Search Documents

Thickener Modelling - Incorporating Shear Effects

Sep 13, 2010

By Hamid Maleki

Roof falls are one of the leading ground control problems that adversely influence productivity and worker safety in underground mines, construction sites, and nuclear waste repositories. To control roof stability problems, the operator needs to have practical methods for measuring changes in strata conditions and criteria for defining the timing of secondary support installation. The objective of this study was to develop measurement techniques and criteria for assessing roof conditions at the mining face. An integrated rock deformation and tomographic imaging method was developed and applied at two sites in a western U.S. trona mine. It was shown that rock damage occurred at a deformation of 30 to 60 mm (1.2 to 2.4 in) (2 to 4 pct strain) and was associated with a significant (16 pct) reduction in wave velocity. Thus, supplementary support may be installed when there is a measured change in wave velocity of at least 16 pct. Tomographic measurements can be obtained in rocks rapidly, thus providing a powerful tool for analyzing growth of failure and for installing supplementary support systems in a timely manner.

Jan 1, 1996

By D Reddy

Rosh Pinah Zinc Corporation is a zinc-lead mine located in southern of Namibia. It is currently considering the development of a low grade ore body containing about 2.8% zinc. This ore can be utilised by the concentrator if it could be upgraded prior to the ball mill. Preliminary work indicated that the ore may be upgraded in a pre-beneficiating stage by using dense medium separation, X-ray sorting or a combination thereof to a feed grade of minimum 9% zinc. This paper describes the process followed in evaluating the technologies for pre-beneficiation. The results from test work indicated that the low grade ore is amenable to pre-beneficiation by both dense medium separation and X-ray sorting. A comparison between the two technologies showed that dense medium separation marginally outperformed X-ray sorting on grade and recovery. The results for the X-ray sorting were achieved by tuning the calibration curve specifically for the samples tested.

Jan 1, 2008

By J. Bilant, B. Carlson, N. Gow

"High-pressure grinding roll (HPGR) technology was evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact on metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data were consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8 percentage points, from 61 percent to 69 percent, and shorten the overall timing of silver recoveries from 20 years to just more than two years.The Rochester Mine, and associated valley fill heap leach facilities is an openpit silver and gold mine located in Pershing County, NV, approximately 42 km (26 miles) northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7 million oz silver (Ag) and 51,000 troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8 in. ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers.Historical recovery rates of crushed Rochester ore averaged 61.4 percent Ag and 95.9 percent Au over a period of 20 years (Robinson et al., 2018). These rates were derived from third-party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher and/ or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project."

Sep 1, 2019

By Alain Pecker

The choice of a design concept for a bridge foundation is guided by various factors; several of these factors are indeed of technical origin, like the environmental conditions in a broad sense, but others non technical factors may also have a profound impact on the final design concept. The foundations solutions adopted for the Rion Antirion bridge are described and an attempt is made to pinpoint the major factors that have guided the final choices. The Rion Antirion bridge is exemplar in that respect: the foundation concept combines the simplicity of capacity design, the conceptual facility of construction and enhances the foundation safety. The design of these foundations was a very challenging task which required full cooperation and close interaction with all the parties involved: concessionaire, contractor, designers and design checker.

Jan 1, 2005

By A Webster, T Murphy

Block cave mining, in its broadest sense, has transitioned from an orebody/rock mass determined method of extraction, to a low-cost and high production mining method that may be applied to any large ore deposit. This inherently means that caving is now required in more complex rock mass conditions where assistive damage, through preconditioning, may be necessary. This requires comprehensive understanding of the geology, and its interwoven relationship with geotechnical parameters, and is made more challenging due to limited exposure in block cave mines. Limited mine development throughout the cave volume equates to a heavy reliance on drilling data in terms of observations, modelling of the mine geology, and collection of geotechnical data. This translates as increased uncertainty of geological and geotechnical models and has potential to impact significantly on the ability to make informed decisions in the design and operation of the cave mine.Modelling of cave propagation behaviour requires a complex, coupled system of draw of material, flow of material through the cave stocks, and propagation of the cave-back assisted by autogenic stress-related breakage of the rock mass, manifested as seismicity. The role of geological features in the process of cave propagation is not well understood and requires evaluation on a mine-specific basis, given the diversity of geological controls/settings of ore deposits and local variability of stress fields.Seismic monitoring systems can elucidate key geological features and domains, as heterogeneous seismogenic activity is observed ahead of the advancing cave-back. The observations made from analysis of seismic monitoring data may have potential to be used as a validation tool for numerical modelling of predicted cave behaviour in similar geological settings (eg next lift/panel).Understanding of the geological structure, at all scales, is critical to optimise the design and operating decisions made in a block cave operation. At present, intermediate-scale structure, anisotropy, mineralogy and model uncertainty may be neglected or under-represented despite their likely significant role in the mechanisms of cave propagation.Insights from an analysis of the Ridgeway Deeps block cave mine are discussed in this paper.CITATION:Murphy, T, Webster, A and Chitombo, G, 2016. Beyond rock mass characterisation – the impact of geology on block cave mining, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 861–872 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By F. W. Lee

