Search Documents

By S. Coats, G. Norton, A. Benham, P. Ková

The Aynak copper deposit, located 30 km south of Kabul in Afghanistan (Figure 1), was discovered by Soviet geologists in the 1970s. Extensive exploration undertaken in the area between 1974-80 included several hundred boreholes, seventy trenches and nine exploratory adits. This work identified a “drill-indicated resource” of 240 Mt at 2.3% Cu (ESCAP, 1995).

Jan 1, 2007

By L. T. Stanley

A method is described whereby the behavior of the front is approximated when gas is injected into a thick reservoir having reasonably homogeneous properties. The method is applied to the Abqaiq field of Saudi Arabia. The producing member is the Arab-D, a high-permeability calcarenite which has no continuous betlding planes. Field performance indicates the injected gas to be partially miscible with the reservoir oil because gas volume factors experienced are lower than those predicted by the gas law. Eqlrilibril~m calculations confirnz ihis and also show that the volume factor may vary appreciably, depending on the relative quantities of oil and gas in contact in the reservoir; consequently, volutnetric balances are made for the purpose of determining the behavior of the gas volume factor during injection history. The effect of gravity segregation on position and shape of the gas front is approximated by dividing the producing section into three zones vertically and tracing the movement of the average interface in each zone, with counterflow of oil and gas taking place betweell zones behind the front. This results in a gas front that advances more rapidly along the top of [he formation than along the base, producing an "umbrella" effect in cross section that becomes more pronounced as the front progresses. The calculations cover the gas-injection period of Abqaiq field history through 1958, and the position of the gas front is plotted at one-year intervals. Finally, some comparisotls between the calcrlated fronial position and the gas-oil contact as Measured by neutron logs are made. INTRODUCTION Fig. 1 is a structure contour map of the Abqaiq field. For analytical purpcses, the field has been divided into two areas designated A and B, as shown on the map. Gas injection into Area A was begun in early 1954 into two wells located near the crest of the structure on the north-south axis of the anticline. During the period covered by this paper, the average injection rate has been 122 MMscf/D with a maximum sustained rate of 160 MMscf/D. The reservoir pressure has been maintained at 2,450 psig since start of gas injection. The reservoir originally was undersaturated but, prior to pressure maintenance, the pressure was drawn below the bubble point in most of the Area A section, creating an in-place free-gas saturation of 8 per cent at the crest of the structure. The average critical gas saturation is 13 per cent established by laboratcry core tests. That the entire reservoir remained below critical gas saturation prior to gas injection is borne out by the fact that none of the crestal wells have exhibited high gas-oil ratios during production history. The Area A reservoir is a carbonate section about 200-ft thick having average porosity and permeability of the order of 22 per cent and 500 md, respectively. The productive horizon is the Arab-D member of Jurassic age and is encountered at an average depth of

By Richard W. Bayley

The Atlantic City district encompasses several districts and has been previously called by different names, e.g., Atlantic gold district, Atlantic City-South Pass mining district, and Sweetwater mining district. The district is located in a terrane of folded and faulted early Precambrian metamorphic rocks which lies near the south end of the Wind River Range in Fremont County, Wyoming, Historically it is a gold district of little production, but today is an iron district of considerable importance. Gold was discovered in placer deposits about 1842 and in quartz-arsenopyrite veins about 1867, after which there occurred a mining boom lasting a few years. Minor, intermittent gold production from placers and lodes has continued to date, but the total production has probably not exceeded a few millions of dollars. Past lode mining was generally shallow ( in the oxidized zone), the deepest about 3 60 feet. The deeper, less oxidized and sulfide ores on the same lodes have not been explored. They appear to hold the only hope for future gold mining. Sedimentary iron-formation, similar to the Lake Superior taconite, occurs in the northern part of the district. Locally, where the ironformation is thickened by folds and faults, sufficient tonnages are present to be minable, as at Iron Mountain, where the U.S. Steel Corporation produces about 1.3 million tons of iron-ore pellets annually. Exploration of the iron deposits began in 1954, and the first ironore pellets were shipped to Provo, Utah in August 1962. Indicated reserves of iron-formation (about 30 per cent Fe) are reported to be about 300 million tons.

