Search Documents

Underground coal mine tracked vehicles have been studied to determine the state of the art and how brakes might be added to the coal haulage cars. Specific areas of interest are: brake sys terns, couplers, car trucks and car handling procedures. Problems related to adding brakes to the haulage cars appear to be: the limited amount of room to mount the brakes on the cars, brake line connection between rotary dump cars, achieving desirable braking characteristics without over complicating the system and keeping the installation cost to a reasonable figure. This document combines the information contained in the first issue of the "State-of -the-Art of Underground Coal Mine Tracked Vehicle Brake Systems," BRL Report No. 6080, with that contained in a subsequent monthly report.

Jan 1, 1973

By P. E. Damon

An arsenal of isotopic techniques is avail-able that can date the full range of hydrothermal ore deposits. The following are prerequisites for ideal results: (1) Careful collection of samples that are related to the event in a field and process context; (2) Optical examination of the component selected for dating to be sure that it has not been altered; (3) Careful preparation of a pure component of the sample selected for dating; (4) Precise and accurate measurement; (5) Knowledgeable interpretation of the data with reference to decay systematics, properties of the component analyzed as well as the field context and thermochemical environment of the ore process.

Jan 1, 1992

By B. W. Gandrud

[The Bureau of Mines is conducting an extensive investigation of coal preparation in the Alabama coal fields in cooperation with the University of Alabama and coal-mine operators. In this investigation the drainage characteristics of typical coals from the Warrior and Cahaba n fields were studied. Tire main purposes of this study has been to evaluate no nearly as possible relative influences of certain factors on rate of drainage and to determine whether the drainage characteristics of coals from different beds or from different mines on the soma bed differ materially. A further objective was the development of a laboratory drainage test that would predict approximately the rate at which any coal will drain after having been loaded into a railroad car in a saturated condition. The study has been confined to samples of slack coals - that is, coals from which none of the fine sizes have been removed. The samples ranged in upper size limits from 7/16 inch to 3 inches. It did not seem necessary to study nut and egg sizes, that is, sizes from which the fine coal has been removed by screening, as these lose water so rapidly by natural drainage that they present no serious problem in dewatering after treatment in a washer. The significance of drainage characteristics of Alabama coals is apparent in view of the fact that not less than 70 percent of Alabama?s total coal product is subjected to wet washing before being materials.]

Jan 1, 1941

By William E. Greenawalt

IN these days of special legislation for the benefit of various industries one might well consider one branch of human endeavor intimately associated with engineering-that of patents and patent litigation. It is estimated that 85 per cent of all industries in the United States are based directly or indirectly on patents. Most inventors are engineers, and most patent litigation pertains to the engineering industries. It is fitting, therefore, that engineers should be vitally interested in discussing patent affairs, particularly as inventors are not a professional group, and invention is mostly a transitory phase incident to the development of specific industrial problems.

Jan 1, 1937

By G. W. Jones

From evidence made available during the investigation, it was concluded that the first of a series of explosions occurred at 1:15 to 1:20 p.m. September 21, 1951, in an underground vault that housed pressure regulators on the gas-distribution lines that served Brighten. This explosion damaged the pressure regulators and permitted high-pressure gas to enter the distributing mains and individual-service lines. As a part of the gas-distribution system was not provided with means for protection against such excessive pressures, gas gained access to the interiors of many residences in this area and caused a series of disastrous explosions and fires, which took place during a period of approximately 2 hours after the initial explosion in the pressure-regulator vault. Two persons were killed in the first explosion in a residence, and a third person died of a heart attack attributed to the excitement that prevailed during the explosions and fires, Twenty-three persons were listed as injured. Forty-one residences were either destroyed or damaged - 11 by explosion and the remainder by fires, which developed as a result of gas leakage into residences. Fifteen residences were listed as "completely down" or "gutted." Unofficial estimates of property damage ranged from $1,000,000 to $1,500,000. In view of observations made and information obtained during the investigation, recommendations are presented in this report relative to the natural-gas distribution system in Brighton, which may be helpful in the prevention of similar accidents in this and other communities.

Jan 1, 1952

By August J. Kwitowski

This Bureau of Mines report summarizes the development of a protective operator compartment for a new generation thin-seam mobile bridge carrier. The developed compartment is commercially available and is currently employed on approximately 15 bridge carriers used in the mining industry. The design of the compartment, which employed human factors engineering and small- and full-scale mockup models, is fully described. Details of the compartment's fabrication, evaluation, and demonstration in a commercial low-seam coal mine are also provided.