This paper purposes to outline briefly results of seismic measurements made in the vicinity of blasts in a mine and in open-quarry operations. It endeavors to examine the amplitude and frequency of such vibrations as influenced by the loading, geology, and distance from the source and includes comments on factors that may index the destructiveness of a vibration and a method for measuring the stresses produced. There seems to be no simple mathematical analysis of the transmission of seismic energy through the ground, and experimental observations are at present most feasible. SEISMOLOGIC INSTRUMENTS Instruments developed by the Bureau of Mines for recording ground vibrations from quarry blasting comprise a new type of seismometer, oscillators, and a recording oscillograph. The seismometers respond to vibrations reaching them through the earth and transmit their characteristics by electric current to the oscillograph, where they are recorded by a beam of light on a moving strip of sensitized photographic paper. The seismometers are so constructed that their sensitivity to earth vibration can be controlled, thus keeping the amplitude of the recorded wave within bounds on the paper. Each instrument has been calibrated against vibrations of known intensity and frequency so that correction factors are known for the idiosyncracies of each unit. Moreover, each seismometer is calibrated in the field for its particular sensitivity setting at each blast. By these controls the actual movement of the earth due to vibrations of one ten-thousandth of an inch can be accurately measured.

Jan 1, 1936

The Greymouth Coal field is situated on the West Coast of New Zealand's South Island and has been mined for coal for more than 120 years. The area covered in this paper is within the Rapahoe Sector of this field and contains >200 million tonnes of low ash, low sulphur, bituminous rank coal. Paper No 6, presented to the 19th Annual Conference of the New Zealand Branch of The Australasian Institute of Mining and Metallurgy in Christchurch in August 1985 by R G Bowman, explained 'A Geologist's View' of the 'Economic Potential of the Greymouth Coalfield', and describes previous geological assessments of the Rapahoe Sector.

Jan 1, 1989

THE treatment by chlorination of the Mount Morgan Gold Mining Company's ores was first accomplished, early in 1886, by a works having a capacity of 25,000 tons per annum. Shortly afterwards another works was established, capable of dealing with 50,000 tons per annum. The extraction of gold was originally successful and satisfactory, but running expenses were high, averaging £2 19s. 6d. per ton of ore treated. These works were believed to be the largest chlorination pJants in the world at that time. As might have been expected, the mechanical details and chemical process had not been perfected, and, moreover, both works were hurriedly built, and operating expenses were not then considered of such prime importance, as the ore at that time was of very high grade the large quantities of low grade ore since dealt with not being then considered, since the bulk of it was not even known to be in existence.These two works consisted of lock-breakers, high speed rolls, screens, elevators, &c., for crushing; a large number of small handrabbled reverberatory furnaces for roasting; one-ton chlorination barrels and three-ton leaching vats for chlorination.

