Search Documents

By Z. Zhang, Zongshu Zou, Nan Wang

"Thermodynamic calculation is applied to make an investigation on the equilibrium phase relations and liquids of CaO-SiO2-Al2O3-FeOx system for different temperatures. The calculated results with FactSage6.1 show that the effect of temperature on the the equilibrium phase relations and liquidus of CaO-SiO2-Al2O3-FeOx system and its sub-systems is appreciable. The liquid phase regions enlarge with increasing temperature from 1573K to 1873K, while the primary phase fields reduce distinctly.IntroductionThe main oxide components of vitrified bottom ash slag are CaO, Al2O3, SiO2, Fe2O3, MgO, and Na2O, accounting for more than 90% of the bottom ash by weight[1]. During slag processing, the knowledge of thermodynamic properties and liquidus temperature in the related slag systems is highly required [2, 3], which is not yet available. Through literature survey [4-6], it is clear that the systematic information on the concerned complex slag system is scarce. So far the engineers in the field have to make assumptions of the thermodynamic properties of the simplified oxide system, without taking into consideration the interactions of the different oxide components, which hinders the development of the slag valorization and utilization. In order to provide thermodynamic properties for the application of the vitrified bottom ash, the six-component oxide system (CaO-MgO-Al2O3-SiO2-FeOx-Na2O) is highly required. A preliminary phase diagram of the CaO-MgO-Al2O3-SiO2-FeOx-Na2O system can be obtained from extrapolation of the thermodynamic functions of constituent subsystems such as CaO-SiO2-FeOx-MgO, CaO-SiO2-FeOx-Al2O3, CaO-SiO2-Na2O-MgO and CaO-SiO2-Na2O-Al2O3. In this work, the equilibrium phase relation and liquidus of CaO-SiO2-FeOx-Al2O3 system, one subsystem of the concerned complex slag system, are calculated and the effect of temperature is also discussed."

Jan 1, 2012

By Anestis Vlyssides, Elli Maria Barampouti, Sofia Mai, ?postolos Vlyssides

"A new anaerobic reactor variation, the UASB/CO2-stripper reactor was conceived. It consisted of a conventional UASB reactor that recirculated the biogas produced. The sludge characteristics of this system were examined when treating high strength wastewater. From the data collected, it was obvious that the UASB/CO2-stripper system can satisfactorily operate at higher loading rates (25 g COD·L-1·d-1). A pronounced effect on the quality of the granular sludge was observed. The VSS/TSS ratio decreased sharply. A considerable decrease in the mean granule diameter was observed, while the specific gravity of the granules increased. The sludge bed porosity increased significantly leading to a considerable expansion of the sludge bed. These changes in the sludge properties led to a gradual shift of the system towards a fluidized bed process as far as its hydraulic characteristics were concerned.IntroductionIn recent years energy considerations and environmental concerns have increased the interest in direct anaerobic treatment of industrial wastes. The anaerobic method of waste treatment offers, under the present circumstances, a number of significant advantages with trivial or more serious drawbacks over other treatment methods. The major obstacle to the application of the process for this specific purpose is perhaps the difficulty of extending it to a stable and simple operational form. A number of reactor configurations has been developed leading to high biomass concentrations, e.g. the contact process, the filter reactor, the UASB reactor, and the fluidized bed systems, but the process stability problem still remains [1].A prime objective in the operation of anaerobic waste treatment process is the maintenance of a proper pH range. Thus, a possible solution to the process stability problem could be obtained by increasing alkalinity in the anaerobic systems. Therefore, the main objective of this paper is to present and evaluate the results of a system (UASB/ CO2-stripper) with increased alkalinity concentrations."