Jan 1, 1986

By J. R. Bartels

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Two sin-diameter 6x25 fiber core (FC) ropes were degraded on a bending fatigue machine, These were the second and third ropes in a series of tests on this construction and size rope. Tensile and nondestructive tests were performed on samples of the rope to determine the relationship between rope deterioration and rope breaking strength. The tests indicated that once a wire rope nears the end of its service life, both deterioration and the consequent loss of rope strength begin to increase at an accelerated rate.

Jan 1, 2010

By W. F. Watts

The U.S. Bureau of Mines has conducted research on methods to reduce and to measure diesel particulate matter (DPM) aerosols in underground coal mines. One objective of this report is to present findings from an investigation of the DPM reductions obtained by an engine-mounted integrated control system consisting of a dry system (DS) and a diesel particulate filter (DPF). Another objective is to present results from the usc of a size selective personal sampler to measure DPM concentrations in an underground coal mine. Bureau laboratory tests of the integrated dry system and diesel particulate filter (DS-DPF) have shown that DPM emissions can be reduced up to 97 pet with little change in gaseous emission concentrations. The DS-DPF is undergoing certification tests conducted by the Mine Safety and Health Administration (MSHA). Subsequent to passing all safety requirements, it will be tested in an underground coal mine. A baseline survey of DPM concentrations and aerosol size distributions in a cooperating mine was completed in August 1988. A prototype DPM personal sampler was tested during this survey. Based on results from this test, an improved unit has been developed. This unit is scheduled for extensive field testing by MSHA in 1989.

Jan 1, 1989

What is a nugget effect? In the early development of geostatistics, the term ?nugget effect? was coined for the apparent discontinuity at the beginning of many semivariogram graphs. This name was chosen to reflect the large differences found between neighbouring samples in ?nuggety? mineralizations such as Wits gold reefs. Geostatistical theory assumes that the difference between a sampled value and a potential repeat sample at the same location is actually zero. Included in this ?nugget effect? would be true variation between contiguous samples due to the nature of the mineralization, micro-fracturing, nugget or crystal size, and so on. Also included in the nugget effect would be any ?random? sampling variation which might occur due to the method in which the sample was taken, the adequacy of the sample size, the assaying process, etc. Arguments were put forward that ?sampling errors? actually exist at zero distance. Some geostatistical schools actually maintain that the ?nugget effect? is all sampling error. This would imply that ?perfect? sampling would eliminate the nugget effect entirely. There is now a dichotomy both in the geostatistical world and in the software packages provided for geostatistical analyses. It may seem academic to argue over whether the semivariogram model should take a value of zero, a value equal to the nugget effect, or a partial value at distance zero. However, the decision can have a profound effect on both the estimated resource and in our confidence on that resource. Whereas most geostatistical texts define the semivariogram model as taking the value of zero at zero distance, others imply that the full nugget effect should be used at zero distance. For example: ?The nugget effect refers to the nonzero intercept of the variogram and is an overall estimate of error caused by measurement inaccuracy and environmental variability occurring at fine enough scales to be unresolved by the sampling interval3 ?Christensen4 has shown that the ?nugget effect?, or non-zero variance at the origin of the sernivariogram, can be reproduced by a measurement error model ?The nugget effect is considered random noise and may represent short-scale variability, measurement error, sample rate, etc.5. In many training texts and Web courses, the definition of the semivariogram is ambiguous as the formulae for semivariogram models is not actually specified at zero distance6,7,8.

Jan 1, 2010

By Deno M. Pappas

The purpose of this Bureau of Mines study of U.S. roof and rib (roof- rib) accident statistics and related accident costs is to define current accident trends (1980-84) associated with fatal and nonfatal roof-rib fall accidents. Data were retrieved from a data base containing all recorded U.S. mining accidents, then sorted and normalized utilizing a computer software program. The statistics indicate that roof-rib accidents have significantly declined in the 5-yr study period. Moreover, they indicate that there have been increases and/or patterns of roof-rib accidents associated with specific mine characteristics, such as seam height, mine size, geographic location, and seasonal variations. Also, roof-rib injury characteristics produced pattern changes involving worker activity, lost workdays, types of injury, and severity of injury. A conservative estimate indicates that there has been a 30% adjusted increase in the cost of a roof-rib accident over the 5-yr study period.

Jan 1, 1987

By D. L. Soreck

The hazards to the public posed by abandoned mine shafts are well documented. As private development encroaches on previously mined areas, the potential for fatalities and serious injuries from abandoned mine shafts increases. The U.S. Bureau of Mines has conducted research into cellular concrete as a material for sealing these openings. The current work involves testing the characteristics of cellular concrete before and after it had been pumped or dropped from different heights into a simulated mine shaft. Cellular concrete was pumped vertically up to and subsequently dropped from heights of 18 and 37 m into concrete forms. Wet density measurements were made at multiple sampling points in the test circuit. Air content determinations and uniaxial compressive strength testing were conducted. Research results showed significant loss in air content and changes in the characteristics of cellular concrete during pumping or dropping from various heights. Recommendations on effective use of cellular concrete for sealing abandoned mine shafts are made.