Jan 1, 1910

By B Murphy, A Uliana, P STrgio de Oliveira, G Ara·jo de Souza Franco, T Miettinen

Outotec has performed numerous research and development projects and various surveys in the study of reverse iron ore flotation. Over the past four years their TankCell-70 and TankCell-160 flotation cells at the Germano concentrator of Samarco in Brazil were extensively surveyed. These surveys have revealed some extreme operating conditions in reverse iron ore flotation and are the subject of this paper. Some of the findings include large variations in the content of solids in the various flotation stages. At the bottom of the cleaner cells, the content of solids by weight reached over 60 per cent, whereas at the bottom of the scavenger cell this was less than 50 per cent. Froth carry rates were also significantly different in the various flotation stages. In the case of coarse material, the scavenger cells operated at a froth carry rate of over 40 t/h.m2. With fine material, however, froth carry rates of less than 10 t/h.m2 were measured. High froth carry rates caused significant changes in the residence times at Samarco. In the rougher cells, the fifth cell had more than double the residence time of the first cell. This was even more pronounced with the scavenger cells, where the second cell had more than triple the residence time of the first cell. High froth carry rates also caused losses in iron recovery. As a consequence of such findings, it appears that different rules apply in the sizing of reverse flotation circuits compared to direct flotation circuits. Different operating parameters (mixing intensities and air flow rates) must also be used in the rougher, cleaner and scavenger cells in order to optimise the metallurgical performance. Outotec has also been working on a number of new technologies aimed at improving the metallurgical performance of iron ore reverse flotation circuits by increasing froth carry rate and decreasing fine iron entrainment.CITATION:Miettinen, T, Uliana, A, Ara·jo de Souza Franco, G, STrgio de Oliveira, P and Murphy, B, 2013. TankCell flotation at SamarcoÆs Germano concentrators, in Proceedings Iron Ore 2013 , pp 441-444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By W. H. Boyer, J. W. Gabelman

The concept of metal zoning has long been recognized (Spurr, 1907, 1923; Emmons, 1924, 1926; Lindgren, 1933; Rateman, 1950), although it has been considered indistinct for most epithermal districts. The geometric relation of barren zones of hydrother-mally altered rock to ore deposits was emphasized in the work of Lovering (1941, 1949, 1950), Sales and Meyer (1948, 1949, 19501, Burbank (1941, 1950), Schwartz (1939, 1950), and Kerr (1947). Lovering (op. cit.) and Sales and Meyer (op. cit.) emphasized the consistent presence of barren alteration envelopes enclosing individual ore bodies, particularly of the vein type. Schwartz (1950) noted a difference between the distribution of alteration zones described by Lovering and by Sales and Meyer, as compared with those associated with the porphyry copper deposits of the Southwest. The disseminated deposits of the Southwest usually occur within large bodies of altered rock whereas most veins do not. In the following discussion the mineralization process is conceived of consisting of two distinct phases: pre-ore nonmetallic alteration and metallization. In the present investigation the position, size, and shape of all known hydro thermally altered areas and the position, size, and metal type of all known ore deposits were plotted on base maps of southwestern and west-central Colorado (Figure 1). The maps indicate a generally consistent geometric relation between altered and metallized areas. The addition of alteration to the pattern of metal deposits establishes a temperature zoning pattern of much greater clarity than that formed by the epithermal metal deposits alone, and allows a more precise definition of mineral belts. The center of strongest mineralization is indicated to be the area of greatest barren alteration, and metal deposits are grouped about it both under structural control and crudely in response to temperature zoning. The combination of an area of strong alteration and associated marginal clusters of metal deposits is defined as a mineral district. The strong similarity in individual deposits, in groups of different types of deposits, and in the alteration-metallization relation in districts throughout the region implies that a single metallogenic province is represented in southwestern and west-central Colorado. The occurrence of deposits in Tertiary voi-canics indicates a late Tertiary metallogenic epoci., although an early Tertiary epoch is known locally as at Ouray. Patterns formed by mineral districts can be