Jan 1, 1968

By D. Rendini, R. D. Gutridge

INTRODUCTION Gwinnett County, Georgia, is a part of the rapidly expanding metropolitan Atlanta Georgia area. Located approximately 48 km (30 miles) northeast of Atlanta, Gwinnett County has a current population in excess of 600,000 and is projected to reach a population of 1,200,000 by 2025. As a part of the County’s master plan to supply drinking water for the expanding population and to increase system reliability, the Gwinnett County Public Utilities Department undertook the Shoal Creek Raw Water Intake and Pump Station Project. Figure 1 shows a vicinity map for the project. Prior to construction of the Shoal Creek Raw Water Intake and Pump Station Project the County had a single raw water intake to feed water from Lake Sidney Lanier (Lake Lanier) into a filter plant for processing into potable water. This project together with a newly constructed water filter plant provides Gwinnett County additional capacity and system redundancy to prevent interruptions to the drinking water supply. Lake Lanier is a man made reservoir with over 800 km (500 miles) of shoreline and was constructed by the Army Corps of Engineers in the 1950s for hydro electric power generation, flood control, and navigation benefits for the Chattahoochee River. Over time, Lake Lanier has become an increasingly important source of drinking water for the metropolitan Atlanta area. This paper focuses on the primary underground construction and lake tap components of the project including a 42.7 m (140 ft) deep pump station shaft 24.4 m(80 ft) in finished diameter transitioning to a 6.1 m (20 ft) finished diameter shaft, a3.05 m (10 ft) finished diameter by 19.8 m (65 ft) deep intake shaft constructed in an average of 21.3 m (70 ft) of water, and a 190.5 m (625 ft) by 3.05 m (10 ft) finished diameter modified horseshoe tunnel connecting the two shafts. This raw water intake system, in conjunction with the incorporated pump station with 8 pumps and dual1,829 mm (72 inch) pipelines, provides a system capacity of 1,091,062 m3/day(240 MGD) to two water filter plants and is expandable by the addition of pumps to1,500,210 m3/day (330 MGD). Parsons provided design and construction management services for the project. The $29.6 million contract to construct the project was awarded to W.L. Hailey &Company. Notice to proceed was given August 6, 2001 and substantial completion was achieved on January 20, 2004. Value engineering changes adopted for the project contributed to completing the project at a final cost of $28.8 million.

Jan 1, 2005

By Floyd G. Anderson

A study was made of the effectiveness of dust-control methods being employed in connection with continuous-mining operations. Airborne dust exposures of workmen and dust loadings of return air were determined for six types of continuous-mining machines. The conditions required for control of dust exposure are summarized and include ventilation of the working face by an exhaust system. Return-air dust loadings ranging up to 13 pounds per hour are reported.

Jan 1, 1963

By William H. Waggaman

The United States not only is the largest producer of phosphate rock but also manufactures and consumes greater quantities of phosphate products than any other country. New and expanding uses will increase even further the demand for this basic raw material. Only a small proportion of the total quantity of phosphate rock mined and marketed is consumed directly in a raw or unprocessed state; the vast bulk is chemically treated and converted into [ertilizer] and a wide variety of finished products that play a vital role in [r] national economy. Three fundamental methods are employed in decomposing phosphate rock. 1. Reduction by carbon at high temperatures. 2. Treatment with one or more acids. 3. Calcination or fusion with silica, sodium salts, magnesium minerals, or small quantities of phosphoric acid.

Jan 1, 1960

By A Marton

Concerns with crest losses have seen changes to a number of design and operating parameters to retain the integrity of the wall and the berms of the Kidston Gold MinesÆ Eldridge Pit. Until trials began in 1999 most final wall designs utilised large diameter blastholes up to the presplit row to achieve the wall angle. The berm crests were being lost, wall support requirements were increasing and affecting mining schedules and several fault areas were putting pit access at risk. Standard designs had been determined during the early mining years and while periodic modifications had been made there was a need for major blast pattern revision. This paper traces the development of wall control blasting programs over the years, relating designs to the geology and the evidence in the walls with the theories of the day and includes the recent trials that were conducted in what is a most unforgiving geology. Trials and improvements to ensure the walls were safe were conducted even as the mine neared its economic life. Instrumented monitoring of trials blasts has greatly increased the understanding of the damage criteria and enabled rapid revision of designs. Recent changes included reduction in presplit energy, charge redistribution and use of smaller blast holes for the trim patterns. Determination of a minimum proximity-to-final wall limit for production blastholes, establishment of the correct standoff to berm crests and walls and selective use of presplitting techniques for protecting crests have resulted in cost effectiveness, improved bench crest retention and an overall reduction in visible wall damage.

