Search Documents

By Mark Rybak

On August, 31, 2006, Tropical Storm Ernesto hit the City of Richmond, Virginia. The Battery Park area was hit particularly hard, as flooding forced an evacuation of the area. A large sinkhole collapsed a sewer line in the Battery Park area, blocking the pipe and causing more serious flooding. This case history describes the fast track design, bidding, and construction of an emergency tunnel to bypass the collapsed sewer. Innovative value engineering, tunneling and shaft sinking methods, and final lining design all contributed to the success of this project. The storm inundated Richmond, Virginia with up to twelve inches of rain in some areas causing widespread flooding and damage. One of the hardest hit areas of Richmond was Battery Park. A major trunk sewer in the Battery Park area collapsed causing local combined sewer and storm-water flooding. The collapsed sewer was an 8'-3" wide by 9'-6" high arch sewer that was constructed in the nineteen twenties and later filled over with municipal solid waste and a soil fill cap to current elevations. A sinkhole was created in the area of collapse approximately sixty feet deep and one hundred feet in diameter causing the existing arch sewer to become blocked. As a result of this blockage contaminated flood waters reached depths in low lying areas in excess of twenty five feet. [ ]

Jan 1, 2008

By D. Craig Camp

conditions. The soils included 65 m of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2, 130 meters of soft clay, silt, and sand not exceeding 30standard penetration test SPT blows per 300 mm, and 220 m of rock ranging between an UCS of 400-600 kgf/cm2. The river crossing, utilizing 1778 mm OD x 19 mm wall x600 mm steel casing pipe without intermediate jacking stations, was part of a seven kilometer liquefied natural gas (LNG) transmission line in South Korea. This 440-m, 1,442-ft, river crossing was microtunneled through three different ground conditions and completed in just over three months. The crossing was achieved with an average of 25 m of ground cover and 15 m of water cover. The Kwang Yang River Crossing was part of a 7 km liquefied natural gas pipeline project for POSCO, a Korean steel producer. The microtunneling machine was custom built for this project. The microtunneling machine selected for this project was tooled with 7 button bits and 2 roller bits. None of the cutter bits were replaced during the drive. Inside the machine, before the spoils laden slurry was pump back to the surface, it would pass through an independent cone crusher. The crusher is placed in the slurry flow to make sure that none of the spoils are so large as to stop the return flow of the slurry. An additional requirement was for the inclusion of a compressed air lock. The air lock was required in the event that the cutter tools required replacement. The cutters were back loaded so that the workers would have access to change the cutters in the event of cutter failure or wear out. No intermediate jacking stations were installed for the drive. The soils included 65 meters of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2 with production averaging between 7 and 20 mm/minute. The second zone contained 130 meters of soft clay, silt, and sand not exceeding 30 standard penetration test (SPT) blows per 300 mm with production averaging between 80 and 180 mm/minute. The third zone contained 220 m of rock ranging between an UCS of 400-600 kgf/cm2 with production averaging between 7 and20 mm/minute. The steel casing pipe was 1778 mm OD x 19 mm wall x 6000 mm long. The project profile, see Figure 1, shows the soil conditions. The hand written numbers locate just above the pipeline are the production dates. The circled numbers are the 10 pipe joint increments. The project required 74 pieces of pipe to span the440 m drive. Figure 2 and Figure 3 are the jacking information. Figure 3 is a continuation of the information from Figure 2. The top section of the graph is the jacking force. The jacking

Jan 1, 2001

By David A. Newman

Barrier pillars created during mine development provide additional reserves during mine closure and can be the sole access to reserves previously abandoned because of mining height or out of seam dilution limitations. The safe and successful mining of barrier pillars requires a thorough knowledge of the magnitude and distribution of the vertical stress field in addition to the strength and physical properties of the coal, immediate roof, and immediate floor strata. Quantifying the vertical stress field is complicated by the combination of the overburden stress, abutment stresses transferred onto the barrier pillar from adjacent gob areas, and in multiple seam mining, stresses transferred from abandoned subjacent mines. These variables make the extraction and development of barrier pillar reserves a site specific consideration. Three case histories are presented in which barrier pillar development and extraction provides; i) an access point and the means to ventilate a large area of low seam reserves left by a prior operator after developing only the thicker areas of a multiple split reserve, ii) the means to increase total recovery of a deep, thick seam longwall reserve, and iii) opportunities for the development and retreat mining of a two mile long barrier pillar in thick seam reserves.

