Search Documents

By P M. Black, T Itaya

Arc-type volcanic activity has been a major feature of the late Cenozoic geological evolution of the Pacific-Australian plate boundary in the northernNew Zealand region. The time/space distribution patterns of arc-type rocks reflect changes in the nature of the plate boundary as it has evolved. Inception of volcanism began in the north during earliest Miocene times (26 Ma) following ophiolite emplacement and during the next 10 Ma developed into a volcanic arc segment extending south to the present position of the central North Island. The northern part of the arc became extinct about 15Ma ago, but activity continued in the central (Coromandel) part of the arc until about 5 Ma ago. In late Pliocene and Quaternary times volcanic activity has become concentrated in a northeast trending zone which is collinear with the Tonga-Kermadec Arc.   These time/space patterns can be interpreted in two ways. Firstly, if relative plate motion was essentially transform in the region prior to 26 Ma then a small change in the relative plate vectors may have initiated subduction and the associated volcanism. Southward evolution of the arc can then be seen as the straightening and extension of a single arc. Alternatively, the distribution of volcanic rocks can be interpreted as the capture of a relatively short lived arc by southward migration of the dominant Tonga-Kermadec subduction system.

Jan 1, 1995

By R Domotor

Brisbane’s Airport Link is Australia’s largest road infrastructure project, worth a total value of A$4.8 billion. The project is using surface and underground blasting to excavate hard volcanic rock, Brisbane Tuff. This paper tells the story of the most challenging and difficult blast of the whole project: the removal of a remnant pillar of rock (approximately 2250 m3) next to a major arterial road and within 100 m of existing infrastructure including a number of heritage listed buildings, residences and privately owned sensitive receivers. The pillar consisted of a hard rock wall (Brisbane Tuff) between 2 m and 6 m thick, 15 m high and 35 m wide; with in situ precast concrete piles embedded within 1 m of the boundary of the pillar. Orica Australia Pty Limited was contracted by Thiess John Holland, to perform the work in this area, including design, modelling, drilling and loading of the explosives, as well as blast clearance and shotfiring. Access to the area was limited so all explosives and equipment, including the 20 t drill rig, had to be lifted in and out by crane. Due to the nature of the blast, with infrastructure 5 m directly in front of the 15 m high face, there was only ever going to be one chance to get this blast right. This was an extremely complex blast which required the use of a number of different types of packaged explosives, as well as special timing techniques only made possible by using electronic initiating systems. This type of blast is high risk, and is more typical of a building demolition in the urban environment. The blast was fired on the 25 September 2010, and was highly successful. The environmental results for vibration and overpressure were well under the imposed limits, and the embedded concrete piles remained undamaged.

Nov 8, 2011

By J. E. Misiewicz, A Rozendaal

Paper presented at Geofluids '93, held in Torquay, UK, 4-7 May 1993. The tin field consists of a fragment of Lower Proterozoic volcanosedimentary rocks surrounded by granitoids. Almost all the significant deposits are hosted by arkoses and are classified as replacement and space-filling types, with particular styles of mineralisation dominating at different mines. Petrological and geochemical investigation of borehole cores from four centres indicated the presence of a stratified zone 500-600 m thick and continuous over at least 20 km along strike, consisting of pervasively altered clastic arenitic sediments. The alteration is zoned into a grey-green sodic albitised footwall, an 80 m thick sericitised-tourmalinised sulphidic tin zone and a red haematitic potassic hanging-wall. The zoning and the localisation of three cassiterite phases are consistent with the tectonic history and with multiple pulses of stanniferous hydrothermal fluids derived from late differentiates of the granites over a prolonged period. Areas of high fracture density acted as conduits for the fluids, whose initially rapid ascent was retarded by decreasing pressure contrast, limited development of fracturing and/or impermeable shaly arkose to cause lateral spreading and pervasive alteration over a broad, stratified front. Lateral overlapping of local fronts at the various centres suggests a continuous zone, while the many petrological and geochemical similarities point to a shared fluid composition

