Search Documents

By J. P. D. Strydom

The transmission of excessive vibration to the human body can cause physical stress that may result in crippling pain or permanent disability. Rock drills are known to transmit high levels of vibration that are difficult to attenuate through conventional approaches to vibration isolation. However, it can be shown that once the ISO frequency weighting has been applied, most of the vibratory effect of the rock drill?s motion is concentrated at the drill?s operating frequency. This observation opens the way for utilizing a concept known as vibration absorption, aimed at attenuating the rock drill?s vibration. In essence this entails using the inertia of a secondary vibratory system to counteract the motion of the handle. This article documents an investigation into the use of such an absorber for attenuating rock drill vibration and demonstrates the feasibility of such an approach. A mathematical model of such an absorbing handle was developed and used for design studies. Based on these investigations an experimental prototype model was manufactured and tested. A significant reduction in vibration levels could be achieved.

Jan 1, 2002

By S. W. Stogran

"Chemical and limited biological monitoring of mine and mill effluents are being used by regulatory agencies to monitor and control discharges to the environment. Amendments to the Federal Fisheries Act may make it mandatory for mines to conduct Environmental Effects Monitoring (EEM) which will change the emphasis from monitoring effluents to monitoring impacts on receiving waters. The EEM amendments may expand the scope of present environmental studies to include: effluent mixing zone delineation; inventory and classification of resource, habitat, and historical receiving environment; effluent quality determination; chronic and acute bioassay testing; tissue analysis; benthic invertebrate monitoring; fish population surveying; fish tainting evaluation; and the evaluation of impacts on fish habitat, invertebrate communities and fisheries resources. The requirements for EEM have not yet been worked out by the mining industry and the government committee. Experience at Lakefield Research in conducting biological monitoring studies for the mining industry has shown that biological monitoring may be useful for assessing environmental impacts only if programs are planned and executed to collect relevant data, thus minimizing costs and maximizing effectiveness.IntroductionThe chemical monitoring of effluents and water bodies receiving effluents is common practice in the Canadian mining industry and has been used routinely by regulatory agencies to control discharges to the environment. Biological monitoring has also been used on a limited basis, primarily to augment chemical data collected. A number of regulatory bodies, primarily in Canada and the United States, have been incorporating biological monitoring into environmental regulations.Various forms of biological monitoring techniques have been used in Canada and the United States to help assess the impact of mining operations and effluents on the environment. Biological monitoring includes a wide range of activities, from monitoring metal uptake in individual organisms to examining the population dynamics in ecosystems. The most commonly employed biological monitoring techniques are the chronic lethality toxicity tests. Also becoming widely used are in situ and chronic toxicity tests."

Jan 1, 1994

Characterizing coal mine roof rock is extremely important for hazard assessment, reinforcement, and entry design. The Coal Mine Roof Rating (CMRR) is an innovative rock mass classification that has found acceptance in the coal mining industry. A disadvantage of the original CMRR is that it cannot be determined in advance of mining, because it requires underground observations. An entirely new set of procedures have now been developed to determine the CMRR from exploratory drill core, as described in this paper. The new procedures employ Point Load Tests (PLT) to determine strength parameters that account for approximately 60% of the rating. Both diametral (parallel to bedding) and axial (perpendicular to bedding) PLT are conducted. The diametral tests allow estimates of bedding plane cohesion and rock anisotropy, both of which are critical to estimating susceptibility to horizontal stress. Traditional core logging procedures are used to determine discontinuity spacing and roughness. To ensure compatibility with the original CMRR, the new rating scales were verified by comparing drill core results with nearby underground exposures. To assist mine planners in using the new CMRR procedures, a large database of strength ratings of roof rocks was assembled through extensive point load testing and logging. Over 2000 point load tests (both axial and diametral) have been made on 30 common coal measure rock types from mines representing most U.S. coalfields. This database has been merged with the popular core rating system of J.C. Ferm into a field guide for geologists and engineers. By using the pictorial classification system of Ferm to identify the rock, typical CMRR can be compared with values calculated using the new CMRR procedures.

