Search Documents

By U. B. Kodukula

Attempts are made to evaluate the feasibility of using a water-injection cyclone for the concentration of iron ore fines. The separation characteristics of clay fines, containing large amounts of alumina and silica, from the iron values are discussed. The effects of critical variables, such as injection water rate, truncated cone diameter, spigot opening and vortex finder diameter, on the performance of a water-injection cyclone in terms of iron, alumina and silica grades; iron recoveries; and alumina and silica rejections are discussed. A set of 16 full-factorial experiments (24) was carried out to gain an understanding of the individual and interaction effects of the variables. The results indicate that classifying iron ore fines containing 63.0% iron, 2.5% alumina and 3.5% silica through a water-injection cyclone can produce concentrates with iron grades greater than 66.0% and alumina and silica contents less than 1.5% and 2.0%, respectively, at different study conditions. The achievable iron recovery values are greater than 88%, and alumina and silica rejections are more than 80% and 50%, respectively, within the specific study conditions. While the truncated cone diameter, injection water rate and spigot diameter influences the alumina rejection to a considerable extent, it is mostly influenced by the vortex finder diameter. The iron recovery and silica rejection values are mostly influenced by spigot diameter and truncated cone diameter. The effect of injection water on the concentration characteristics depend on the prevalent truncated cone diameter and spigot diameter conditions.

Jan 1, 2008

By P Staples, G Lane, S Morrell

The design of semi-autogenous grinding (SAG) mill based comminution circuits for the treatment of competent ores, similar to those at Geita and Boddington, involves the same process of sample selection, test work, data analysis and data modelling/interpretation as that used for 'average' competency ores. However, over the past couple of years a number of issues have arisen that are common to the design of circuits for the comminution of 'highly' competent ores. The impact of these issues on project viability is generally more pronounced when treating hard ores than average to soft ores due to the greater impact on capital and operating costs. The issues encountered have included: standard test procedures have been modified; test equipment has worn or been damaged; different procedures yield different data and varying interpretation; and modelling and empirical calculations have been based on poor benchmarks, or used incorrectly in the case of JKSimMet, yielding misleading outcomes. The purpose of this paper is to present, discuss and clarify some of the issues associated with conducting test work and designing comminution circuits for the treatment of 'highly' competent ores in order to reduce thelevel of conflict arising from interpretation and application of test work data. Specifically, the issues associated with the bond crushing (impact) and rod work indices measurement, the various SAG mill specific energy tests, and the interpretation of the resulting data will be discussed in the context of case studies.

Jan 1, 2009

By D Wiseman, D Weedon, T Akroyd

Models of the size specific processes of particle collision, attachment and detachment have been combined in a form suitable for analysis of a full-scale flotation plant. The model is based on a first principal approach to particle collection by bubbles. Parameters considered include particle size, bubble size, particle contact angle, energy dissipation, entrainment and froth recovery. Using data structures configured within an Excel spreadsheet using æLimn: The Flowsheet ProcessorÆ, the model has been incorporated into a description of the individual cells within a simple roughing and cleaning flotation circuit. Simulated feeds of varying particle size distribution, feed tonnage and varying mineral hydrophobicity representing different mineral phases are presented to the model to produce predicted final concentrate grades and recoveries. Practical techniques for measuring many of the parameters included in the model are now becoming readily available. However, relating the terms included for contact angle, energy dissipation, entrainment (ie water recovery) and froth recovery to measurable parameters in operating plants remain as continuing challenges for research.

Jan 1, 2004

The sulphides can be arranged in a series determined by the relative amounts of ionic and covalent bonding present. This series is similar to the paragenetic series common to most sulphide ore deposits. Investigation of the surface tensions of the corresponding heavy metal iodides by the maximum bubble pressure method throws some light upon this relationship. It is shown that the surface tension of molten iodides decreases as the chemical bonding within them becomes more covalent. These results are interpreted in terms of the constitution of the melts, and are extended to cover the case of sulphides in solution in a silicate melt. It is concluded that sulphides tend to lower the surface tension of silicate melts and that this tendency becomes greater as the bonding within the dissolved sulphide groups becomes more covalent. A possible relationship between this conclusion and the origin of paragenesis in sulphide ore deposits is indicated.INTRODUCTIONIt is well known that the order of deposition, or paragenesis of sulphide minerals is remarkably similar in hypogene ore deposits throughout the world. This widespread similarity points towards the operation of some fundamental process which must be intimately connected with -the genesis of these ores. A correct interpretation and understanding of the causes of paragenesis in sulphide ore deposits would shed much light on the origin of these deposits.In Table 1 a simplified paragenetic series for sulphide minerals is presented. In most cases, only the most important sulphide of any particular element has been included. The object of this procedure is to simplify the following discussion. Furthermore, it should be realized that this series is only a generalization and that exceptions and reversals of position are quite common. Especially does this...