Jan 1, 2001

By H. A. Watson

This circular, which is a revision and combination of two previous publications,3 4/ presents information on the different types of equipment that may be used to analyze mine atmospheres, with particular reference to the application and limitations of each type. Such information is frequently requested by mining companies, State mining departments, and other agencies concerned with safety in mining who wish advice regarding methods of analysis of mine atmospheres and the equipment necessary for establishing laboratories for that purpose. Since the Haldane-type apparatus is particularly applicable to the accurate determination of carbon dioxide, oxygen, and combustible gases such as methane in mine atmospheres, that apparatus and the method of operation are described in detail. The circular presents results of a critical study of the accuracy attainable with the Haldane-type apparatus in the determination of methane in concentrations of the order of 0.25 percent, by volume. Analytical procedures involved in the other methods discussed are presented in publications referenced in this circular. Information is given also on the various accessory equipment needed in a laboratory for the analysis of mine atmospheres, and suggestions on laboratory design are included. INTRODUCTION 'The analysis of mine atmospheres plays an important part in promoting safety and maintaining safe conditions in mining operations, particularly in coal mining, where the flammable gas methane presents a continuous hazard in Nome mines and may be encountered unexpectedly in others.5/ Methane has been encountered also, often unexpectedly and with disastrous results, in noncoal mines and in tunnels under

Jan 1, 1956

By Fernando Bermejo

La compañía minera Raura ha desarrollado una política ambiental donde se busca el cumplimiento de la normativa ambiental a través del uso de la tecnología que comprende los principios establecidos dentro del diseño racional de procesos limpios. En este sentido, el presente trabajo señala las ventajas del uso del diseño del método HERBER, el cual consiste en una adsorción de los iones cromatos en la superficie de la pirita en el circuito de remolienda medios. Asimismo, este no requiere de un pretratamiento condicional, no afecta la recuperación del zinc, mejora el grado del concentrado y la concentración de iones cromatos después del tratamiento está por debajo del límite permisible establecido por el Reglamento de la Ley General de Aguas.

Oct 6, 1999

By S. X. Shi, M. Tan, Y. Q. Li, D. F. Han, Z. B. Han

Bauxite resources in China are mainly diaspore ore with the characteristics of low ratio silicon to aluminum. In order to obtain high quality of alumina product, flotation process is generally used to extract the aluminum from diaspore ore. Small aeration rate is needed for bauxite flotation, which requires air to be controlled accuracy. In addition, productive froth from bauxite flotation is too sticky to effects froth transportation. Air-forced XCF/KYF flotation machines are helpful for aeration control, while self-suction GF flotation machines benefits froth transportation. Zhongzhou aluminum plant of China Aluminum Group (Chinalco) uses 7 series of XCF/KYF /GF combined flotation machines to process bauxite. Air distribution, suspension characteristics, froth flow velocity and Al2O3 recovery were investigated, to evaluate the performance of flotation machines in one series and determine recovery contribution of each cell to the entire flotation circuit.The air distribution degree varies from 3 to 4, which is enough for bauxite floatation process. Froth in the tank could flow smoothly with a flow velocity of 2.4m/min. The recovery of the first KYF-40 flotation cell is the largest. Flotation concentrate of Al2O3 is up to 64.29%, the total recovery is about 75%, and the ratio of Al/Si has reached 10.4.

Jan 1, 2015

By Catalin Florin Petre, Elahe Ghasemian Langeroudi, Abdelaaziz Azizi, Éric Proulx, Caroline Olsen, Paul Blatter, Faïçal Larachi, Claude Gagnon