Jan 1, 1995

By Chris Jobes, Alan Mayton, N. Kumar Kittusamy, Dean Ambrose

NIOSH researchers conducted a study to compare seat designs on underground coal mine haulage vehicles. The objective of the study was to support prior findings that NIOSH-designed seats, which incorporated ergonomic design features (e.g., viscoelastic foam padding and low-back support), are improved designs. Based on measured levels of vehicle jarring/jolting and perceived discomfort, researchers evaluated four different designs - two in-use and two NIOSH-developed, ergonomic designs. Researchers collected data using a short questionnaire, a linear, visual analog scale, and accelerometers with a data recorder. Results showed that vehicle operators favored the NIOSH seats with added adjustability, low-back support, and improved seat padding over the existing seats. In addition, the measurements indicated all NIOSH seats performed better than the existing seat, under the no-load (worse of two) conditions, in reducing peak acceleration, crest factor, and RMS acceleration. The authors summarize the data collected and operator preferences for seat designs and different foam padding arrangements.

By E. M. Shemang, C. E. Suh, L. Mbinkar, University of Yaounde

"Two iron deposits within the Precambrian mineral belt of Cameroon are described in detail for the first time: the Archean Metzimevin replacement iron deposit enclosed in Fe-enriched itabirite, and the Proterozoic granite-hosted, shear zone-related Mayo Binka magnetite deposit. In the Metzimevin de¬posit, quartz is corroded and microplaty hematite overprints martite-textured hematite. The Mayo Binka massive magnetite veins show evidence of deformation in magnetite (fracturing and microbrecciation) and in overgrowths of specular hematite (mechanical twinning and undulating extinction). The magnetite is partially replaced by hematite (martitization) and goethite. Ores from both deposits have >88% total Fe2O3 and low contents of contaminants such as SiO2, Al2O3, MgO, CaO, P2O5, and TiO2. They are also poor in Cu, Pb, Zn, V, Cr, and Ni. The Metzimevin massive hematite is characterized by an accentuated light rare earth element depletion relative to the Fe-enriched itabirite. It is suggested that the Metzimevin iron deposit is the result of hypogene leaching of gangue minerals from, and further hematitization of, an itabirite protore. Although the genesis of the Mayo Binka massive magnetite is unclear, it is spatially related to Neoproterozoic granitic rocks. The data allow some comparison of these little known, but pot¬entially economic iron deposits, with some of the world’s better investigated deposits, and are useful to the exploration efforts for iron ore currently underway in Cameroon and the Central African subregion.Deux gisements de fer de la ceinture minérale Précambrienne du Cameroun sont ici décrits en détail pour la première fois : le gisement de fer Archéen de Metzimevin formé par remplacement et encaissé par des itabirites enrichies en Fe, et le gisement de magnétite Protérozoïque de Mayo Binka as¬socié au cisaillement dans un granite. Au gisement de Metzimevin, le quartz est corrodé et de l’hématite en microplaquettes se développe au dépends de l’hématite a texture martitique. Les veines de magné¬tite massive de Mayo Binka présentent des évidences de déformation dans la magnétite (fracturation et microbréchification) et dans les surcroissances d’hématite spéculaire (Macles tectoniques et extinction ondulante). La magnétite est partiellement remplacée par l’hématite (martitisation) et par la goethite. Le minerai des deux gisements contient >88% de Fe2O3 total et un faible contenu en contaminants tels que SiO2, Al2O3, MgO, CaO, P2O5, et TiO2. Il est également pauvre en Cu, en Pb, en Zn, en V, en Cr et en Ni. L’hématite massive de Metzimevin est caractérisée par un appauvrissement relatif en terres rares légères relativement à l’itabirite enrichie en Fe. Il est suggéré que le gisement de fer de Metzimevin résulte du les¬sivage hypogène des minéraux de la gangue ainsi que de l’hématitisation poussée d’une préconcentration de fer dans l’itabirite. Bien que la genèse de la magnétite massive de Mayo Binka demeure obscure, elle est spatialement associée aux roches granitiques Néoprotérozoiques. Ces données permettent de comparer ces gisements de fer peu connus et potentiellement économiques avec certains des gisements mondiale¬ment mieux connus, aidant ainsi les efforts d’exploration présentement en cours en Afrique de l’ouest et au Cameroun."