Jan 1, 1996

By Shu Yan

The high resolution resistivity method (HRRM) is developed specifically for detecting underground cavities and tunnels. HRRM has a special feature in that it can recognize and cancel static shift, which makes it different &om the high density resistivity method (HDRM). In searching for various means for detecting underground cavities, we found that the detecting depth of the transient electromagnetic field method (EM) depends mainly on the measurement duration, not the loop area. In addition, TEM can also be used to locate the high-resistivity bodies. In order to use them for local working site conditions, we combine HRRM with TEM to become a combined electromagnetic method. Since the late 1980's this method has been used to locate abandoned mines and air passages and burning centers of mine fires with great success. This paper cites case studies for which this technique was successfully used.

Jan 1, 2005

By A. M. Hearn, J. R. Henning, A. S. J. Van Rensburg

The lining, together with the electrodes, forms the heart of the operation of a submerged arc furnace. Subsequent to a lining failure on M12 furnace during the early 1980s, Metalloys was active in investigating the concept of thermally efficient ?freeze? linings for its furnaces. The theory revolved around that, not only would, thermally efficient linings result in significant cost savings, but they would also last longer as a result of being subjected to less harsh operational conditions. After having proved the concept on the .smaller. furnaces, Metalloys decided to implement the concept on its largest submerged arc furnace, M12 Subsequent to having recovered from an impending failure of a lining installed in 1981 in M12 in the mid 1980s, Metalloys managed, through rigid lining management, to extend the life of this lining to 1999. At the end of 1999 the decision to replace the lining in the furnace with a ?freeze? lining was made and planning and design proceeded in earnest. This paper discusses the options considered in making the final decision. The features of the design of the lining are also discussed. Consideration is given to the furnace shell cooling system as a result of its importance in maintaining the thermal equilibrium in the lining. Note is made of the fact that the purchase of a .freeze. lining is an expensive exercise but that the time savings in the installation of the lining and the efficiency improvements during operation far outweigh the additional capital cost. The experience on M12 has been that the payback period of the marginal capital expenditure is less than three years. As a result of the opportunity to reline a furnace the size of M12 not presenting itself very often, the learning points from the installation of the lining and the operational advantages and disadvantages are significant. Finally, the point is made that the project had its pros and cons but overall the success of the project has been evident and, as such, the ?freeze? lining is likely to become the norm at Metalloys.

Jan 1, 2004

By Rose W. J

Geophysical prospecting was first recognized in Australia as an important aid to mining enterprises in 1927, when, on the suggestion of Sir Herbert Gepp, the "Imperial Geophysical Experimental Survey" was organized. The function of this survey was to carry out investigations on the applicability and efficacy of the most important geophysical methods under Australian conditions. The survey was formed under the joint auspices of the British Empire Marketing Board and Australian Commonwealth Government, and the investigations were carried out in Australia under the leadership of Mr. A. Broughton Edge, B.Sc., A.R.S.M., F.G.S., M.Inst.M.M., during the years 1928 and 1929. A description of the work performed, the apparatus used, the principles of the methods, and the results and conclusions of the survey are included in a report published by the Cambridge University Press in 1931.In 1932 Sir Herbert Gepp became interested in some gold mines in Eastern Victoria, in the Cassilis and Bethanga districts, and realizing that the lodes in these areas would be favorabIe for a geophysical examination, he arranged for a series of tests to be carried out. This work was performed by Mr. E. L. Blazey, B.E.E., a former member of the staff of the Imperial Geophysical Experimental, Survey, under the general direction of, and in consultation with, Mr. W. J. Rose, B.M.E.The work was commenced in October, 1932, at Cassilis, Vie., continued at Talgarno, Vie., .and concluded at...