Jan 1, 2008

By Hai-Xing Fang, Bing Xie, Hong-Yi Li

"In the duplex melting process, chromium forms chromium spinels, the study of which will help to exploit the Hongge ores (rich in chromium) in the Panzhihua-Xichang area in China. Mimicked chromium slag was synthesized. The oxidation and decomposition mechanism of the Fe-Cr spinels contained was studied in a sodium roasting process. The effects of temperature, roasting time, amount of soda added and filling reagents were investigated. The leaching-reduction-precipitation-calcination procedure to extract Cr2CO3 was optimized. The results showed that the optimized roasting temperature was 1000~1020°C with a stoichiometric Na2CO3 addition and without any filling reagents. Roasted materials were leached with distilled water and were filtered to obtain a chromium-containing solution, which was adjusted to pH 1.60-1.80. A reducing reagent, NaHSO3, was added in a stoichiometric ratio and the solution was then adjusted to pH 7.25~8.25. Maximum Cr2O3 precipitation was obtained and the precipitate was calcined at 1050°C for 2h to obtain Cr2Ü3 with recovery rate over 96%.IntroductionChromium is widely applied in the metallurgical industry, in refractory materials and in the chemical industry with its particular properties of hardness, wear-resistance, high temperature resistance and corrosion resistance [1]. There is no free state of chromium in nature and chromite is the main chromium containing mineral [2], China is poor in chromium resources, despite its large demand, and there are few deposits of high grade of chromite ores except in some regions in Tibet and Xinjiang province [1, 4]. Hongge, one of largest titanomagnetite mines in Panzhihua-Xichang area, is a polymetallic deposit mainly containing iron and titanium; it is also associated with various beneficial elements such as chromium, copper, nickel, etc. [3]. As investigated in Reference 3, the chromium reserves of Hongge ores are so large that it is of great importance to study how to extract the chromium from them."

Jan 1, 2012

By Michal Rzyman, Nakamura Takashi, Shibata Etsuro, Grabda Mariusz, Oleszek-Kudlak Sylwia

"Thermodynamic considerations indicate that heavy metal oxides should easily react with HBr, the main gaseous product from the thermal decomposition of tetrabromobisphenol A (TBBPA), forming low boiling point metallic bromides suitable for volatile separation. Mechanisms and kinetics of the bromination reactions must be well recognized prior to developing of a new treatment for the simultaneous recycling of plastic waste containing brominated flame retardants (BFRs) and metal oxides (printed circuit boards, automotive shredder residue, plating sludge, metallurgical dusts). In this work, a differential scanning calorimeter and laboratory-scale furnace were used to investigate the possibility and conditions of the bromination of ZnO by product of thermal decomposition of TBBPA. The formed solid, condensed and gaseous products were analyzed by X-ray diffraction analysis, electron probe microanalysis, inductively coupled plasma analysis, ion chromatography and gas chromatography coupled with mass spectrometry. Introduction Tetrabromobisphenol A (TBBPA) is the largest volume brominated flame retardant (BFR) in production today and is used in more than 70% of the world’s electronic and electric (E&E) appliances [1]. The growth in the production of E&E products and the fact they become obsolete so quickly cause significant problems in the safe disposal and recycling of the electrical and electric waste (E-waste) and other BFR-containing waste [2]. Among various treatment processes, thermal methods are most useful since they allow the recycling and recovery of both the organic and inorganic fractions of the waste. However, incineration of the BFR-containing wastes results in the emission of hazardous organobromine compounds, while the main portion of bromine released from decomposed BFRs is present in flue gas as hydrogen bromide (HBr) [3]. HBr, which is known to damage incineration systems, seems to be a very effective bromination agent for many metallic oxides present in waste. The concept of this study is to take advantage this of its property."

Jan 1, 2008

By B. Boryczko, J. Norwisz, Jose Escobedo Bocardo, Z. Kolenda, A. Holda

"Classical thermodynamic analysis of any thermal and chemical process is usually based on the first law of thermodynamics. Such an approach is not sufficient when deeper understanding of the nature of each elementary process is required. The use of the first and second law of thermodynamics together is necessary to solve practical process more effectively. Enthalpy and exergy balances allow to enhance our understanding of thermal processes especially when cumulative consumption of energy and exergy is calculated. To ensure reliability of such an analysis the least squares method for adjustment of mass balances of principal chemical elements has been applied and described in detail. Numerical analysis has been carried out to compare two different processes of copper production – shaft furnace and flash smelting.IntroductionClassical thermodynamic analysis of any technological process is usually based on the First Law of Thermodynamics in the form of energy (enthalpy) balances. Such an approach is useful in engineering practice as it makes analysis easier in the global scale neglecting modeling of the elementary processes, allows calculation of the thermal efficiency and makes possible to control quality of the measurement results. Additionally, graphical presentation of the energy balance is simple in the form of Sankey diagram.In the case of aluminum electrolysis process, design of the new electrolyzer or its modernization is always based on the enthalpy balance.However, deeper thermodynamic analysis leads to the conclusion that such an approach is not sufficient. The First Law of Thermodynamics guarantees the exact equivalence of the various forms of energy (allowing all forms to be measured in the common unit such as joules) but it does not guarantee interconversibility. Thermal energy (heat) is in a peculiar and unique position, for whereas all other forms can be completely converted into thermal energy, the reverse process id impossible, only a portion of the heat can be converted into mechanical energy. Explanation comes from application of exergy balances. As we know exergy expresses the amount of mechanical work necessary to produce a material in its specified state from components common in the natural environment, in a reversible way, heat being exchanged only with environment [1]. Consumption of exergy connected with the fabrication of some considered product appears not only in the plant manufacturing the product, but also in all plants delivering raw materials for the final production process"