"The recovery of gold from ores is often accompanied by the release of other species in the leach solution. This state of affairs leads to depleted free cyanide levels in the slurry. Therefore, separation and quantification of these cyanicides and free cyanide at different stages of the cyanidation process as well as in waste solutions is crucial to provide mitigation tools by preventing leaching of deleterious metals for environmental considerations.COREM and the research group of Prof. Larachi have been working together on the control of gold passivation and cyanicides during cyanidation for several years. Previously, a first capillary electrophoresis (CE) protocol for the speciation of sulfur and cyanicides (SCN-, Cu, Fe) during cyanidation of gold complex sulfide ores was developed and validated for assessing industrial process water.The separation of zinc cyanide complexes used to be confronted with a number of difficulties due to the weak and/or undetectable cyanocomplexes in formally available CE protocols. Moreover, according to our knowledge, no direct CE protocol exists to separate free cyanide. Therefore, a new study aimed at developing a second CE protocol for the detection and quantification of cyanide complexes of zinc and nickel as well as of free cyanide in the cyanidation process water.To achieve this goal, six common carrier electrolytes such as pyridine, trimellitic acid, 4-methylbenzylamine, sodium chromate, phthalic acid and tris base were studied, using an indirect UV detection method. The best results were obtained using sodium chromate for which all ions were successfully separated and quantified. In addition, the effect of electric field strength, injection volume, electro-osmotic flow (EOF) modifier and background electrolyte (BGE) concentration were examined, while peak height, peak area and noise were considered for optimization.As a result, the new protocol is expected to complete the initial CE protocol by detecting cyanide complexes of zinc and nickel as well as free cyanide. Moreover, analytical determination of free cyanide in the presence of weak cyanide complexes achieved by the new protocol was also compared to conventional titration using silver nitrate solution. This new CE protocol will contribute to applied research and help plants to better understand and eventually control the behaviour of cyanidation circuits."

Jan 1, 2011

By R. E. Ray

Compared to conventional fully ducted axial and centrifugal fan systems, jet fans can offer a number of advantages for control of smoke during fire emergencies and dilution of diesel engine exhaust products in vehicular and rail tunnels. The success of jet fan applications is the result of a balance between the temperature de-rating of the fan, buoyancy forces and the installation momentum transfer efficiency. This paper provides a case study of a unique application of vertically-mounted jet fans in ventilation shafts used to provide both emergency ventilation and pollution control for an overbuild created by the construction of a series of commercial high-rise residential buildings over a portion of an existing passenger rail line. A detailed evaluation of a set of shafts for one building is presented, including a discussion of the calculation methods used to estimate the required jet fan capacity and the results of the subsequent numerical analysis using Computational Fluid Dynamics to simulate the performance of the jet fans during train car fire emergencies.

Jan 1, 2009

By Robert R. Perron

The U.S. Bureau of Mines is engaged in many diverse programs fur improving mine safety. One area of interest to the Bureau is new and improved means for minimizing the hazards of accidental gas ignition or electrical shock should the frame of an off-track machine assume potential above ground. Various means presently used to prevent such occurences are the use of ground fault detectors for phase to ground faults in ac machines, and grounding conductors and diodes in dc machines. In a three phase ac power center, a phase to ground fault may be detected by monitoring the current in the grounding resistor which is required between the power center neutral on the load side of the power center transformer and ground. Another method for detecting a ground fault is to pass the three load conductors through a toroidal core transformer. The phase currents vectorially add up to zero if none of the phases are faulted, and hence the voltage of the transformer secondary is either zero or not zero if one of the phases is unbalanced or faulted.

Jan 1, 1976

By A. R. Dover

The Richmond-San Rafael Bridge is a 6.92 kilometer (4.3 mile) long major toll bridge span that crosses the northern San Francisco Bay in a highly seismically active region. Tutor-Saliba / Koch / Tidewater JV was contracted by Caltrans to conduct a comprehensive seismic retrofit. The JV provided geotechnical planning and quality control services as described herein, under normal oversight by Caltrans. Part of the robust foundation retrofit design included the installation of 26 new, large diameter piles, including eleven 3.81 m (12.5 ft) diameter, cast-in-drilled-hole (CIDH) marine piles that were drilled 9.15 m (30 ft) into the bedrock beneath the Bay, where the water depth ranged up to about 21.3 m (70 ft). These reinforced concrete-filled composite piles have a steel shell permanent casing from the bridge substructure pile cap through the water column and 30.5 to 39.6 meters (100 ft to 130 ft) of marine sediments to the top of rock. This paper discusses construction, inspection (ranging from the QA employed in the planning of the CIDH pile installation methods and equipment to the actual construction inspection required for the routine installation of the shafts), problems that were encountered during construction, and the solutions that were developed and implemented. Inspection, particularly with the usual difficulties in the marine environment, coupled with the difficult and complex bedrock conditions was particularly challenging, and ranged from non-destructive testing to "in-water, inshell" diver inspection. Similarly, the complexities of dealing with both the steel casing "riser" and the associated drilled shaft (rock socket) portion of these composite foundation elements created some unusual issues. The paper also presents important lessons learned from the project.

