Search Documents

By Friedel. Michael J.

The U.S. Bureau of Mines investigated acoustic emission (AE) and the Kaiser effect in six types of rock: St. Cloud gray granodiorite, Barre granite, Dresser basalt, Salem limestone, Berea sandstone, and a volcanic tuff. AE signatures were used for interpreting the rock deformation stage and for indicating mechanisms of failure in uniaxial compression. The research demonstrated the advantages of using the volumetric stress-strain curve, as opposed to the more conventional uniaxial curve, for correlating AE response signatures with deformation stages and fracture processes in the rock. Standardized experimental procedures were used for the AE monitoring. The Kaiser effect was shown to be capable of determining prestress levels to within a few percentage points in uniaxial compression tests. Also, prestress memory was shown to be retained in the rock for periods of up to at least. 5 months, the maximum period of testing. The Kaiser effect AE technology holds promise for providing a comparatively inexpensive and less complex method for examihing stress history in rock. However, since the conftning stress has a pronounced influence on the Kaiser effect, it must be considered in developing technology for determining peak fteld stresses based on the Kaiser effect.

Jan 1, 1990

By K. E. Livo, D. H. Knepper

Modern remote sensing provides a means for locating and characterizing exposed mineralized systems in many parts of the world. These capabilities are non-invasive and help target specific areas for more detailed exploration. An example of how remote sensing technology can be used is evident from a study of the Questa Mining District, New Mexico. Analysis of low spectral resolution data from the Landsat Thematic Mapper satellite system clearly shows the region-al distribution of two broad mineral groups often associated with mineralized systems: clay-carbonate-sulfate and iron oxides-iron hydroxides. Analysis of high spectral resolution data from the Airborne Visible and Infrared Imaging System (AVIRIS) shows the occurrence and distribution of many individual mineral species that characterize the pattern of hydrothermally altered rocks in the district.

Jan 1, 2004

The uptake of nickel into the lattice of pyrrhotite, Fe1 _1J S was studied experimentally in the temperature range 200°C to 760°C. Nickel from both aqueous solutions and salt melts diffuses rapidly into the sulphidelattice with an accompanying release of iron into the solution or melt. The rate of uptake of nickel and its diffusion into the sulphide lattice were followed by optical microscopy and by analysis with an electron probe microanalyser. Some geological consequences of this phenomenon affecting the distribution of nickel in rocks associated with nickel-iron sulphide ores are discussed.

Jan 1, 1972

By N. V. Nayak

Maharashtra State Road Development Corporation Ltd., has initiated a scheme for construction of 55 flyovers in Mumbai in India. To ensure speedier completion of projects several new technologies were adopted to save time without compromising on safety and reliability. Many of the flyovers involved large diameter pile foundations carrying loads ranging from 3500kN to 1375kN. Significant time would have been lost in using conventional load testing procedure to check pile capacity apart from the difficulty in mobilizing the load and the obstruction to site movement and traffic on the adjoining roads. High Strain Dynamic Testing was introduced on the project sites in lieu of static load testing after conducting numerous co-relation studies on various project sites. A total of seven co-relation studies have been conducted till date and based on these data static testing has been replaced by dynamic testing on numerous flyovers. The paper presents the results of such studies. CAPWAP analysis was also conducted on the data to evaluate the percent skin friction and end bearing so as to improve future design parameters.

Jan 1, 2000

A pyrite flotation concentrate assaying 0·065 oz/ton gold was investigated to determine the mode of occurrence of the gold. Ftom cyanidation and acid leaching experiments it was concluded that O· 02-0· 03 oz/ton goldwas in solid solution in pyrite and the balance of the gold was finely dispersed as grains throughout the pyrite.Autoradiography and electron-probe examination of possible areas in briquetted concentrate did not detect any grains of gold. Neutron irradiation and gamma spectrometry confirmed on 100 mg samples the fire assays obtained on 1 assay ton samples.Oxidation to hematite and reduction to magnetite at 600°C made practically the whole of the gold extractable by cyanide. This technique could be of major significance for gold ores which contain a substantial amount of "refractory" gold.

