, and it is unlikely that an oxygen-gasification process could compete economically with conventional production of blue water gas from coke. Hence particular interest attaches to all possibilities of making water gas without using oxygen, if any possible saving in fuel or other costs is involved. The cheapest and most abundant coals in the United Kingdom are the low-rank noncaking bituminous coals in small and ungraded sizes, typically those from the East Midlands coal field, and-fines of high ash content produced in coal-cleaning operations. A process capable of gasifying

Jan 1, 1953

By E. P. Abrahamson II

The effect of transition elements which form binary solid solution upon the recrystallization temperature of zirconium has been investigated. All additions raised the recrystallization temperature. A correlation is obtained between the logarithm of the rate of change of recrystallization temperature with atomic percent solute and the free atom ground state electron configuration of the solute element. ThE work of Abrahamson, et al., on dilute binary solid-solution alloys indicated a correlation between the free-atom ground state electron configuration of the solute and either the brittle-ductile transition or recrystallization temperature. These studies were carried out on bcc base materials. The implication is that the outer s and d electrons of the solute are the prime determinant of the absolute rate of change of recrystallization or transition temperature. Furthermore, the limit of linearity has been shown to be a function of solute electron configuration for recrystallization in iron and vanadium. To date no Complete systematic recrystallization study of dilute binary zirconium base alloys has been made. It is the purpose of this study to note whether the change in solvent structure from bcc to hcp will influence the correlation. It was also desired to learn more of the role of the electron configuration of the solvent on recrystallization temperature. PROCEDURE All alloys were made using 99.87 pct Zr with 0.01 Cr, 0.04 Fe, 0.006 Hf, 0.003 Mg, 0.003 Mn, 0.003 N, and 0.080 0 (132 BHN). The solute elements were 99.9 pct pure. According to the published binary phase diagrams6 and metallographic examinations at X750, all alloys used were solid solutions. The alloys were arc melted and remelted six times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot pressed at 950°C to 0.450 in., upset pressed to 0.350 in., and annealed at 800°C for 1 hr. The specimens were then Blanchard ground to 0.250 in., removing 0.050 in. from each side. The grain size of the material at this stage was found to be 8000 100 grains per sq mm. The specimens were then cold rolled to 0.130 in. and cold pressed to 0.125 in., yielding 50 1 pct cold work. All alloys were then chemically analyzed for the principal addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The rolled sheet was cut into 6.75 by 0.25-in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was 250o to 900°C over the 6-in. length, recorded continuously by six thermocouples resting on each specimen. Control was 3oC, accomplished at the hot end. The recrystallization temperature was determined metallographically using polarized light. The criterion chosen was the point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be 3°C. RESULTS Three different pure zirconium specimens were tested, and the recrystallization temperature was

Jan 1, 1962

By David B. Dill, Edgar R. Lea

The zinc deposits of the Balmat-Edwards Division of the St. Joseph Lead Company in northern New York State provide some 10 per cent of the domestic zinc produced annually within the United States. These complex ore deposits are contained within marbles of the Precambrian Grenville series, in a repetitive sequence of dolomites and silicated units. The Balmat ore bodies are localized at various intervals throughout some 1800 feet of the stratigraphic column on the northwest side of a band of gneiss that has continuity to the Edwards area, some 10 miles to the northeast. The Edwards ore bodies are located to the southeast of this gneiss. The marble formations are thought to have included repetitive intervals of marine sedimentation that provided mineralized source "beds" and were subsequently folded, flooded, and injected with melts at great depth and were sheared, recrystallized, and reconstituted. Detailed structural and stratigraphic studies throughout the northwestern Adirondacks, in the Balmat-Edwards district, and at each mine in particular indicate the close dependence of the ore deposits on the enveloping structure whether it be local, district-wide, or regional in scope. Primary folding has developed a northeast regional trend with northwest dips. Secondary folding has been developed by an almost horizontal northeast-southwest-oriented shear couple in the plane of the regional trend. The secondary folding has produced crossfolds that intersect the regional northeast trend and plunge north to northwest at various angles. The ore bodies are found within certain stratigraphic horizons where repeated alternation of competent and incompetent beds encouraged unusually complex folding. Analysis of individual mine structures indicates that the location of each deposit is controlled by structural crossing of primary and secondary folding. The ore bodies, which are tabular, lenticular, or pod-like in form, have features that suggest parallelism to true bedding or modified flow banding, developed by northeast-southwest shearing stresses related to the development of the crossfolds. The ore deposits in general follow both structural and recrystallization trends within the wall rocks. Mobilization of the pre-metamorphic ore minerals is believed to have involved a combination of plastic flow under stress and solution of the sphalerite, minor galena, and pyrite. The ore fluids are thought to have been guided by secondary shearing and microbrecciation into structurally prepared areas where reprecipitation took place. The presumed premetamorphic mineralization now exhibits epigenetic high-temperature features related to late-stage metamorphism.

Jan 1, 1968