Jan 1, 2008

By Tuula Mäkinen

In 1959 Outokumpu started up an integrated nickel smelter and refinery at Harjavalta. The flash smelting ? Peirce-Smith converting route was applied, and the high-grade converter matte was further refined to nickel cathodes by leaching and electrowinning. In 1995 the production capacity was increased from 17 000 mtpa to 52 000 mtpa, based on the Direct Outokumpu Nickel Smelting Process. The additional refinery capacity is based on hydrogen pressure reduction, producing nickel powder and briquettes. The smelting operation is currently part of Boliden Group and the nickel refinery part of OM Group. In the DON technology, high-grade nickel matte with low iron content is produced in the flash smelting furnace directly without subsequent converting. The metal values in the smelting slag are recovered in an electric furnace as an iron containing Ni-matte. The mattes produced differ from the conventional nickel mattes in many respects, and therefore focused R&D efforts have been made in order to cope with their melting points, fluidities and settling properties. When developing and operating metallurgical processes it is crucial to manage and control the characteristics of the products as well as by-products generated in different steps of the process chain. The low melting points of the high-grade nickel mattes produced in the DON furnace, particularly those low in copper, have pointed out challenges in the furnace design, in particular in the hearth and its thermal engineering. Also key issues of the DON technology are smelting of high-magnesia concentrates, the recoveries of nickel and copper, as well as those of PGM`s and cobalt. These factors can be affected by a proper selection of the process concept, and the operational conditions in the processing vessels. This paper deals with the experience of the DON technology gained over the first ten years of operation, including the significant environmental impacts. Selected results of the thermo-dynamic modelling of DON and EF mattes and high-magnesia slags are reviewed, with the reference to the mattes produced. Also the design principles of the FSF and EF will be discussed.

Jan 1, 2006

By Ehsan Vahidi, Fereshteh Rashchi, Amirhossein Shahnazi

"The pig iron from steel manufacturing plants contains a high concentration of vanadium-bearing materials smelted with iron ore. During the oxidation process of the molten pig iron with oxygen lances, vanadium transfers to the slag. In this research, recovery of vanadium from LD (Linz-Donawitz) converter slag of steelmaking plant was investigated. The leaching residue was characterized by XRD and XRF techniques. The maximum vanadium recovery was achieved at optimum leaching conditions of 70 °C, S/L: 1/15, sodium hydroxide concentration: 3 M and leaching time: 150 minutes. The dissolution rate increased with rising sodium hydroxide concentration and temperature and decreasing particle size. The experimental data are treated graphically to explain the kinetics of the vanadium recovery process using shrinking core model (SCM). As a result, the controlling regimes in the SCM were analyzed separately using liquid film diffusion control, solid product diffusion control, and reaction control mechanisms.IntroductionVanadium is commercially important as a constituent of several alloys and catalysts. Nowadays, vanadium is mostly recovered as a by-product from secondary sources or from industrial waste streams such as titaniferrous magnetite, fly ash, spent catalysts, and petroleum coke. Steelmaking operations are specifically concerned by this problem due to the production of a huge quantity of by-products [1]. These by-products, including LD converter slag, sludge, fly ash, spent catalyst, ash, and alloyed scrap, contain a notable amount of heavy metals which may cause environmental problems. Solvent extraction is one of the techniques being increasingly used for the recovery of vanadium [2]. Apart from vanadium ore, secondary resources such as titanmagnetite, ilmenite and slag from the ferrous industry are a major source of supply. The pig iron from steel manufacturing contains a majority of vanadium-bearing materials smelted with iron ore. In a heat resistant shaking ladle the molten pig iron is oxidized with oxygen lances, causing the vanadium to be transferred to the slag. Normally, the vanadium in LD converter steel slag (coming from Linz-Donawitz steelmaking process) is ca. 5% as vanadium pentoxide (V2O5). This slag is the world's principal raw material for vanadium production [3, 4]. Moskalyk and Alfantazi [4] reported that a roast-leach process is used in South Africa for the production of vanadium oxides from magnetite ores while some of the slag was converted to ferrovanadium. A portion of the slag was exported to Europe for the production of vanadium oxide. The researchers mentioned that alkaline roasting was the main process at that time employed to extract vanadium pentoxide from vanadium slags."