Jan 1, 1969

By Daniel Hodouin, Claude Bazin

"A graphical method to assess the size reduction by grinding is presented and illustrated with data collected from laboratory grinding tests and industrial grinding circuits. The method lies between the graphical comparison of size distributions and the population balance model. The method is easy to apply and provides a quick way to compare grinding mill performances under various operating conditions and processed ores. The application of the method to industrial mills shows that a grinding mill operation could present an invariant behaviour that can be exploited for simulation purposes.INTRODUCTIONThe size reduction of particles by grinding has been studied for decades and several books were published on the subject. Most of the recent studies focus on the modelling of the ball, semiautogenous and autogenous grinding mills operation (Napier-Munn et al., 1996) because accurate simulators can be used for design, optimization and control. Although the development of realistic simulators is progressing, the trial and error method is still used by many operators to identify optimum operating conditions for a grinding machine.Laboratory tests allow the characterization of the material submitted to grinding and the analysis of various operating conditions, such as ball size or shape, mill speed and slurry concentration of solids, on particle size reduction. Similar tests can be conducted in a plant, but results are often difficult to analyze due to errors associated with sampling and sensor accuracy. This paper presents a graphical method to assess the degree of size reduction carried out by a grinding machine. The paper consists of three sections. The first section describes the method and the following sections illustrate the method with data taken from laboratory and industrial grinding machines."

Jan 1, 2004

By S. F. Diehl

Weathered mine waste consists of oxidized primary minerals and chemically unstable secondary phases that can be sources of readily soluble metals and acid rock drainage. Elevated concentrations of metals such as Cd, Cu, Fe, Mn, Ni, Pb, and Zn are observed in deionized water-based leachate solutions derived from complex sedex and Cu-Pb-Zn mine wastes. Leachate (USGS FLT) from the Elizabeth mine, a massive sulfide deposit, has a pH of 3.4 and high concentrations of Al (16700 ug/L), Cu (440 ug/L), and Zn (8620 ug/L). Leachate from the sedex Faro mine has a pH of 3.5 and high concentrations of Al (2040 ug/L), Cu (1930 ug/L), Pb (2080 ug/L), and Zn (52900 ug/L). In contrast, higher-pH leachates produced from tailings of polymetallic vein deposits have order of magnitude lower metal concentrations. These data indicate that highly soluble secondary mineral phases exist at the surface of waste material where the samples were collected. Sulfide minerals from all sites exhibit differential degrees of weathering, from dissolution etched grain rims, to rinds of secondary minerals, to skeletal remnants. These microscale mineral-dissolution textures enhance weathering and metal leachability of waste material. Besides the formation of secondary minerals, sulfide grains from dried tailings samples may be coated by amorphous Fe-Al-Si minerals that also adsorb metals such as Cu, Ni, and Zn.

Jan 1, 2011

By A. J. Thompson

The Metropolitan Transportation Authority (MTA) East Side Access project (ESA) will, when it is complete, provide a new link to the east side of Manhattan from Long Island, NY that, linked with the Second Ave. Subway currently under construction, will assist in relieving overcrowding at Penn Station as well as the Lexington Ave. subway. ESA will bring Long Island Railroad (LIRR) directly from Long Island into a new station located 37 m (120 ft) beneath the existing Grand Central Terminal (GCT) located in the heart of Manhattan. It will connect the LIRR?s mainline tracks in Queens, via the existing 63rd Street Tunnel under the East River, to a new terminal constructed within, and beneath, the historic Grand Central Terminal.

Jan 1, 2012

By W. R. Herrera

A research effort was conducted to present or develop methodology for evaluating candidate potting materials intended for use in explosion-proof enclosures. The primary purpose was to develop acceptance guidelines based on arc decomposition products. Acceptance criteria can be based on: ? Inherent thermo-chemophysical, mechanical and electrical properties; ? Arc decomposition products: ? Nature of volatile products produced, e.g., flammability, explosivity, synergistic effects on existing environment in the enclosure, toxicity; ? Quantity produced as a function of arc power and duration; ? Acceleration aging tests to evaluate breakdown under electrical stress.

