Search Documents

By G. E. McElroy

As one phase of a general program of enthracite mine-fire research initiated by the Bureau of Mines in September 1935, a study of the records of past fires was considered a necessary approach to a proper understanding of present and future fires because only limited information could be obtained directly from existing active fires on account of their inaccessibility. Through the courtesy of interested operators, all available records of fires that had occurred in a large group of steep-pitch anthracite mines in the Western Middle and Southern fields of the Pennsylvania anthracite district were examined and analyzed for data on the causes, costs, behavior, and control of fires, and this report is primarily a discussion of these factors based on a close study of these particular records. Mining Conditions The records pertain to a group of mines that have contributed about 12 percent of the total Pennsylvania anthracite production and constitute a large proportion of, and well represent, steep-pitch operations in this district. Throughout the area represented, the coal occurs as a series of up to 20 parallel seams in folded slate and sandstone strata and almost entirely on pitches of 400 to 80°, with vein thicknesses of 5 to 60 feet. Practically all are old mines with histories dating back to 1850, or thereabouts, and present operations are either under or adjacent to mined-out areas extending to surface or to the saddles of anticlines. All operations are at relatively shallow depths, that is, within 1,000 feet, vertically, of the surface. Mining methods are largely a heritage of the past and embrace typical breast and pillar operations with practically no mechanized mining and with the coal shot ?off the solid.? Most of the mines are rated as gassy and are operated now on a closed-light basis. Permissible explosives are now used entirely for breaking coal, and dynamites for rock work and chute-starting blasting.

Jan 1, 1938

By S. Constantinides

"A major use for many of the rare earths is in permanent magnets. While alternate technologies are in research or already exist, rare earth magnets are unlikely to be supplanted as a major input to clean technologies and high efficiency consumer and industrial devices. We’ll examine where and how the magnet rare earths are utilized and the size of the market. Market growth forecasts based on global markets will be presented. A brief explanation of materials research in the US completes the material.INTRODUCTIONRare earth magnets, first commercialized c.1969, have become essential for a wide range of consumer, industrial and military devices. They are used in the speakers and vibrator motors of cell phones. Rare earth magnets spin the hard discs within the drives and rare earth magnet voice coil motors position the read/write head over the spinning platter. Rare earth magnets are the heart of motors and generators used on airplanes – they are smaller and lighter weight than alternative materials/devices. Now rare earth permanent magnets are being introduced into electric vehicles and wind power generation.Rare earth minerals are difficult to extract from the ores and to separate from one another. The increase in use of rare earth magnets has placed a severe strain on established sources of supply. The establishment of new mines and processing facilities is costly and requires upwards of 15 years to become productive. The combination of rapid rise in use of rare earth minerals coupled with supply shortages has caused rapid price increases and threat of non-delivery of product. The result of this disruptive situation has been a profound response at several levels: corporate, industry-wide and governmental. Let’s learn more about why rare earth magnets are so important to modern society."

Jan 1, 2012

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing cloy reining, crushing, and grinding methods and costs at various operations throughout the United States. These Toners are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production casts. Although the publication of total production cants might not be advisable in sore instances, yet a knowledge of operating costs is essential to the technical discussion end study of the methods employed. The attention of the reader is specifically coiled to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The following report deals specifically with the methods employed by the Clay City Fire Co., Uhrichsville, Tuscarawas County, Ohio.

