Search Documents

Two concentrates from Palabora, in South Africa, containing 0.056-0.068% undesirable Cu and 0.8 or 2.2% Ti, were chlorinated with air:chlorine ratios of 10:1, 15:1 and 20:1 at temperatures between 1 200 and 1 329 K. The resulting volatile chlorides were condensed and the solutions analysed for Cu, Fe and Ti. Recovery of Cu was less than 25% at low temperatures and short reaction times, but at 1 258 K almost all Cu was removed from the magnetite at all ratios of chlorine to air. At higher temperatures, the increased carrying over of iron as FeCl3 could be minimised by decreasing the partial pressure of chlorine. No titanium was detected in the volatile products and the percentage of Cu recovered was independent of Ti concentration in the concentrates, though as a function of Cl2 vol%, more Cu was recovered at 1 200 K from the low-Ti than from the high-Ti concentrate. In a fluidised-bed reactor, Cu recovery was 58-90% and iron carry-over less than 10 ppm

Jun 21, 1905

By Jim Sadowski, Steve Stewart, Bob McMurdy, Martin Nevens

"Mohawk Garnet has been operating a small pilot plant near Sudbury, Ontario for several years attempting to produce commercially viable garnet. The challenges of operating a pilot scale mining, processing, and product handling operation as a full time plant have led Mohawk Garnet to seek a better way. In co-operation with Mohawk Garnet, Outotec (USA) Inc. has taken on the technical and design challenges of increasing garnet product from twenty tonnes per day to two hundred tonnes per day.Outotec performed a comprehensive test and flowsheet development program applying Outotec’s density separators, spirals, flotation, and other technologies to design a successful process for the separation and recovery of the valuable garnet for Mohawk.This paper explores the test program, the process flowsheet development work, plant design and preliminary engineering of a new garnet processing. The various technical challenges, process technologies involved, and design concepts will be discussed.INTRODUCTIONMohawk garnet has been operating a small-scale garnet mine and process plant in Wahnapitae, Ontario near Sudbury.The current operation was intended to be a pilot plant and so only produces 20-25 tonnes of garnet concentrate per day. The garnet is bagged and sold for use as abrasive. The process is inefficient with low yields, poor material handling and very high cost per tonne. Mohawk garnet approached Outotec to help them improve their garnet process and transform themselves into a larger scale and more efficient operation."

Jan 1, 2010

By Terry McMahon

This Bureau of Mines report describes the rock burst problem and measures being taken for its alleviation in the deep underground mines of the Coeur d?Alene Mining District in northern Idaho. The geologic features that contribute to rock bursting in that area are discussed and briefly compared with similar features in other burst-prone mining districts throughout the world. Early investigations to understand and control rock bursting are reviewed, and the mechanics of bursting are discussed in terms of the seismic events that produce them. Sources of strain energy, rock failure mechanisms, and the conditions necessary for the release of seismic energy are covered in detail. Rock burst research in the Coeur d'Alene District is described. Included are discussions of the microseismic method as both a research tool and as a rock burst monitoring system, rock destress blasting and preconditioning methods for rock burst control, and stoping methods currently being developed to reduce rock burst hazards.

Jan 1, 1988

By A. Vorster

The objective with mine planning is to consistently deliver production conforming to quality and quantity requirements throughout the life of the mine. The complexity of the operational context of the modern mine extends far beyond the actual production actions and there is a need to find ways of analysing and managing this extended environment. A well-established approach to handling complex situations rely on the creation of representative models that use classification and visualization strategies. An example of the use of a classification scheme is the periodic table of the elements. All physical matter can be expressed as combinations of basic elements. Not only is the periodic table useful in classifying and identifying matter but it can also be used for the prediction of the properties of unknown matter and compositions of elements.

