Search Documents

In a previous paper of this series (1) ,t it was shown that during the creep of single crystals of lead, deformation proceeded to some extent by means of slip on the octahedral plane. This was demonstrated by the formation of slip lines on the surface of the specimens. At first, a few broad bands appeared after a small amount of extension had taken place; then, as extension proceeded, more and finer lines made their appearance until the whole of the specimen surface was covered.The present paper deals with the process of deformation of the creep specimens as revealed by X-ray examination..By the use of this method, the changes taking place in the crystal structure can be observed.EXPERIMENTAL METHODThe method of preparation of the specimens, their size and the purity of the lead employed have been reported elsewhere (1). At frequent intervals, the specimens were dismantled from the test rack and X-ray back reflection photographs were taken. The specimens were so marked and set up on the X-ray machine that the same spot on the specimen surface was always examined.Copper radiation was employed, the tube voltage and current being 45 kV. and 25 m.a. respectively and the exposure time 2 hrs. The slit diameter was 1 mm.

Jan 1, 1941

By Alicia Esther Ares

The family of Zn-Al (ZA), Zn-Ag and Zn-Al-Ag (ZINAG) alloys offers high mechanical properties, ease of finishing, the advantage of low energy and pollution-free melting. Also, present alternatives to the well developed alloy systems, such as brasses, bronzes, cast irons and aluminum alloys. The main objective of this paper is to measure thermal parameters in ZA, Zn-Ag and ZINAG hypoeutectic and hypereutectic alloys directionally solidified which present columnar, equiaxed and columnar to equiaxed transition structures (CET). Also, estimate the mechanical properties, such as microhardness and tensile parameters and correlate these with the thermal (cooling rate) and structural parameters (grain size and dendritic spacing). The different types of structures were analyzed with optical and scanning electron microscopy. The results showed the influence of concentration, microstructural arrangement and thermal conditions during solidification on the mechanical properties. The results of the present investigation are compared with previous experiments.

Jan 1, 2010

By W. W. Adams

"The ninth yearly National Safety Competition covering the calendar year 1933, conducted by the United States Bureau of Mines, w participated in by 332 mines and quarries situated in 35 States. Enrollment represented as increase of 10 plants over 1932, and one addition was made to the number of States represented.The primary purpose of the United. States Bureau of Mines in conducting the contest is to promote safety in United States mineral industries. This purpose is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive recognition on a national scale for their achievement the purpose is accomplished indirectly through studies by the United States Bureau of Mines of the facts contained in the accident reports the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics which constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting, from industrial accidents.Bronze trophies, known as 'Sentinels of Safety', which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines, were presented to five companies in the contest of 1933, each company having established the best accident-prevention record within one of the five classes into which all companies were divided, namely, anthracite-mining companies, bituminous-coal-mining companies, metal-mining companies, operators of nonmetallic-mineral mines other than coal mines, and quarries or opencut mines. The trophies are awarded for 1 year and are then transferred to the winners of the succeeding year's contest.The trophy for bituincus-coal mines was won by a company in Wyoming. A company in Tennessee won the trophy for metal mining. In the nonmetal-mine group the trophy was again won by a company in New York. A quarry in Michigan won the trophy for the quarry-and-opencut-mine group. The trophy for anthracite mines remains in Pennsylvania, as all anthracite mines in the contest are in that State."

Jul 1, 1934

By L. Rademan

The kinetic leaching behaviour of a low-grade surface gold ore and a high-grade reef ore were evaluated to determine the achievable gold recovery from these ores and particularly mixtures of these ores. The reef ore material has a head grade of 13.40 g/t with a relative standard deviation of 3%, and the unprocessed surface ore material a head grade of 0.43 g/t with a relative standard deviation of 15.6%. It is concluded that the kinetic leaching behaviour of these free milling gold ores during cyanidation, is not influenced by mixing of reef and surface ore material. No statistically significant relationship exists between the achievable recovery by direct cyanidation and the head grade of the material fed. No ideal ratio of surface ore to reef ore could be established. It is recommended that these materials should be processed simultaneously to minimize the costs, security risks, and losses incurred in transportation.

