Search Documents

By G. T. Lineberry

Underground mine development begins with the positive investment decision to mine and ends with the inception of full-scale exploitation. It incorporates all activities, personnel, and equipment required for creation of underground access to a mineral deposit. Because of the depletion of near-surface mineral resources, the reduced mobility of large surface mining equipment, increasingly stringent environmental constraints, and the introduction of promising innovations to rock penetration and rock excavating equipment (e.g., continuous miners, rock borers), under-ground mining is projected to account for an increased share of worldwide mineral production in the foreseeable future. Without proper engineering during the mine development phase, failure of the underground mining project is axiomatic. A frustration attendant to coverage of the complex area of underground mine development lies not only with the need for treatment of the many disparate specialties within the area but even with the lack of systematization of these specialties in what is recognized as a vital precursor to successful mining. Section17 offers insights into (1) the basic principles of the planning and design process, including baseline assessment, reserve determination, premine planning, and subsystem design (Chapter17.1); (2) equipment selection and sizing, with emphasis on exca-

Jan 1, 2008

By Faruk Oksuz, Cary Hirner, William A. Rochford

Grouting is a frequently utilized remedy in the planning and implementation of ground improvement and tunnel rehabilitation practice. The state-of-art grouting application used for Chicago’s McCook Reservoir project offers a unique alternative to the tunneling industry for pre-excavation grouting as well as tunnel rehabilitation, rescue and post-excavation ground improvements. The McCook Reservoir project included a computerized grouting control and data collection system for a precise and highly effective groundwater cutoff in fractured dolomites. By using balanced and stabilized grout mixes, the effective permeability of the rock mass was reduced over two orders of magnitude to less than 0.1 Lugeon by installing a double line grout curtain. The stable grout mix designs allowed high pressure and effective grouting at depths up to 125 m (410 ft).

Jan 1, 2005

By Cory G. Rice

A significant portion of the piling industry has long felt relying on soil setup to gain the required capacity is a complexity that would rather not be dealt with. Instead, the pile are driven to the required capacity on the initial drive and the potential gain of capacity due to soil setup is simply considered an added bonus or safety factor. There appears to be an attitude that if one did not put in the energy required to develop the full capacity on the initial drive, then one should not expect to gain anything from Mother Nature for free. However, substantial savings in time and materials can be realized by properly accounting for setup. This paper will show the impacts and ramifications this rationale can have on required labor and material costs and illustrate a case history with significant soil setup and the savings realized on a project currently being constructed.

Jan 1, 1992

By K. G. Wang, M. E. Glicksman, P. Crawford

"We formulate the mathematical solution to late-stage multi particle diffusion in finite systems. The transition from finite system behavior to that for an infinite system is established. Large-scale simulations are reported regarding the dynamics of phase coarsening. Even in the case of a small volume fraction (Vv = 10-4), the particle size distribution is broader than that for the well-known Lifshitz-Slyozov limit at zero volume fraction. We also report the first simulation studies of extremely low volume fraction, for which corresponding experiments, as well as other simulations, do not exist at present for comparison. However, in the case of moderate volume fractions (Vv = 0.1), the fiucutations in the volumetric growth rate of particles are extracted from our simulations. These simulations provide additional insight into the statistical nature of diffusion interactions, including multiparticle stochastics during microstructural evolution.IntroductionPredicting microstructure evolution in alloys remains one of the cornerstones of materials science. Phase coarsening is a common process in microstrucural evolution that leads to a decrease in the excess total interfacial energy of the system. The system typically consists of separate and identifiable units, or domains, such as second-phase particles distributed in a matrix. During phase coarsening, larger particles grow at the expense of small particles. Over time, this ""competition"" results in an increase in the average size of the particle population, and in a concomitant decrease in the number of particles.Particle size and microstructure of many cast alloys depend on similar coarsening processes. Indeed, properties of these materials, such as strength, toughness, ductility, and electrical conductivity, depend on the material's average particle size and particle size distribution (PSD). Understanding and controlling microstructures in two-phase systems are clearly of widespread technological importance."

