Search Documents

By K. Heindlhofer

Estimates of the "plasticity" of a metal are commonly deduced from three types of test—tensile, torsion and impact. The several results have been more or less at variance, though this disparity has attracted little notice, largely perhaps because they have been expressed in different terms. The discrepancy between the results of the three tests becomes obvious when each is made at a series of low temperatures, for the temperature range within which the "plasticity" of iron largely disappears proves to be very different in the three types of test. The rather abrupt disappearance of "plasticity" of iron within a narrow temperature range cannot be due to any physicochemical change (such as a precipitation) taking place in the material at that time, because the original plasticity is immediately regained when the temperature of the material is brought above the sensitive range. Accordingly this difference in behavior shows that the "plasticity" of a metal depends upon the mode of action of the stresses which produce the deformation, and therefore upon the method of test. Analysis of the stresses leads to the conclusion that the observed plasticity of a metal is determined by the relation between its resistance to rupture by separation and its resistance to shear (slip), on the one hand, and between the effective normal and shearing stresses on the other; and that the relation between the two resistances does not in general remain constant with change of temperature, and may somehow be altered to some extent by the previous treatment of the specimen. This suggests the view that the results of none of the usual mechanical tests are directly comparable even for a single metal tested at a series of temperatures, or for a series of metals at one temperature, because the proportion of the total resistance of the metal to the test contributed by the

Jan 1, 1935

By K. Heindlhofer

Estimates of the "plasticity" of a metal are commonly deduced from three types of test—tensile, torsion and impact. The several results have been more or less at variance, though this disparity has attracted little notice, largely perhaps because they have been expressed in different terms. The discrepancy between the results of the three tests becomes obvious when each is made at a series of low temperatures, for the temperature range within which the "plasticity" of iron largely disappears proves to be very different in the three types of test. The rather abrupt disappearance of "plasticity" of iron within a narrow temperature range cannot be due to any physicochemical change (such as a precipitation) taking place in the material at that time, because the original plasticity is immediately regained when the temperature of the material is brought above the sensitive range. Accordingly this difference in behavior shows that the "plasticity" of a metal depends upon the mode of action of the stresses which produce the deformation, and therefore upon the method of test. Analysis of the stresses leads to the conclusion that the observed plasticity of a metal is determined by the relation between its resistance to rupture by separation and its resistance to shear (slip), on the one hand, and between the effective normal and shearing stresses on the other; and that the relation between the two resistances does not in general remain constant with change of temperature, and may somehow be altered to some extent by the previous treatment of the specimen. This suggests the view that the results of none of the usual mechanical tests are directly comparable even for a single metal tested at a series of temperatures, or for a series of metals at one temperature, because the proportion of the total resistance of the metal to the test contributed by the

Jan 1, 1935

By Stone. Jon P.

