Search Documents

By Frank A. Peters

This evaluation of the sulfurous acid process for the production of metallurgical-grade alumina is the first of a series concerning various known methods of extracting alumina from low-grade aluminous materials and was undertaken to permit comparison with other processes. In the process with which this Bureau of Mines report is concerned, calcined clay is leached under pressure with 20 percent sulfurous acid and then filtered to remove a siliceous residue. The aluminum sulfite remaining in the filtrate is precipitated as a monobasic sulfite which, together with iron sulfite, is then decomposed under pressure to form a crude alumina hydrate and iron oxide. This intermediate product is purified in a modified Bayer process to yield alumina suitable for electrolytic reduction to aluminum. A study estimate (16)3 is used for these evaluations. The capital cost, not including land, is estimated at $95,701,600 on a Marshall and Stevens index basis of 240.0 for a plant producing 1,000 tons a day of alumina or 350,000 tons a year. The annual operating cost for this size plant is estimated at $22,831,100 or $65.23 per ton of alumina using clay at $1 per ton. Depreciation and local taxes are included in the estimate, but profit and Federal taxes are not considered.

Jan 1, 1962

By R. P. Harvey, J. E. Walstrom, A. A. Brown

In view of the large number of wells directionally drilled from offshore platforms and urban drillsites, greater interest is being focused on the directional survey and on the uncertainty inherent in calculating the position of the bottom of the hole, or other benchmarks in the wellbore. Of the two methods presented here for evaluating this uncertainty, the first is analytical and uses the principles of probability and statistics. The second method uses Monte Carlo simulation to generate a pattern of the scatter of possible bottom-hole locations. Both methods are based on a model for which the usual assumption is made that the curvilinear axis of the wellbore is adequately represented by a large number, M, of linear segments joined end to end from the top to the bottom of the hole and closely following the course of the hole. The errors due to this approximation are assumed to be negligible and are not studied here. One form of the model is to consider that for a given hole there exists a perfect set of data describing it, of the above form. Each linear segment has an angle of inclination with the vertical 7, in radians, an azimuthal angle from true north xi in radians, and a length Si, in feet. The subscript variable, i, extends from 1 to M. Each of the M linear segments representing the axis of the wellbore has three components in the X, Y, and Z directions. These components are calculated from the equations: The bottom-hole coordinates as determined from the reference set of data for the wellbore are given by the following for i = 1 to M: X=SX, Y = Sy, Z=SZ; . (2) A directional survey instrument, lowered into the wellbore to the M segments, or stations, measures the values of the 7; and the 3,. In general, because of errors from various sources, the resulting angular measurements will not be precisely equal to the 7" and xi. Random variables l, and Ai are therefore considered with associated probability density functions fi(li) and gi(Ai), respectively, which represent the distributions of potential survey measurements for this hole. Since it is assumed that the values Si are accurately measured they are treated deterministically. The random variables corresponding to the surveyed bottom-hole coordinates are given, for i = 1 to M, by:

Jan 1, 1970

By Timothy M. Barton

The U.S. Bureau of Mines is conducting research to assess the effectiveness of different chain pillar designs in maintaining gate entry stability. A particular concern is ground control for deep-cover 1ongwalls located at depths in excess of 1,000 ft. The study described in this report was performed in two experimental sections in one longwall headgate section which contained three different pillar designs. Two of the designs used conventional abutment pillars, while the third was a total-yielding pillar system. Both of the test areas were located under 1,800 ft of cover. The purpose of this study was to evaluate the effectiveness of these three pillar designs for gate road stability. As the longwall mined passed the test areas, Bureau engineers monitored entry convergence, roof sag, and changes in roof quality. The study indicated that the all-yield system performed nearly as well as the better of the two abutment pillar systems; but all of the three designs would have failed to provide acceptable stability for second panel mining without considerable artificial support.

Jan 1, 1989

By S. Yerel

In a mineral processing plant, the determination of a preventive maintenance schedule is one of the most important maintenance policies. In this study, to determine the preventive maintenance schedule for the Emet Colemanite Mineral Processing Plant in Turkey, a mean quality control chart was constructed using the historical concentrate B2O3 grade data. The effect of preventive maintenance scheduling on B2O3 grades was monitored using the mean quality control chart. It was determined that recovery increased after each preventive maintenance scheduling. Close examination of the mean quality control charts indicated that there were three periods that showed different grade characteristics. These were identified as the period ?prior to preventive maintenance,? the period ?after preventive maintenance? and the period ?requiring preventive maintenance.? These periods were compared as two independent samples by using the Kolmogorov-Smirnov test. Application of this test for interpretation of the mean quality control chart enabled the authors to analyze the system effectively, and it showed that the preventive maintenance for this plant should be scheduled at four-month intervals.