Jan 1, 1982

By W. W. Roepke

The linear cutting system, developed by the U.S. Bureau of Mines, uses geometric principles developed by Cardan to produce a nearly constant cut depth. The new system has been extensively tested in a synthetic material under laboratory conditions to verify mechanical capability and to identify operational characteristics. Comparisons between 15-rpm linear cutting and 50-rpm rotary cutting systems show significant improvement in respirable dust entrainment, product size distribution, and energy usage. Respirable dust is reduced by as much as 90 pct. Recovered product showed a 67-pct reduction in -0.32-cm (-1/8-in) material and a 200-pct increase in +5.08 cm (+2 in) material. Average power was reduced by 66 pct for the linear cutting. Because the bit cutting paths differ between linear and rotary cutting, it was necessary to compare the two at the same cut depths and bit types. These comparisons show that low revolution per minute rotary cutting entrains about the same amount of respirable dust as the linear cutting system, but the average shaft torque may be 55 to 130 pct greater for the rotary system.

Jan 1, 2010

By Paul F. Grundy

The ever changing conditions in the coal-mining industry and the increasing competition of other fuels such as oil, natural gas, wood refuse, etc., have made it imperative that the coal operator be in a position to supply a constantly uniform and clean product. The old idea of putting on the market "anything so long as it's black" no longer holds good. Today's users of fuel have to consider the amount of heat per dollar they obtain from the fuel they buy. Burning of coal has become largely mechanical, at least so far as industrial coal is concerned, and industrial coal is the kind the bituminous operator is for the most part called upon to supply. When we get into things mechanical, the matter of precision has a mighty bearing on efficiency. Precision in coal means standardization of quality, or uniformity of preparation in size and also in ash and moisture content. The trend of coal mining is ever towards more and more mechanization. Mechanization means coal-cutting machinery, loading machinery, conveying machinery, etc. Although such methods cut the cost, the cleanliness of coal so mined and loaded is not controllable to the same extent as when each operation is by hand labour. The operator has therefore the problem of mining his coal as cheaply as possible, but at the same time preparing a product which will to the utmost satisfy his customer. The answer is a mechanical cleaning plant. Before installing a cleaning plant, however, the operator must take into consideration the cleansability of the coal from his particular mine. This is accomplished by taking representative samples of the seam or seams to be treated, and subjecting these to screen tests, followed by float and sink tests on each size product. From these tests, it can be readily found to what degree of cleanliness the several sizes can be prepared advantageously, and also what will be the percentage recovery of cleaned coal. The accompanying tables give the results of representative tests on Michel coals of minus-2-inch size. All coal over 2-inc.h was intended to be hand cleaned. The coal-cleaning plants in general use at the present time come under two broad classifications, namely, wet and dry.

Jan 1, 1934

By J. P. Walsted

Offgrade chromite concentrate, with a Cr-Fe ratio of 1.3 to 1.4 has been successfully smelted to produce useful ferroalloys. The Cr-Fe ratio is not improved, but the alloys can be used without a too drastic change in normal steel-mill practice. The ordinary high-carbon ferrochrome has been successfully produced by smelting under highly acid smelting conditions. An alloy containing 50 percent chromium was produced at a power consumption of 4,490 kw.-hr. per ton of alloy. Alloys containing 20 percent silicon were made by direct smelting chromite concentrate and silica.