INTRODUCTION Countries that are currently developing their mineral potential have unique information systems requirements to support these activities. The mining laws usually grant the State considerable authority over the process. In many instances, the mining laws give a government agency the responsibility for granting and controlling exploration permits and development concessions. This is the case in Costa Rica. The Direcion of Geologia, Minas, y Hidrocarburos (DGMH) of the Ministerio de Industria, Energia y Minas (MIEM) is responsible for the management and operation of the National Mining Register. This paper describes the results of two studies of the information system requirements to support the National Mining Registry as well as those supporting some of the other function of the DGMH. The first of the studies reviewed the situation before the installation of computer equipment. The second study evaluated the installed systems. BACKGROUND Historical Perspective Mining in Costa Rica is at present a relatively minor part of the economy. It consists primarily of industrial minerals and gold production. Gold production is largely by small-scale miners and may be more substantial than reported. There is considerable interest on the part of the Government in both having a better understanding of the existing mining industry and promoting future development. Mining law was first provided by the Ordinanza de Mineral (of 1830). This was replaced by the first Mining Code of 1953. Apparently, one of the first problems caused by the 1953 law was the granting of concessions which were not worked. A 1968 agreement with ALCOA also resulted in political conflict. The Government worked on a new Mining Code for many years and in 1982 the current Mining Code was enacted. Draft implementing regulations were prepared in April 1984. Mining Code of 1982 The Mining Code of 1982 addresses most aspects of mining in Costa Rica including the declaration that all mineral resources are to be the property of the State. The State may grant exploration permits and exploitation permits. The exploitation of hydrocarbons, radioactive minerals and certain water resources was reserved to the state. The DGMH was given authority to settle placer claim disputes, maintain a registry of exploration permits, and exploitation concessions. and generally supervise mining activity. Towards this, the Mining Code of 1982 includes rather detailed requirements for the processing of application for permits and concessions. Mining Code Application Requirements The following briefly describes the requirements to give the reader a feeling for the complexity of the process. Currently, over 1,000 active applications, exploration permits and exploitation concessions are being monitored under the process. The number remains relatively consistent in that the number of new applications is usually about the same as the applications that are put aside. The time and date of the filing must be certified by the DGMH. The application must include all the information specified in the Mining Code. If incomplete, DGMH must notify the applicant of the deficiencies or omissions and direct that the applicant correct the deficiencies or omissions within 8 business days (a single 30 business-day extension is allowable). If the applicant does not respond as directed, the application is deemed as not having been filed and the pertinent information is placed in the files. The DGMH must reject the application outright and direct it be placed in the files in the following cases: (a). If the new application covers the area of a previous permit or concession, either being processed or already granted.

Jan 1, 1987

By W. M. Cross

Bubble attachment time measurements for the rare-earth phosphate minerals monazite and xenotime were made as a function of oleate concentration, sodium fluoride addition, and temperature. Results indicate that the rare-earth phosphates behave similarly to other phosphate minerals, notably collophanlte and fluorapatite, which have been studied previously. The addition of sodium fluoride yielded a modest decrease in bubble attachment time with fluoride additions below the apparent fluoride surface precipitation point, while at fluoride additions greater than the apparent precipitation point a significant decrease in attachment time occurs. Increasing the temperature or the system gave a slight decrease in bubble attachment time in the absence or sodium fluoride. With sodium fluoride addition and below the apparent fluoride surface precipitation point, an increase in temperature actually increased the attachment time. For sodium fluoride additions above the apparent fluoride surface precipitation point, a temperature increase significantly decreased the attachment time.

Jan 1, 1989

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue. Thank you to the industrial minerals annual review editor, to the technical committees chair and vice-chair, and to the authors of the individual commodity profiles. Jim Norman, member SME, of GeoTrans, Inc., is the industrial minerals annual review editor. SA Ravishankar, member SME, of Cytec Industries, is chair of the industrial minerals technical committees. Technical committee vice chairs include: ? Abani Samal, member SME, of Pincock Allen & Holt, agricultural minerals. ? Aaron McMahon member SME, of Pincock, Allen & Holt, ceramics and refractories. ? Bradley S. Van Gosen, member SME, of the U.S. Geological Survey, chemical raw materials. ? Mark Zdunczyk, member SME, of Continental Placer, Inc., construction materials. ? Jerry Gauntt, member SME, of JEG Minerals Consultants, fillers and pigments. ? Michael Cheshire, member SME, of Indiana University, sorbents, filters and process aids. Their help makes possible this June industrial minerals issue. On behalf of ME readers, the editors thank them.

Jan 1, 2008

By Servant S

In the mine of this study, cemented hydraulic backfill is placed under the form of a slurry at a percentage of solid by weight varying from 50 to 65 per cent. This slurry settles and cures in the stope. During this process an important amount of water must be drained from the scope. Field observations in the case studied here show that the geometry of the drains system has a significant impact on the drainage of the stopes. The mode of filling produces a backfill showing an evident stratification typical of a sedimentation process. In situ observations on this material show that this stratification translates into a very strong heterogeneity in the physical properties of the cemented backfill. This heterogeneity should affect the hydraulic conductivity of the backfill in the scope. In order to study this aspect, finite element simulations were performed. This paper presents the results of these simulations, where the impact of this stratification on hydraulic conductivity is related to the performance of the backfill drainage system for various geometry. This preliminary study is aimed at providing a better understanding of the role of the drains in the dewatering process of the backfilled stope in the case of this Mine.