Jan 1, 2001

By Patrick Polk

For many years, sulfuric acid producers all over the world have been forced to meet ever more strict environmental regulations to reduce SO2 emissions. The sulfuric acid industry has implemented new solutions in order to comply with the new lower SO2 emissions target. Haldor Topsoe (Topsoe) has responded to this challenge by continuously improving the range of VK sulfuric acid catalysts and providing tailor-made catalyst solutions to meet the demands of the sulfuric acid producers for lower SO2 emissions. Reducing emissions through catalysis: requires less capital than installing a scrubber, requires no additional process chemicals, generates no waste or by-product to dispose of. In 1996 Topsoe introduced VK69, a cesium-promoted vanadium catalyst, designed for operation in the pass(es) after the intermediate absorption tower in double absorption plants. The high activity of VK69 allows for a more than 50% reduction in SO2 emissions from existing double-absorption plants. Topsoe currently has more than 110 installations of VK69. To comply with the still more stringent regulations being placed on the sulfuric acid industry to lower SO2 emissions, Topsoe has developed a new sulfuric acid catalyst designated VK-701 LEAP5™. This catalyst was introduced to the market in 2010. VK-701 LEAP5™ is based on a novel technology which circumvents the internal transport deficiencies of existing commercial sulfuric acid catalysts and thereby offers exceptionally high activity in strong, SO3 rich gases. Sulfuric acid plants have used this catalyst to meet emissions requirements lower than previously believed possible with a catalyst only solution. This paper will present examples on how to reduce emissions by implementing a tailor-made catalyst solution using VK69 and VK-701 LEAP5™.

Jan 1, 2014

By L. K. Smith

The position of Australia as a continuing long-term supplier of mineral sands, and their upgraded products, has been reinforced with the discovery of the extensive mineral reserves in the Murray Basin, an area covering parts of South Australia, New South Wales and Victoria. A major impurity in the Murray Basin is chromium, mainly present in ilmenite concentrates as individual chrome spinel grains. Magnetizing roast treatments are being evaluated as a means of removing the chrome spinel impurity from the ilmenite and as a result of the roast and magnetic separation treatments, the chrome spinels can be expected to be concentrated in the non-magnetic reject fractions. It is from these fractions that attempts were made in this study to recover a chromium-rich product by magnetic fractionation and by application of flotation. The high gauss non-magnetic rejects from the roasting of a primary and a secondary ilmenite fraction were magnetically fractionated to obtain a product with 40.5 and 28.7 per cent Cr2O3,respectively. From the high gauss non-magnetic reject from the roasting of a primary ilmenite, flotation produced a chromium-rich product assaying 29.5 wt per cent Cr2O3at 69.0 per cent recovery. In another test a magnetic fraction assaying 32.9 wt per cent Cr2O3was floated to yield a chromium-rich product with 39.7 wt per cent Cr2O3at 96.4 per cent recovery. X-ray diffraction patterns of all the products indicated that the spinel concentrated was a ferroan magnesiochromite with rutile, ilmenite and hematite as impurities. Since all products were from a single pass, further processing can be expected to remove the impurity minerals and yield higher grade products. The material produced from the Murray Basin ilmenites in this study had similar compositions to commercial chromite ores, except for titania levels that were much higher. The high titania levels were due to residual rutile in the products, but it is expected that this can be removed with further processing. The mineral sand deposits in the Murray Basin are scattered over a wide area and the amount of chromite that may be produced from each of these deposits is unlikely to be sufficient to support an export market. Consequently, any chromite produced in the Murray Basin will most likely need to be processed locally to value added products for a niche market such as chemicals production. Keywords: Murray Basin, ilmenite, chrome spinel, roasting, magnetic separation, chromite ore

Jan 1, 2003

By F. R. Erick Mulder

"AbstractTwo bottom-hole samples have been taken from two new completions in the Turner Valley field, Royalite Lowery No. 8 on the west flank and Royalite No. 73, which was deepened into a lower fault block, on the northeast flank. From the bottom-hole oil of Royalite Lowary No. 8 a synthetic sample was prepared to simulate the original fluid in the reservoir, saturated at the gas-oil contact conditions. The sample from Royalite Lewery No. 8 has been shown to be the original fluid present at this well and represents the oil phase near the oil-water contact in• the reservoir. Complete chemical analysis, P.V.T., and viscosity data have been obtained on these reservoir fluids, which represent the range of saturation from the gas-oil to the oil-water contact in the Turner Valley oil structures. Sampling techniques and the application of the analytical data to reservoir conditions and field operations are discussed. Super-compressibility curves for an average separator tail gas have also been prepared. These data have not been available before. They will be of fundamental value in futu.re reservoir engineering studies of this field and will also serve as a guide in determining operating practices."