Jan 1, 2010

By Y. Luo

A PC based computer model has been developed by the authors for predicting the surface subsidence due to underground coal mining. Its reliability, comprehensiveness and user friendliness demonstrate that it is a good tool for the mine operators, government agencies and scientific researchers alike.

Jan 1, 1989

By David C. Oyler

The U.S. Bureau of Mines studied the interaction of longwall shield supports and adjacent strata at the Meigs No. 31 Mine in southeastern Ohio. Twenty-three legs of twenty shields at midface were instrumented with pressure transducers and monitored for 11 weeks. During the project, leg setting pressures were reduced twice to determine the effect of setting pressure on shield-strata interaction. No correlation was observed between setting pressure and leg loading rates. The shield loading profiles were consistent with a model in which the roof consists of two zones, a thin immediate roof loading the shields well below the typical setting force and a main roof zone essentially supported by the coal and gob and loading shields through its convergence. This model was used to develop an equation for estimating average loading rates at the site. The only variable of the equation is time, and the equation consists of an exponential term to account for the immediate roof loading and a linear term to account for main roof loading. The equation gave good correlation with average loading rates, but the variation in loading from cycle to cycle was too great for the equation to give good predictions of individual cycle loading rates.

Jan 1, 2010

By Jennifer Riefenberg

Research efforts by the U.S. Bureau of Mines include running a series of displacement-discontinuity, boundary-element models to simulate the gateroad design at an underground coal mine in northwestern Colorado. The initial mine design is a yield-abutment chain pillar arrangement in a three-entry, longwall gateroad system. Pressure effects from mining the first and second panel were recorded using borehole pressure cells (BPCs). These field data were then compared directly to the model output. Observed yielding in the field was approximated by reducing material property values and/or removing pillar elements in the model. Model results using this calibration technique mirrored the field measurements consistently. Using the calibrated model parameters, a suite of models was run simulating an experimental entry design: exchanging the yield and abutment pillar locations. These model results reflect a 20¬to 33-percent reduction in core stresses in the yield pillar during mining of the second panel. Improved pillar and entry conditions are suggested by these predictive results. The design modifications were then implemented at the mine along a 150-m (500-ft) test section. Field observations and measurements from the experimental design test site compared favorably with trends of the model predictions.

Jan 1, 1993

By Robert F. Chaiken

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,000° C (1,832° F), and can be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated, but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project, to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fourth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 3, 4, and 5). Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. This part (part 4) and part 5 both deal with the closeout phase of the field demonstration. The quenching of the fire is described in this report, and part 5 will describe the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration, which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection with fume exhaustion is a potentially effective method for cooling large underground fire zones. Further trials of both Burnout Control and water injection with fume exhaustion are planned.

Jan 1, 1984

By W. L. Dare

This publication is one of a series prepared by the Federal Bureau of Mines on methods and costs of producing uranium ore on the Colorado Plateau. The information it contains was gathered in 1955-58 and applies to eight small operations. (See fig. 1.) Mining costs have increased since the data were I collected, but the information should be helpful in estimating future costs I at similar deposits. The Bureau of Mines had early experience in the production of carnotite-type ores on the Colorado Plateau.3 4/ Under a cooperative agreement with the National Radium Institute in 1914-16, the Bureau mined and concentrated carnotite ore for recovery of radium, uranium, and vanadium. The ore was taken from claims in or near Long Park Montrose County, Colo., about 3 mi. south of La Salle Mining Co.'s La Salle mine, which is one of the mines described in this report. The Bureau leased the claims from Crucible Steel Mining & Milling Co., a subsidiary of Crucible Steel Co. of America, and from 1914 to 1916 produced 990 tons of high-grade ore, containing 2.6 pct. U308, and about 2,000 tons of mill-grade ore, containing 0.85 pct. U308. The high-grade ore was shipped directly to a radium-recovery plant built in Denver in 1914 under the cooperative agreement. There, commercial methods of extracting uranium, vanadium, and radium from carnotite ores were developed by Bureau personnel. The lower grade ore was concentrated at a small mill in Long Park before being shipped to Denver. The final recovery was 69,000 lb. of U308 and 8.8 g. of radium. The direct mining cost of producing the high-grade ore, including the labor to hand sort and sack it, was $35.96 per ton. Freighting the ore 58 miles to Placerville, Colo., the nearest rail point on the Rio Grande Southern Railway, cost $25.28 per ton, which included $4.55 per ton for ore bags and twine. Four-or six-horse teams pulled two wagons in tandem and made the