Jan 1, 2001

By C Simpson, J Market

The process of sampling blasthole cones utilising personnel to manually shovel material into sample bags is a long-standing industry accepted process. However, this method has several drawbacks, including the safety issues around having personnel performing manual sampling in a harsh environment and the variability involved in getting a human to repeatedly get a ‘shovel full of dirt’, and make it always representative. Geophysical blasthole sampling, or utilising a Downhole Assaying Tool (DHAT) has been tested and has now begun implementation at many iron ore sites throughout the Pilbara region, Western Australia. This method uses a geophysical tool to capture data within blastholes, and together with a semi-autonomous logging platform to minimise risks around manual handling, delivers a multielement proxy-assay which can be utilised by the mine geology team to accurately domain the orebodies. Logistically, the combination of a specially designed tool and semi-autonomous truck are the way forward for a safer and more data-robust blasthole sampling practice. The method utilises a neutrongenerating geophysical tool and linked elemental spectroscopy sensor, which measures the response of the material surrounding an open hole. This delivers results at submetre intervals. These results are then utilised, similar to blasthole sample results, to map out areas within the blast pattern that are ‘ore’, ‘waste’, or ‘other suitable grade’. This paper outlines a project that has been in ‘proof of concept’ at selected Fortescue sites over the last few years with testing of these tools carried out on reverse circulation (RC), diamond drill and blastholes. The method is now being implemented at operational hematite mine sites. Fundamentally, the method adds more than enough value to justify its implementation. The aim is that these learnings will enable the greater industry to adapt, implement and improve their mining practices. Ultimately, the outcome will be greater value in mining for the industry by having a larger volume of good quality data to make reliable decisions on material movements, minimising ore-loss and dilution, and maximising the value of our current and future orebodies.

Nov 8, 2021

By R. A. Jankowski, J. D. Potts

Four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner section averaged 0.59 and 0.26 mg/m3, respectively. The stageloader/crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feederbreaker contributed 0 to 0.2 mg/m3 of dust. A 1000 ft (305 m) increase in belt entry length or a 200 to 500 tons/shift (181,000 to 454,000 kg/shift) increase in production resulted in roughly a 0.1 mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

By Paul Hatmaker

Lime was a highly useful commodity thousands of years before the simple chemistry of its manufacturing process was known. The employment of lime for agriculture, building, and even certain essentially chemical purposes is so old that its origin is among the unrecorded details of man's first ventures into the manufacture and use of prepared substances. Lime is a most versatile material and consequently has come to be widely utilized in modern civilization. Immediately before the depression of the early 1930's the annual production of lime in the United States was more than 4 million tons, valued at 33 to 42 mil-million dollars. This output was sold to many industries, so many that mere enumeration becomes tedious.

Jan 1, 1934

By T. T. Ni

FOR MORE THAN 200 years, the Kochiu district of Yunnan province has been, and it still is, the hub of China's tin industry. The district produces annually from 80 to 90 per cent of that country's out-put of tin, which averages about 9,300 tons a year and places China fifth among the tin producing nations of the world. The tin ore reserves of the country are estimated (1) at 1,873,370 metric tons, of which 1,500,000 tons are in the Kochiu district. The mill of the Yunnan Consolidated Tin Corporation, described in this paper, is the only one of its kind in China. MINING AND SMELTING There are only two tin mines in the Kochiu district operating with modern equipment -the Hsin-Chang and the Lao-Chang, both owned by the Yunnan Consolidated Tin Corporation, a government company. The Hsin-Chang mine has four working levels with cross-cuts 6 ft. by 6 ft. and is equipped with steel mine cars and trucks to haul the ore. The ore is hoisted to surface in a three-compartment shaft and transferred to the mill by a 4-kilometer aerial tram. The Lao-Chang mine has two circular shafts 656 feet apart, each equipped with two cages. Haulage-ways 1,600 meters and 1,000 meters long, respectively, have been driven to the southwest from these shafts and are connected by three cross-cuts.

