Search Documents

Since the end of World War n, many important developments have taken place in the investigation of the phenomenon of brittle fracture in mild steel. Fractures in certain classes of welded ships, in welded bridges, penstocks, etc., focussed a great deal of attention on the interrelationships of design factors, service conditions, and steel quality on the generation of catastrophic failures.Much publicity has been given these major failures, and there is perhaps a tendency to forget that mild steel, under certain conditions, as well known to behave in a brittle fashion in a wide range of everyday engineering applications.For instance, many who are connected with the haulage and lifting of heavy loads will be familiar with the bright "crystalline" fractures of crane hooks and chains which sometimes follow sudden jarring; those concerned with the heavy pressing and shaping of steel plate will not be unaware that at times sudden brittle splits or tears will develop for no obvious reason in, say, rolled pipes or in dishings.In fact it will be evident upon reflection that in many cases the conditions which mild steel has to withstand during processing into an engineering part or structure are more severe than those it wili be called upon to endure during service. In this sense brittle fractu;res in mild steel are much more frequent than are commonly supposed.Two modes of fracture are now generally recognised to occur in metals, namely, shear and cleavage. The latter manifests itself by the so-called "crystalline" fracture (here...

Jan 1, 1954

By A. Vien

Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the results of a research program to evaluate the technical and economical merits of such a device on a SAG mill. The evaluation includes validation through discrete element modelling and comparison to measured static volumetric load. Inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed.

Jan 1, 2001

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals-pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent W03 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent WO3, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

By C. D. K. Gauert

High-pressure waterjet technology is proposed as an alternative tool for selective underground mining of high-grade ore sections in stratiform orebodies showing a preferred ?bottom? or ?top? enrichment such as the Witwatersrand reefs and the Bushveld Complex platiniferous reefs. This technique, utilizing known mining technology together with more advanced machinery and additives as used in industrial and cleaning applications, may lead to an increased life-of-mine (LOM) for mining operations. A series of experiments was successfully carried out in a laboratory on Witwatersrand quartzite material, indicating acceptable cutting performance. Mining volumes by selectively cutting of reef portions are considered to be comparable to traditional drilling and blasting. Economic advantages of waterjet mining include energy savings due to the lower quantity of gangue rock to be hoisted to surface, as well as savings by a decrease in the usage of blasting materials. Capital expenditure of waterjet cutting, if applied on a broad scale, could be lower in the long term than that of conventional drilling and blasting methods. Mining by the application of high-pressure waterjet technology could become a competitive ?green technology? improving the economics and safety of labour-intensive mining operations. This paper suggests that waterjet cutting at an industrial scale can become a routine hard-rock mining technique in the future. Keywords waterjet cutting, high pressure, mechanized narrow reef mining, abrasive agents, costs, selective mining.

Jan 1, 2013

By P González, E Córdova, E Faundez

An integrated mine system must be capable of displaying and reporting valuable information that can be used to easily understand, manage and take action on the key parameters being reported.One of the key aspects of integration is the standardisation of the mine information up to a level capable of adapting the main characteristics of past projects at the mine and enforcing the same or higher standards for newer projects being developed.At the El Teniente mine, photogrammetry is used to map the advance of horizontal developments, and the constructed 3D representation of each face is then used by the geologists to obtain structural information about the areas being photographed.The mine realised that valuable mining information could also be extracted from the photogrammetry being applied, with three possible areas of development envisioned.The first area was creating a link between the developments being planned on a yearly and monthly basis and matching them with plan sections of the 3D developments of the system to account for any deviations.The second area was to use vertical sections of the 3D developments to estimate the overbreak of the excavations in different areas of the mine.The third area was the provision of a more detailed analysis of the sections so that they could provide information on the thickness of the shotcrete being applied.This paper presents the different alternatives being used and examines how the project is currently being developed and managed at the mine. It also looks at the challenges associated with implementing the reporting platform and the results being obtained.CITATION:Córdova, E, Benado, D, González, P and Faundez, E, 2016. Mine planning information from photogrammetry sources at the El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 653–658 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Robert Boyd

The Diamond Markets ? Supply has continuously increased over the past 25 years ? However, global supply is expected to drop by 1 to 2% by 2015 ? Demand Driven Market ?Demand is expected to grow 3% annually through to 2015 ? Supply Squeeze Anticipated (2010 to 2015) ? Consumption is exceeding rate of discovery, mine development and reserve replacement ? These fundamentals are driving increased capacity and production at existing mines in South Africa, Botswana and Russia and new areas such as Canada ? Canada is now the third largest diamond producing country in the world ? These fundamentals are also driving record levels of exploration expenditures throughout the world with particular focus on Africa and Canada

May 1, 2006

By A. Galaitsis

This report summarizes part of the work performed under the USBM Contract No. H0155113, "Noise Abatement of Continuous Mining Machines." It reviews, briefly, the aboveground tests performed on a Jeffrey 120M conveyor that were documented in Vol. I of the subject contract; and describes the performance of treatments implemented on underground equipment. The noise level at the operator's position in the aboveground-test facility was reduced from 101.5 to 91 dBA using treatments with satisfactory - aboveground - durability. Extensive underground evaluation has been performed only on the constrained layer damping, which has reduced the conveyor noise by 2 to 6 dBA depending on the operating conditions, and has been shown to be sufficiently durable. Other promising candidates for exploratory evaluation include resilient layers for the top/bottom decks, and smoother discontinuities between adjacent conveyor sections.