Jan 1, 2007

By L. C. IlsLey

The United States Bureau of Mines has been conducting investigations of electrical equipment curing a period of more than 25 years in an endeavor to encourage the development of safer electrical equipment for coal mines. In order to conduct these investigations in an orderly manner they are carried out under a published schedule of tests known as Schedule 20, which specifies detailed requirements for motors, controllers, etc., and fees covering the various inspections and tests made as part of a routine investigation.

Jan 1, 1937

By C. Sawmliana

Deep-hole blasting operations in opencast mines are always associated with some annoyance to the surrounding areas in terms of ground vibration, noise, flyrock, etc. These become more severe when underground mines run parallel to them. Blasting in opencast mines may pose danger to the underground mines in terms of roof/side failures, damage of water dams, isolation/ventilation stoppings and other underground installations. The paper discusses a case study in India on the impact of deep-hole blasting in Ramagundam Opencast Project ? III on the stability of various water dams of GDK-6B Incline coal mine operating in close proximity. The stability of underground water dams of GDK-6B Incline mine was endangered due to deep-hole blasting at OCP-III. There were 15 water dams in seam 3 and 16 dams in seam 4 of the underground mine. The physical strength tests using a Schmidt Hammer instrument were carried out in all the 15 water dams of No. 3 seam and 16 water dams of No. 4 seam. The test revealed that there is a decrease in compressive strength values of three dams of seam 3, namely 6A, 6B and 7. Theose three dams were also directly connected to the water source. Water seepage was also observed from the surfaces of the three dams. However, they were found to be stable in accordance with their design parameters and damage point of view while considering a threshold value of ground vibration as 25 mm/s. It was found that the value of tensile stress generated by a vibration of 25 mm/s was much lower (i.e. 0.171N/mm2) than the tensile strength of the two weakest concrete dams (1.85 N/mm2). Ten experimental blasts were conducted at different working benches of the opencast mine and the ground vibration data were recorded in roof and pillars near various underground water dams. The maximum value of vibration data recorded was 5.9 mm/s in roof near dam no. 1 in seam 3 with the dominant peak frequency of 22 Hz. No adverse effect on either of the dams was observed after that blast. During the period of study, no deterioration/adverse impact was found in any dam of the mine. Based on the results of the study and the analyses of the data, optimized blast design parameters and explosives weight per delay were suggested for the opencast mine to maintain the safety of the underground water dams. Keywords: Opencast blasting, damage, water dams, underground mine, ground vibration

Jan 1, 2009

Gravity-driven rock falls account for a large proportion of all fatalities and injuries in underground mines. Potentially unstable blocks of rock are found in the hanging wall of excavations, which may be delineated by natural joints or stress fractures. These blocks, referred to as keyblocks, will fail if their weight exceeds the support capacity or if they are located between support units. This paper describes a computer program which simulates blocks in the hanging wall of an excavation based on measured properties of fractures and joints. Keyblocks are identified and placed at random locations in a predefined excavation. The keyblocks are tested against the support to determine whether they fail the support, drop out between the support or are stable. By repeating the procedure several thousand times, statistics of the probability of failure of the keyblocks are obtained. This approach allows the relative hazard associated with different types of support or excavation orientations to be obtained. It is concluded that a probabilistic approach is suitable for the evaluation of supports effectiveness in situations where large numbers of discontinuities or stress fractures are exposed in excavations.