Jan 1, 1951

By I. Jauhari, F. Stober, D. Fowler, B. O. Wasmund, T. Miraza, C. Nichols, A. Taofik Hidyat, K. Said

The existing PT Aneka Tambang (Antam) ferronickel smelter located at Pomalaa, Indonesia consists of two RKEF lines with reduction furnaces nominally rated at 17 MW and 18 MW, respectively. The low power densities and heat fluxes allowed both furnaces to operate with falling water film shell cooling systems. The furnace campaigns comprised a 5-yearly cold shut -down for metal taphole area rebuild and a 10-yearlysidewall and hearth perimeter repair. Towards the end of these campaigns the furnaces would typically be operated at below nominal power due to excessive sidewall temperatures. In January 2001 Hatch performed a smelter study which proposed options which indicated the possibility of a single furnace operation for the smelter, elimination of lime addition and transition to shielded-arc operation with associated efficiency and throughput gains. This paper discusses the process of uprating the second?line furnace capability from 18 MW to 32MW following the decision by Antam to implement the recommendations proposed by Hatch. It will cover the development of scaled-up furnace design basis by Hatch and Antam with the enabling application of Hatch cooling and binding technology. To optimise the capital cost and maximise Indonesian supply content and post installation support, the scope was carefully and clearly divided between Hatch and Antam. The challenges, set backs and valuable learning experiences gained during the implementation of the retrofit include; ?The support and re-use of existing roof system and challenges presented in re-use of existing crucible support steel. ?Training and technical assistance for Antam operators to perform refractory and copper cooler installation and maintenance of crucible integrity technologies. ?Hearth integrity during start-up and development of an initial charge and start-up procedure to achieve planned thermal expansion of the hearth prior to bath formation ?Implementation of a sidewall hold-down system within the refractory sidewall due to space constraints ?Existing furnace foundation reinforcement to overcome lateral forces on furnace piers during crucible support steel expansion ?Conversion of an open-loop gravity feed cooling water system to a closed loop pressurised system with integrated emergency gravity feed and backup system ?Existing water treatment system and pumping system improvement and modification to meet copper cooling system requirements ?Integration of the new instrumentation control system designed by Hatch to increase performance of the furnace monitoring system and operation ?Uprate transformer capacity from 25 MVA to 40 MVA to meet with requirement of Shielded- Arc Furnace Operation.

Jan 1, 2007

By Jaidev Sankar

The dream of constructing the new Second Avenue Subway in New York has finally become reality as the first construction contract package is currently underway. This first contract requires the construction a TBM Launch Box in the middle of Second Avenue from which a Tunnel Boring Machine (TBM) will bore two tunnels south to 63rd Street. This paper will discuss the design of this contract and how construction has progressed including preparation, site constraints, utility construction and com-munity impacts while highlighting the challenges of working in an urban environment. It will also discuss moving forward on this major project outlining the remaining contract packages including their scope and status.

By Jr. Brinkley

For a theoretical description of power plants that derive their energy from the combustion of a fuel, it is necessary to solve, to an appropriate degree of precision, a hydrodynamic problem that requires for its solution a knowledge of the thermodynamic properties of the working fluid com-posed of the products of the combustion reaction. It is usually a good approximation to assume that the properties of the combustion gas are determined by the conditions of thermal equilibrium, and it is thus possible to employ the methods of Classical thermodynamics for their computation. The thermodynamic properties of fuel gases also are of considerable importance, as they form the basis for the design of appropriate means for their effective utilization. The specification of the operating conditions to produce a gas for use as an intermediate in a chemical process, such as the synthesis of liquid fuels, may be based upon a study of the variation of the composition of the synthesis gas with changes in the various process variables. Although there exists a large number of important scientific and technical applications of the data that can be obtained from the systematic determination of the thermodynamic properties of combustion gases, such application has been greatly handicapped by the extremely tedious and time-consuming computational methods required. The development of large-scale automatic computational equipment makes feasible the initiation of a systematic program for the determination of the thermodynamic properties of combustion gases and for the application of such data to specific problems of scientific and technical importance. As a part of its program of basic research in flame and combustion phenomena, the Explosives and Physical Sciences Division of the Bureau of Mines is engaged in such a program. The present communication is designed to introduce a series of reports presenting the results of this program.