Jan 1, 1998

By Marco Barla, Mariacristina Bonini, Giovanni Barla

ABSTRACT: The paper describes the characterisation studies of Tectonised Clay Shales at laboratory and in situ scale. The interest relates to tunnelling under squeezing and swelling conditions, in Italy, along the Apennines. The results of monitoring during full face excavation are presented in conjunction with numerical modelling. RESUME: Cet article présente la caractérisation, à l'échelle du laboratoire et in situ, des Argiles Chaotiques. L'attention est portée sur le creusement, dans ces milieux gonflants, des tunnels, dans les zones montagneuses des Appennini, en Italie. Enfin, on présentera les résultats de la modélisation numérique et la comparaison de ces derniers avec les mesures effectuées in situ. KURZFASSUNG: Die Arbeit beschreibt die Charakterisierungsstudien von tektonisierten Schiefertonen, sowohl im Labor als auch vor Ort. Das Interesse gilt dem Tunnelbau unter Quetsch- und Schwellbedingungen in Italien entlang der Apenninen. Die Überwachungsergebnisse des ganzflächigen Ausbruchs werden mit numerischen Modellen präsentiert.

Jan 1, 2003

By S. G. Britton

Microcomputer analysis has long been a technique for engineering professionals to improve the theoretical and practical design of continuous mining systems. Such work has been typically composed of modeling observed events and then introducing a variety of known elements with predicted results to compare against the results of the model. Programs written in BASIC, Cobol, Fortran, or other language dominated such efforts. These programs have taken years to develop and prove out. This paper explores a new management tool used at TMC on a daily basis to track and improve continuous mining systems through the use of microcomputers and Lotus 1-2-3 software. By analyzing data provided by section foreman, shift foreman, and maintenance personnel against predetermined goals, new production targets are developed, weaknesses in the current mining systems are identified, and the results of changes are measured. The results of this system on the productive output of TMC systems are on the order of ten percent improvement.

Jan 1, 1991

By P. W. J. van Rensburg

Our mineral heritage - PRESIDENTIAL ADDRESS given by P. W. J. van Rensburg, Pr. Eng.. B.Sc. (Eng.)(Rand) INTRODUCTION Stone Age people were living in various parts of South Africa as recent,ly as a thousand years ago, when they were displaced by Iron Age people with a culture developed in the far north. These invaders brought farming, building, and the earliest mining developments to the Transvaal, thus ushering in the beginning of our great mineral heritage. It is of particular interest to record that, up to comparatively recent times, some of these people were excavating iron-bearing shale rocks for their smelting furnaces on the Melville Koppies in J ohannesburg. Although the most recent the iron-smelting furnaces discovered on these koppies is estimated to be some five-hundred years old, it believed that these Iron Age people were driven out, and their settlements destroyed, by Zulu impis only one-hundred-and-fifty years ago.

Jan 10, 1973

By Lorraine B. Burgin

This study by the Bureau of Mines documents the leadtime required for preliminary and detailed exploration, development of the mine, and construction of beneficiation and support facilities for selected copper deposits in Arizona. The time for major exploration ranged from 1 to 15 years, time for open pit development (or construction) was 1 to 4 years, and time for under- ground development was 4 to 8 years; one underground mine presently being developed may require 12 years to achieve production. Construction of the beneficiation plants required 8 months to just over 2 years. The data are supported by historical facts for each deposit during the leadtime stages from location of claims through exploration, construction, expansion, and leaching. The sequence of development and factors contributing to differences in the time spans are discussed. Histories are detailed for the Miami, Castle Dome, Copper Cities, San Manuel-Kalamazoo, and Twin Buttes properties; briefly summarized are the Pinto Valley, Miami East, Esperanza-Sierrita, Pima, and Mineral Park Properties. Each mining operation had its own pattern of development, and together they present a source of planning information for the development of other properties.