Jan 1, 1936

By C. F. Cornell, R. C. Emmett, D. A. Dahlstrom

FOR many years the disk-type and cloth-covered drum filters have found widest application in liquid-solids separation, which uses continuous filters. The disk type is less expensive, occupies less floor space per square foot of filtration area, and requires negligible down time for filter media changing. However, because filter cloth is billowed out by the blowback in the cake discharge, it is very short-lived if the scraper blades are set too close. Consequently cake weight is very important in assisting cake discharge, which normally necessitates a minimum cake thickness of 3/8 to ½ in. Also, the vertical position of the disks eliminates the possibility of efficient cake washing for removal of soluble values. The disk-type filter is generally limited, therefore, to applications that require no cake washing and form relatively thick cakes within the normal range of filter cycle times. The conventional cloth-covered drum filter is a more flexible unit, permitting wider variation in the percentage of cycle time devoted to cake formation, dewatering, or washing, as required by the application. Thinner filter cakes can be discharged because a horizontal line across the filter medium at the location of the scraper blade is equidistant from the edge of the blade at all points. The scraper blade therefore may be set a short distance from the filter medium or, where wire winding is not used, a floating scraper can be utilized so that the contour of the cloth can be followed. The drum filter is generally employed when there are difficult filtering slurries with resultant thin cakes or when cake washing to recover soluble values must be practiced. Difficulties sometimes encountered in continuous filter operation can be summarized in the following four categories: 1) Low filtration and/or washing rates due to blinding of the filter medium. 2) Poor cake discharge resulting from sticky cakes, filter medium blinding, or too thin a cake for the particular type of filter. 3) High filter media costs caused by short life and frequent down times for cloth changing. This results from blinding or from abrasion by the scraper blade when cakes are thin. 4) Blowback of filtrate at cake discharge because not enough air passes through the cake to purge the drainage area and filtrate lines during dewatering. To reduce or eliminate blinding tendencies several modifications have been tried, for example, cover-cleaning showers, blowback under the feed slurry, and snap-blow cake discharge. In many cases, however, this simply retards the rate of blinding, since the filter medium is kept clean at its outer surface only by these methods. As blinding usually occurs within or on the back of the medium, the operator is finally forced either to remove the cloth and scrub the medium intensively with a cleaning solution or acid-rinse it on the filter—all resulting in down time, short cloth life, and additional costs.

Jan 1, 1959

By E Nye and T Schroeter, B Muir, M Kitson, M Gonzalez, D Mares

The single track North Strathfield Rail Underpass (NSRU) consists of a dive structure either end of a 148 m long driven tunnel skewed under three live railway tracks. The tunnel is 8 m high, 9 m wide, with a horseshoe profile, excavated by full face using a road header. Ground cover varied between 2.5 m to 3.5 m. Settlements were 5 mm to 15 mm (the latter due to a dyke). A one pass synthetic fibre reinforced shotcrete lining was installed (no lattice girders or steel sets were used). A system of automated robotic total stations was used to provide real time monitoring of the rail track and associated ground formation. No disruption to train services occurred.CITATION:Gonzalez, M, Kitson, M, Mares, D, Muir, B, Nye, E and Schroeter, T, 2014. The North Strathfield Rail Underpass – driven tunnel design and construction, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 369–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By N. T. Avard

THE profitable disposal and utilization of much of our slack coal, lignite, and other low-grade fuels is one of the major problems facing the coal mining industry of Canada today. It is my belief that the pulverization process applied to these fuels opens the door to greater efficiency and greater prosperity, and I wish to discuss briefly with you some features of its development and advantages to date. Indeed, the art of burning pulverized coal under stationary boilers is one of the romances of modern engineering. As a Nova Scotian, I feel some pride in the fact that at Chignecto Mines, N.S., was built in 1906 the first pit-mouth power plant on the North American continent. This was built to make effective for the first time Edison's dream of carrying coal for power by wire rather than by rail. This plant, built by the Maritime Coal, Railway and Power Company, Limited, success-fully utilized underfeed stokers for twenty years but in 1927 was replaced by a more modern plant equipped with machinery for burning pulverized coal, which is now operating very successfully. A further source of pride is the fact that the first boilers on this continent to be operated by pulverized coal were installed by the Dominion Coal Company at New Waterford, N.S., in 1912 and were satisfactorily operated during the lifetime of the plant. It is an acknowledged fact that average living conditions on a large part of the North American continent are far superior to those of any other people on earth. The reason is that we use so much more machinery per capita, and cheap power supply has been a large factor in bringing that about. Statistics show that where one horse-power was used one hundred years ago to assist man in his work, five hundred horse-power is used today. Truly a remarkable development and the key to our present high standard of living. Lack of coal in the chief industrial centres of Canada has forced the extra-ordinary development of the water powers which Providence has placed in those centres. How many of us realize that Canada stands second in the world in the per capita development of hydro power, Switzerland being first and the United States sixth? From this condition, we are reminded of the fact that the per capita foreign trade of Canada far exceeds that of our great neighbour to the South-but another illustration of the benefits accruing from our great power development.