Jan 1, 1956

By S. J. Broderick

[The term "nonmetallic minerals? as commonly used is the mining industry, refers to those minerals of industrial importance that are mined essentially for uses other than for the metals contained. The field comprises several hundred rod minerals of industrial importance, of which 70 have can adequately described in the textbook Industrial Minerals and Rocks. A few o f the more important nonmetallic products are sand and gravel, salt, phosphates, clays, refractories, limestone, and cement materials. Some of the minerals, such as bauxite and pyrolusive, have both metallic and nonmetallic applications, but in this report only the nonmetallic mineral phases are considered. In the organic field of nonmetallics only coal is considered, as, the others - petroleum, natural gas, natural bitumens, and hydrocarbons - are of no importance in water softening.]

Jan 1, 1941

Collecting the clay fraction of active stream sediment from a flowing stream for geochemical analysis i a difficult process. One either takes a sample of dry fine-grained sediment from the stream bank (dry weather and dry sample are uncommon in parts of New Zealand and Tasmania), or dredges up a sample of sand and mud out of the stream.The latter method produces a soggy ample bag full of mud and sand, with varying amounts of gravel, depending on the size of the stream. The water can be filtered from such a sample by means of a Buchner filter funnel, but is difficult to obtain a vacuum in the bush. This problem can be solved by using a small hand- queeze bellows such as used in priming petrol pumps on outboard petrol motors. The common laboratory hand bellows is not powerful enough.A 70 mm diameter two-piece polythene Buchner filter funnel (Fig. 1) can be used. A length of rubber tubing is fitted around the inlet valve of the hand bellows and this valve is then jammed into the pipe at the bottom of the filter funnel (the polythene pipe may be trimmed with a knife to fit over the inlet valve of the bellows). The vacuum is generated and maintained by squeezing the hand bellows.The technique of collecting a sample of the clay fraction is to dredge a sample of the fine-grained active stream sediment out of the stream with a container, such as a plastic mug. The sample is agitated to get the clay fraction into suspension and the muddy suspension is then decanted into the Buchner funnel. The desired clay fraction is obtained as a thin film on the filter paper.If the "fines" are also required, a filter of nylon bolting cloth (stretched across the mouth of a short length of 80 mm diameter polythene pipe and attached by rubber bands or a concentric polythene pipe) can be placed over the mouth of the Buchner funnel and the whole sample of stream sediment...

Jan 1, 1969

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphonic acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphoric acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937

By L. L. Lacerda, A. J. Blair

The Wolf Creek Upper Narrows Tunnel (Upper Narrows Tunnel) is one of the first major highway tunnel in the United States implementing the use of spray-on membrane for purposes of constructing a double-shell drainage solution between an initial shotcrete lining and a final cast-in-place concrete lining (Figure 1). In the case of the Upper Narrows Tunnel the primary membrane is constructed with a spray-on product manufactured by Degussa, namely Masterseal® 340 FA (MS 340) that has been utilized previously in other tunnel projects. Shotcrete-like in application, but differing in physical properties, MS 340 is now outdated, and is succeeded by Masterseal® 345 (MS 345), a nearly identical product, with improvements in material properties. Tunnel project histories utilizing either MS 340 or MS 345 are discussed and summarized with regard to the respective motives for prompting spray-on membrane selection and the realized benefits resulting from spray-on membrane construction. With an emphasis on the Upper Narrows Tunnel, project summaries discuss details of the aspects of design for spray-on membrane construction methodology as opposed to conventional sheet membrane construction methodologies. It is anticipated that experience gained during the construction of the Upper Narrows Tunnel with respect to other tunnel projects that have utilized spray-on membrane will be of use for future tunnels employing spray-on membrane in drainage solutions.