Jan 1, 1956

By Herbert H. Kellogg

The chemistry of sulfide roasting is analyzed to show those aspects of performance which Thecan be predicted from considerations of thermodynamic equilibrium. It is concluded that equilibrium calculations can serve as a yardstick for prediction of roaster-gas composition and sulfate formation in the calcine for fluid-bed roasting practice. A method of calculation which combines the equilibrium and stoichiometric factors is outlined, and illustrated by an example from the roasting of Cu-Fe sulfides. ON first examination the roasting of sulfides would not seem to be a process to which equilibrium calculations could be applied to yield results of practical value. The burning of sulfides is an ex-tremely spontaneous reaction, excess air is always used to obtain rapid reaction, and in most traditional roaster designs (hearth roasting) the temperature and gas composition vary widely from point to point in the roaster. These are all conditions which promote a non-equilibrium state in the roasting process. However, the introduction of the fluid-bed roaster1 has brought to roasting practice new conditions of operation, so that equilibrium calculations can be used to predict certain limited aspects of practical operation. The fluid bed is characterized by uniformity of temperature, gas composition, and calcine composition from point to point throughout the bed. These relatively uniform properties of the bed make the meaningful calculation of the equilibrium state of certain reactions in roasting possible. It is the purpose of this paper to analyze roasting from an equilibrium viewpoint, to show where the method may be expected to yield valuable information, where it fails, and to outline methods of calculation. Main Roasting Reaction The reaction MS (s) + 3/2 0, = MO (s) + SO, [I] might well be called the main roasting reaction. It adequately accounts for the well known facts that metal sulfide and air are the main reactants, and metal oxide and SO, the main products. Deviations from this simple stoichiometry will be discussed under side reactions. For all metal sulfides, Reaction 1 is strongly exothermic and the equilibrium position is far to the right. Since the reaction is exothermic, the equilibrium shifts in the right-to-left direction as the temperature is raised. However, at all practical roaster temperatures (between 500" and 1200°C), the amount of this shift is small, and the equilibrium position remains far to the right. The main roasting reaction is essentially irreversible, and the application of equilibrium considerations to this reaction will not be! a fruitful field of investigation. A knowledge of the rate of this reaction. although not the proper subject of this paper, is of great importance to the roasting process. Analysis of the factors which influence this rate shows that: 1) The rate will increase rapidly with increased temperature. 2) The rate will be proportional to the partial pressure of oxygen at the surface of the reacting particle. Because of diffusion effects, the partial pressure of oxygen at the particle surface may be considerably less than in the bulk of the roaster gas. For this reason, intimate contact between gas and solid and high relative velocity between gas and solid, such as can be obtained in a fluid bed or flash roaster, will markedly increase the rate of reaction. 3) The rate will be proportional to the surface area of metal sulfide. Therefore, smaller particle size will permit a more rapid rate per unit of weight. To achieve practical rates of roasting the partial pressure of oxygen in the roaster gases must be maintained at a finite level at all times. Even where the gas-solid contact is very good, as in the fluid-bed roaster, the oxygen content of the gas must not be allowed to drop below some limiting value (perhaps 1 pct), or the rate of the main roasting reaction will become too small for practical operation. Side Reactions in the Gas Phase The gas phase during roasting of metallic sulfides contains the elements oxygen, sulfur, nitrogen, by-

Jan 1, 1957

By Matters, R T, Coldham, Slee, J C, R J, Wallman

The Committee desires to thank the managers of the various mines along the line of lode for their hearty co-operation in its labours. It would also extend thanks to Messrs J C Moulden, Howchin, Twelvetrees, and the West Australian Geological Surveyfor various information; to Messrs J G Dreyer, S Pope, T Read, P Moncrieff, R Williams, and W J Rose for analyses; and to a number of local gentlemen for advice and help. Professor Skeats, of Melbourne University, gave much valued assistance in petrology, and Mr Herbert Lavers kindly undertook the study of the garnets.INTRODUCTIONThe famous Broken Hill lode is situated in a low range of hills, the Barrier Ranges, near the western border of New South Wales. It has been worked since 1884-fust for silver, then for silver and lead, and at present for lead, silver, and zinc...

Jan 1, 1910

By Joseph M. Kuchta

The limits of flammability and minimum autoignition temperature of a fuel are important elements in assessing fire and explosion hazards that may exist when using or handling the fuel. The limits of flammability define the range of compositions of the fuel gas or vapor mixed with an oxidant through which a flame, initiated by an outside energy source such as an electrical spark, can propagate. The minimum autoignition temperature (M.A.I.T.) is the lowest temperature at which the fuel vapors ignite spontaneously in a specified medium; in this case the ignition energy is supplied by the heat content of tae environment. This temperature is also referred to as S.I.T. value by some authors. Because the autoignition of a fuel also depends on the time interval during which the fuel is subjected to heat, ignition delays are significant. Ignition delay is defined here as the total time elapsed between the introduction of the liquid fuel into the oxidizing atmosphere and the appearance of a flame. This time interval includes both the physical and chemical processes leading to ignition. The ignition delay is usually maximum at the M.A.I.T, and decreases as the temperature of the system is increased. The flash point and the fire point are also useful in assessing the fire and explosion hazards of a fuel. The flash point is the lowest temperature at which saturated, flammable fuel vapor-air mixtures are formed at atmospheric pressure and, therefore, it is essentially the lower limit of flammability

Jan 1, 1962

By L. Nahai

An important objective of the Australian Government's policies on resources development is to encourage further processing of raw materials domestically, to the extent that this is economically feasible and consistent with sound industrial development. This Bureau of Mines report examines the extent to which Australia is able to pursue this policy in terms of its own competitive advantages and the implications of such a policy for the United States. Such factors as the impact of other competing producers and their advantages, expected world demand, and infrastructural problem--which may limit pursuit of this policy to the fullest extent--are discussed. After a broad review of the re-source, economic, social, and environmental factors, the perspective for increased processing is examined for a number of mineral commodities.