Jan 1, 1961

By Mario Terceros H., Bengt H. Fellenius

"ABSTRACTFour strain-gage instrumented bored piles were constructed in a sedimentary, dense to very dense, fine to medium sand in Santa Cruz, Bolivia. Two of the test piles were the normally used bored pile constructed with bentonite slurry and two piles were Bauer Full Displacement Pile (FDP). One of each pair was equipped with the Expander Body, an inflatable steel cylinder that on pressure-grouting provides an enlarged pile toe. Head-down static loading test were performed on three of the piles and a bidirectional test was performed on the fourth pile, a standard pile with Expander Body and a bidirectional cell placed immediately above the EB. The latter pile was tested in 3 phases. First by activating the cell, second, by a head-down test, and, third, by a repeat bidirectional cell test. The static loading tests proved the shaft resistance of the FDP pile to be about twice that of the standard bored pile and that the Expander Body more than doubled the toe stiffness. The strain-gage records showed that the standard bored piles had multiple bulges and neckings, which affected the evaluation of the axial stiffness and load distribution of the piles. The testing programme was used for a prediction event with 60 persons, ahead of the tests, submitting predictions of the load-movement curves for the test piles and also a capacity appraised from the curves.1. INTRODUCTIONOn April 23 - 26, 2013, the First International Conference and Seminar on Deep Foundations was held in Santa Cruz, Bolivia under the auspices of INCOTEC SRL, the UAGRM University, and the Bolivian Association of Civil Engineers and Chamber of Construction. To coincide with the conference, a research study on construction and static and dynamic testing of four instrumented bored piles was undertaken. To ""add spice"" to the conference, a prediction event was organized on the test programme. This paper presents the soil conditions at the site, the type and construction of the test piles, the outcome of the prediction event, and the results of the static tests.2. SOIL CONDITIONSGeotechnical studies comprising SPT and CPT tests with routine laboratory analysis were performed on recovered soil samples. Three SPT boreholes were put down at three of the locations of Pile TP1, TP2, and TP3, at 5.0 m distance from each other. The SPT procedure consisted of manual hoisting of the weight by three crew members pulling on ropes over a pulley supported by a tripod and letting the weight fall by gravity. The groundwater table lies at 3.5 m depth.Figure 1 shows diagrams of the SPT N-indices and the distribution of water content in the three boreholes. The SPT-indices show the soil density to be compact. The average water content is about 15 %, plus-minus a few percent."

Jan 1, 2014

By J. F. Lupo

Leaching operations combine both metallurgical and hydraulic processes to extract metals from the ore heap. In the design of leaching operations, metallurgical tests and simple hydraulic tests are often conducted to define operational parameters such as leach cycle time, application rate, lift height, and effective leach area. While metallurgical constraints are often the primary focus on leach facility design, the hydraulic factors are also critical to the overall success of the operation. Some of the hydraulic factors that are known to impact solution flow through heaps include: • Ore physical and hydraulic properties, • Variation in ore properties under heap loading, • Ore mineralogy and its susceptibility to chemical and/or mechanical degradation, and • Heterogeneities within the heap. This paper presents a discussion on hydraulic factors that may impact the effectiveness of leaching operations. In addition, methods are presented which may be used to assess flow conditions within active and inactive heaps.

Jan 1, 2000

By Michael J. Lord, Richard H. O. Wagner

"The technologies used in the mineral processing of ores are being increasingly applied to the identification and remediation of metal contaminated industrial, military and landfill sites. The objective of mineral processing treatment of contaminated site material is to restore the value of the land and to concentrate the contaminants into a very small volume of separated material which, depending upon its nature, can be further processed, marketed, or sent to a landfill. A systematic characterisation of the site material is first undertaken. Bench and pilot testing follows to evaluate criteria for metal separation. The testing may examine one or more physical or physico-chemical reprocessing methods, singly or in combination, for the remediation of the test samples. These mineral processing tests determine the % metal removal fiom the soil and the contaminants concentrated from the medium. The usefulness of mineral processing testing for site remediation flowsheet design and execution is illustrated by the case studies presented. This paper will present the test results of three case studies: an industrial site decontamination, the cleanup of a small arms firing range, and the reclamation of property within a landfill.INTRODUCTIONEnvironmental legislation and our society’s quest for a cleaner environment has led to the application of mineral processing expertise and technology for industrial site decontamination, military site cleanup and landfill reclamation. Although the required level of decontamination varies between jurisdictions, a site becomes a candidate for decontamination once the contaminant concentrations are found to exceed the Canadian Council of Ministers of the Environment (CCME) Interim Remediation Criteria for soil (decommissioning guidelines) or applicable provincial guidelines. The objective of mineral processing treatment of contaminated site material is to restore the value of the land and to concentrate the contaminants into a very small volume of separated material which, depending upon its nature, can be further processed, marketed or disposed of in a landfill"