Jan 1, 2008

"Increasing demand for timely and accurate information about flotation plant performance requires metal accountants to increase the scope and reporting frequency of plant production. This trend has brought in-process inventory estimation at the forefront of metal accounting issues. Such significant in-process inventories can be locked in diverse process equipment (bins, holding tanks, flotation cells, thickeners, pipeline, etc.) or in stockpiles (ore, concentrates, tailings, etc.). Practice has shown that boldly ignoring these in-process inventories or the errors associated with their estimation lead to unreliable metal balances thereby creating confusion in plant production planning and operational performance assessment. To this extent, the characteristics (physical bounds, spatial heterogeneity and residence time) as well as the available measurements (volume, density, humidity, mass, composition, etc.) of each unit/section found in a generic flotation plant are jointly reviewed with respect to the particular metal accounting issues they present. The daily and monthly metal accounting tasks are then reviewed together with possible methods for obtaining reliable inventory estimates including different procedures for end-of month reconciliation.INTRODUCTION Most of the cost reduction initiatives of the mining industry aim at improving capital efficiency and asset utilization. Among the possible paths through which these goals can be achieved are mine-to-metal optimization, real-time plantwide process control (Hodouin, 2011) and knowledge sharing databases (Bascur & Linares, 2006). However, the successful implementation and subsequent monitoring will ineluctably results in an increased demand for timely and accurate information. This more than often requires metal accountants to increase the scope and reporting frequency of plant metal production. A striking example of such scope expansion is the Minas-Rio iron ore project in Brazil (Anglo American, 2013) having a pipeline route of 525 km between the concentrator and the concentrate shipping area. Several other mining companies have also set an increased frequency for their key performance indicators thereby shrinking the metal accounting period from monthly to weekly and daily. Those concurrent trends have brought in-process inventory estimation at the forefront of metal accounting issues. Indeed, as illustrated in Figure 1, improving trading reactivity requires improvements in production planning which strongly impacts the requirements for reliable metallurgical accounting. Furthermore, practice has shown that boldly ignoring significant in-process inventories or the errors associated with their estimation can lead to unreliable metal balances. In other words, since metal balances are the cornerstones of metal accounting, some of the risks associated with important business decisions are linked to errors associated with in-process inventory measurements."

Jan 1, 2014

By J. L. Holman

The Bureau of Mines has extended its previous development of cast Mn-Cu damping alloys to powder metallurgy (P/M) consolidation of alloys containing 55 to 75 wt-pct Mn. Blends of minus 200-mesh elemental powders were compacted cold in directional and isostatic presses. With 1 pct binder, typical green densities ranged between 76 and 80 pct of theoretical when pressing at 30 or 48 tsi. Green strength increased with compacting pressure and copper content. As-sintered tensile strengths ranged to 60,000 psi fox a hydrogen, sintered 60Mn-40Cu alloy, along with 5-pct elongation. Sintered densities ranged between 90 and 96 pct of theoretical. Sintering (a as effective when holding for 1 hr at maximum temperatures of 900° to 1,040` C, dependent on composition. Strength and ductility were considerably lower than for equiva¬lent cast alloys. When aged to the damping condition, alloys containing 60 to 70 pct Mn exhibited >40 pct specific damping capacity (SDC) at 5,000-psi stress, considerably higher than values reported for equivalent cast material. Effects of 1 or 3 pct Sn or Zn additions on SDC and other properties were assessed. Trials were conducted on consolidating rings and gears of the 65Mn-35Cu alloy on industrial-type P/M equipment.