Jan 1, 1983

By S Bluhm, L van den Berg

In planning mine ventilation systems, heat issues are normally associated with deep-level mines where auto-compression and virgin rock temperatures play a major role. However, a number of mines suffer from high ambient temperatures and humidity, very steep virgin rock temperature gradients and an influx of hot groundwater. Mines in Australia and, particularly, South-East Asia have to deal with these environmental conditions, both in the operational and planning phases. These operations normally have to take heat into consideration during the planning stages at much shallower depths. In high rainfall regions, the water table is saturated and groundwater flow rates are particularly high, which add significant water heat load potential to the mine ventilation system.This paper considers the ventilation challenges associated with hot groundwater conditions in mechanised mines. The paper is based on specific project experience gained from a number of projects in the United States, Australia and South-East Asia and draws on data from mines that experience hot groundwater conditions. For one site, actual decline temperature survey measurements, modelling techniques, management strategies and design considerations are presented.CITATION:Van den Berg, L and Bluhm, S, 2015. Ventilation planning considerations when dealing with hot groundwater, in Proceedings The Australian Mine Ventilation Conference, pp 211–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Lincoln A. Stewart, P. S. Haury

"INTRODUCTION AND RESUME Arizona asbestos mines are the only sources on the American continents of iron-free chrysotile spinning fiber that meets the Navy specifications for asbestos fiber for use in covering electrical cables. Rhodesia normally supplies the bulk of this grade of asbestos at about half the Price of Ari zona spinning fiber. The acute submarine menace in 1942 focused attention on the danger that imports might be cut off and that a sudden demand for greatly expanded production might fall on the Arizona mines to supply the tonnage of this essential material needed for war production.A joint preliminary investigation of Arizona asbestos deposits was made in August 1941 by J. R. Thoenen, senior mining engineer of the Bureau of Mines and A. E. Granger, a geologist of the United States Geological Survey. A more extended investigation of the numerous asbestos mines and prospects, which are scattered over 25 townships of difficult terrain in Gila County, was begun by the senior author in August 1942.The Geological Survey assigned two geologists (Newton Chute and A. F. Shride) a few weeks later to study the geology as an aid in selecting the mines for the Bureau's exploration projects. Six mines were selected for exploratory work because it was desired to prove reserves of ore where production could be started quickly if urgent demand should arise. Acceleration of production is normally slow because of adverse operating conditions. First, the mines are at distances of 35 to 100 miles from Globe, the shipping and supply point, and the roads are few and poor. The mine openings start in steep canyon walls, so that mining supplies usually have to be packed in and the product packed out over 0.5 to 5 miles of burro trail. Second, most of the ore deposits are small, and the ratio of rock broken to spinning fiber recovered is very high, usually exceeding 200."

Aug 1, 1947

By J. J. Forbes

The activities of the Bureau of Mines include the development and testing of self-contained oxygen breathing apparatus and other devices for respiratory protection, the development and tasting of devices for detecting dangerous or noxious mine atmospheres, and the training of men in the mineral industries in the use and care of this equipment to enable them to render effective service in mine rescue and recovery operations following mine fires and explosions, or under other conditions where irrespirable gases may be found in mines or mining plants. The first use of self-contained oxygen breathing apparatus for com- bating mine fires and explosions in the United States dates back about 30 years. Previous to that time, exploration for any distance ahead of fresh air was virtually impossible without great risk to life; moreover, the men called upon to render service at mine disasters were not well-versed in the properties and physiological effects of gases likely to be encountered. It was also impossible to work ahead of fresh air to restore ventilation, and if many stoppings were blown out by an explosion, air had to be introduced into whole areas or sections at once without knowledge of the conditions ahead; moving an explosive mixture of methane and air over live fire had to

Jan 1, 1938

By B. E. Davis

Over 80 pct of domestic phosphate rock, which is the starting material for phosphorus-containing fertilizers, comes from central Florida deposits. As K-her grade deposits are depleted, lower grade phosphate ores containing 'Mg0 in the form of dolomite are encountered. Treating high MgO ores with present beneficiation technology will not yield a concentrate meeting specifications for acidulation. The Bureau of Mines conducted research on three high-MgO phosphate samples from south Florida. The sales contained, in percent, 5.4 to 10.2 P205, 1.9 to 7.6 MgO, and 35.3 to 60.1 acid insolubles. A technique of sizing, grinding, desliming, scrubbing, and redesliming was used to produce a feed suitable for continuous flotation studies, A conventional fatty acid-fuel oil rougher flotation followed by two to three cleaner stages resulted in concentrates containing, in percent, 30.7 to 31.3 P205, 0.6 to 1.3 MgO, and 2.5 to 4.8 acid insolubles. The P205 recovery from the flotation feed ranged from 55.1 to 89.7 pct.