Jan 1, 2012

The Broken Hill orebody ,occurs in the Willyama Complex, a block of Precambrian rocks which have been strongly folded and metamorphosed at moderate to high grade. Although -the origin of the silver-lead-zinc mineralization remains obscure, recent investigations have substantiated the view that the orebody has undergone concomitant high grade metamorphism with the enclosing wallrocks. The mesoscopic structures produced by this metamorphism are described, and the possible processes Telating to their formation are disoussed.In the high grade ore, metamorphic structures which can be recognized are foliation and lineation, wallrock fragments, layering, flow folds, ore breccias, and sulphide bearing veins. These structures can be related to processes involving plastic flow and fluid phase transport of the mineral assemblage. 'In areas of low grade mineralization adjacent to high grade ore, the structures more closely resemble those produced in -the wallrocks-foliatlon, lineation, layering, folds, and sulphide injections. Within areas of high grade ore, lenses and pods of manganese silicates Probably represent original inhomogeneities in the ore, i.e., portions of manganese-rich and sulphide deficient rock which have been metamorphosed to manganese silicates.From the structures displayed, a sequence of events has been established for the plastic flow of ore during deformation.

Jan 1, 1975

Characterization of ore and waste-rock material using automated quantitative micro-mineralogical techniques (e.g., QEMSCAN® and MLA) has the potential to complement traditional acid-base accounting and humidity cell techniques when predicting acid generation and metal release. These characterization techniques, which most commonly are used for metallurgical, mineral-processing, and geometallurgical applications, can be broadly applied throughout the mine-life cycle to include numerous environmental applications. Critical insights into mineral liberation, mineral associations, particle size, particle texture, and mineralogical residence phase(s) of environmentally important elements can be used to anticipate potential environmental challenges. Resources spent on initial characterization result in lower uncertainties of potential environmental impacts and possible cost savings associated with remediation and closure. Examples illustrate mineralogical and textural characterization of fluvial tailings material from the upper Arkansas River in Colorado.

Feb 27, 2013

This paper has peen translated from the Russian by the United States Bureau of Mines and is issued as one of a series of circulars dealing with mining methods and costs in connection with a general study of this subject sponsored by the bureau. The paper presents some interesting features in connection with the methods employed in Russia and describes certain variations in standard methods which might conceivably be applied to a limited extent in this country.

Jan 1, 1930

By C A. Locke, J Cassidy, J L. Mauk

The Waihi-Waitekauri region hosts numerous low-sulfidation epithermal deposits that both outcrop and occur at depth. Zones of intense hydrothermal alteration enclose the Au-Ag bearing quartz vein deposits. Hydrothermal alteration includes the destruction of magnetite by hydrothermal fluids, pervasive silicification adjacent to quartz lodes and potassium enrichment due to adularia and illite deposition. High-resolution airborne magnetic and radiometric, and new gravity data delineate distinct geophysical anomalies associated with hydrothermal alteration and mineralisation. Five magnetically quiet zones occur in the region varying in size from 3 to 34 km2 and in geometry from circular to irregular zones. These zones represent the near-surface extent of strong to intense hydrothermal alteration associated with fossil geothermal systems. All epithermal deposits in the region occur in magnetically quiet zones. Over 120 new gravity stations together with existing data across the Waihi district have defined a positive Bouguer gravity anomaly coincident with the magnetically quiet zone. Eastern and western gradients of 50 gu/km bound the anomaly that contains two flat gravity highs west and east of the Waihi deposit. Strong potassium signatures in airborne radiometric data correlate with outcropping zones of alteration and are consistent with the presence of adularia and illite minerals. Hydrothermally altered zones are represented by areas of low Th/K ratios as a result of low thorium concentrations in andesite and elevated potassium levels in altered zones.

Jan 1, 2003

By E. Chin

The only economically significant mineral exploited in Banglades - during 1981 was natural gas. Nitrogenous fertilizer production was important to the agricultural sector and was totally dependent on the natural gas for fuel and raw material. Domestic cement plants were also fu pled by natural gas. The flat river-delta terrain for most of Bangladesh makes the potential for discovering major mineral deposits poor. No large deposits of metal ores have been found and only in the small hilly southeastern section of the country is there even much chance of finding any. Heavy mineral sand deposits may eventually be exploited along the Chittagong coastline. There is a good potential for crude oil discoveries. The Bangladesh economy has been heavi¬ly subsidized by billions of dollars of foreign aid since the country's inception. A World Bank report recommended total aid needs of over $2.6 billion in fiscal year (FY) 1980-81. It received commitments for barely over one-half that amount.