Jan 1, 1982

By T. Hudaverdi

Control of the particle size distribution of a muckpile after blasting is always an important subject for mining industry. Blasting has a significant impact on downstream processes such as loading, crushing and grinding. Improvement of blasting results provides increase in loader and excavator productivity due to increased diggability capacity, and increased bucket and truck fill factors. Suitable and uniform particle size distribution results increase in crusher and mill throughput and decrease in energy consumption in size reduction process. Digital image analysis technique has been used for many years in mining industry in order to determine blast fragmentation. The images of muckpile surface can be used to determine the mean fragment size (x50). The source of digital images can also be haul truck, leach pile, waste dump, stockpile, and conveyor belt. The screening that is conventional method to measure blast fragmentation is time consuming and expensive. Digital image analysis is a cost effective and faster method (1).

Jan 1, 2012

By Y. Zhoa

The surface morphology of materials is of fundamental importance to many surface related applications, such as wetting, friction, reflection, drag, and adhesion. Various approaches for micro/nano patterning atop polymer surfaces have been proposed in recent years. However, a cost effective technique is still highly in demand. In this paper, we demonstrate a novel but rather simple and generic approach for surface micro/nano patterning using shape memory polymers (SMPs). Different types of novel patterns are realized and their 3-D surface features are quantitatively analyzed by a PLµ Confocal imaging profiler.

Jan 1, 2010

By Robert E. Fosse

Driven 14-inch-square concrete piles were used as the foundations of Genentech Hall at the new University of California, San Francisco Mission Bay Campus. The five-story, steel eccentrically-braced frame building is currently under construction at a 43-acre property located in a former large shallow marshy inlet from San Francisco Bay. The piles were driven through 10 to 25 feet of fill and 20 to 60 feet of soft compressible Bay Mud into an underlying dense sand layer. Pile design capacities were developed for traditional allowable stress design, load factor and resistance design, and ultimate design criteria. The ultimate level capacities were for checks of loads occurring when the links in the eccentrically-braced frame yield during an earthquake. A load test program was performed to confirm pile design recommendations. Two test pile locations were selected for compression, tension, and lateral load tests to evaluate pile capacity and pile/soil stiffness under long-term, short-term and rapid loading conditions. Maximum test loads were 1000 kips downward, 350 kips uplift and 50 kips lateral. Foundation construction began by driving 34 indicator piles with a Delmag D46-32 diesel hammer of 113 foot-kips maximum rated energy. All indicator piles were monitored during initial driving using the Pile Driving Analyzer. Restrike data, obtained several days after initial driving, indicated significant pile-soil setup and typical pile capacity increases from 750 to 1000 kips. The majority of the 1242 production piles were then driven to acceptance criteria of 75 blows per foot and a minimum embedment of 10 feet into the dense sand bearing layer. Piles driven to full length without achieving the blowcount criteria were evaluated on a case-by-case basis. Acceptance of these piles was established by evaluating restrike data.

Jan 1, 2002

By Fisher N. I

Disequilibrium ratios (U3O8/eU3O8), which assess the degree to which gamma activity represents the uranium content of a sample, have been measured on a representative set of samples from the ore zone of a carnotite ranium deposit located at Yeelirrie, Western Australia. A statistical analysis has been performed to investigate the dependence of the ratios on lithology and on the location of the sample in the orebody. The analysis indicates that dependence on lithology and on position across the orebody is negligible. Samples from the western end of the orebody and those from below the water table level tend to have slightly lower ratios than samples from other positions, although these trends are small compared with a large random variation in the data. The large random variation could result from some redistribution of the daughter isotopes of uranium within the orebody. On the basis of the results from all the samples, the estimated deficiency of uranium relative to radium in the ore zone of the deposit is 11 per cent.

Jan 1, 1980