Jan 1, 1984

By M. Nyoka

Historically bauxite-based refractories have been used in applications where andalusite-based refractories could work. Bauxite-based refractories were chosen over andalusite-based refractories mainly because of the availability of low-cost Chinese bauxite and also because many furnaces were designed by international companies that cannot easily access high-quality products. Currently, the availability of low-cost bauxite is under threat as a result of high export duties and tariffs as well as restrictions on the amount of material that China allows to be exported. South Africa is a major producer of andalusite, and this guarantees stability with respect to both availability and price. Refractories based on andalusite have an added economic advantage over bauxite-based refractories in that unlike bauxite, which requires high-temperature calcination before use, andalusite is used in its raw state. This paper constitutes a literature study of the merits, both technical and economic, of using refractories based on andalusite compared to bauxite-based refractories. Keywords bauxite, andalusite, refractory, furnaces, calcination.

Aug 1, 2013

By Phil Pennington, D. Jack Adams

Mining and processing of minerals, metals, and fossil fuels can release selenium and arsenic into wastewaters. Both selenium and arsenic are difficult to remove to levels that meet current drinking water and discharge criteria. These metalloids can be used as electron acceptors by microorganisms transforming them back to reduced states, thus removing or stabilizing them. Bioremediation cost effectiveness will be discussed in terms of site information required, microbial populations, co-contaminants, pH, redox, and nutrients. Full-scale, economical ex situ and in situ biotreatments are possible and can produce 1,000’s of times less sludge than conventional precipitation technologies.

Jan 1, 2005

By W. L. Cornell

The Missouri lead ores are the only domestic sources of cobalt presently being mined and processed for other materials. They represent the best short-term solution for meeting up to 13 pct of the Nation's strategic and critical cobalt needs from domestic sources. Presently, the cobalt is lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minium impact on present production does not exist. This paper presents results of research, built upon earlier Bureau of Mines laboratory research, to enumerate the problems encountered in cobalt recovery from the copper concentrate under actual mill conditions; to present alternative solutions to these problems; and finally, to describe the best available technology for cobalt recovery within the imposed constraints. Mineralogical analyses showed the cobalt present as a distinct mineral phase, predominately siegenite, amenable to a physical separation method such as froth flotation. Flotation was chosen for recovery because of easy adaptation by the mills. Unit processes of grinding, conditioning, and flotation were studied individually and in concert, and a series of continuous tests were run based on the parameters developed to obtain engineering data for subsequent economic analysis. Overall cobalt grades of 3.00 wt pct at a recovery of 64.0 pct were achieved.

Jan 1, 1987

By S. Kamalpour

It has been observed that the productivity of ferromanganese furnaces, and the stability of metal and slag compositions, vary considerably according to the type of coke used as reductant. However, the desired properties of coke for optimum furnace performance are not well understood. In this investigation, the behaviour of four cokes, which exhibited a wide range of performance in ferromanganese production, was investigated by means of laboratory simulations of reducing conditions in the furnace. The Stationary Charge in Controlled Environment (SCICE) technique was used to simulate the conditions in the furnace shaft. Batches of raw materials, mixed in the same proportions as used in practice, were heated at fixed rates to 900, 1100 and 1300°C then cooled. The mass loss was used as a measure of the degree of reduction. Conditions in the lower part of the furnace were simulated by means of melt-reduction experiments in which lumps of coke were drilled out to form crucibles in which enriched ferromanganese slags were reduced at 1500 and 1550°C then cooled. An examination of the raw materials and the cooled, reacted charges using a variety of analytical and characterization techniques enabled the sequence of reaction and changes in morphology of the raw materials to be followed. This enabled an understanding of the behaviour of the cokes during reduction to be developed, which was then used to explain the observed performance of the cokes in practice. By relating the observed behaviour of the cokes in the laboratory tests to measurable properties of the unreacted cokes and to their observed performance in practice, it was shown that to achieve high productivity and good furnace performance, cokes should be selected to have moderately high reactivity towards CO2 (Boudouard reactivity) relative to conventional iron blast furnace cokes.