Jan 1, 2012

By W. G. Davenport

Chapter 6 examined autotherrnal smelting of pure chalcopyrite concentrate with 50 mass% O2-50 mass% N2 blast. It showed that production of 1500 K products with this blast requires: 181 kg of pure oxygen 337 kg of air per tonne, of concentrate. It also showed that the grade of matte produced with this blast is 58% Cu. This chapter re-examines autotherrnal smelting by asking: (A) WHAT COMPOSITION BLAST (MASS% 02 -MASS% N2), 298 K, WILL AUTOTHERMALL Y PRODUCE 65% Cu MATTE 1500 K FROM PURE CHALCOPYRITE CONCENTRATE? (B) HOW MUCH PURE OXYGEN AND AIR WILL BE NEEDED? These are important questions for flash? smelting because furnace operators usually want to send specific composition matte to converting. This chapter shows how a specified matte can be produced autotherrnally with 298 K oxygen-air blast. Later chapters show how it can be done with hot blast, hydrocarbon combustion, different concentrates etc.

Jan 1, 2001

By W. G. Davenport

Most pre-t 988 Outokumpu flash furnaces were built with blast heaters. Many continue to use them. Blast temperatures in these smelters· are typically 400 to 700 K (Table 2. 1) This chapter: (a) shows how hot blast is included in our calculations (b) evaluates the effects orhot blast onauthothermal65% Cu matte production.

Jan 1, 2001

By Ahmet Geveci

[Generally accepted formula related to sulfur slag-metal distribution ratio is given by the following equation: [ ] According to the above equation it can be deduced that sulfur distribution between slag and metal is governed mainly by metal composition (?s term), slag composition (slag basicity and in turn sulfide capacity), oxygen potential of the system (ao¬¬ term) and temperature(related to equilibrium constant, K). In this study, the results of ladle furnace operations conducted in Erdemir-Iron and Steel Works Co. (Turkey) in relation to sulfur removal, have been given. Typical ladle furnace slag analyses of 4937K quality steel have been presented. Activity coefficient of FetO,?FetO, have been calculated with the relation obtained fromthe literature. Activity calculations have been performed with the program written in Mathcad. The changes in activity of aFetO in the slag phase,, have also been studied in relation to the sulfur removal: The relation between % Decrease aFetO and %DeS (measured)have been investigated for 4937K runs and someother types of steel produced in the Erdemir Plant. Related to ladle operations %desulfurization defined as [(%Sinitial-%Sfinal)/S%initial]*100 values have been presented for different steel qualities.]

Jan 1, 2006

By J. C. Riani

The release of heavy metals into the environment is increasing among others due to human activities such paint and pigment industries, tanneries, and metal finishing industries. Among metal releases, chromium is notable because this metal is carcinogenic. Thus, the aim of this work is to use an ion exchange system composed of one cationic resin column and one anionic resin column in order to adsorb the chromium (III, VI) from chromium electroplating effluents with the objective of recycling the water. The methodology consists of chromium adsorption tests using the ion exchange resins system with Purolite the 850 (polystyrene matrix, functional group quaternary amine) and Purolite C 150 (polystyrene matrix, functional group sulfonic acid). The contaminated solutions were passed through the columns with the assistance of peristaltic pump. Samples of the outgoing solution were taken in order to control the conductivity and pH and analyze the metals. The effects of the feeding outflow on the chromium adsorption were evaluated. The results show that the quality of the water collected at the end of the process is within the Brazilian standards about the discarding of toxic substances in the environment (CONAMA 357/05). This makes possible the recycling of water into the process and also its discharge in the rivers.