Jan 1, 2008

By S. C. Langvik

The presentation named 'Dewatering of fines by Rotary Vacuum Disc Filters' has an opening why the filtration process is important to the Iron Ore Industry. It goes on to describe the various types of dewatering machines which have been used in this industry in the last 30-40 years, and where the vacuum disc filters now dominates. It presents also the most important design changes which have been made during this period to enhance performance. Further are discussed the principles of filtration and the factors and parameters which influence performance and operating costs. As a closing is presented today's ideas and thoughts about what can be foreseen of design modifications and improvements in disc filter design in the coming ten years.

Jan 1, 2001

Silver is one of the three major metals produced from the Broken Hill mines. The accurate determination of the silver in these ores, therefore, is of economic importance.With due appreciation of the divergence of opinion of many who are interested in the subject of the determination of silver, the writer has been prompted to present the results of some recent experiments on silver losses during cupellation and conclusions from these experiments in the present paper. The losses of silver in the fire assay for this metal are due to silver retained in the slag during the fusion or scorification of the ore, and to silver volatilized from, and absorbed by the cupel during the process of cupellation.The literature describing the results of experimental work on silver losses due to the above causes is extensive, and the general conclusion of these experiments is that the silver lost in the slag is small, but that lost by cupellation is larger and more variable.The term cupellation loss in this paper refers to the total cupellation loss, no distinction being made between the absorption and volatilization losses.Volatilization loss is shown by King to be 0.5% of the total cupellation loss and, as it is generally accepted among assayers as being only a small fraction of the cupellation loss (3) (5), it will not receive further consideration in this paper.The factors causing the loss of silver by cupellation and the precautions to be obs~rved to reduce the loss in this operation are described in (1), (2), (3), (4) and (5). The...

Jan 1, 1940

By Thomas M. Barczak

The intent of this paper is to make mine operators and engineers aware of parameters which affect the loading behavior of passive roof support systems. The strength of a passive roof support element alone is not a meaningful measure of support performance. Passive roof support elements and the surrounding strata act as a system, responding to changes in the physical mine environment due to the extraction of coal and associated redistribution of stresses. The load- ing of a passive roof support element is a function of the stiffness of the roof support structure; a stiffer structure will react a higher load to a converging mine roof than will a more flexible structure. If the stiffness if the support structure is not properly designed, excessive loading will result due to the displacement of the mine roof, causing premature failure of the support. Ideally, the yield strength of a passive support needs to be no greater than that required to support the dead weight of the immediate mine roof, providing the post yield characteristics of the support are compatible with the irresistible convergence of the overburden strata and the support system continues to provide this resistance after reaching its yield load. Idealized design considerations for passive roof support systems in terms load-displacement characteristics discussed. The stiffness and yield characteristics of wood concrete cribbing, as determined controlled tests in the Bureau's Roof Simulator, are compared preliminary recommendations passive roof support utilization also provided.

Jan 1, 1987

By Gao Dazhao

This paper presents some research results of pile foundation performance. Measurements on the bearing behaviour and driving effects of piles have been carried out during pile testing and pile driving. It has been found that the ratio of end resistance to the ultimate load depends on the pile length, and the ratio in general is less than 40% for single piles. However for pile group, the end resistance seems to be greater than skin friction. The characteristic curves of skin friction and end re­sistance appear as interaction between soils and pile. The contribution of skin friction to the pile bearing capacity not only depends on soil properties but also on the relative position of the soil layer. The pore pressure and the lateral pressure in ground have been observed during the stage of driving piles. Based on the available data, the radius of plastic region and the coefficient of pore pressure A can be found analytically. The pore pressure time process curves which may be used for practice have been predicted by means of numerical method.