Jan 1, 2005

By Andrew Port, Ali Ghandeharioon

Nonlinear seismic deformation analyses using the finite difference program FLAC were performed for a wastewater treatment plant to estimate foundation displacement and performance of two proposed trickling filters during the 2475-year event design earthquake. The effective stress based constitutive model UBCSAND, which captures the cyclic behavior of both the “sand-like” and “clay-like” materials, was used to model the dynamic response of the soil strata. Dynamic analyses of the site indicated that in absence of ground improvement or deep foundations beneath the proposed trickling filters, those structures would undergo horizontal displacements in excess of 1 m and short-term differential settlement gradient of about 400 mm over 50 m as a result of seismic and post-seismic settlements. Three mitigation options were considered for limiting the seismic displacements and differential settlement gradients of the proposed trickling filters. These alternatives include vibro-replacement stone columns, vibro-replacement stone columns plus supplementary cutter soil mixing (CSM) configurations, and pile foundations. Various layouts for each mitigation option were considered including the lateral extent of the ground improvement, CSM walls and pile spacing. Seismic horizontal and vertical displacements of the proposed structures as well as post-earthquake consolidation settlements due to dissipation of excess pore water pressures in soil layers were assessed in all the analysis alternatives. The analyses indicate that all the alternatives considered have the potential to provide a comparable level of seismic and post-seismic performance. However, for similar performance levels, the ground improvement options need to extend well beyond the edges of the proposed structures, while the piles can be limited to just beneath the footprint of the structures. INTRODUCTION Annacis Island Wastewater Treatment Plant (AIWWTP) is owned and operated by Greater Vancouver Sewerage and Drainage District and services a population of approximately 1 million people in Vancouver, British Columbia. Wastewater is generated by residential, commercial, and industrial sectors and the treated effluent is discharged to Annieville Channel of Fraser River on the south side of Annacis Island. AIWWTP is located on a 51-hectare site and was commissioned in 1975 as a primary treatment plant, but has had two major expansions to meet the population growth needs, and to improve the treatment process efficiency through the provision of secondary treatment of the liquid stream. The current expansion includes construction of additional solids contact tanks and secondary clarifiers. Future expansions include the construction of proposed additional trickling filters. New expansion structures are required to be designed for post-seismic operation after the 2475-year event design earthquake.

Jan 1, 2018

By Gilles Rousset

This paper presents laboratory experiments conducted on hollow cylinders samples. The advantage of such a geometry is to approach in situ conditions around cylindrical openings (lined galleries, boreholes, ...). Many authors have been interested in this kind of problem, especially for borehole stability applications (for references see Guenot 1987). However, as long as we know, time-dependent behavior has not been well studied. For this purpose, we have set up two different types of tests on a deep clay : - Quick unloading test, to assess the influence of unloading rate on mechanical response and the failure modes. - Creep and relaxation test, to compute the time dependent overall deformation of the hole wall as well as to plot long term convergence-confinement pressure curve. The experimental results are then compared with those given by a theoretical model developed in our laboratory, well fitted with the tested material.

Jan 1, 1989

By Thomas W. Camm

This study was done to evaluate the costs of various dumping operations at waste and spoil piles. It has been theorized that accidents associated with dumping operations might be reduced by short-dumping rather than edge-dumping, but many operators have been reluctant to use short-dumping because they believe it is not as cost effective as edge-dumping. To evaluate this perception, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health reviewed the costs of various dumping methods at waste and spoil piles. The study found that overall cost differences between the two methods were not significant in most cases. However, while overall cost differences between the two methods appear small, capital costs could be more significant when short-dumping if numerous dump sites are used concurrently. The choice of which method to use should be based on considerations of the safety of dozer and truck operators.

Jan 1, 2000

By R. L. Guerguerian

Nowadays, most grinding mills driven by a wrap-around ring motor are operating successfully. Some of the earlier problems could be attributed to the lateral stiffness and stability of their bearings. As a result, modifications to the bearings included the rearrangement of the shoes, or the addition of more shoes, closer to the horizontal centerline. This technical paper reports a study of the effects of bearings on the lateral stiffness of grinding mills driven by a wrap-around ring motor. The discussions cover the design of the four shoe trunnion bearings and examine the effects of the angular location of the shoes.

Jan 1, 2000

Industrial minerals enjoyed a fairly successful year in 1978, despite the sluggish economy, inflation, and environmental restrictions. A glance at US Bureau of Mines statistics shows that, in general, production of industrial minerals increased from + 1% (salt) to as much as 26% (sulfur, other than Frasch or recovered). A few industrial minerals showed a decline; fluorspar production, for example, registered a 23% decrease in 1978 from 1977 due to the closing of three domestic mines. Bromine, natural sodium sulfate, Frasch sulfur, and vermiculite also had production decreases of 2-6% in 1978.

Jan 5, 1979

By H. A. Dierks

Implementation of the joint Federal-State control program established in 1955 to cope with the mine water problem in the Pennsylvania anthracite region is described in this report. The increasing severity of the water problem in the anthracite mines has necessitated major adjustments as this continuing program has progressed. Since 1941 the Federal Government has recognized the mine water problem as an important factor in the worsening economic condition of the anthracite region by initiating scientific and technologic investigations and establishing the Anthracite Flood-Prevention Section in the Bureau of Mines in 1948. On the basis of comprehensive investigations and studies, the results of which were published in numerous reports and bulletins, the Anthracite Mine Drainage Commission of the Commonwealth of Pennsylvania formulated a plan that served as a background for legislative action in 1955, resulting in Public Law 162, 84th Congress (Act of July 15, 1955 (69 Stat. 352; 30 U.S.C. 571-576)), for the Federal Government, and Act No. 82 of the General Assembly, July 7, 1955, for the Commonwealth of Pennsylvania. The report covers 29 mine flood control projects approved and executed in implementing the aforementioned legislative acts. Essential engineering and cost details for each project are given, together with an evaluation of the effect that the installed facilities have on alleviating the mine water problem as it concerns individual mines and the anthracite industry as a whole.