Jan 1, 1998

By Joseph D. Davis, GEORGE S. POPE

This bulletin is the fourth of a series a showing the results of the purchase of coal by the Government under specifications. The work of inspecting and analyzing coal delivered on Government contracts was transferred to the Bureau of Mines by an act of Congress effective July 1, 1910. It had been carried on for several years before that date by the technologic branch of the United States Geological Survey. The purchase of coal on the dealer's statement as to quality or on the reputation of the mine or district producing the coal is gradually being discontinued. At present most coal-purchasing contracts make definite provision regarding the desired heating value of a coal and the composition as shown by analysis. The heating value is usually expressed in British thermal units" and the composition specified is that shown by proximate" analysis. The price to be paid for delivered coal is made to depend on whether the analyses and heating-value tests of samples representing the delivery show the quality to be above or below the quality set forth in the contract. Large coal consumers are beginning to appreciate more and more the importance of the cost of power as a factor in the cost of producing a finished article. The endeavor to increase the efficiency and the economical operation of a power plant calls for an intimate knowledge of the quality of the coal being used. The purchase of coal under specifications insures the purchaser getting what he pays for and the coal being of the quality guaranteed. In addition, the analyses and tests of the delivered coal furnish data whereby the power-plant results can be comprehensively studied and a continuous check maintained on the conditions of operation.

Jan 1, 1912

By Mark Maday

As part of the I-94 North-South Corridor reconstruction program, the Wisconsin Department of Transportation (department) is reconstructing the Mitchell Interchange in Milwaukee, Wisconsin. Located on the south side of Milwaukee near Mitchell International Airport, The Mitchell Interchange interconnects I-94, I-43 and I-894. Reconstruction began in 2009 with the letting of the first advance contract for local crossroad bridge reconstruction. A second advance contract for construction of collector-distributer roads on each side of the I-94 mainline was completed in 2010. The main contract involving reconstruction of the core of the Mitchell Interchange was let in the summer of 2010, and is scheduled to be completed by the end of 2012. The core contract includes construction of three cut and cover tunnels along two system interchange ramps. Construction of the three tunnel structures is on the critical construction path. The contract includes an interim contract completion date that requires the tunnels to be open to traffic by the end of 2011. A top down method of construction using drilled shaft secant piles for the sidewalls of the cut and cover tunnel structures was selected as the preferred structure type to address subsurface and construction schedule challenges. The department identified in pre bid coordination that no cost reduction incentives would be reviewed or accepted for changes in tunnel wall type. A major component of the tunnel structures requires the installation of 1,500, 4-foot diameter secant piles. This paper presents mitigation strategies to manage construction risks associated with the installation of the secant piles including; prequalification of the secant pile subcontractors, requirement for use of full depth temporary casing, a site specific quality control plan, specifying drilling equipment, and developing a geotechnical baseline report for this critical component of the Mitchell Interchange reconstruction project.

Jan 1, 2011

The formation and distribution of gold placers in active collisional mountain belts are directly related to the tectonic, topographic, climatic and erosional constraints prevailing on either side of the orogen at the time of placer formation. In the absence of pre-existing placer deposits, these factors combine to concentrate placer development on the side of the orogen facing the prevailing winds, where most of the erosion and uplift occurs. Drainage network changes and glaciation can significantly alter placer distribution with respect to source areas within the orogen. After collision stops, placer formation will proceed on both sides of the orogen as exhumation of the mountain belt ensues. Incorporation of pre-existing placers formed on ancient mountain belts into younger placers in subsequent orogens, may be recognised by anomalous placer distribution compared to the above model. Most of the relatively young giant placers such as those inNew Zealand, Chile, Bolivia and Columbia, exhibit these general patterns. Their character and mode of formation have important implications for the formation and distribution of much older placers, such as those in South Africa's Witwatersrand Basin.

Jan 1, 1996

CURRENT MATTERS Page Page New York Meeting : v 27th Engineers xl Year Book, 1918 v Professional Classes War Relief. x1i Minutes of Meeting, Board of W. S. S x1i Directors vi American Engineering Standards xlii President's Report vi Hadfield Prize xlv Local Section News: Members in Military Service... xlviii Columbia xiii Personal li San Francisco xiv Positions Vacant liii New York xvi _ Engineers Available liv Southern California xxxi Forthcoming Meetings 1v United Engineering Society xxxii Library...% lvi Engineering Council xxxv Membership lix Other Societies: Institute Committees lxxviii Mining and Metallurgical Soc- Officers and Directors lxxxvi iety of America xxxix