Jan 1, 1937

By Jos. R. Guiteras

This paper has been written to describe briefly the mining and milling of gold and silver ores in the Black Canyon and neighboring mining districts in Yavapai County, Ariz. The description of present operations is the result of a 10-day visit to the region by the writer in March 1936. Acknowledgments The author is indebted to earlier writers on the geology and mining in this regions and to the mine managers and their staffs, whose courteous cooperation has made possible the assembling' of material for this paper. Individual acknowledgments are made in the text.

Jan 1, 1936

By M. Onifade, O. S. Otuogbai, A. F. Mulaba-Bafubiandi, O. D. Eniowo, H. Grobler

Artisanal and small-scale miners in Nigeria struggle to attract formal financing to upgrade their operations to a more sustainable form of small-scale mining operation. Literature shows that for an investment to attract formal sources of financing; the business must be considered creditworthy by potential lenders. This means that the credit risks associated with the investment must be bearable for the potential lender. This study looks at how artisanal and small-scale miners can attract formal funding, which will help them take the leap from artisanal state to a form of sustainable small-scale mining operation. This study evaluates the creditworthiness of artisanal and small-scale mining operators using key credit risk parameters identified in the literature and through primary investigation. A quantitative study is conducted on a sample of 100 artisanal and small-scale miner establishments in Nigeria to evaluate the effect of these identified credit risk parameters on creditworthiness. It is shown in this study that being a member of a mining cooperative society, which is a form of social collateral, best improves the chances of access to formal financing for miners within the sample group. This underpins the role of social collateral, in both the formal and informal economy, and its influence in improving the creditworthiness of a typical artisanal and small-scale miner.

Jul 23, 2025

By Todd M. Ruff

Blind areas around construction equipment are a major contributing factor in incidents involving a piece of equipment striking a worker. In highway construction, these types of incidents result in an average of 22 deaths a year in the United States. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these incidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers or other objects. Several camera and sensor systems are available for this application. These systems were evaluated on various trucks used in road construction and maintenance. Tests were conducted on sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted on dump trucks and utility vehicles during the warmer months to study the effectiveness of the systems in highway work zones. Results showed that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in congested work areas.

By L. C. IlsLey

"The maintenance of permissible equipment which is tested and inspected at the Pittsburgh Experiment Station of the United States Bureau of Mines is dependent to a surprisng degree upon the voltage at which the equipment is operated. The difficulty of maintaining 500-volt equipment is frequently brought to the bureau's attention, and it is quite possible that if the bureau had appreciated at the beginning the full hazard involved, it would never have undertaken the approval of equipment operating at voltages greater than 250 volts.In this connection, the following statement from State mine inspection departments and other sources are of interest as showing the general feeling in safety organizations with respect to voltages higher than 250. These statements, although obtained as a result of a questionnaire sent cut several years ago, still apply very well to present conditions.A. I have not had time to consider seriously the proposed change from every angle, but looking at it from a standpoint of hazard, feel that the danger would be greatly increased. I have always occupied the position that underground voltage on portable equipment should never exceed 250 volts.High voltage of course would mean smaller transmission lines, which would be more economical and no doubt would require in several instances smaller equipment; notwithstanding, if this statement is true, the writer is still favorable to low voltage on underground portable equipment.B. I believe 500 volts should be the limit on the best equipment ender the best conditions and that the U. S. Bureau of Mines should do all in its power to limit the voltage to 500 volts on permissible equipment, as any increase in voltage means increased hazard.C. I will refer you to a section of our mining law, entitled ""An Act to Regulate the Tine of Electricity in the Mines of the State of ----"" which reads in part, as follows: Trolley wires, or other exposed electrical wires, shall not carry a voltage above 275 volts.You may readily see by this that we are not permitted to operate mining machines under ground in -----, with more than 275 volts at the terminals, except that we are permitted to install transforming stations throughout the mines, after complying with certain regulations at the mine.However, as we have had to date, within the calendar year of 1925, six men electrocuted in the mines of the State, using a voltage of 275 volts, I am of the opinion that if this voltage was increased, the hazard would also be increased in proportion.D. I do not care to make a statement for publication: however, I am referring you to our mining laws. On page 27 and 28 you will find what the laws of -----¬require relative to the installation of electricity in the mines.""Hereafter where electricity is installed no higher than two hundred seventy-five (275) volts shall be used underground, except for transmission, or for application to transformers or other apparata, where the high-voltage circuit is stationary. High-voltage motors, and transformers, shall be installed in suitable chambers, built of fire-proof construction, and well ventilated, and shall not be placed on intake, or between intake and return air courses. All high-voltage lines lines and apparata must be clearly marked, to indicate their danger. Main and distribution switchboards for high voltage shall be made of insulating and incombustible material, such as marble or slate, and to be free of all metallic veins, or of material equivalent thereto. Same shall be installed in a dry place. All switches or other instruments used in connection with high voltage shall be installed on suitable switchboards, with at least a three-foot passageway in front and rear properly floored, and kept looked by a door at each end that can be opened from the inside without a key. With higher than medium voltage, there shall not be any live metal work on the front of switchboard, and the entry circuit must be protected by an oil breaker s"