Jan 1, 1962

By A. G. Eccles

Western Mines' milling circuit produces three concentrates (copper, lead and zinc), with the tailings being disposed of at the bottom of Buttle Lake. In view of the mine's location and the method of tailing disposal, a comprehensive pollution control program has been in effect since start-up. Changes -in the ore over the past few years have required the use of increasing quantities of sodium cyanide in order to effect a good copper-lead separation. This led to the use of alkaline chlorination for destruction of ?residual cyanide and precipitation of dissolved copper contained in the tailing effluent. The development of Western Mines' alkaline chlorination plant is discussed in detail, including initial test work and the evolution of procedures leading to the present operation. The current monitoring program is also reviewed.

Jan 1, 1977

By Warren L. J

The effectiveness of shear-flocculation as a method for upgrading simple mixtures of ultrafine (1-11 \lm) scheelite and garnet was evaluated. Statistical methods were used in the design and analysis of the main test program.The stirrer speed, stirring time, and initial weight ratio were all found to have significant effects on both the recovery and grade of the floes produced. The particle sizes also had an effect on the final grade. There were several important interactions between factors which also affected the results. Optimum conditions for shear-flocculation were established, and under these conditions about 80 per cent of the scheelite could be recovered at a grade which depended on the composition of the starting mixture. Starting with mixtures containing 10 and 50 per cent scheelite, the best final grades were between 20 and 50 per cent and between 70 and 90 per cent respectively, the actual value depending on the particular combination of particle sizes.

Jan 1, 1977

A series of gas inrush events occurred during development at Grosvenor mine resulting in exposure to elevated levels of methane at the production face. A total of 22 gas inrush events occurred releasing between 15 and 130 m3 of methane during each event. The presence of an undrained seam in the immediate floor, geotechnical characteristics of the floor, and the stress environment all contributed to these dynamic floor events, while the geological characteristics of the seam below, such as the seam thickness and ash content of 75%, prevented effective pre-drainage. However, events only occurred in headings mined parallel to the principal horizontal stress direction. In cut-throughs (C/Ts) perpendicular to the principal stress direction, no events occurred, and higher methane levels were observed at the production face.

Jan 7, 2020

By T N. Little

The author contends that geoscience is presently under-utilised in the rock fragmentation by blasting process. Before we can set standards in this area, the following is required: mine geologists need to gain a better understanding of the blasting process and the blasting team needs to obtain a better appreciation of geology. Both groups need to be informed of what can be done to improve blasting outcomes, why it is necessary and how it can be achieved. By working closely together, both the geoscience toolkits and blasting expertise can be applied and focused on priority blast sensitive issues, with potential to improve mine economics and safety. Finally, and ideally, mine geologists need to take a leadership role in raw rock mass data collection and data management, and invited to take an active role in rock mass related behaviour data collection, integration and presentation.This paper attempts to provide insight into all these prerequisites for setting a new standard for collaboration and mutual learning in this strategic opportunity area. The potential for blasting to leverage downstream processes is highlighted. Blasting objectives and blast design principles are introduced along with the required rock mass related inputs. Some hazardous geological materials and environmental conditions are described, along with how they can affect operational complexity.Four case examples are used to illustrate the need for closer liaison between geology and blasting professionals. The first related to grade control blasting, aims to demonstrate how a blasting geology approach can add significant value. Case example two demonstrates how geological models and bench face analysis can assist with fragment control. The third and fourth case examples involve an overview of two case studies where timely geological and geotechnical knowledge input and intervention into blasting activities may have reduced losses due to blast initiated open pit slope collapses.CITATION:Little, T N, 2017. Geoscience input into blasting operations – let’s set a new standard, in Proceedings Tenth International Mining Geology Conference 2017, pp 375–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Charlie Yates, Max Ramey, Kurt Nielsen, Michael Hardy

The Yankee Gulch sodium minerals project (YGP) is a solution mining project operated by American Soda. The mine operates on a federal lease administered by the U.S. Bureau of Land Management (BLM). Commercial operations began in November2000. In 1964, Irv Nielsen discovered nahcolite mineralization where the YGP pilot plant is now located near the Piceance Creek in Rio Blanco County, Colorado (Nielsen, 1969).Development of the project accelerated after Williams Corp., of Tulsa, OK, joined with American Alkali in1996 to form American Soda. Pilot testing by American Soda led to commercial permitting, plant design, construction and startup. Figure 1 shows the location of the Yankee Gulch leases and the location of the upper and lower plant sites.

Jan 1, 2003