Jan 1, 2006

By C. A. Morais

The present work describes the development of an efficient and relatively simple process to obtain high grade CeO2 from a mixed rare earth chloride solution. The process involves cerium oxidation and precipitation by addition of a KMnO4-NaCO3 solution. The experiments were carried out at room temperature (25 1° C). The results indicated that the major parameters affecting cerium recovery are the molar ratio of KMnO4/Ce, the initial acidity of the chloride feed solution and final pH of Ce(OH)4 precipitation. In strong acid solutions (pH < 1), the oxidation of Cl to Clo took place in addition to the oxidation of Ce(III) to Ce(IV), so increasing the permanganate consumption. Conversely, low acidity (pH >3) led to coprecipitation of the other rare earth elements. Under the selected conditions, cerium was selectively precipitated as ceric hydroxide, together with some manganese dioxide. Further purification was carried out by the dissolution of Ce(OH)4 in HCl, followed by precipitation as cerium carbonate. The filtrate was neutralised with a Na2CO3 solution in order to recover the associated rare earth elements for further separation. The final product, assaying 99.7 % CeO2, was obtained with a recovery of nearly 100%.

Jan 1, 2003

By Yuri Bychkov

The Electron Beam Melting is the most efficient technology for metals and alloys refining. For ,secondary metals processing the Electron Beam Skull Melting (EBSM) with the electromagnetic stirnng (EMS) of melt in the crucible was shown to be the most appropriate. The copper produced by EBSM with EMS possesses higher density and electric conductivity in comparison with other refining methods. The details for high power electrical machines were cast of the copper waste refined by EBSM technology.

Jan 1, 1995

By W. G. Davenport

All Outokumpu flash furnaces burn some hydrocarbon fuel. Hydrocarbon combustion supplements heat from Fe and S oxidation and provides local heating in cool; parts of the furnace. Adjustment of hydrocarbon fuel combustion rate is an effective way of controlling furnace temperature. More oxygen and more oxidation of Fe?and S in the flash furnace continue to diminish the need for1hydrocarbon fuel. Still, as Tables 2.1 and 3.1 show, all flash furnaces use it. Oil is the most common fuel -natural gas, coal and coke are also used. This chapter demonstrates how hydrocarbon fuel is included in our flash furnace matrix. It shows that: (a) three new variables, mass hydrocarbonfoel. mass CO2 in offgas and mass H2O in offgas are inserted (b) carbon and hydrogen balances are added (c) hydrocarbon fuel quantity is specified (d) ,the oxygen balance is modified to include CO2 and H2O (e) the enthalpy balance is modified to include hydrocarbon fuel, CO2 and H20.

Jan 1, 2001

By Mingzhou Li, Lin Wu, Changren Tong, Fengli Yang, Shaohua Yang

"According to characteristics of Tm, Yb and Lu enriched oxides composition and problems in its traditional extraction separation process, the computer simulation of a optimized fuzzy extraction separation process, in which three products with high purity(>99.99%) could be obtained at same time, was carried out. Distributing Curves of every element in both organic and aqueous phases were worked out. Distribution rules of rare earth elements in every stage of the optimized extraction process were studied. The computation results of economical and technical index showed the consumption of the acid and base chemical reagents in the optimized process would be saved more than 30%.IntroductionFor the solvent extraction separation process of rare earths, countercurrent extraction process was widespread in the industrial practice. Normally, rare earth ions were extracted by the saponificated extractant and transferred into the organic phase, where the acidic extractant was saponificated by the base firstly. Then, the loaded rare earth ions were stripped from the organic phase into the aqueous phase by the acid. Therefore, the acid and the base were the main consumptions in the process, and the equilibrium acid of the stripped rare earth solution was one of the main pollution resources. Meanwhile, for the heavy rare earths, such as Tm, Yb and Lu, stripping was more difficult, and the equilibrium acidity of the stripped rare earth solution was higher, so the acid consumption increased greatly."