Apr 1, 1932

The goal of the Bureau of Mines diesel engine research program is to reduce exhaust emissions and minimize the risk of fires and explosions caused by the use of diesel- powered equipment in underground mines. This program has led to a fundamental understanding of the problems and to solutions that allow diesel equipment to be used safely and effectively. This volume contains reports of the presentations made at the Bureau Technology Transfer Seminar on Diesels in Underground &fines given in Louisville, KY, and Denver, CO, on April 21 and April 23, 1987. It also contains three reports of related research, not presented at the seminar, which highlight the significant achievements of a joint US.-Canadian research program on diesel emission control technology for underground mines. Topics covered in this volume include discussions of industrial hygiene problems associated with the use of diesels, accident statistics, fire and explosion control systems, measurement of diesel pollutants, emission control techniques including engine maintenance, fuel additives, diesel particulate filters, and ventilation of diesel sections. An alternative to diesel power, the hydrogen-powered mine vehicle, is also described.

Jan 1, 1987

By M Barker, H Li

The total number of tailings accidents has reduced from over 50/decade in the 1960s-1980s to less than 30/decade in the 2000s to 2010s. However, the rate of significant tailings dam failures has not been reduced. The significant tailings dam failures the mining industry experienced in the recent history include: Merriespruit, South Africa, 1994; Los Frails, Spain, 1998; Kolontár, Hungry, 2010; Mount Polley, Canada, 2014; and Samarco, Brazil, 2015. The conventional Factor of Safety approach itself may not be enough to further reduce the rate of significant tailings failures due to its limitations such as uncertainty. For example, the same factor of safety could have a vast range of annual probability of failure for different tailings dams, and insufficient consideration of failure consequence. This paper presents a risk based approach for design with the objective being to minimise tailings dam failures, especially those significant tailings failures with high consequence and low probability. This approach includes risk based design and risk management using bowtie tools. In the risk based design, quantitative analysis will be used to estimate the annual probability of failure and the tolerable failure criteria is linked to the consequence category. Bowtie analyses will be used to understand hazards and risks and identify and select independent controls that are effective in preventing and mitigating catastrophic failures. In this paper, examples of risk based design and bowtie analyses are presented and discussed. CITATION:Li, H and Barker, M, 2018. Risk-based approach for minimising tailings dam failures, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 397–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Y Yang

This paper discusses various issues surrounding the metallurgical control for furnaces, especially focusing on processes with long time-constants and æmetallurgical memoriesÆ. Examples will focus on furnaces accepting particulate and sometimes ill-defined feeds, eg submerged-arc furnaces, blast furnaces, secondary scrap smelting operations, recycling operations, waste incinerators, etc. Generally, because of the usually higher metallurgical time constant of these furnaces, these reactors have to be controlled in a feed-forward manner by the use of a hybrid of æblack boxÆ or empirical and ægrey boxÆ semi-empirical first principles metallurgical modelling and simulation techniques in a supervisory metallurgical control capacity.