Jan 1, 1976

Provide the mining industry with a simple, accurate and readily available means of measuring the gas flow from pipe outlets such as gob holes Approach The Bureau of Mines conducted laboratory studies to establish correction or method factors for anemometers when used to measure gas flow from pipe outlets. Using the Anemometer Anemometers are used by the mining industry to make air velocity measurements in mine entries. Although the instrument has no appreciable influence on the airstream in mine entries, especially since the cross-sectional area of an entry is much larger than the cross-section of the anemometer, correction or method factors are used to correct the center line anemometer velocity to average velocity. This adjustment is made because the air velocity in a mine entry is highest in the center and lower at the sides. Anemometers can be used to measure gas flow from small diameter pipe outlets; however, since the instrument diameter is much larger than one-sixth of the pipe diameter, it will influence the air-stream from these small outlets. Resulting velocity measurements are erroneously high by as much as 30 percent. Method factors must be applied to such anemometer measurements taken at pipe outlets. Through a research investigation the Bureau of Mines established a set of method factors for center-line anemometer readings taken at the discharge end of 4-to 8-inch diameter pipes. These method factors were combined with method factors which were developed by the National Coal Board of Great Britain for 12-to 30-inch diameter pipes. The anemometer was mounted on the end of a short rod and held against the pipe for support except on the 4-inch pipe where the instrument was started and stopped remotely to prevent hand interference with the air-stream during measurements. Method factors were determined by comparing the anemometer measurements at the pipe outlet to the true average airflow which was simultaneously determined upstream by venturi measurements. Consequently, a method factor is nothing more than the ratio of the true velocity to an anemometer measurement.

Jan 1, 1987

By Ronald E. Hamilton

"An attempt to review the recent literature on comminution reveals at once that the subject has many ramifications and that the applications are so diverse that there are very few general statements which can be made.It. seems reasonable to start classification on the basis of size of material as Input to the comminution process. However, we find that this can only be done in a very imprecise manner.The initial step of breaking rock from its natural state of very large pieces in geological formations into sizes suitable for processing is accomplished by blasting. This step in the process has not been ex-amined in this project except to note that great changes have been made during the last decade or so in the explosives used, and in the method of handling them. We should determine what effect changes in mining methods can have on the need for crushing.The second step in the process is usually primary crushing, performed by gyratory or jaw crushers. The largest chunk which can be fed to a jaw crusher depends on the size of the machine, and should be larger than the largest fragment produced in the miring process. It is obvious that the larger the crusher, the less care required in mining to en¬sure the absence of rocks too large to be crushed. The optimum size of crusher to minimize overall cost of mining and reduction is not at all obvious, and no information on this point has come to light in this investigation.It is rather generally accepted that size reduction is most efficiently done in small stages, and that different machines have different opti¬mum size ranges of feed. For example, crushers are preferred for sizes above about 1"", rod mills for the range between 1"" and 0.1"", ball mills are preferred from 0.1""down to perhaps 10 microns, and vibratory mills, or jet mills, below 10 microns."

Jan 1, 1976

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By AIME AIME

T HE 133rd meeting of the A. I. M. E., opening in New York on Feb. 15, promises to be as successful technically and socially as any in the past. The papers submitted for the various technical sessions are unusually excellent and insure something of interest to every group. Tentative programs have already been issued, and a concise resume of the various sessions, arranged chronologically, appears on page 48. Among the many interesting technical sessions arranged, attention is directed to those of the Petroleum Division, embracing the Symposium on Production that has come to be an annual feature, and new ones on refining practice, transportation and economics. The Institute of Metals program is similarly comprehensive. It includes 15 papers, 8 on copper, 4 on aluminum and its alloys, and one each on magnesium, lead, and fatigue of metals. The Coal Committee offers as a leading contribution its report, prepared under the direction of H. N. Eavenson, giving a new analysis of the capacity of the mines and a comparison of coal with other industries. This will be supplemented by a number of other papers of especial interest to operating men, among which are "Data on Use of Loading Machines in Bituminous Mines," by Graham Bright; "Evaluation of Coal," by R. H. Sweetser; "Selection of Coals for the Manufacture of Coke," by H. J. Rose; and "Relation of Origin and State of Carbonization of Coal to Problems of Low Temperature Carbonization," by S. W. Parr. The Iron and Steel Committee has scheduled seven papers, and there will be a special session on open-hearth practice, in which will be presented the first results of the two conferences, held by the sub- committee at Pittsburgh and Cleveland. A symposium on molding sands will be a special feature of the session on non-metallics.