Jan 1, 1961

By B McFadzean, N P. Lima, D A. Deglon

The reverse flotation of Itabirite iron ore is typically performed after a desliming step in which most of the sub-10 µm particles are removed. This is done to limit processing problems such as poor flotation recovery of SiO2 due to slime coatings and increased slurry viscosities, unmanageable froths and increased losses of hematite particles due to entrainment. However, the rejection of ultrafine particles contributes to large losses in iron recovery and may contribute to the instability of tailings dams. The aim of this study is to decouple the effects of ultrafine particles in the pulp and froth phases to better understand the processing capabilities of the fines fraction. The flotation test work was performed in a special-purpose continuously operated laboratory flotation cell that has a deep froth section to simulate plant-scale froth conditions. Five conditions of fines addition were investigated at three different froth heights and a solids concentration of 50 per cent. The behaviour of the pulp and the froth were decoupled using froth stability and froth recovery tests. This showed that, even though there is an exponential increase in froth stability at increasing fines quantities, the performance of the pulp has the overriding effect on the overall SiO2 recovery. Pulp zone, froth zone and overall SiO2 recoveries showed that overall recoveries increased by about 3.6 per cent for every 1 per cent decrease in fines content. This meant a large increase of 20 per cent in SiO2 recovery when going from undeslimed to deslimed feed. This was driven largely by increases in the pulp zone recoveries, which were about 4 per cent for every 1 per cent decrease in fines content. The froth recoveries, on the other hand, decreased by between 0.75 per cent and 2.5 per cent for every 1 per cent decrease in fines content, depending on froth height. This paper explores further insights into iron ore flotation processing at different slimes concentrations.

Aug 24, 2022

By John A. Owsiany

The effect of longwall mining on streams and shallow aquifers has been the subject of numerous research studies for more than twenty years. As a result of these studies, it has become common to consider an overburden thickness of 400 feet as the lower limit at which longwall mining methods may be used with little or no effect on hydrologic systems. This paper presents the results of a study documenting the response of a large high order stream to shallow cover undermining by longwall methods in the northern Appalachian coalfield. The field site is located in a narrow stream valley where the overburden, composed primarily of limestone and sandstone units interbedded with shales and siltstones, ranges in thickness from 340 to 285 feet above the main bench of the Pittsburgh coal seam. Streamflow monitoring and monitor well measurements indicate that no significant loss zones or water table lowering resulted from undermining the stream or the adjacent valley bottom area. Additionally, hydrographs for shallow near-stream wells exhibit fluctuations related to natural seasonal variations, which are nearly identical to those observed in a non-undermined control well in the same watershed. Environmental factors affecting streamflow were monitored through the use of a control stream in an adjacent non-undermined watershed to differentiate between natural and mining induced changes in flow.

Jan 1, 2001

By J. H. Crary

This report summarizes the results of a one-year agreement for research on the electromagnetic environment in coal mines, which was conceived as the beginning of a long term cooperative program between ITS and the Bureau of Mines. The concepts on which it was originally based are a result of the report on mine rescue and survival by the Committee on Mine Rescue and Survival Techniques of the National Academy of Engineering, dated March 1970. This report drew particular attention to the need for improved communications during and following mine disasters. In particular, the outstanding problems identified were the location of, and communication with, trapped miners. Some tentative solutions, generally involving long-wave electromagnetic signals, were offered. Consideration of the problems of disaster location and communication soon leads to consideration of the communications techniques (or lack of them) for use under normal mining conditions. In particular, if a disaster communication and/or location system is to be readily available and operable under disaster conditions, it should also be usable during mining operations. In this way operators can become familiar enough with the system to operate it during disaster conditions, as well as provide a mechanism for regular testing.

Jan 1, 1972

"INTRODUCTION Early in 1936 the Interstate Oil Compact Commission and other groups interested in forecasts of demand for petroleum requested the Bureau of Mines to make a physical inventory of crude-oil stocks in the United States, Accordingly, the 74th Congress appropriated funds for conducting such a survey during the fiscal year ended June 30, 1937. In the discussions and hearing 2/ relative to the need for the survey, the opinion was expressed that crude oil held in storage for long periods had lost so much of its gasoline content that the economic significance of total stocks should be discounted materially. Therefore, a primary objective of the survey was to make a physical inventory of the crude oil held in storage above ground and to determine the quantities and characteristics of the light fractions contained in the various stocks."

Sep 1, 1938