Jan 1, 1991

By Oliver Bowles

Accidental explosions in coal mines are due to various causes, but many of them can be directly attributed to coal dust; others that probably in no way depend on dust as a primary cause are propagated, greatly intensified, and made more disastrous by the presence of coal dust. The fact that coal dust in a bituminous mine will explode as a result of a fire-damp explosion has been generally accepted for many years, but the belief has also been held by many that coal dust is not in itself dangerous when unmixed with an explosive gas. Therefore, in past years little attention was given to dust in mines free from fire damp, and many disastrous explosions have resulted from lack of knowledge of the danger from coal dust. In the explosives gallery and experimental mine of the Bureau of Mines experiment station, Pittsburgh, Pa., it has been proved repeatedly and conclusively that coal dust will explode violently when no inflammable gas is present. PROPAGATION OF DUST EXPLOSIONS A coal-dust explosion is an extremely rapid burning or combustion of the coal particles. Their burning consists essentially of the combination of the hydrocarbons in the coal with the oxygen of the air, a process that generates heat and flame and produces hot gases and water vapor. These gases and vapors have a volume many times that of the original coal particles; thus they exert an outward motion and pressure which constitute the explosive wave. When fine particles of coal are suspended in the air, each particle is surrounded by the oxygen of the air, and thus is well placed to oxidize or burn rapidly whenever the temperature is high enough. If some particles are ignited from any cause they will fire others, and the combustion will extend from particle to particle with extreme rapidity wherever enough coal dust of sufficient purity is present.

Jan 1, 1925

By McDonald G. G

In the deformation of a metal or a single-phase alloy all the crystals composing the metal after their shape in a similar manner as the metal in bulk and to about· the same extent. This is not the case in an alloy consisting of two phases of different resistance to plastic deformation. In such an alloy the two phases take part in the deformation approximately in inverse proportion to their hardness, at least at the beginning of the deformation. (1) The hardness difference becomes less in the course of the deformation and thereby the deformation more equal. The phenomena occurring during cold-rolling of some two-phase alloys have been investigated by H. Unckel who made statistical grain measurements of the degree of deformation of the two phases after various reductions by rolling and also microscopical observations of the flow in the neighbourhood of the grain boundaries. Because of the different relative flow of the two phases, the normal flow is disturbed in the vicinity of their boundaries, and some additional plastic flow must take place in these regions, the disturbance being levelled out at some distance from the boundary. The deformation of the two phases present simultaneously in the material should thus be different from that of each phase separately. The investigation of theimportance and the effects of this interaction of crystals of different phases is the subject of this paper.The deformation of crystals occurs as a gliding of crystal layers following crystallographic laws. In consequence of this slip the crystals composing the material tend to assume a common orientation, i.e. some crystallographic axes tend to become parallel to each other in all the crystals. The type of this preferred orientation depends on the type of the crystal and the working process. Any change in the mechanism of deformation results, therefore, in a change in the preferred orientation. Such a change in kind and degree of preferred orientation will, therefore, also occur if the interaction of crystals in a two-phase alloy gives rise to a mechanism of deformation different from that in the free phases.The present paper describes a study of the preferred orientation, the microstructure and hardness in wires of brass drawn to various extents.The development of preferred orientations in the two phases with increasing reduction was followed up in various layers of the wire.EXPERIMENTAL DETAILSThe experiments were carried out with a commercial 5 S.W.G. wire (0,212 in. diameter) containing: 62·7% Cu, 37·3% Zn, very faint traces...

Jan 1, 1941

The Wamum and Idzan Creeks Prospect, located 79km W of Lae, Morobe Province, Papua New Guinea (PNG) was discovered by the exploration arm of Conzinc Riotinto of Australia Pty Ltd (CRAE). The detailed surface exploration and 11 vertical holes drilled by CRAE, combined with the recent work by Highlands Gold Limited, indicate the occurrence of porphyry copper-gold mineral- isation and associated alteration. The prospect occurs within andesitic volcanics of the Middle Miocene Langimar Beds. It is bounded by NE trending faults to the NW and SE. The alteration and mineral- isation is hosted in the andesitic tuffs adjacent to high level quartz diorite and hornblende diorite stocks. A NW trend to alteration and mineralisation is obvious in Wamum and Idzan Creeks. The main alteration type is propylitic with minor zones of potassic alteration. A late sericite-quartz-kaolinite-pyrite alteration overprinted the earlier alteration and mineralisation. Copper and gold mineralisation is related to a quartz-carbonate-chalcopyr-ite-pyrite (¦ bornite) vein stockwork and biotite ¦ K-feldspar alteration. The mineralisation system at Wamum and Idzan creeks is low in total sulphides. It is considered as a high- level fracture-controlled system with limited low grade Cu-Au mineralisation.