Jan 1, 1950

By A. E. Gooch

The Bureau of Mines conducted research in an attempt to provide a more sound basis for recommending improved artificial support during deepening of the main shaft of the Lucky Friday mine in the Coeur d'Alene mining district of northern Idaho. Field measurements of closure across the short axis of the 13-by 26-foot shaft were as high as 16 inches. Elastic/plastic finite-element (F/E) analyses were made, reducing the values of large-scale in situ rock mass properties until field closure measurements generally corresponded to displacements in the F/E analyses. Resulting plots of rock mass displacements, stresses, and areas of plastic failure display the results of creating openings (shaft, in this case) in deep mines in difficult ground conditions requiring artificial support.

Jan 1, 1976

Development of aggregate resources for use in structural concrete has been encouraged in Japan to support infrastructure improvement and national land conservation. Natural aggregate is a valuable resource necessary for sound economic development, and its importance is growing. After completion of aggregate mining projects, planting and afforestation are implemented. But sandy soil in excavation sites is not optimum for the growth of vegetation, and many years are needed before forests are restored. Planting techniques should be improved to support efficient reforestation in a shorter period of time. For this purpose, problems hampering growth of vegetation must to be solved through application of physical and physicochemical techniques to ensure that the environment and the ecosystem will be conserved in project sites.

Dec 6, 2010

By V. Bondarenko

The forecasting of floating earth inrush into the working is to a great extent connected with the investigation of the rock mass stressed-deformed state around the working. The aim of such investigations is to estimate the carrier ability of the protective layer (which is stabilized by the physico-chemical mode of fixing) and to determine it's thickness, which is to be sufficient to present the floating earth inrush into the working. We consider the protective layer to have exhausted it's carrier ability if the rocks of this layer reached the overlimit phase of deformation and it's greater part (section), which adjoins the working. is destroyed up to the limit of the remaining strength. So, the aim of investigations is to determine the size of the rocks inelastic deformation zone in the roof of the working. It is necessary to take into account the presence of water saturated seam in the roof and the overlimit characteristics of the rocks, their ability to lower the carrier capacity up to the level of the remaining strength.

Jan 1, 1996

Notwithstanding full concurrence with the dictum of a famous scientist that "definitions are the most accursed of all things on the face of the earth," in view of the considerable confusion which exists in jigging nomenclature, it is considered advisable to commence this paper with the following explanations of the terms which will be used throughout the text.Jig Bed. The whole layer of material lying on top of the jig screen.Ragging. The layer of denser material lying immediately above the jig screen, which is too coarse to pass through this screen and is confined horizontally by the cells of the top grid.Ore Column. The layer of ore pulp between the ragging and the top-water.Top Water. The water, carrying fine material in suspension, which flOiWS over the surface of the jig bed.Hutch Water. The water added to the jig below the screen. (Except for the water discharged with the hutch concentrate, the "hutch-water" eventually becomes "top-water.")Feed Water. The water in the ore pulp fed to the jig.(This water becomes part of the "top-water.")Pulsion. The period of the jigging cycle during which the water is moving upwards relative to the particles in the jig bed.

Jan 1, 1937

By R L. Langak, R A. Heins

The use of differences in specific gravity between minerals to separate them has long been utilized in the extractive industries. The environmental and cost benefits of the commercialized forms of these processes are well understood and widely used. Gravity concentration is used inter alia in the primary beneficiation of gold, diamonds, coal, tin, ferrous metal ores and andalusite. The potential for economic loss due to poor performance of these gravity processes is significant, but diverse in manifestation and regular process monitoring can prevent or at least reduce these losses. The measurement of performance of gravity processes has always presented a challenge, due primarily to the masses of material involved and the physical nature of the processes, generally typified by long reporting time, and hazardous materials (such as Tetrabromoethane) for float and sink type tests. The development of density tracers has improved this situation, however recovery of these tracers from the process streams created the next set of challenges, requiring significant manpower to physically remove tracers from product dewatering screens. Additions to these tracers (magnetic or x-ray fluorescent) eased the recovery mechanism issues but made them much more expensive to produce, hence operators became concerned about losses during process testing. In addition, magnetic recovery of smaller size tracers by a magnet suspended above a loaded screen panel is still problematic. The development of new low cost magnetic tracers has improved statistical significance of tracer tests, as the tracers themselves can be bought and used in much larger quantities, whilst still remaining economically viable. Coupled with the development of effective magnetic recovery technology, such as the Gekko MagScreen, for even fine sized tracers, on-line, continuous tracer testing is now becoming a reality. Whilst the development of high technology radio frequency detection tracer systems continues, enabling the real time measurement of the process and interpretation of results, miniaturization and recovery of these tracers, which is critical given their costs at present, remains an issue. Keywords: Gravity, process measurement, tracers, magnetic recovery