Aug 1, 1995

By W. Langer

Of the 50 or so most often utilized industrial minerals, more than two thirds are, or have been, produced in the western states of Arizona, Colorado, Idaho, Kansas, Montana, Nebraska, New Mexico, North Dakota, Oklahoma, South Dakota, Texas, Utah, and Wyoming. Some commodities, such as natural aggregate, currently are produced in all 13 states; others such as beryllium and iodine are produced in only Utah and Oklahoma, respectively. Together, the 13 western states make a significant contribution to the US industrial minerals industry.

Jan 1, 2007

By M. W. Robotham, H Wang

removal efficiency is analysed from a stochastic

Apr 1, 1995

By Hanry Guillén

En la Compañía Minera KOLPA, se analizó el comportamiento de sus operaciones unitarias por el período Marzo - Agosto 2016, en el cual se identificaron procesos asociados a los ciclos de perforación y voladura, bajo los términos de variabilidad NO ESTABLES NI SOSTENIBLES, los mismos que ameritaban medirlos, analizarlos, mejorarlos y controlarlos a fin de adoptar decisiones que conduzcan a operar la mina en términos de calidad y excelencia.

Sep 1, 2017

By Michael Karmis

The International Conference on Sustainable Development Indicators in the Mineral Industries(SDIMI 2003) was held May 21-23, 2003 on the island of Milos, Greece. The objective of this international conference was to assist the mining and minerals industries in their global transition to sustainable development. The main theme of the conference was the development, monitoring and assessment of sustainable development criteria for mineral operations. Emerging technologies were also presented that can assist in the development of criteria and performance indicators.

Jan 1, 2003

By R. M. Creamer

Attempts have been made to electroplate titanium and zirconium from aqueous, nonaqueous, and fused-salt electrolytes. Metals were produced only in fused-salt electrolytes, the major product being sponge metal. All other electrolytes gave only partial reduction of the metal ions. Fused alkali borate electrolytes containing titanium salts gave titanium boride powders and coatings of poor adherence. Some of the problems encountered in the deposition of these metals and some of the aspects of titanium and zirconium chemistry involved are discussed. INTRODUCTION Titanium and zirconium are both relatively light, noncorrosive metals with both military and civilian uses. This has led to intensive investigations into the metallurgy of these metals. Both metals are high in the Electrochemical Displacement Series and are difficult to prepare in a pure state. At present they are prepared by reducing their chlorides, using magnesium. Electrolytic reductions have resulted in the preparation of fine powders or sponge of variable quality. It is believed that a good process of electroplating these metals on a baser metal would result in a very desirable product. The objective of the research summarized in this report was to investigate methods of electrodepositing these metals, with the idea of producing uniform, coherent plates. Most of the work was concentrated on titanium, the more abundant of the two metals. A system developed for titanium should be applicable to zirconium owing to their chemical similarity. Information gained from these experiments may also be applicable to the electro-winning of the metal.

Jan 1, 1954

By Woodcock J. T

A sulphide ion selective electrode (ISE) is suitable for control of sodium sulphide additions in flotation because it has a rapid response to changeS in S2- concentrations, can indicate -low concentrations at differentpH values, suffers from few interferences, and is robust enou'gh to use in a pulp. Three sulphidization techniques were studied using the lSE electrode for measurement and/or control of S2- levels. Metallurgy was assessedfrom concentrate grades and copper recovery.With slug additions of sodium sulphide, sulphidizing conditions were poorly defined and reproducibility tended to be poor. Although acceptable metallurgy could be achieved by multiple additions, sodium sulphide consumption was high.Controlled potential sulphidization readily gave good metallurgy. The optimum potential of the lSE for sulphidizing was about -500 mV versus SCE, but depended on sulphidization and flotation times; suitable times were3 and 5 min respectively for three to five stages. Application of this technique to previously untested ores gave good metallurgy in a first test in spite of variation by a factor of three in the sodium sulphide requirements ofthe ores.Simultaneous sulphidization and flotation was satisfactory when conducted at an lSE potential of -450 mV versus SCE. Mixed cha!copyrite-oxide copper ores responded satisfactorily.Besides optimizing sulphidization conditions it is also necessary to optimize xanthate additions (e.g. by measuring xanthate residuals).