Jan 1, 1983

By James W. Myers

"Packaged fuel" is the trade name applied by the industry to a product consisting of coal screenings and a binder compressed into 3 -or 4-inch cubes and wrapped (six or eight in a package) in sturdy paper and sealed with gummed tape. Parry describes the product in greater detail and distinguishes clearly between packaged fuel and briquettes. The industry developed from the desire of retail coal dealers to improve utilization of the relatively large quantities of slack sizes that result from the degradation, during shipping and handling in the yard, of friable coal, particularly Pocahontas coal. During the war an attempt was made to apply this technique to anthracite fines, and a recent publication of the U. S. Bureau of Mines reported the results of physical and combustion tests on packaged fuels containing anthracite fines. References made in this report to the previous investigation on packaged fuels containing anthracite represent data or conclusions presented in Report of Investigations 3882. This investigation was conducted as a continuation of the previously reported studies and consisted of physical and combustion tests of packaged fuels made from high-volatile bituminous coal, as well as the low-volatile bituminous coal ordinarily used in the industry, to determine their relative suitability for domestic firing. Particular attention was given to the smoke-producing properties of the packaged fuels because of the increasing importance of the prevention or reduction of smoke from hand-fired domestic heating plants resulting from the widespread enactment of smoke-prevention ordinances.

Jan 1, 1951

In order to ensure safe mining and reduce surface damage in shallow multiple-seam mining, the failure characteristics of interburden strata with different coal pillar offset distances between pillars in the upper and lower seams, the distribution characteristics of stress concentration in coal pillars, and the development characteristics of stratum cracks and subsidence were physically investigated and also using UDEC2D software. Meanwhile, the effect of different coal pillar offset distances on the stress concentration of coal pillars and development of stratum cracks were studied. Based on those results, a formula for safe mining and reducing surface damage was established, which provided a theoretical basis for safe and environmentally friendly mining in shallow multi-seams. According to the results of the study, the optimal coal pillar offset distance (the side-to-side horizontal distance of the upper and lower coal pillars) between the upper and lower coal seams was developed to reduce the stress concentration of coal pillars and surface damage. The results of this study have been applied in Ningtiaota coal mine and have achieved good results in safe and environmentally friendly mining.

Jul 28, 2020

By P. Lafleur

All indications point to a growing market for thermal coal in Japan as part of the country's current energy policy formulation process. The Ministry of International Trade and Industry forecasts imports of 16 million tons a year in 1985 and 40 million tons in 1990-a twenty-fold and forty-fold increase over the present level. This potential reflects Japan's over-all serious and increasing concern for security of energy supplies and its resultant need to seek alternative sources. Nuclear power will be the main alternative source, but, because it is expected that its development will be slow, imported thermal coal will assume greater importance. Canada, with large resources of all types of coal, could fill a portion of this market. Thermal coal could come from specific thermal coal developments or from metallurgical coal mines, which usually produce a certain amount of coal not amenable to coking, but suitable for power purposes. However, penetration of this Japanese market by Canadian thermal coal will depend on the resolution of a number of problems. On the demand side, siting, environmental aspects, the need for a coal unloading and trans-shipment centre, and the added cost of installing coal-fired stations could be major constraints. Although Canada has ample high-quality resources, any new development tied to the Japanese market will require improvement in prices to cover the high costs associated with transportation, the construction of new mines and the provision of new infrastructure.

Jan 1, 1979

By D. Newman

Multiple seam mining is prevalent in Southern Appalachia because economically mineable coal seams are numerous and frequently occur in close vertical proximity. West Virginia, Kentucky, and Virginia have 117, 55, and 40 mineable coal seams respectively. It is extremely rare to have an underground mine that has not been undermined, overmined, or has mining adjacent to it. In many cases the multiple seam mining is concurrent with extraction sequenced in superjacent seams. Because underground mining is focused on recovering the most valuable reserves, mining is rarely practiced from the top seam down, which is the practice most conducive to stability. The combination of room-and-pillar mining methods that include development only, small block, partial retreat, full retreat, and longwall mining produce a wide range of mining geometries and complexity in underlying and overlying seams. In the future, the number of multiple seam operations will increase as reserves are depleted and future mines are, by default, located closer to abandoned mine workings. The improved coal market has transformed many formerally uneconomically mineable seams into attractive reserves. The approaches and methodologies used for multiple seam stability analysis are dictated by the site conditions, including overburden/interburden thickness and lithology, mining geometry, and the mining methods in both the active and abandoned mines. Multiple seam stability analysis using analytical and numerical methods is illustrated by two case histories that reflect close proximity room-and-pillar mining and mining in bump prone situations.