Jan 3, 1918

SECTION I Page Page Report of Nominating Committee. v Employment li Proceedings of St. Louis meeting. , vi Local Section News.: liv Engineering Foundation, Report Affiliated Student Societies lvi of Secretary xxxviii Forthcoming Meetings lvii Engineering Council xlii. Library lviii Suggested College Course on the Membership lxiii Human Side of Engineering... xlii Biographical Notices: Engineering Societies Club of Alexander Bryden. By C. L. Hawaii xlv Bryden lxxxiii Members in Military Service .... xlv E. F. R o e b e r . B y J. W. Meeting of Board of Directors...' xlvii Richards lxxxv 1918 Dues xlviii Institute Committees lxxxvi Transactions for 1917 xlviii Officers and Directors xciv Personal xlix

Jan 12, 1917

By R Wilson, R Williams, B Freeburn

McLanahan RSS14x50 scrubber screens have individually processed over 50 Mt of Pilbara iron ore. The first stage of separation in these plants with abrasive, high specific gravity, large lumps is an extremely arduous duty with high wear rates. With the Scrubber Screen layout this occurs in the attached trommel section. The initial supply of the replaceable trommel panels were of steel-backed rubber with a service life of approx. six weeks. Site Personnel established a goal of 26 week wear life in conjunction with 100 per cent reliability and while field trials were undertaken using a variety of hardened and cast steels that demonstrated wear life to the nominated requirement some unpredicted failures still occurred. With a long evaluation time and challenges to create repeatable conditions with field testing, a purpose built test unit was designed and constructed to allow controlled evaluation of a number of materials and designs. During 2016 tests were conducted with eight different materials, of varying thickness to simulate impact conditions and a number of aperture profiles to evaluate both impact and abrasion effects. From these results two designs were selected for full scale implementation to confirm the nominated goals. This paper will present details of both testing procedures and results of all materials, as well as conclusions of successful field implementation.CITATION:Wilson, R, Freeburn, B and Williams, R, 2017. Trommel panel development for iron ore applications, in Proceedings Iron Ore 2017, pp 251–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By P. Altounyan

Techniques used to safely control the roof in UK coal mines for some 10 years have been applied to a South African coal mine. This new approach known in the UK as advanced rockbolting technology, is based on applying four fundamental principles: ?Understanding the roof failure mechanisms ?Using an effective roof support system ?Designing this support using measurement ?Monitoring the performance of the system. The paper summarizes the approach in detail and describes how it is being applied by Anglo Coal, giving results obtained to date. Investigations at a number of South African coal mines, including stress measurements at two Anglo Coal mines, have confirmed that the mode of roof failure (lateral shearing due to horizontal stress) is the same as in other coalfields worldwide, and aspects of current world best practice, including the use of advanced technology rockbolting, are therefore relevant in South Africa. The stress measurements indicated a high level of stress field anisotropy and further investigation of stress conditions in South African coal mines is recommended. The most effective bolting system to resist shear failure is one with high bond strength and stiffness. Short encapsulation pull testing of existing South African systems confirmed that they have low bond strength and stiffness. An improved rockbolt system with the required performance, and features allowing rapid installation and installation quality and performance audit, has been developed and is currently under full-scale trial. Design by measurement and routine monitoring procedures including the use of a rotary telltale device are also under trial. It is anticipated that South African coal mines will be able to obtain significant safety and productivity benefits from the application of this technology.

Jan 1, 2001

By Robert G. Harris

During the last five years there have been significant improvements in face support monitoring techniques particularly in respect of face pressure. The measurement of support loading pressures was originally conceived as a maintenance aid for the hydraulic systems but recent work has also included geological loading displays of the complete face as well as individual supports. This paper briefly examines the means of obtaining this information, together with some examples of actual face data. Also included is a summary of the benefits of such monitoring and an outline of future development work.

Jan 1, 1993

By M. C. Irani

The Bureau of Mines, in cooperation with the Mine Safety Appliances Co., has developed a continuous-recording methanometer utilizing a catalytic combustion detector. The methanometer, which is presently operating at 22 exhaust fans at 14 mines in the Eastern coalfields, is reliable and simple to install, operate, and maintain. The instrument and the details of its installation and calibration are described. Analytical data obtained by infrared spectrophotometer and gas chromatograph are presented to substantiate its re liability.