Jan 1, 2000

By A. Nuric, S. Nuric, L. Kricak, M. Negovanovic, S. Mitrovic

"SynopsisRotary drilling with rolling tricone bits is the most widely used method for drilling large-diameter blast-holes in large surface mining operations. This drilling method is applicable to a wide range of soft to hard rock materials. This paper presents a fuzzy model for predicting the penetration rate of tricone rotary blast-hole drilling. The model is based on data obtained during the drilling of blastholes in rocks with various uniaxial compressive strengths in the Veliki Krivelj open pit mine, Bor, Serbia. The model was developed using the fuzzy logic toolbox of MATLAB with the Mamdani inference system. The fuzzy model was tested with 23% of the total dataset. The results obtained show the high reliability of predicting the penetration rates. Although there are possible limitations in applying the model to other open pit mines because of differences in rock properties, the prediction methodology applied in this paper can be used in many other predictions of the penetration rates.IntroductionAccording to Tamrock, rotary blast-hole drill operations depend on four important elements:•,Torque in the drill string drive sufficient to turn the bit in any strata encountered•,A high bit loading capability (pulldown force) sufficient for optimum penetration•,An air volume sufficient to remove chips generated during the drilling and to provide cool air to the drill bit bearings•,The selection of the proper type of bit for the material being drilled (Tamrock, 1984).The effects of rock mass parameters on the choice of the type of tricone bits were investigated by Kricak (1997)."

Jan 1, 2015

By Paul Hatmaker

This paper covers briefly the particular field of dolomite and magnesium limestone; certain uses of high-calcium limestone are mentioned only to show more clearly the limita¬ tions of the magnesian rocks. Such a comparison is helpful because magnesium carbonate is essential for some uses; for others it is immaterial; and for many its presence in an appreciable amount is objectionable. Magnesium carbonate, occurring as a rock resembling limestone or dolomite, is described in United States Bureau of Mines Information Circular 6437, Magnesite. Other com¬ pounds of magnesium are described in United States Bureau of Mines Information Circular 6406, Magnesium Compounds (Other Than Magnesite). Limestone, geologically, is a rock composed essentially of calcium carbonate; commercially, however, the term may include dolomite and magnesium limestone.

Sep 1, 1931

By Rodger C. Fry

Underground coal mining has been active within the East Mountain property since the mid 1950's. As a result, coal from two seams has been extracted within large areas allowing surface subsidence to occur. Monitoring of subsidence annually, began in 1981 using on the ground conventional monumentation, surveying and photogrammetric monitoring. The data collected has shown the time benefits of photogrammetry and the relationship between observed subsidence and the geometry of the mined out area below.

Jan 1, 1986

By Steve Dubnewych, Jon Kaneshiro, Calvin Jin

The Joint Water Pollution Control Plant (JWPCP), operated by the Sanitation Districts of Los Angeles County (the Districts), treats wastewater generated by over3 million people and processes wastewater solids generated by over 5 million people. The JWPCP Tunnel and Ocean Outfall Project, if constructed, would be one of the major marine outfall projects in the world. The new tunnel and ocean outfall system would provide relief to the existing outfall and allow inspection, maintenance, and repair of the existing tunnel and outfall system, portions of which were constructed as early as the 1930s. Geologic conditions are challenging along the alignments within the study are a being considered. Conditions include saturated alluvial soils, weak sedimentary rock, mixed face conditions, and squeezing ground conditions. Other significant challenges include the potentials for encountering up to 11 bars of water pressure, crossing seismically active faults, and encountering gassy and contaminated ground conditions. This paper discusses the details of the proposed project and the associated challenges.

Jan 1, 2007

By Joseph A. Holmes

The investigations carried on at the fuel-testing plant of the United States Geological Survey at St. Louis in 1904-1907 included tests of the steaming and gas-producing qualities of many coals and of the possibilif3 of their improvement by briquetting, together with washing and coking tests and tests of some of the resulting coke in the cupola. These tests were part of a general inquiry into the manner of utilizing most efficiently each of the coals under investigation. The equipment used in the cupola tests of coke, the manner of conducting the tests, and the essential results have been described in publications of the Geological Survey," and only the more important conclusions to be drawn from the tests are mentioned in the following pages. The tests were made to show the fitness of the cokes for foundry purposes, but an incidentlll result was to show foundry men and the coke producers the advisability of studying the conditions of foundry practice. The present bulletin, published by the Bureau of Mines because the analyzing and testing of fuels have been transferred from the Gilological Survey to the Bureau of Mines, briefly reviews the status of the coke industry, some features of practice in the use of coke in the foundry, the probable happenings of a cupola heat, and the reasons for modifying charging practice so that a particular coke can be used to best advantage.