Jan 1, 2007

By Alan B. Wagner

The River Tower is a proposed 27-story condominium building in the heart of downtown Milwaukee, Wisconsin (USA). The tower will be over 100 m tall, and will have a ground area measuring 15 m by 40 m. The structure will be constructed of cast-in-place reinforced concrete. Certain transfer girders and stabilizing diagonals will be constructed of post-tensioned concrete. Vertical loads will be transmitted through an arrangement of columns, bearing walls, and elevator and stair cores. A mat foundation will be used to connect and integrate these load-carrying elements. The site's geologic profile includes 8.4 m of compressible estuarine (organic) deposits. To control settlement, the mat will be pile-supported. These deposits are underlain by moderate-strength inorganic deposits that extend to bedrock at 32 m.

Jan 1, 2002

By José L. M. Clemente, John R. Davie

"Abstract An extensive pre-production static and dynamic pile load testing program was conducted for a coal-fired power plant. The static load testing program included axial compression, uplift (tension), and lateral load tests. Three types of piles were tested: Monotube, closed-end pipe, and step-tapered. The load tests were used to (a) determine pile driveability characteristics for each pile, (b) verify pile load response behavior, and (c) provide data to support the selection of a cost-effective piled-foundation system for the plant. A recent publication (Clemente and Lewis, 2013) describes the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript describes site subsurface and groundwater conditions and installation of probe piles for testing, focuses on the uplift and lateral load testing program, and provides a comparative interpretation of the load test results.INTRODUCTIONThe pre-production probe pile load testing program described here was conducted for a 202-megawatt, coal-fired power and steam generating (cogeneration) facility. A schematic layout of the main plant (power block area) is shown in Figure 1, which also includes the locations of clusters of preproduction probe piles and boreholes drilled near these clusters.The load testing program included 24 pre-production probe piles driven throughout the power block area. The probe piles were driven at locations T-1 through T-8, shown in Figure 1. Three types of piles were driven at each location: Monotube pile; closed end, straight shaft pipe pile; and step-tapered pile. At each location, the three piles were driven in a row with the pipe pile at the center, and the center-tocenter spacing between piles was equal to about 1.5 m (> 3.5 pile diameters for the largest pile). No pile cap was used to connect the three piles, and the three piles driven at locations T-1 through T-8 will be referred to as pile clusters. A complete suite of static load testing (compression, tension, and lateral) was performed on each individual pile at Cluster T-2 and on the step-tapered piles only at Cluster T-8, shown in Figure 1.Clemente and Lewis (2013) provide details of the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript focuses on the uplift (tension) and lateral load testing program. A brief summary of the site geology and existing subsurface and groundwater conditions in the vicinity of the test pile clusters is presented, with emphasis on T-2 and T-8. Probe pile driving results at T-2 and T-8 are also presented. Descriptions of the static uplift and lateral load test program at T-2 and T-8 are given along with a comparative evaluation of the load test results."

Jan 1, 2014

By Richard W. Hanford

The geotechnical construction industry generally considers soil mixing to be defined as an in situ ground improvement or treatment method by which a dry or wet reagent is introduced into the ground and is blended with the soil by mechanical or rotary mixing tools. This results in relatively homogenous mixtures whose engineering properties are improved and are greater than the soil properties before mixing. Reagents usually include cement, but may also include processed clay such as bentonite, when a reduction in hydraulic conductivity is desired, or other proprietary chemicals when chemical stabilization is the objective. Mixing may be either shallow or deep. Shallow Mixing is the term arbitrarily used for treatment of soils within the upper 30 feet; Deep Mixing denotes treatment below 30 feet to the depth limits of the equipment. Mixing equipment may consist of single or multiple-shaft tools having cutting and mixing blades of many different configurations. To avoid using proprietary nomenclature, reference to Shallow Mixing Methods (SMM) and Deep Mixing Methods (DMM) are the preferred terms. Although originally developed and patented in the United States in 1956, in situ construction using various soil mixing methods is more prevalent in Japan and the Scandinavian countries. Reintroduced into the United States from Japan in 1986 for ground improvement and liquefaction mitigation at Jackson Lake Dam, Wyoming, acceptance of soil mixing methods has been gradual but slow. Applications typically include:

Jan 1, 2001

The increased focus on best practice environmental management has led to mining and mineral processing companies developing a variety of procedures to ensure that the environmental impacts of their operations are minimised, and that company managements are fully aware of these impacts and the policies and procedures established to ensure this process. Parallel to this, international standards for the development and implementation of environmental management systems are being promoted as necessary for companies to demonstrate their due diligence. Good environmental management systems should be built upon the systems already established within companies, and should ensure that the process of continual improvement is integral to their operation. An outline of the basic components of environmental management systems is provided, along with examples of the way various mining companies have implemented such systems. The benefits of best practice environmental management to mining companies are also considered.

Jan 1, 1995

By L. W. Kelly

The purpose of this paper is to indicate some of the benefits that have been derived in the Zeigler No. 3 mine by using roof bolts under extremely adverse roof conditions J with the thought that much better results could be obtained in other mines with more normal roof conditions by applying some of the practices that were developed in this mine. Some of the benefits that have been obtained in this mine, which will be shown in this paper, are: 1. Increased tonnage per man-shift at the face when roof bolts are used, as compared to the tonnage under similar conditions when conventional timbering methods were used. 2. Increased efficiency of roof bolting by giving the foremen a definite plan to follow. 3. Reduction in delays caused by failures of the trailing cables of loading, mining, and drilling machines. 4. Reduction in the number of accidents after roof bolting was adopted. Inasmuch as the success that followed roof bolting in this mine was obtained under one of the most treacherous roofs in the Middle West, it is reasonable to suppose that correspondingly better results could be obtained under more favorable roof conditions by using the same procedure.

Jan 1, 1952

By Khaled Morsy

In the past two decades, high horizontal stress has been attributed to many ground control failures. Most believe that entries parallel to the high horizontal stress is most stable and least stable when perpendicular to it. Entry stability decreases when the angle between entry and horizontal stress increases. The concept of 2-D stress shadow has been proposed for selection of proper panel orientation, often with mixed results. In this paper 3-D finite element modeling was used to analyze the stress distribution at the headgate of a longwall panel subject to high horizontal stress at various angles. It was found that the directions of induced principal stresses at the longwall face and headgate are independent of the panel orientation. The induced principal stresses concentrate or relief at headgate based on the panel orientation with respect to the directions of the induced principal stresses. Accordingly, only 3-D modeling can fully account for the effects of high horizontal stress on panel orientation. The paper illustrates in details the changes in orientation and magnitude of all three principal stresses around the longwall face and T-junction area as panel orientation changes.

Jan 1, 2006

By Brent A. Elliott, J. Richard Kyle

Texas is a major producer of industrial mineral resources required by the state’s ever-growing population that now exceeds 28 million. Texas typically ranks in the top three states for the value of non-fuel mineral production with a total value of $5.2 billion in 2017, accounting for 6.9% of the total US mineral value. Almost 90% of current Texas industrial mineral value comes from the production of cement, crushed stone, industrial sand, and construction sand and gravel. Construction material consumption is focused in the 25 metropolitan areas of the state with populations of > 100,000 residents. Industrial mineral consumption is dominated by the four most populous regions of the state—Houston, Dallas-Fort Worth, San Antonio-New Braunfels, and Austin-Round Rock—with an aggregate population of more than 18 million. More than 11,000 employees work in Texas mining and processing operations. Texas produces more crushed stone than any other state from more than 200 quarries; a similar number of operations produce sand and gravel. Specialty industrial sand production for use as proppants in hydraulic fracturing for enhanced petroleum production serves as an excellent example of how developments in one industry sector can markedly affect another industry; the production of industrial sand in Texas has markedly increased over the past decade, reaching $1.3 billion in 2014. With Texas’ population projected to reach 50 million by 2050, continuing in-state development and production of industrial minerals will be required to supply its residential, commercial, and industrial users. Favorable geology and economic factors provide opportunities for identification and development of new industrial mineral production sites.