Jan 1, 2012

By Pradeep kumar Jha, Manas Mohan Mahapatra, Sabin Kumar Mishra, Satish Kumar Ajmani, Satish C. Sharma

"Due to mechanical/ electrical failure in the C.C. line or inadequate availability of molten steel from coming ladle, sometimes one/two outlets of a multi-strand tundish in continuous casting unit is closed. Closing any of the outlets affects the flow distribution inside the tundish which in turn governs the quality of steel coming out. Hence it is important to study which of the outlets should be closed to have proper results in terms of flow behavior and inclusion removal inside the tundish. Present study aims at finding the effect of closing one or two outlets on flow behavior and inclusion removal in a multi strand tundish. It was found that closing the near outlet (outlet near to the inlet) increases the inclusion removal tendency than closing the other two outlets in a six-strand billet caster tundish (only three outlets are considered because of symmetry).IntroductionContinuous casting process transforms molten metal into solid on a continuous basis. This process is the most efficient way to solidify large volumes of metal into simple shapes for subsequent processing [1]. Molten metal is tapped into the ladle from furnaces. From the ladle, the hot metal is transferred via a refractory shroud (pipe) to a holding bath called a tundish. The tundish allows a reservoir of metal to feed the casting machine while ladles are switched, thus acting as a buffer of hot metal as well as smoothing out flow, regulating metal feed to the moulds and cleaning the metal [2]."

Jan 1, 2012

By James D. Navratil

Ferrites have been used to separate a wide range of substances such as dissolved metal species, particulate matter, and organic and biological materials; they have been used almost exclusively for metal waste treatment applications. The versatility of the ferrite waste treatment technique is evident in the wide variety of application methods. Furthermore, ferrites can be used to remove selected impurities in feed solutions containing metal products requiring purification. A brief overview of ferrite properties and recent applications for metal recovery and waste processing will be presented.

Jan 1, 1990

By Tatsuki Uzawa, Takashi Nagai

The consumption of Nd and Dy is increasing dramatically because of an exceptionally high demand for Nd-Fe-B-(Dy) magnets and a significant amount of the magnets are wasted. It is important to develop a recycle process the elements from the wasted magnets. In this study, Nd and Dy were extracted from the magnets by silver at high temperature. Nd can be extracted more than 70 % by silver. However, Dy is extracted only 25 % in the same experimental condition.

Jan 1, 2014

By A. V. Tarasov

The lack of technology for processing of sub-grade ore concentrates and intermediate products for extraction of Zn, Pb, Cu and precious metals at the metallurgical stage was a constraint for an increase in the production of these metals. The technology developed in the Gintsvetmet Institute is based on an improved electrothermal smelting process for treating calcined charge, ensuring thereby a reduction in power requirement and improving the environmental performance of the process. Electric smelting of sub-grade polymetallic concentrates produces lead bullion, to which the bulk of gold and silver reports, as well as well segregated matte and slag concentrating the bulk of zinc. Lead bullion and matte are commercial-grade products; zinc is recovered from high-grade (15% Zn) slag by slag fuming process. Reduced loss of precious metals in slag ensured by the given technology is attributed to the fact that the slag contacts with matte with low contents of gold, silver and lead, rather than with lead bullion. Limited amounts of off-gas typical of electrothermal processes ensure cost-effective operation of dust recovery devices and a reduction in emissions of harmful pollutants into the ambient air.

Jan 1, 2002

By J. Wendt, P. R. Sahm, T. Uloth, M. Weck, F. Foertsch

"The FEM program systems CASTS (Computer Aided Solidification TechnologieS) (1) and FINELF (FINite ELement Frontal Solver) are used to optimize a thin walled die casting. After a short description of the programs it will be worked out how to use them not only for simulating solidification processes but also for optimizing the design of workpieces. The calculations will be done for an automobile's support bracket which is manufactured in a well known car factory in Stuttgart, FRG.IntroductionAt the Aachen Foundry Institute the software package CASTS was developped to simulate solidification of castings. In order to optimize the whole manufacturing process it does not appear sufficient any more to take into account only the specific aspects of casting. For instance one has to consider additionally the stress situation under service load. For this reason the Foundry Institute together with the Aachen WZL-Institute (Machine Tool Laboratory) and the car factory mentioned above started to probe into a first step in that direction. Figure 1 shows the support bracket which shall be optimized."

Jan 1, 1986