Jan 1, 1933

By J. Ling, L. Racine, P. Cousin, A. R. Laplante

"The problem of gold recovery by gravity from high density gangues is first discussed from a fundamental perspective. Three potential difficulties are presented: poor liberation and fine gold particle size, concentrate bed erosion by coarse dense particles, and slow percolation of gold particle through the high density gangue bed. Two case studies are presented to illustrate the impact of these three problems on circuit performance and the feasibility of gravity recovery. It is concluded that careful testing can determine the scope of the first problem and feed preparation can limit the extent of the second. The third problem is clearly the most serious and results in lower gravity recoverable gold recoveries than would be achieved with the same recovery effort on a low density gangue application.IntroductionSince the commercialisation of the Knelson Concentrator in 1980, gold gravity recovery has experienced a surge in interest, in Canada and the United States first, then Australia, Zimbabwe and Russia, and finally worldwide. Table I details number of units sold in various countries, which corresponds approximately to their importance as gold producers 1. Exceptions. such as the low rank of South Africa or the importance of Zimbabwe, despite the much higher gold throughput of the former, are generally the result of differences in the effectiveness of the local marketing strategies, as well as a reflection of the ""philosophy of recovery"" prevalent in the country.The impact of the Knelson has not been felt equally in all plants. Typically, a highly successful application falls into the following categories: (a) alluvial or hard rock recovery for which gravity is the sole recovery method, (b) hard-rock free gold milling with ores which have a very high gravity-recoverable gold (GRG) content, (c) low grade sulphide copper-gold ores which include flotation ahead of cyanidation and (d) free-milling gold ores ahead of Other applications can be successful, but are not as common. The ""explosion"" of centrifuge concentration, of which the Knelson is the most successful but by no means the sole model, has created a certain euphoria which can be summarized as ""gravity recovery will improve the profitability of gold milling, no matter what."" This presentation is about applications that are not so successful, or even downright unsuccessful. The rationale is not to down-play gold gravity recovery, but to set it in its rightful position: metallurgically, it is not appropriate all of the times; it can become inappropriate if poorly designed; and it can be metallurgically possible but economically unjustifiable. In this paper, this will be illustrated and explained rather than demonstrated, with the use of both industrial plant surveys and laboratory test work. Alternate gravity approaches will be suggested."

Jan 1, 1997

SECTION I PAGE PAGE President's Western Trip v Presentation of the' John Fritz Hoover Makes Plea to. Stop Food Medal to Henry M. Howe.... xv Waste v International Mining Convention. xxxv. American Committee of Engineers Personal xl in London vii Employment xlii Proceedings, Meeting of Board of Local Section News xliii Directors : vii Forthcoming Meetings of Societies xlvii St. Louis Meeting V... Library xlviii The Woman's Auxiliary. xi Membership liv Members of the Institute in Mili- Biographical Notice of H. T. Chen. lxxiv tary Service xiv Institute Committees lxxv Officers and Directors lxxxii

Jan 7, 1917

In a field test at Mount Isa Mines Ltd., a system developed by ICI Australia Ltd. for bulk loading "MOLANITE", an ammonium nitrate slurry blasting agent into ring drilled holes of wblcvel open stopes, was shown to be satisfactory. The fragmentation produced by the slurry was a significant improvement over ANFO and the stope production rate was increased by approximately 50%. Indications are that the charging rate and labour costs will not be greatly changed if a slurry system is used.

Jan 1, 1973

By E Oktay, I Yusufoglu, C Kahruman

Powder and spherical pellets of MoO2 were oxidised under controlled conditions in the temperature range 674-791 K at oxygen partial pressures of 8.1-30.4 kPa. Weight increase during the reaction was determined by thermogravimetric analysis. It was concluded that the reaction is 0.6th order with respect to oxygen concentation and that the activation energy is 148 kJ/mole. In experiments conducted with powder, fast transfer of reaction heat to the gas phase created isothermal conditions, but the temperature of pellets rose by a maximum of 54 K at 674 K and 105 K at 791 K. The rise in temperature caused structural changes such as sintering and crack formation, which had a considerable effect on the reaction rate. The findings should be taken into account in the design of equipment and choice of operating conditions for roasting MoS2

Jun 21, 1905

The great problem at Port Pirie and many other lead smelters has always been to keep the lead content of the slags down to a low level. This has been done in the past largely by empirical methods, the lead content varying from less than 1 per cent to over 4 per cent, the more usual figure being something under 2 per cent. Subsidiary to this, but of major importance in the future, was the extraction of the considerable quantities of zinc in the slag. At this stage little was known about the constitution of the slags apartfrom their chemical composition. Some early work on slag constitution was carried out in the B.H.A.S. Research Laboratories between 1919 and 1921, but except for a microscopic examination of a few thin sections the greater part of this investigation wasdevoted to the recovery of the zinc content of the slag by leaching methods.In 1949, therefore, it was decided to initiate a programme of fundamental research into the constitution and properties of the lead blast furnace slags. The information thus gained would give a clearer picture of reactions taking place in the slag, both in the blast furnace and during dezincing.There was also the hope that these results would lead to improved industrial techniques resulting in smaller lead losses, and, taking the long-term view, to efficient methods of producing zinc from the slags.A series of investigations was therefore begun at various centres over a period of time. These were:1. A mineralogical examination of the slags by Dr. A. B. Edwards of the Mineragraphic Section, C.S.I.R.O.2. A study of the thermodynamics of various slag com...