Jan 1, 2004

By William E. Ford, Edward Salisbury Dana

1. Normal Class (25) Barite Type 2. Hemimorphic Class (26) Calamine Type 3. Sphenoidal Class (27) Epsomite Type Mathematical Relations of the Orthorhombic System Crystallographic Axes. - The orthmhombic system includes all the forms which are referred to three axes at right angles to each other, all of different lengths. 296 Any one of the three axes may be taken as the vertical axis, c. Of the two horizontal axes the longer is always taken as the b or macro-axis * and when orientated is parallel to the observer. The a or brachy-axis is the shorter of the two horizontal axes and is perpendicular to the observer. The length of the b axis is taken as unity and the lengths of the other axes are expressed in terms of it. The axial ratio for barite, for instance, is a : b : c = 0'815 : 10 : 131. Fig. 296 shows the crystallographic axes for barite.

Jan 1, 1922

By Hebert Arias, Christian Mendoza, Mervin Tapia

El Complejo Pasco —ubicado en la Cordillera Oriental de los Andes de la sierra central del Perú, en el distrito de San Francisco de Asís, provincia y departamento de Pasco— está constituido por las unidades subterráneas de Atacocha y Porvenir, la operación a tajo abierto Glory Hole y tres proyectos brownfield ubicados en la periferia de la concesión. Tanto Atacocha como Porvenir son depósitos tipo skarn, con mineralización distal de Zn y Pb(+/-Au) y proximal de Zn+/-Cu, asociados a cuerpos hipoabisales de composición cuarzoandesítica y andesítica. Estudios y exploraciones recientes muestran otros tipos de sistemas mineralizados, como brechas tectónicas con reactivación hidrotermal tardía, un sistema epitermal de sulfuración intermedia en vetas, cuerpos irregulares, entre otros, y un sistema tipo pórfido. La Falla Milpo-Atacocha, de rumbo N-S, juega un rol importante, ya que los intrusivos (Stock Milpo y Santa Bárbara) que generan la mineralización del tipo skarn están controlados por esta falla. Existe otro tipo de mineralización, asociado al sistema NW-SE (Falla 13): un sistema epitermal de sulfuración intermedia. Este trabajo pretende mostrar los últimos avances en las interpretaciones metalogenéticas, producto de un intenso programa de exploración (aproximadamente 80,000 m. DDH / 2018) y de un programa de recategorización de recursos (a través de 60,000 m. DDH), que permitirá hacer posible una operación sostenible de 12 años.

May 22, 2019

By E. K. Stanek

The field tests involved ten coal mines in which transients were initiated on the dc system from which the parameters of the dc mine electrical power system could be determined. The data processing involved the use of a Fourier Analyzer to filter noise and fit an exponential curve to the field waveforms. From this data analysis it was possible to find the dc system resistance, inductance and time constant. The survey of nationally recognized laboratories was conducted to establish that the recommended test criteria were practical. The development of test criteria for dc fuses used in mines was based on the measurement of parameters in the field, the survey of testing laboratories, literature searches, laboratory test, etc. A computer program was written to analytically predict the parameters measured in the field. This approach has limitations but reasonable agreement with field results was obtained. A brief laboratory testing program was carried out to verify the practicality of the recommended criteria and establish the accuracy of the conclusions concerning dc fuse performance.

Jan 1, 1984

By J. B. Morrow

Methods of Coal Preparation Fundamentally, the object of coal preparation is to increase, economically, the value of a fuel by making it more suitable to the uses of the consumer. This can be accomplished in three major ways: 1.Screening or sizing 2.-Mixrng or blending 3.-Cleaning By combinations of any or all of these methods we can prepare coal to meet standard specifications-a process of standardization which is the more desirable the more nearly it approaches the unvarying quality of packaged goods, where the package you buy today and tomorrow is the same as that you bought yesterday. It should be noted that it is readily possible to get good cleaning and still have poor preparation because of faulty screening and mixing, and, on the other hand, it is possible to get a passable grade of cleaning, combined with good screening and mixing facilities.

Jan 1, 1931

By Jaan Kiusalaas

This report is a self-contained User Manual for a computer program called SPASID -- Subsidence Prediction and System Identification. The program has two primary functions: (i) Precalculation of ground movements due to underground mining operations using the influence function method; (ii) Computation of influence function and site parameters from measured displacements. SPASID is written in FORTRAN and consists of four modules: (i) Preprocessor Module that prepares and maintains surface and mine data bases; (ii) Subsidence Computation Module that predicts movements of the surface; (iii) System Identification Module which is used to calculate the optimal influence function parameters, and (iv) Postprocessor Module for generating graphic displays of subsidence data. The last module is somewhat machine dependent but has internal documentation to indicate potential changes. All of the modules may be run in either batch or interactive mode. The manual does not assume previous knowledge of the influence function method or programming competence.

Jan 1, 1983