Jan 1, 1991

By Rethel L. Hubbard

Fourteen straight-run asphalts were prepared in the laboratory from bitumens obtained from three sources: (1) native bitumen from Rozel Point, Utah, (2). bitumen extracted from Athabaska bituminous sandstone at Canada, and (3) bitumen extracted from Edna bituminous sandstone outcropping in San Luis Obispo County, to seven asphalts with penetrations ranging from 19 to 287 at 77 F. were prepared from each of the bitumens. The yields of the prepared asphalts ranged from 74.5 percent for a 27-penetration asphalt from the Athabaska bitumen to 99.5 percent for a 271-penetration asphalt from the Rozel Point bitumen.

Jan 1, 1949

By Parker JB

The Channar Iron Ore Mining Project (the Project) is a joint venture involving the Hamersley Holdings group (Hamersley) and the China Metallurgical Import and Export Corporation (CMIEC). The Project represents the first new iron ore mine development in Australia since 1971/72 and is the first major overseas mining investment by the People's Republic of China (PRC). The Channar mine is being constructed in the Pilbara region of Western Australia and will operate for more than 20 years supplying the PRC with 200 M tonne of high grade iron ore. The Project is configured to take advantage of Hamersley's existing production and support facilities. The Joint Venturers will invest A$280 million to achieve an initial production rate of 3 M tonne/yr and an additional A$120 million over the next 8 years to achieve full capacity of 10 M tonne/yr. Financing the Project to meet the requirements of both Hamersley and CMIEC, with the dependance of the Project on Hamersley's infrastructure, and in a depressed iron ore market, required an innovative financial structure to be arranged in a limited period. This paper describes both the financial structure and its implementation, and draws a number of conclusions regarding the financing of resource projects.

Jan 1, 1989

By J. W. Paul, J. N. Geyer

"GENERAL STATEMENTThe purpose of this report, which is the first of a series of three covering mines in the Fairmont district of West Virginia, is to give the result of a' study conducted in seal mines to ascertain the nature of the safeguards employed to prevent injury to the workmen from falls of roof and coal. In presenting the subject matter, consideration must necessarily be given to factors, features, and conditions such as method of mining, timber regulations and practices, supervision and natural conditions; and, for comparative purposes, a certain amount of statistical matter bearing upon the relation of fatalities and injuries to their causes, tonnage produced, men employed, days worked, and time lost.Those features and practices found to promote safe protection are summarized and suggestions made for such additional safeguards and practices as appear to give greater protection against injury from falls of roof or coal.ACKNOWLEDGMENTSThis study of falls of roof and coal in mines in Harrison County has been conducted by the U. S. Bureau of Mines in cooperation with R. M. Lambie, chief of the Mining Department of the State of West Virginia who assigned L. W. Brown, a district mine inspector, to assist in the field work and in the preparation of individual reports on each mine visited in this study. The writers acknowledge the helpful suggestions and cooperation given by these officials, the latter of whom assisted in the field work and prop red most of these sketches for the individual reports which wore submitted to the operator by the chief of the department. Thin report is a summary of the contents of the individual reports heretofore furnished the individual operator."