Jan 1, 1926

By Rita D. Sylvester

"THE BUREAU OF MINES was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve mineral resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with that directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau sources. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented III this special publication both necessary and valuable. This issue describes Bureau reports and articles published during the period January 1, 1960 to December 31, 1964. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960,2 and the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960.3 It supersedes the annual lists of Bureau publications and articles from January 1 to December 31, 1960/ from January 1 to December 31, 1961,5 from January 1 to December 31, 1962,6 and from January 1 to December 31, 1963,1 The leading general and technical libraries of the United States maintain files of the Bureau's publications. A list of these libraries appears immediately following this introduction. BUREAU PUBLICATIONSBecause some series of Bureau reports contain both free and sales publications, and because the cost of sales publications varies, prices are indicated in the individual listings of all publications for which charges are made."

Jan 1, 1964

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By B. P. Nutter, M. Lebourg, J. A. McAlister

The Multi-Flow Evaluator (MFE) is a new system of tools providing an original approach in drill-stem testing. It improves control during the testing operation and gives a more accurate evaluation of the fluid recovered while providing additional pressure information for reservoir analysis. The tools are operated entirely by up and down motion of the drill stem. This up and down operation provides a positive means of control and offers easily observed surface indications of tool operating position. An unlimited number of shut-in and flow periods may be taken with this tool while in the hole. The key to the success of the MFE system of tools is the safety seal packer. Until this development, operation of the tools by up and down motion only had proven unreliable. The success ratio of the MFE now exceeds the ratio achieved by conventional tools. The equipment includes a 2,750-cc chamber in which a representative sample of the flowing formation fluid is trapped at the end of the last flow period and brought to the surface under pressure. The sample can be evaluated at the wellsite or transferred under pressure for laboratory analysis. The sampling feature of the tool allows a sample to be obtained from a reservoir which has suffered minimum influence from production. A representative sample can be obtained for laboratory or empirical analysis by employing a testing technique to minimize drawdown during flow periods. Interpretation methods to take advantage of this additional information are presented and supported by actual field examples. INTRODUCTlON The Multi-Flow Evaluator (MFE) represents the most recent technical advance in formation testing. Drill-stem testing techniques prior to the MFE have been limited in three areas—(1) operaiion, (2) recovery analysis, and (3) reservoir analysis. The tools in the MFE system allow maximum control during testing and provide test information superior to that obtainable with conventional tools. The system of tools and the operation procedures are described to illustrate the mechanical advantages over present tools. Methods of pressure build-up and fluid

Jan 1, 1966

Gold mines produce unique water treatment requirements. This paper focuses on case studies of innovative processes used for treatment of water resulting from gold mining and processing. The case studies include treatment of mine dewatering water for beneficial application from an Australian gold mine, Bendigo Mining, as well as treatment for arsenic removal of tailings water from mining and processing at Goldcorp mines in Canada. Gold mining can often require dewatering to prevent groundwater seeping into and flooding the mine workings. Gold mining and processing often accumulate wastewaters in a tailings dam. The mine water can contain contaminants such as dissolved salts, iron, arsenic, manganese, heavy metals and odorous sulfates. Environmental discharge requirements as well as community needs for water drive mine operators to consider the most appropriate water treatment process. Treatment of gold mine water can require processes including oxidation, pH adjustment, coagulation, flocculation, clarification, further oxidation/adsorption of specific metals such as manganese, filtration, salt reduction utilising reverse osmosis, brine minimisation and other innovative technologies. These processes are discussed through the case studies with examination of the specific treatment process that is required. This paper uses real case studies of gold water treatment processes to explain and examine the technology and the reasons for designing specific processes. The focus is toward explaining innovative processes where the water is used for sustainable environmental discharge or treatment to a quality that can be beneficially used by the local community.

Jan 1, 2007