Jan 1, 1979

By S. P. Mishra, G. R. Chaudhury

The adsorption of Cu2+ ions by Penicillium sp. displayed a dual rate, with an initial faster phase followed by a slower one. The adsorption rate increased with increasing pH due to chemical and biochemical reactions. The Cu-loading capacity of the biomass increased at higher initial Cu2+ concentrations. Above 40 degrees C the adsorption rate decreased which may be due to partial hydrolysis of biopolymers which are essential constituents of the cell wall. Adsorption kinetics followed the Freundlich isotherm and the equilibrium concentration that was calculated on the basis of the isotherm matched the observed value well. A series of theoretical adsorption curves were produced using mathematical correlations between the mass transfer coefficient, the Cu2+ ion concentration at equilibrium and at time t. The correlation between the theoretical and observed adsorption rates for different experimental conditions was good. It was concluded that the results from the study were best explained using a mass-transfer adsorption model

Aug 1, 1995

By M. B. McClenaghan, O. P. Lavin, Ian Nichol

"Abstract-Exploration in most areas of Canada has to contend with problems posed by glacial overburden. In many areas exploration for gold has been based on the sampling of tills, frequently by deep overburden drilling, and analyses of heavy mineral concentrates. Notwithstanding the significant role that till geochemistry has played in the discovery of some important gold deposits over the last few years, increased appreciation of the nature of the glacial history and stratigraphy and the character of gold within till has led to the recognition of a number of ways whereby the effectiveness of exploration can be improved upon.In order for till geochemistry to be useful in exploration, a number of conditions must be fulfilled, including:1. mineralization, or alteration halo related to mineralization, subcropping at the bedrock /over­ burden interface; 2.glacial erosion and dispersal of a recognizable signature of mineralization into the glacialsediments; 3, preservation of glacial sediments containing this geochemical component (trace metal or mineral) at positions subsequently selected for sampling (normally drill sites); 4. correct identification of specific till units and associated ice movement history; 5. collection of adequately large and representative samples; 6. appropriate sample preparation and processing; 7, appropriate geochemical analyses; and 8. correct data processing and interpretation.While we have no control over the first two geological conditions, and only limited controlover till availability, we can control the quality and thoroughness of sampling, sample identification, sample preparation, analysis and interpretation. In particular attention needs to be focussed on obtaining a large enough sample to be adequately representative, an unbiased sample must be collected, together with appropriate sample processing, analysis, data processing and interpretation. It is considered that by modifying or extending existing approaches to gold exploration the chances of exploration success can be increased. In particular, analyses of both the heavy mineral and minus 63 ?m fractions of till is recommended because gold in till may occur in different size fractions."

Jan 1, 1992

By Donald F. MacDonald

This report aims to discuss, from the viewpoint of the mining geologist, the bearing of topographic and geologic conditions on cer- tain problems that arose in the construction of the Panama Canal. T+ is published by the Bureau of Mines as a contribution to engineer- ing liters ure because it presents information that shows how geology and topography must be considered by the mining engineer in plan- ning excavations and in removing loose material and solid rock in the safest and most efficient manner. The printing of this bulletin has been approved by the governor of the Panama Canal, as it was impracticable for the Panama Canal to give this information to the general public in any of its publications. The "sword cut" of Goethals and his men did not sever the Isth- mian barrier; it merely clove the hills to a depth of 40 feet above sea level. This cut and the great areas of low valleys at both ends of it have been covered with fresh water to the 85-foot level. This high-level lake held by dams at either end, the 85-foot locks, by which ships enter it, and the dredged approaches from the two oceans constitute the Panama Canal. In the preparation of accurate estimates concerning the cost of large excavations information regarding the geologic conditions, as obtained by a study of natural features, is necessary. Drill holes and test pits will furnish supplementary geologic information, but without a gen- eral knowledge of the geologic conditions it will not be possible for the constructing engineer to answer such questions as the following: (1) What rock units will be encountered in the excavation and in what proportion? (2) What will be the cost of drilling each for blasting (3) How far apart and how deep must the drill holes be to efficiently break the rock of each to the proper size-not too fine nor yet too coarse? In this connection jointing, fissuring, bedding, toughness, and other physical characteristics must be considered (4) How steep will the slopes of the excavation stand, and to what extent will they wash and trench on exposure to the atmosphere? (5) What proportion of the material to be excavated is of such physical character that it may be utilized in any other part of the project, such as in concrete construction, road making, wharves, breakwaters, riprap work, etc.

Jan 1, 1915

By James W. Reil, Douglas A. Anderson, Steven L. Burchell

A total of 26 full-scale production blasts at three sites were extensively monitored with sophisticated instrumentation systems to determine the benefits of "ore. accurate detonators. The new and "ore accurate MS electric Masterdet detonator was tested against conventional detonators to determine any increase in productivity outputs. All blast design parameters between paired blasts were kept as constant as possible with the only difference being the inherent accuracy of both detonator systems.

Jan 1, 1989