Aug 1, 1931

By A. Daugiala, D. Coleman

In 2014 the New York State Department of Transportation (NYSDOT) awarded a Design-Build contract to the joint venture team consisting of Skanska which is the managing partner; Kiewit Corporation and Ecco III (SKE) and HNTB as the lead design firm. The design build team employed methods to provide schedule savings and commercial benefits to the owner NYSDOT. This paper presents the design approach and construction methods used to accelerate drilled shaft installation supporting the main span foundation for the cable stayed bridge. The drilled foundation contractor Underpinning and Foundation Skanska, a division of Skanska was responsible for assisting with design, budgeting and construction of the drilled shaft foundation construction. As part of the Request for Proposal (RFP) bid process, Alternate Technical Concepts (ATC) was encouraged by the NYSDOT. The JV team proposed an ATC which involved a scaled production shaft testing method to simulate the ultimate load level, commonly referred to as the “Chicago Method” was used in the rock socket employing the Osterberg Cell (O-Cell) testing procedures. To the authors knowledge this was the first NYSDOT project where this approach was utilized on a Demonstration/Production installation to validate construction procedures and load bearing capacities. Construction procedures, challenges and solutions are discussed in detail. Upon completion of successful drilled shaft construction, concrete integrity is verified using two methods – Cross Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP). A comparison from the contractor’s perspective is provided. Finally the drilled shaft rock socket is tested to ultimate end bearing values while rock socket side shear stresses are not exceeding the service level loading. Lateral load test was also a RFP requirement; the test arrangement and performance are discussed in detail as well. The Kosciuszko Bridge location poised unique geotechnical challenges on many levels shifting towards an extreme boundary of parameters encountered in New York City Area for drilled shaft construction. The JV team and specialty drilled shaft contractor actively participating in the shaft design and construction practice coordination and working with NYSDOT yielded a successful foundation solution which provided cost and schedule savings to the project.

Jan 1, 2016

By Michael A. Anuta

This report describes the potential for utilization of satellite observations for remote sensing of mine waste disposal areas. Four study sites consisting of metal and nonmetal mining areas in different climatic and physiographic regions of contigous United States were used in this investigation. The mine waste disposal sites consisted of mining of phosphates in Florida, copper in Arizona, silver in Idaho, and coal in West Virginia. Landsat satellite multispectral scanner observations were used together with aerial photographs, ground surveys, U.S. Geological Survey maps, and other ancillary information. Landsat digital data were categorized using automated supervised classification algorithms and an image analysis system. Detailed description of automated classification techniques employed and the accuracy attained is provided together with the results of manual interpretations. The inventory of areas distrubed for phosphate mining and a change detection investigation for-Polk County Florida were also undertaken during this study.

Jan 1, 1982

Upon cessation of mining activity open-cast mine pits typically fill with water, forming a æpit-lakeÆ. The water in these lakes, in some instances, contains high concentrations of ædeleteriousÆ material. Containment and/or dilution typically requires an understanding of how stratification in the pit-lake will develop over a long timescale (say 100 years). Vastly different transport rates can develop due to differing hydrogeochemistry, basin morphology and climate. Numerical (computer) modelling is the most likely approach for successful prediction over long times. While lake modelling tools are available, useful numerical modelling requires improved understanding of transport in such systems because they are different to natural lakes in a number of ways. Notwithstanding the effort required to improve our understanding, the modelling provide a means of testing approaches to active management of pit-lakes.

Jan 1, 2002

By D. K. Bose, R. H. Rakhasia, V. D. Shah, J. C. Sehra

A series of experiments was conducted to determine the effects of roasting temperature, soaking period and quantity of soda ash added. At a laboratory scale, under optimum conditions of roasting at 873 K for 2 700 s with soda ash 10 wt% in excess of stoichiometric, molybdenum recovery was 99%. The investigations indicate the technical feasibility of producing high-purity MoO3 by combining the roasting process with carbon adsorption/desorption. The process uses low-cost chemicals, can be scaled up readily and is free of the SO2 pollution generated by conventional roasting, as the sulphur content of the concentrate is converted to sodium sulphate

Jun 18, 1905

By Peter McDonald

In 1994 the world's largest underwater tunnel was constructed to link Canada and the U.S.A. This new tunnel was large enough to accommodate double-decker railway cars. The construction of an unplanned Retrieval Shaft was required to allow removal and servicing of the Cutterhead of the Tunnel Boring Machine before it passed under the St. Clair River. This paper, which is a revision of that published in Canadian Tunnelling, has been modified here to emphasize construction considerations and describes the evolution of the design and construction of this "Rescue Shaft" under extreme schedule pressure, and changed ground conditions..

Jan 1, 1997