Jan 1, 1956

By M. Fan

Froth flotation is the most widely-used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubble on the flotation performances of different particle size fractions of coal was investigated using a bank of 10-liter flotation cells, a specially designed 50 mm inside diameter column and a 152 mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during coal froth flotation process improved flotation efficiency. The use of nanobubble in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.

Jan 1, 2012

By R. C. Ellman

Since successful industrial lignite-burning equipment was developed in 1925, the commercial use of lignite as a fuel for power plants has increased. It has proved an entirely satisfactory fuel for generating power and can be burned efficiently by various methods.4/ Equipment to fire pulverized lignite was installed and used successfully at the Trinidad Station of the Texas Power & Light Co. as early as 1926. The lignite was predried in steam-heated grid driers before pulverizing.5/ This method of firing was used later in the Comal Station of the San Antonio Public Service Commission.6/ Both stations, however, have since been converted to use other fuels. Units for pulverizing and drying lignite are relatively new in the lignite-consuming region of North Dakota. The air which sweeps the pulverizer and transports the pulverized product to the burners is preheated to dry the lignite during pulverization. The first unit was installed in 1948 in one of the two boiler units of the Crookston Station, Otter Tail Power Co., Crookston, Minn.7/ In 1951 the 30,000-kw. W. J. Neal Station, Central Power Electric Cooperative, Inc., Voltaire, N. Oak., was designed and constructed for firing pulverized lignite exclusively. It is the largest lignite-fired, power-generating station in North Dakota. The 44,000-kw. Lewis and Clark Station of the Montana-Dakota Utilities Co., Sidney, Mont., is fired by a similar pulverizing system. Operation of this plant was begun in October 1958. At Fergus Falls, Minn., the 53,500-kw. Hoot Lake Station of the Otter Tail Power Co., also using a pulverized lignite-firing system, began operating in September 1959.

Jan 1, 1961

By Herbert L. Lines

This paper is one of a series on mining and milling methods and costs published by the Bureau of Mines. The Ash Peak mine of the Veta Mines, Inc., Duncan, Ariz., is of particular interest in that the only metal of commercial value in the ore is silver. The silver is concentrated by flotation; the concentrate is shipped to a smelter for treatment.

Jan 1, 1940

By M. R. Smith, H. Kanli

The impact crusher is a popular device for producing crushed aggregates from non-abrasive rocks such as limestones, offering the advantages of high reduction ratios and relatively low installed costs. To extend the application of a process-flowsheet simulator to the quarrying industry, a mathematical model of an impact crusher was therefore developed using the general crusher models of Andersen and Whiten as a basis

Aug 1, 1995

By Trevor R. Ellis

"The valuation of mineral properties in the U.S. is only partially regulated. The regulations which have jurisdiction or impact appear to have such mainly as a consequence of unintended fallout, since the regulations were designed for other purposes. Court case history can also be important. The combined results are a mixture of bad and good, with important lessons to be learned.Since 1981, the Securities and Exchange Commission has prohibited U.S. listed companies from reporting quantitative estimates of mineralization and the value of mineralization, other than proven and probable reserves. This results in the minerals appraiser (valuator) working with a shortage of data in his everyday work, both on the subject property and in sales analysis.Between 1989 and 1995, all 50 states and essentially all Federal agencies adopted the Uniform Standards of Professional Appraisal Practice (USPAP) for real property appraisals (valuations). The major national appraisal societies also require their members to abide by USPAP. A significant portion of minerals appraisals must now follow these standards. This paper will discuss the content of USPAP. It provides a very good framework for the valuation of a minerals property or a mine, both as real property and as a business. However, the credentialing standards for real property appraisers are now prohibitive for minerals appraisers."