Jan 1, 1978

By Elizma Ford, Vincent Sithole

"Two shortened test procedures for estimating the Bond ball work index are compared for suitability of use on Zambian/DRC-type copper–cobalt ores. The first procedure is based on a batch milling test while the second procedure is based on a limited locked-cycle test. Both procedures were conducted using a standard Bond test mill. INTRODUCTION The Bond ball work index is widely used in the field of minerals processing as an indicator of ore grindability. The work index is determined by means of a locked-cycle test procedure that typically requires seven to eight cycles to stabilise at a re-circulating load of 250%. A typical test requires between three to four kilogram of ore sample and around eight hours of operator time. For geometallurgical test work applications, where a large number of variability samples are to be tested, it would be highly beneficial to use a test procedure that requires less sample mass and operator time. Certain test work laboratories, for example SGS and JK Tech, are already offering various types of shortened test procedures for estimating the Bond ball work index. This paper discusses a comparison of two shortened test procedures that were evaluated for suitability of use on Zambian/DRC-type copper–cobalt ores. EXPERIMENTAL Test Procedure 1 – Batch Milling The first test procedure is derived from a batch milling approach proposed by the University of Hacettepe (Aksani, 2000). Some modifications were, however, made to the data analysis method from that originally proposed. During this test procedure, a 700 mL volume of sample is milled in a standard Bond test mill for a pre-determined number of revolutions. The feed and product particle size distributions are measured for each test. These results are then used to back-calculate a cumulative breakage rate parameter (k) for each particle size, according to the following formula:"

Jan 1, 2015

By W. R. Dengler, R. S. Brown

In 1974, Brunswick Mining and Smelting Corporation Limited started a 48 million dollar expansion programme at their property in Bathurst, New Brunswick. A portion of the expansion plans includes a 26 foot diameter 4,525 foot deep shaft, underground crusher and conveyor excavations and lower level access development. J. S. Redpath Limited was awarded the contract for the new shaft and associated rock work in May 1974. Brunswick Mining and Smelting Corporation Limited, a member of the Noranda Group, operate this 10,000 ton per day lead, zinc, copper plant with proven reserves in excess of 90 million tons. While most of the ore is provided by the underground operation at the Number 12 ore body, some tonnage is produced from the open pit at the Number 6 ore body. Long range plans indicate a phasing out of the open pit and an increase in production from the underground operation. Existing facilities at the underground mine could not provide additional tonnage, thus the requirement for a new shaft. (Figure 1) The new shaft will also provide access to ore below the 2,800 level which is currently the bottom level of the existing facility. The contract called for sinking a 26 foot inside diameter, nine compartment concrete shaft 4,525 feet deep (Figure 2). Station access and ramp development from existing workings would be required to the bottom of the new shaft. In addition, development work for new crushing and conveying facilities was needed simultaneous with the shaft sinking.

Jan 1, 1976

By Jose L. Garcia

The following document aims to cover all issues concerning the three main methods employed for the in-situ survey of concrete pile integrity. Within it are described both sonic coring and low-strain tests and the frequency and time domain analysis of their results, which are the most advanced techniques currently in use in Spain. The survey techniques described were developed and began worldwide deployment in the 1960s, but it was not until the 1980s that they saw large scale implementation in Spain, largely thanks to the miniaturisation of electronics and computer equipment that made them easier to use on-site. Sonic coring, echo and frequency-response testing or mechanical impedance tests are spreading further every day. However, there appears to be a need for standardisation of the testing methods, as well as their implementation, interpretation and the presentation of results. The goal of these Spanish recommendations is to serve as a guideline for test standards and to provide examples for a correct and commonly agreed interpretation of test results, as well as settling any differences in the evaluation of defects detected in foundation works.