Jan 1, 1974

By E. Gallestey, D. Groenveld, F. Kolb, M. Rozou

"Recent copper price evolution pushes modern mining industry even harder to achieve highest production with maximum efficiency. Operations are bound by numerous contractual and environmental conditions that bring a high degree of complexity to both the operators controlling the process and the plant managers assessing the circuit’s potential and setting the production goals.Advanced process control (APC) for grinding is one important tool to operate this most energy intense area in an optimal way, finding the optimal trade-offs between highest throughput, energy efficiency and product quality based on variable ore properties, production targets and management priorities.ABB’s state of the art control and optimization software platform enables user to design a controller based on model predictive control (MPC). The paper and the presentation show the technology used and the results achieved through an APC controller installed in a pilot project in Aitik (Boliden SA), Sweden. Furthermore, possibilities to interconnect grinding with other areas as stockpile management and flotation with various interconnected APC controllers will be shown. Finally, an example of the return on investment and the payback times based on the increased throughput and better product quality will be presented.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations (see Figure 1).The main goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. At the same time, it is also crucial to execute this process at the lowest possible energy and grinding media consumption."

Jan 1, 2015

By S. Panigrahi

The SO2-ammoniacal ammonium sulfate leach liquor generated by leaching of manganese nodules, after removal of minor quantities of iron and manganese, contained copper, nickel, cobalt, zinc and (NH4)2SO4. After extraction of copper from the leach liquor with LIX 84I, stripping of ammonia from the Cu-barren raffinate was carried out followed by precipitation of metal ions from the ammonia-stripped solution as sulfides. Leaching of the sulfide precipitate was carried out with H2SO4 to obtain a leach liquor containing 0.58 kg/m3 Cu, 2.67 kg/m3 Zn, 2.00 kg/m3 Co, 24.68 kg/m3 Ni and 10.0 kg/m3 (NH4)2SO4. After extraction of copper and zinc from the sulfate leach liquor with LIX 84I and D2EHPA, respectively, the solution was left with Co and Ni. Extraction of cobalt from the Cu- and Zn-free solution was carried out with 0.1 M PC88A and stripping of the cobalt-loaded organic was carried out with the cobalt-spent electrolyte (pH 1.4). Extraction of nickel from the cobalt-free solution was carried out with 90% neutral 1M NaPC88A followed by stripping of the nickel-loaded organic with 120 kg/m3 H2SO4 solution. Extraction of metal ions increased with increasing equilibrium pH and extractant concentration. The maximum separation factors, with respect to the pH and extractant concentration variation studies, were 3796.7 and 15350.0, respectively. The extracted species for the metal ions were CoA2?3HA and NiA2?5HA.

Jan 1, 2009

By J. E. Allison

As part of a Bureau of Mines research program to conserve critical and strategic metals, an aqueous electrodeposition method for preparing stainless-steel-type coatings was studied. Chromium powder (averaging 3 J1.m diam) was suspended in a ferrous-nickelous sulfate electroplating bath and occluded in the electrodeposited Fe-Ni alloy matrix. Subsequent heat treatment of the resulting composite coating formed the ternary alloy. The occlusion process was affected by the quantity of Cr powder suspended in the electrolyte and by the microstructure and composition of the electrodeposited matrix. Coatings containing up to 21 wt pct Cr were deposited from an electrolyte containing 20 vol pct suspended Cr powder. Heat treatment at 1,100° C for 8 h homogenized the composite coating. Deposition of 44Fe36Ni20Cr alloy coatings (250 J1.m thick) on AISI 1020 carbon steel rods, followed by heat treatment, provided complete protection of the carbon steel during exposure to a boiling 65-pct-HN03 solution. Corrosion rates of 0.6±OA mm/yr for the coating in the boiling HN03 approximate that of 304 stainless steel. Practically shaped electroforms have been prepared by the coating method.

Jan 1, 1989

By G. W. Center

This manual is intended to assist federal, state, and local regulatory and planning agencies, the mining industry and consulting engineers in determining the regulatory, environmental, technical and economic constraints influencing the site selection, planning, construction/operation and reclamation phases of a waste disposal facility. The information presented illustrates that factors affecting an individual site may be simple or very complex. This manual discusses methods for making future land use decisions, determining regulatory requirements, evaluating physical, chemical and structural properties of the disposed waste and selecting appropriate waste disposal methods and control techniques. Procedures and guides in the manual will assist personnel in assessing the complexities of waste disposal on a site specific basis. The major types of waste disposal systems are discussed and evaluated in terms of their advantages and disadvantages and applicability to varying site conditions and waste characteristics. Appropriate references following each chapter provide more detailed data on material presented in the text.

Jan 1, 1982