Jan 1, 1910

In the past decade, the increased engagement of business in debates around sustainable development has prompted recognition of the importance of biological diversity at the local, national and global scales. Driven by increasing populations that demand rising real incomes, a range of human induced pressures are modifying natural habitats and diminishing their ability to support life. Public policy changes have struggled to arrest the loss of habitats such as wetlands or tropical forests, and the related extinction of plant and animal species. Although conservation legislation and regulation were once the exclusive responsibility of government, new partnerships are now being forged that increase the role of the private sector and non-government organisations (NGOs) in developing and delivering conservation initiatives. Since the mid 1990s Rio Tinto has had to adapt to meet the demands of a rapidly changing conservation landscape. When Rio Tinto adopted its statement of business practice in 1998 The way we work, it explicitly recognised the need to take account of relevant environmental factors in obtaining access to lands, particularly in designated areas of high conservation value. With the revision of The way we work in April 2003, the policy on land access was strengthened through removal of the word ?designated?, thereby signalling recognition of the importance of biodiversity outside of protected areas. In addition, Rio Tinto?s revised land access policy explicitly refers to the use of land that is surplus to operational requirements for habitat protection and biodiversity conservation, subject to social considerations. In late 2003 Rio Tinto further strengthened its commitment to biodiversity with the promulgation of its biodiversity strategy and related position statement, biodiversity principles? (See Appendix 1.1) and technical guidance documents. This commitment is also embodied in a variety of initiatives at the corporate and operational levels, which are reported on annually in Rio Tinto?s Social and environment review. This guide has been prepared to support the practical implementation of Rio Tinto?s biodiversity strategy. The purpose is to provide guidance on how to effectively integrate biodiversity into Rio Tinto?s operations. It is applicable to all Rio Tinto exploration, new development projects and operations, irrespective of whether they have been operational for some years or are at the beginning or end of their operational life cycles. This guidance has been developed to support the Rio Tinto Environment Standards and the Rio Tinto Community Standard and any additional supporting documents as they are developed.

Apr 1, 2005

"These tentative coal mine inspection standards have been prepared as a guide for the Federal inspection of coal mines of the United States. Much time and thought have been spent by various members of the Safety Division in the preparation of thses standards, and it is believed that compliance with them eventually will be possible in most mines. In many instances objections will be raised to them owing to long-established mining customs and practices that are inherently of dubious safety and to a natural inclination to oppose change. In other instances there will be valid objections due to conditions not foreseen at the time these standards were prepared. Or there may be substandard conditions and practices due to original mine layouts that it is not practicable to change during the lifetime of the mine; in such instances it is likely that some effective measures are or can be taken toward lessening hazards.With the rapid change in mining methods some of the standards may become inapplicable and it may be advisable to revise them to meet the new conditions. Therefore, questions regarding these standards and suggestions regarding new standards should be brought to the attention of the supervising engineer of the Coal Mine Inspection Division so that modifications of and additions to these standards may be made from time to time.In many respects these standards exceed the provisions of the various State mining laws, and some may conflict with the laws of some States. In cases of conflict, the intent is not to advocate noncompliance with State laws but to suggest that it may be desirable for the State to reconsider such laws or safety orders.Although an effort has been made to word these standards so that they may be readily understood, nevertheless, a reasonable interpretation should be placed upon them. In fact, in numerous instances the words reasonable"", ""suitable"", and ""properly"" are used in recognition of the fact that reason- and sound judgment enter into the carrying out of the safety endeavor.The policy of the Bureau on some vitally important safety matters in mines is set forth in its published Safety Decisions. These decisions have been consulted and used in the preparation of these standards. These decisions also are now being reexamined by its Mine Safety Board."

Feb 1, 1942