Jan 1, 2006

By D. D. Bush

Based on the results of this study, the underhand cut and fill stoping method, with mass destressing, is an effective method for controlling rock bursts and falls of ground for deep mining in the Coeur d'Alene Mining District. The procedure can be utilized to pull highly stressed pillars by converting from conventional overhand stoping methods or used as a primary recovery system. During the demonstration, only one minor rock burst occurred, with no injuries. The system facilitates accurate placement of vertical boreholes for effective mass destressing. Each mining cut is filled with cemented sandfill overlying a timbered mat that forms the back for the succeeding cut. For this demonstration, a cemented fill was mixed on the surface and piped to the stone. Costs for pillar recovery by this method are comparable and are considered cost effective over conventionally timbered overhand mining as a pillar recovery method.

Jan 1, 1982

By James C. Barker

A uniquely mineralized area extends from northwestern Canada through Alaska into eastern Siberia. Some of the metals found there are relatively rare in the conterminous United Stales. Among these are cobalt, the platinum-group metals, and chromite. Geologic evidence suggests that cobalt and the platinum-group metals may be present in deposits that could constitute nationally important reserves. Chromite in potentially minable deposits is known, but it may be relatively less abundant. Limited reserves of these metals have been delineated, but most of the favorable terranes and reported occurrences throughout the vast expanse of Alaska remain unexplored. As part of the mineral studies mandated under the Alaska National Interest Lands Conservation Act, the Bureau of Mines' Alaska Field Operations Center and the Bureau's research centers at Albany, Oreg., and Reno, Nev., are cooperating in a long- range program to investigate occurrences and delineate reserves of cobalt, the platinum-group metals, and chromite in Alaska. Studies of other critical and strategic minerals will be phased in during succeeding years, as ongoing projects are completed. This first in a series of annual reports summarizes available information about deposits and past production of cobalt, the platinum-group metals, and chromite, and describes current and planned Bureau investigations of these minerals.

Jan 1, 1981

By Carl R. Peterson

Development of reliable, portable, low headroom, hard rock crushers would improve the efficiency of most currently operated conveyor systems and make it possible to bring conveyor haulage closer to the face, thus eliminating expensive rock rehandling procedures. A crusher that could be easily moved would permit the more widespread use of lower cost haulage systems, such as conveyors, to transport the ore out of the mine. Such crushers would be installed close to the working areas, resulting in an optium haul from the face to the dump location. A recent contract study by Rapidex, Inc., "Application Study of Portable Underground Hard Pock Crusher" (USBM Contract No. J0265006) provides a survey of industry needs in portable underground crushing, together with conclusions and concepts as to specifications and type of crusher required to serve the greatest number of operations. To fill this need a three phase program has been undertaken by the Bureau of Mines: Phase I - Design: Phase II - Construction and Testing, and Phase III - Production Underground Test. This report covers Phase I only, and includes the complete engineering design and specifications of the Rapidex Rotary Jaw Crusher conceived in the earlier "Applications Study". Also included are the design, construction, and testing of a quarter-scale functional model, utilizing three different types of rock and two different crusher feeder systems.

Jan 1, 1978

By Russell J. Gartrell

This report describes the engineering feasibility and economic advantages of using a steep angle conveyance (SAC) system in conjunction with medium and large draglines to transport spoil in a typical Western Coal Mine. The SAC system, including a receiving hopper, a steep angle conveyor and a sticker/spreader, is capable of processing overburden material at the rate of 7,000 tons/hr. The unique feature of this system is the steep angle conveyor which transports the overburden material from the pit bottom to the top of the spoil at angles to 45 degrees. Compared to other means of cross-pit conveyance considered during this study, the SAC system offers the advantage of easier operation, lower conveyance cost and greater mobility. The results of this study have shown that integration of the SAC system into both established and planned new mines would improve the overall mining operation, expand the operating capability of existing equipment and reduce mining end reclamation cost.