Jan 1, 1999

By Luis-Fernando Contreras, Juliano Maran, Richard LeSueur

A risk study was carried out at the Cerrejon coal mine in order to assess the impacts of pit slope failure in terms of safety of personnel and destruction of equipment with economic consequences. Results of the assessment enabled the definition of risk treatment requirements and the identification of key aspects to consider in a risk treatment plan. The approach included the following tasks: (1) Assessment of the total probability of failure (POF) representative of the stability conditions of typical footwall and highwall slopes. For this purpose, stability analyses were carried out to define the Design POF, which accounts for the variability of strength parameters and represents the normal conditions considered for slope design. Strength parameters for highwall slope analysis were derived from borehole data obtained with a geotechnical drilling campaign. The Total POF was estimated through the use of Source Response Diagrams (SRD) in order to incorporate other sources of uncertainty not accounted for, like changes in geometry, variability of rock conditions due to geological or operational factors, changes in groundwater conditions and occurrence of seismic events. (2) Assessment of the consequences of footwall and highwall slope failure on safety of personnel. The assessment was performed through the use of event tree analysis to establish the probability of fatality caused by slope failures, from the Total POF defined in the previous task. This analysis required the evaluation of personal exposure to slope failures. Also, the assessment included benchmarking of acceptability criteria in terms of probability of fatality and the evaluation of options of risk mitigation to comply with these criteria. (3) Assessment of the consequences of footwall and highwall slope failure in terms of economic losses associated with impact on equipment. The analysis included the evaluation of equipment exposure to slope failures, and it was performed through event tree analysis to establish the probability of an economic loss associated to total or partial lost of equipment, from the total POF value defined in the first task. The magnitude of the economic losses was estimated from the costs of damaged equipment, lost production and site restoration. Options of risk mitigation were also examined in terms of economic losses. The risk assessment process applied to the Cerrejón mine showed how the system can be applied to evaluate the consequences of failure in terms of personnel safety and economics and to identify the more adequate risk mitigation options. The system can be an extremely powerful tool in the mine design process and provides the opportunity to rationalize the geotechnical information requirements, once the risk criteria have been defined by management. The main purpose of this paper is to present the process; therefore, the emphasis has been put on the methodology followed rather than on the actual results obtained.

Jan 1, 2006

By William F. Hahn

This report describes an illumination system suitable for use in a slope under construction, Simulator work was performed using actual lighting hardware to verify adequate light levels to meet MSHA proposed regulation (as published in the Federal Register, January 13, 1977). The sequence of operating activities for two different slope driving sites are discussed and lighting requirements are defined for each,

Jan 1, 1981

By The Staff

Introduction For many years the necessity of mechanization of all the underground services in the collieries of the Dominion Steel and Coal Corporation in the Sydney, Pictou, and Cumberland coalfields has been foremost in the minds of those concerned with the engineering and operating policies of the Corporation, and a gradual policy of the mechanization of these services has been undertaken over the years, until nearly all the underground services, except the actual loading of the coal at the face, have been mechanized. Early in 1928, experiments in mechanical loading were conducted which finally culminated in the installation of mechanical loading units in our No. 20 colliery in 1938. This attempt at mechanization of the final underground services proved unsuccessful because the workmen were not ready to accept complete mechanization, and the fruition of many years of study was delayed until the year 1947. During the ensuing years, the engineers and operators of the Corporation had studied the possibility of adapting to conditions prevailing in Nova Scotia mines the many types of loading equipment in use in the United States and Europe. The varied physical conditions which exist in the fields operated by the Corporation rendered it extremely difficult to apply the equipment and technique successfully employed in the United States, and more recently in Europe, and special techniques have had to be devised to meet the need of each individual colliery. Prevailing physical conditions in the Nova Scotia fields find no parallel for mechanization with those of any other part of the American continent.