Jan 1, 2003

By Carl L. Bieniewski

In a Bureau of Mines supply evaluation, the known uranium resources in the United States are estimated to have a total recoverable uranium oxide (U3O8) content of 3,132,400 tons at prices up to $69.32 per pound. Only those resources were evaluated for which sufficient quantity data are available and process technology exists for recovering uranium. A total of 160,800 tons of U3O8 is available at $8 per pound from ore deposits presently mined and an additional 244,700 tons available at prices up to $30 per pound from similar but usually lower grade deposits. A total of 2,726,900 tons of U3O8 is available from four other resources: copper leach solutions, wet-process phosphoric acid, Florida phosphate rock Leached zone, and Chattanooga Shale. These resources contain from 30,000 tons of recoverable U30, at a price of $7.52 per pound as a byproduct of copper leach solutions to 2,557,300 tons at a price of $69.32 per pound from Chattanooga Shale.

Jan 1, 1971

By Stephen C. Tadolini

PC-Strand tendons, commonly referred to as cable bolts, have become a major rock reinforcement device for underground mining and civil applications. The most common configuration is a 1+6 strand, which designates a center king-wire, with six outer wires wound around it to form a 0.6-in (15-mm) diameter cable. The capacity of this tendon approaches 30 tons, but the performance is largely dependent on the anchorage medium and the ability of the system to transfer stresses back into the rock mass while reinforcing and suspending the immediate roof. Recent developments to improve the transfer mechanisms of the PCstrand via the anchorage medium by impregnating the individual wires with uniquely designed deformations have resulted in improved anchorage and subsequent cable bolt performance. This paper describes a series of laboratory tests used to develop the initial indentation patterns and numerical modeling simulations that were undertaken to refine and optimize the final designs. The new, indented PC-Strands, offered in both bright and properly galvanized, have been tested in the field and are being used effectively in two new cable bolt products. The results of the laboratory, computer modeling, field testing and in-situ installations provide a glance at the next generation of cable bolts. This suite of testing shows how they will improve the safety and serviceability of openings under adverse ground conditions.

Jan 1, 2012

By F. J. Chernosky

Most previous studies of coal flotation utilized chemically pure reagents. Since such reagents are not available in quantity, a study of various wmmercially available reagents as frothers was undertaken. Flotation procedures similar to those used in a large number of commercial coal flotation plants were employed. The reagents used were compared on yield-selectivity-wst basis. The selectivity was found to be relatively constant with yields above 70% but the reagent cost varied greatly. The types of reagents available were compared. In the past, a number of papers have been written on the use of various reagents as coal flotation frothers. For the most part, these have been an attempt to correlate the intrinsic chemical and physical proper- ties of the reagents or reagent groups to the floata-bility of various fine coals. Because of the type or nature of evaluations made, chemically pure reagents were normally used. Generally, these reagents are unavailable in commercial quantities. Therefore, the results obtained with these reagents were usually limited in usefulness to the plant operator or metallurgist. This paper presents the results of a study in which commercially available forms of various reagents were used as flotation frothers. Flotation procedures which would conform in general to those employed in a large number of commercial coal flotation plants were utilized. The objective of the test was to compare these reagents on yield-selectivity-cost basis, that is, 1) the yields obtained, 2) the ash levels obtained and 3) the reagent cost relating to these results. REAGENTS The reagents employed have been grouped into the following chemical classes: 1) aliphatic alcohols, 2) terpines, 3) glycols (synthetic water-soluble

Jan 1, 1963

By Oy Leuangthong

Red Dog mine is the world's largest Zn producer. The deposit consists of sulphide ore zones in sedimentary exhalative (sedex) deposits, and is characterized by the presence of multiple metals and multiple ore types. The objective of the case study is to characterize seven different minerals, Zn, Pb, Fe, Ba, sPb, Ag and TOC, within eight different rock types. Geostatistical models were constructed for each variable within the eight rock types, and subsequently assembled to give 40 realizations for six 25ft benches. The stepwise conditional transformation was used to account for the complex multivariate relations. In addition to reproducing the input data, histogram and variogram, the resulting models also respect multivariate relations locally and globally. This paper documents the methodology to construct these models. A thorough validation procedure was implemented. Comparisons with blasthole data show that the conditional simulations and the long-term models agree in expected value. The main advantages of the conditional simulations are (1) the explicit accounting of multivariate relations between the data in model construction, and (2) the ability to quantify variability and uncertainty at any scale. A small exercise comparing the profit from a kriged and a simulated model is also examined. Results show that the simulation approach showed a 3% increase in profit, relative to the conventional estimation approach.

May 1, 2004