Jan 1, 1977

ALAN W. CZARNOWSKY RMCMI PRESIDENT 1988-1989 on behalf of the RMCMI Board of Directors and Officers of The Rocky Mountain Coal Mining Institute cordially invites you and your family to attend the 85th Regular Meeting and Convention to be held June 25, 26 and 27, 1989 at Tamarron Durango, Colorado

Jan 1, 1988

By A. M. Gaudin

THE purpose of ore dressing is to separate the rough ore into one or several valuable concentrates and a discarded tailing. The first step is to crush the ore so that the resulting particles may be individually valuable or worthless. The next step generally has to be a sizing operation, because the property by which concentration is effected depends on the size of the in-dividual mineral particles as well as on their physical properties. These two effects may cancel each other if a preliminary sizing is not resorted to. Sizing is accomplished by screening or classifying. Screening depends almost solely on the dimensions of the particles; classifying depends also on the specific gravity of the particles and the viscosity of the settling medium in which the classifying operation is conducted. Classification, therefore, is to a certain extent a con-centrating operation as well as a sizing operation. Before the days of concentration by flotation, the available screens were mechanically poor. As a result classification was employed for sizing in the range. of comparatively coarse sands (table feeds). In recent years, the advent of stage-grinding to flotation size has brought about the development of good screens, which are more economical than classifiers down to about 20, -mesh. With decreasing size at which separation is to be made, screens become increasingly uneconomical, while classifiers become increasingly economical. The line of demarcation between the respective fields of screening .and classification is, therefore, fairly sharp. With the development of processes of concentrating finely comminuted ore, the need for classifiers or other sizing devices operating so as to make efficiently a split at a very fine size has become increasingly apparent. Such classifiers might be termed de-slimers, from the fact that they separate a material having a slimy ap-pearance from one having the characteristics of a sand. Sizing-tests are carried on by means of testing sieves, the finest of which have apertures of about 1/500 of an inch. The 200-mesh sieve, which has an average open-ing of 0.0029 linear inches is generally considered the limit of practical test-sizing. As a result, little is known of minus 200-mesh material and the advantages of classifying concentrator feeds within the minus 200-mesh range has been overlooked. An extension of the -present sieve scale beyond the 200-mesh screen is given in Table 1.

Jan 2, 1927

By Jose Luis Sosa, Marco Surichaqui, Ramirez Marcelino

El proyecto permite obtener resultados de operación que no siempre son los esperados en cuanto a calidad y recuperación, aquí es donde destaca el programa; tiene una data que PRONOSTICA estos resultados, con el control de parámetros, corrigiendo estos resultados al valor óptimo esperado, haciendo que su empleo permita obtener en “tiempo real” excelentes resultados en cuanto a calidad y recuperación del licor lixiviado y se refleja en costos.

Sep 1, 2017

By A. Engelbrecht, B. North, B. Oboirien

"There is large electricity generation potential in discard coal, both in stockpiles and current arisings. Power stations with a combined capacity of up to 18 GW electrical (GWe) could be fuelled by discard coal. Modern circulating fluidized bed combustion (CFBC) boilers, with capital costs comparable to equivalent pulverized fuel (PF) boilers, are capable of utilizing discard coal at a high efficiency while reducing sulphur dioxide (SO2) emissions though the use of limestone sorbent for ‘in-situ’ capture.A detailed economic assessment of the feasibility of electricity generation from discard coal, comprising material and energy balances and the construction of a discounted cash flow (DCF) table, shows that it is also potentially attractive from an economic perspective. A base case analysis shows positive net present values (NPVs) and an internal rate of return (IRR) of 21.4%. Sensitivity analyses on critical parameters show that the economic viability is heavily dependent on parameters such as coal cost and the value of electricity. The project becomes unattractive above a coal price of approximately R300 per ton and at an electricity value below approximately 59c per kilowatt-hour (kWh).Site- and project-specific information such as the delivered cost of coal, location and efficacy of sorbents, and effective value of the electricity produced can be used as input to the economic analysis to evaluate siting options and sorbent source options for such a power station."

Jan 1, 2015