Jan 1, 1951

By Bruce F. Grant

"INTRODUCTION The future of oil production in the part of the Appalachian region included in southwestern Pennsylvania; West Virginia, and southeastern Ohio is directly dependent on the maintenance of existing wells. This report presents an analytical study of the methods used in oil-well reconditioning in this area. The study is part of a research program designed to evaluate those means of stimulating oil production that can effectively and economically maintain present oil-production rates and make it possible to keep existing wells in operation. Well-reconditioning work was curtailed during the war; therefore, an abnormally large number of wells in the Appalachian Region is now in need of repair. Because the lubricant content of Appalachian crude: oils is high and the refined lubricating oils an; particularly suited to use in high speed, high-temperature engines, the demand for these crude oils during the war exceeds, the maximum rate of production obtainable under wartime operating conditions. Increases in operating, expenses, inability to meet war-time reconditioning costs, and inflexible price structures caused the abandonment of an alarming number of wells during the past 4 or 5 years.As a means of increasing regional oil-production rates, new drilling in the older fields for primary production generally is uneconomical because reservoir pressures in most of the fields have virtually been depleted and the production rates of newly drilled wells are small."

Feb 1, 1948

Minerals are vital to any industrialized civilization. Annually, the United States uses more than 4 billion tons of new mineral materials, or about 40,000 pounds per person-about half being mineral fuels and the other half being metals and nonmetallics. Stable and economic domestic mining, mineral, metal, and mineral reclamation industries are essential to the economy. The value of United States energy and processed materials of mineral origin exceeds $200 billion annually. Although a number of minerals are imported, especially some designated as "strategic and critical," most U.S. mineral supplies are derived from the domestic mines and processing facilities that you will be seeing, reading about, and visiting as you use this visitor guide. We hope you enjoy your experiences. This pamphlet, a guide to mining and mineral operations that may be observed or visited and some other points of interest relating to minerals, is intended to aid tourists and students who are interested in mining. Some may wish to study our Nation's romantic past; others may plan to enter the minerals industry as a career; still others may have a primary interest in conservation practices. The pamphlet is also intended to aid State and local officials, Chambers of Commerce, and mining firms in answering some of the many questions of tourists and students.

Jan 1, 1977

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster's New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process, or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, "Why automate?" Automation, automatic control devices, and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with the minimum amount of instruments needed merely to guide operators. Processes were manually con- trolled by the operator on the basis of simple temperature, pressure, flow, and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material throughput, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins, or producing a new and salable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure and (2) units which both measure and control a process variable.

Jan 1, 1979

By E. J. Gleim

In the mining of coal the trend is toward more and more mechanization. This increased use of machinery to replace hand labor is assuming many new forms and presents a constantly changing aspect. Safety engineers must be alert if the many electrical problems resulting from these new installations are to be handled safely. Some of these problems present possible electrical hazards that may be overlooked by the safety engineer unless they are called to his attention by one who has made a special study of the conditions. The foregoing is especially true of conveyor systems of mining. The terms "conveyor systems" and "conveyor mining" as used in this paper refer to those systems in which various types of conveyors are employed to transport coal away from the working place. In some mines this means complete elimination of track, cars, and locomotives. In others it means that conveyors take the coal from the working place to a convenient loading point, from which transportation is completed by cars and locomotives.

Jan 1, 1941

By Paul J. Guay

This report presents the results of evaluating a longwall mining system specifically designed to extract a very deep web (60 inches or deeper) from a longwall panel. The report includes a productivity and cost analysis comparing the new mining sys-tem with a high capacity conventional longwall operation taking a 30-inch wide web. The analysis shows the new system will increase annual production 44 percent and decrease cost per ton off the face 21 percent. The report also includes conceptual drawings and specifications for a high capacity four-drum shearer and a unique shield type of roof support specifically designed for very wide web operation. The advantages and problems associated with wide web mining are discussed in general and as they relate specifically to the equipment selected for the new mining system. The study concludes by recommending that surface coal loading tests be conducted as the follow-on work.