Jan 1, 2006

By B. W. Gandrud

At the Southern Experiment Station of the Federal Bureau of Mines, reports are prepared from time to time on results of washability studies of commercially important coal beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. This report records the results obtained on a sample of run-of-mine coal taken in June 1953 from the Pratt bed at the Davidson Coal Co. mine about 1 mile west of Graysville, Ala. One of the main objectives of a washability study is to obtain technically and commercially important data in connection with the best methods for preparing and utilizing the Nation's limited reserves of good coking coal. Such information is important from the standpoint of conservation in that it facilitates selection of preparation methods that will yield an acceptable grade of coking coal with a mini-mum of losses of coal in the rejects. The Pratt bed is one of the main sources of coking coal in the Jefferson County part of the Warrior field. This is the first time, however, that data from a complete washability study of coal have been obtained from this bed in Jefferson County. In the Graysville area, Pratt-bed coal has good coking characteristics and is used for blending with other coals in making metallurgical coal. The extent of its use in such blends is severely limited in this area, however, by the fact that it has a high sulfur content, which has not been reducible to any great extent by washery treatment.

Jan 1, 1955

By Hani Mitri

Understanding the interaction between rock bolts and underground rock movement is critical for safe and cost effective underground excavation design. Although early research on this subject involved a balance of theoretical analysis and field measurement, recent work has been heavily focused on analytical and numerical studies. This paper describes technologies that have the potential to redress the balance through instrumentation of rock bolts deployed under routine operating conditions in underground mines. Two new products are presented in this paper. Firstly the U-cell coupler is a load cell device that can be routinely coupled to the threaded end of a bolt prior to installation. It measures the ?series? load at the head of the bolt. Secondly, the d-REBAR involves an array of small-diameter, long-base length displacement sensors recessed into grooves along the entire length of the bolt. Both new instruments are interfaced with on-board digital signal conditioning and telemetry. Methodologies for the deployment of the new instrumentation and guidelines are presented for the interpretation of results based on data obtained from field trials. Successful field installations demonstrate the viability and practicality of these new technologies and, moreover, provide important insight in to rock bolt/rock mass interaction.

Jan 1, 2012

By C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA) system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By G. F. Kuncir

The time-cost-risk analysis described herein was performed as part of an evaluation of the Advancing Oil Shale Mining Technology Program performed by The Aerospace Corporation. The objectives of this analysis are to assess the feasibility of the program relative' to time and cost constraints, and to determine the probabilities of achieving various technological goals. A combination of standard program planning and analysis techniques were used to achieve these objectives. These included a critical path analysis, a resource allocation analysis, and a risk analysis.

Jan 1, 1977

By P. Ashayer, J. Curran

Introduction Rockfalls occur when rocks or boulders detach from mountains or hills and tumble down. They can pose significant hazards to infrastructure such as highways, buildings, and mine open pits, and they sometimes result in personal injury or death. Prediction of rockfalls is a difficult task. Slopes that are at risk of rockfall have highly variable geometries. The location, mass, and shape of the rocks that might dislodge and fall are uncertain. Moreover, the materials that make up a slope can vary considerably from one section to another. Furthermore, the relevant material properties are usually not well known. Performing probabilistic simulations of rockfalls, combined with proper statistical analyses, has proven to be an effective and acceptable method for dealing with these difficulties [1, 2, 3]. The movements of a falling rock can be classified as freefall, bouncing, sliding, toppling, or rolling. The falling trajectory is controlled mainly by the geometry of the slope, the block shape, and the energy dissipated at each contact of the block with the slope. A rockfall model is evaluated based on its ability to efficiently predict the velocity, frequency, height of bounce, and run-out distance of falling rocks. With this information, the engineer can design remedial measures such as restraining nets and ditches. Most of the existing rockfall simulators are based on particle models that consider the falling rock as an infinitesimal particle with a mass, called the lumped mass or stereomechanical models [1, 2, 3, 4]. Other models involve hybrid methods relying on simplified assumptions. The most common hybrid methods are based on contact searching for the movement of a dimensionless object and incorporate some aspects of rigid body impact for bouncing [5, 6, 7]. There are also some rigid body models in the literature that employ simplified versions of rigid body models [8, 9]. This study applies a more sophisticated rigid body theory based on rigid body impact mechanics (RBIM), which was developed by Stronge [10, 11, 12]. The new theory captures all modes of rigid body movement. Due to the importance of the rock geometry, single impacts of ellipsoidal and prismatic rocks with rectangular cross sections are investigated. The effect of rock slenderness on rebound velocities and energies is also investigated for ellipsoidal rocks. The correspondence between the model parameters and the data from the rockfall literature data will be discussed.