Jan 1, 1949

By Brian Hart, Hong Zhong, Liuyin Xia, Kyle Douglas

"The application of hydroxamic acid as flotation collectors is fast becoming of significant interest for the selective flotation of oxide minerals along with upgrading oxidised based metal ores and minerals. In the hydroxamate molecule, both O and N atoms in the -CONHOH group are identified as coordination atoms in many complexes and their characteristic structure determines the strength of the chelation complex between the hydroxamate and metal ion. The chelating performance of hydroxamates with transition metals including Cu, Ni, Zn, Fe, Cr, Mn and Co, the alkaline-earth metals (Be, Ca) and heavy metal (Pb) has been studied. Cytec has developed and patented a range of alkyl hydroxamates as flotation collectors for oxidised base metal sulphides, metal oxide minerals and precious metals. This paper introduces two new structures of hydroxamate collectors (Cyclohexyl and 4-tert-butylbenzoyl hydroxamates) and evaluates their characteristics relative to alkyl and benzoyl hydroxamates. Laboratory small-scale flotation tests were conducted with ilmenite and wolframite. The use of 4-tert-butyl benzoyl hydroxamate resulted in a best flotation performance for ilmenite. A relatively low cyclohexyl hydroxamate dosage was required in the flotation of wolframite to obtain comparable results to the alkyl and benzoyl hydroxamates. It is also shown a significantly improved flotation performance with 4-tertbutyl benzoyl hydroxamate in the flotation of ilmenite plant ore in comparison to the oleic acid or fatty acid collectors typically used for ilmenite flotation.INTRODUCTIONHydroxamic acid has been reported as an effective collector in small-scale flotation tests for a wide variety of oxide minerals and ores including copper (Lee et al., 1998, Lee et al., 2009), iron (Quast, 2000), tin (Sreenivas and Padmanabhan, 2002; Wu and Zhu, 2006), tungsten (Marinakis and Kelsall, 1987; Xia et al.,2004), and rare earth metal minerals (Ren et al., 1997; Pradip and Fuerstenau, 1991; Assis et al., 1996; Pavez et al., 1996; Zheng et al., 1996; Chen et al.,2005).As part of our previous research project, a selected suite of hydroxamic acid collectors including fatty, aromatic and modified hydroxamates (naphthoyl, cyclohexyl, benzoyl, octyl, 4-tert-butyl benzoyl, salicylic hydroxamates) were tested in order to examine their potential for recovery and selectivity of rare earth minerals. In these tests it was shown that the flotation performance with the hydroxamate collectors was significantly better than the phosphoric acid collectors on no slimes removed samples (Brian, et al., 2014; Liuyin, et al., 2014 and unpublished internal technical reports). Furthermore the tests revealed that for most of the hydroxamate reagents tested, their dosage requirements to achieve recoveries at the same levels was less than that for the phosphoric acid collectors. Recovery of both La and Ce was significantly better for the salicylic hydroxamate and that Nb, Y and Zr recovery were favoured by the octyl and benzoyl hydroxamates (Brian, et al., 2014; Liuyin, et al., 2014). Comparison among the hydroxamate collectors showed that the flotation and recovery performance of cyclohexyl (CHH) and 4-tert-butyl benzoyl (TBH) was not as good as the other hydroxamates for rare earth recovery."

Jan 1, 2015

By Jurgen te Kook

State-of-the-art for subsidence calculation are stochastical models. Although these models were successfully used all over the world they have their limitations due to the fact that they are not based on mechanical laws. For example the models did not take the rock mass structure and the rock mass characteristics into account. Therefore in a research program the skills of geomechanical numerical models for subsidence calculation were investigated. A case study shows that numerical models which are in principle based on the elastic theory are suitable for subsidence prediction. Due to the principles of these models the results are not sufficient in the case of multiple seam extraction. More extended geomechanical numerical models like FLAC and UDEC were investigated in further steps of the research work. Up to now large area geomechanical models require unrealistic long calculation times if the level of detail is similar to that of small scale calculations. Due to this it was necessary to implement a simplified description of the rock mass structure and characteristics. Different case studies show that this approach is successfull for subsidence calculation by numerical geomechanical models even for multiple seam extraction.

Jan 1, 2008

By John Heilig, Patrick Andrieux

"Near-field monitoring of blast induced seismic vibrations is a practical and useful way of assessing blast field behaviour for diagnosis and optimization purposes. It is also necessary in order to provide the information from which empirical vibration prediction equations, such as the one proposed by Holmberg (11 for example, can be derived. (Strictly speaking, the “near field” extends from the blasthole itself to about one charge length away from it; however, throughout this article, “near field”will.most often refer to the outer limit of this zone, from roughly 0.75 to 1.50 charge length away.) In order to obtain reliable data, proper field monitoring techniques are of paramount importance. Once the data are properly recorded, analysis can be done either in the time domain (describing vibration amplitude vs. time) or in the frequency domain (usually describing vibration amplitude vs. frequency)."

Jan 1, 1995