Jan 1, 1978

During the course of the major research in the Metallurgy Department of the University of Melbourne into the creep characteristics of lead and .its dilute alloys, it has been the practice to prepare the majority of test specimens from rolled strip. From time to time during the progress of the work, certain variables involved in. the rolling of the experimental ingots have been investigated. It is proposed to collect together in this paper the results of these experiments. Some general features relating to the type of deformation produced have been discussed in a previous paper.While it is admitted that the conditions prevailing through this work differ' in some respects from those of industrial rolling practice, it is felt that many of the factors investigated have an important practical significance. Some of the work described forms a continuation of the researches of R. S. Russell (2) , (3) , (4), into the recrystallization of various pure leads after deformation by rolling.MATERIALS USEDIn this work, a variety of "pure" leads and certain dilute alloys made from the purest of the basis leads have been studied. The compositions of the basis leads and the corres...

Jan 1, 1940

By Colin Barratt

The East Side Access (ESA) project is the largest underground rail infrastructure project under construction in New York City, USA. The Manhattan segment of the project is to be mined through rock and consists of 4.1 miles of Tunnel Boring Machine tunnels for track work and mined excavations to house rail switches, air plenums, and other rail facilities. This paper considers different methods for concrete lining, such as the use of fixed forms, adjustable forms, and pneumatically applied shotcrete. The advantages and disadvantages of these methods are discussed and the basis for considering one over the other are illustrated. Further discussions on design development and preparation of documents to facilitate quality and constructability in the field are presented.

By Thomas A. Milne

As part of the broad program to improve the safety of underground coal mines, the Pittsburgh Mining and Safety Research Center sponsored several detailed studies on the inhibition of coal dust-air explosions. The present study was one of these. The goal of the research was to advance the development of improved coal-dust explosion inhibiting agents by determining, on a laboratory scale, the basic chemical processes involved in the inhibition of coal-dust flames by dry-powder agents. B. Our Approach Neither the basic molecular processes involved in coal combustion, nor the molecular mode of action of dry-powder agents, are known with certainty. Our approach, therefore, involved the direct determination, by sampling techniques, of species behavior in small, aerodynamically simple flames. To further aid in separating behavior of coal and dry-powder inhibitors, the latter were studied in CH4-air flames.

Jan 1, 1976

By William M. Thornton

[Owing to the comparatively high freezing point of nitroglycerin (14, 15, 16, 17, 18, 23, 37, 38)3/ - 1.9° C. and 13.0° C. for the labile and stabile modifications, respectively, as determined by Hibbert (16) - manufacturers of dynamites have incorporated into the liquid portion of these composite explosives various substances capable of participating in an explosion, to depress the above-mentioned freezing point. Aromatic nitro-compounds, chiefly nitrobenzenes, nitrotoluenes, and nitronaphthalenes, have been used to a considerable extent (11), but such nitrosubstitution products have not proved altogether satisfactory, as has been shown clearly by Naoúm. (14). Consequently there has been a strong tendency in recent years to replace them with one or more of several nitric esters, among which the following (29, 35) have been prominent: Dinitrochlorhydrin (monochlorhydrin dinitrate); nitrosugars, for example, sucrose octanitrate (19); tetranitrodiglycerin (diglycerin tetranitrate); nitroglycol (ethyleneglycol dinitrate); and diethyleneglycol dinitrate (13, 46, 47). Of these, nitroglycol (33, 4l, 45, 48, 49, 65) is outstanding in importance. As the Bureau of fines is naturally interested in the analytical chemistry of the "explosive oils," it seemed desirable to bring together in this report the widely scattered experimental work covering the problem of differentiation that has appeared in various chemical and physicochemical publications.]

Jan 1, 1941