Jan 1, 2007

By S. M. Shelton

Tests employing various ore-dressing methods were made on a manganese wad ore from the W. A. Chinn property in the Batesville-Cushman district of Arkansas in an effort to develop a practicable procedure for the production of ferromanganese-grade concentrates. The ore body occurs as a bed approximately 7 feet thick in the residual clay of the Ferndale limestone formation5/. The crude wad ores are soft aggregates of various oxides of manganese, which are loosely bonded together. Hard lumps of high-grade ore are disseminated throughout the wad. Hausmannite, pyrolusite, and psilomelane are the principal minerals. Some clay is present, but most of the gangue consists of leached fragments of the original siliceous and calcareous rocks in which the manganese occurred. In addition, hydrated oxides of iron, which axe present, also must be considered as gangue. Definite phosphate minerals have not been identified.

Jan 1, 1942

By A. D. Hammond

Vanadium is a transition metal, ductile and silver-gray. It is harder than most metals and steels and it has a good resistance to corrosion. It is stable against alkalis and sulfuric and hydrochloric acids. Vanadium is oxidized in air at about 660° C (1,220° F), although an oxide layer forms even at room temperature. The chemistry of vanadium is noteworthy for the accessibility of the four adjacent oxidation states, 2-5. In aqueous solution, the colors are lilac V2+, green V3+, blue VO2+ and, at high pH, yellow VO42-. Considered to be as abundant as zinc, metallic vanadium is not found in nature, but it is known to exist in about 65 different minerals. Economically significant examples include patronite (VS4), vanadinite (Pb5(VO4)3Cl), associated to the uranium mineral carnotite (K2(UO2)2(VO4)2?3H2O) and in a vanadium mica called roscoelite K(V3+,Al,Mg)[(Si,Al)4O10] (OH)2. Other important vanadium ore oxides are montroseite (V,Fe)O(OH) and corvusite (Na,Ca,K)V8O2.4H2O. Much of the world?s vanadium mine production comes from magnetite-hosted deposits and, to a lesser extent, sedimentary-hosted sandstone.

Dec 1, 2013

By C. M. K. Boldt

The Bureau of Mines studied the compaction characteristics of metal and nonmetal tailings. Densities of the tailings and zone of compaction influence, compactive effort, and cost of equipment are related to changes in the factor of safety for specific grain-sized tailings and embankment configurations. Field testing was accomplished in two distinct phases. The first phase investigated the effectiveness of using a nuclear gauge on metal and nonmetal tailings to produce rapid, instantaneous measurements of moisture content, wet density, and dry density. The results of the nuclear gauge testing are presented in chapter 1. Chapter 2 presents a comparison of the compactive effectiveness of three different pieces of construction equipment on a coarse-grained metal tailings pond. The three pieces of equipment chosen for study were a DBH track-mounted dozer, a DSOO rubber-tired dozer, and a SP848 vibratory smooth-drum compactor.

Jan 1, 1985