Search Documents

By Jorge Gibson, P. Chris Pistorius, Megha Jampani

"The main reason for the significant carbon intensity of integrated steelmaking (approximately 1.8 tons of CO2 per ton of steel) is the use of carbon-based reductants in blast furnace ironmaking. Several changes to blast furnace ironmaking have been proposed as ways to reduce carbon intensity and cost. A conceptually simple two-zone blast furnace mass and energy balance can be used to quantify the expected impact of such process changes on coke rate, carbon intensity, and productivity. Examples to be discussed include top gas recycling, combining lower blast temperatures with increased coal injection to produce a rich top gas, using prereduced feed, and tuyère injection of natural gas. The use of the operating window – which illustrates how allowable flame temperatures and top-gas temperatures constrain feasible oxygen enrichment levels – is illustrated. Increased use of natural gas would lower the carbon intensity of blast furnace ironmaking.IntroductionBecause of the significant carbon intensity of steelmaking (approximately 1.8 tons of CO2 emitted per ton of steel produced) and the high production rate of steel (more than 1.4 billion tonnes per annum), steelmaking is responsible for a large percentage, approximately 6.7%, of world anthropogenic CO2 emissions [1]. By far the largest input of the carbon into conventional steelmaking is as coke, which is essential to blast furnace ironmaking. A typical fuel rate for blast furnace ironmaking is 450 kg of fuel per tonne of hot metal (THM). (""Fuel"" includes coke and injectants which partially replace coke; pulverized coal and natural gas are typical injectants.) Assuming the fuels to contain 90% carbon on average, and since nearly all of this carbon exits the steel plant as CO2, a fuel rate of 450 kg is equivalent to a CO2 intensity of 1485 kg/THM – by far the largest part of the total CO2 intensity of steelmaking.Blast furnace ironmaking is expected to remain the main source of new iron units; this paper gives some estimates of the extents to which further reductions in carbon intensity from blast furnace ironmaking is possible. A recent European assessment suggested that blast furnace process intensification options such as increased pulverized-coal injection or natural gas injection would yield only modest energy savings [2]. However, if the focus is on CO2 emissions rather than on total energy use, there would be an advantage to using fuels – such as natural gas – which have lower carbon contents relative to energy content."

Jan 1, 2014

By Zviad Kovziridze

Structure of celsian ceramics in BaO-Al2O3-SiO2system is studied with electron microscope in the entire temperature region of baking interval. The process of the pores filling and the full consolidation of material growth at comparatively high temperatures of baking intervals are described.

Jan 1, 2006

By Yinlun Huang, Cristina Piluso

"Industrial sustainability looks to improve material and energy efficiencies, product quality and variety, and productivity within an industrial zone, thus pursuing the long-term sustainable development of the region. This paper introduces a systems-based modeling methodology, which provides industrial leaders with the ability to evaluate future production options to determine the path with the highest positive impact on both their own sustainability and the sustainability of the overall industrial zone. A comprehensive study on sustainable development of an auto-manufacturing focused industrial zone under uncertainty is illustrated. Introduction Sustainable development refers to a continuous process of improvements that must be followed in order to achieve a state of sustainability. In its most general form, a widely accepted definition of sustainable development was identified in the Brundtland Report as “development that meets the needs of the present without compromising the ability of future generations to meet their own needs” [1]. Sustainability will occur when the material and social conditions can be maintained or improved for human health and the environment over time without exceeding the ecological capabilities that support them [2]. An industrial zone is defined as a geographic area comprised of a network of industrial sectors, each composed of a number of entities. Such a zone is highly integrated and complex, and contains numerous uncertainties due to each industry’s extreme dependencies on its suppliers and customers throughout the product supply chain. In the context of an industrial zone, sustainable development refers to the continuous process of advancements in the zone, and the entities that comprise it, creating more value, wealth, and profits (economically viable dimension), providing environmentally benign products with less raw material consumption and waste generation (environmentally compatible dimension), and collaboration and a direct relationship among all involved in the supply chain, i.e. the corporations, employees, suppliers, investors, communities, customers, etc. (socially responsible dimension). These are the triple bottom lines of industrial sustainability. In order for economic, environmental, and social sustainability improvements to be successfully implemented within an industrial zone, the industrial decision makers must possess system-wide analysis abilities. The analysis of the sustainable development of an industrial zone involves decisions at the local, regional, or national levels, which are complex and involves handling of ill-defined parameters with a high degree of uncertainty due to the imperfect understanding of the underlying issues [3]. This work focuses strictly on the uncertainties in future zone planning and a method and a scenario based approach that can be used to evaluate the sustainable development of an industrial zone among these uncertainties."

Jan 1, 2008

The reported values of the standard reduction potentials of the Au(NH3)2+/Au(0) and Au(S2O3)23-/Au(0) couples are reviewed to emphasise the experimental difficulties associated with the measurement of reliable values for these quantities. The standard reduction potential for Ag(I)/Ag(0) in ammonia and thiosulphate solutions measured at ionic strength 0.1 and 25oCis used to predict the following relevant stability constants () for gold complexes based on the linear free energy correlations: Au(NH3)2+2 = 1013, Au(S2O3)23-2 = 1024 and Au(NH3)43+4 = 1033. The equilibrium constant ( 10-11) for the reaction Au(S2O3)23- + 2NH3 = Au(NH3)2+ + 2S2O32- based on these stability constants is in reasonable agreement with the measured value (10-9) based on potentiometric and spectroscopic data when excess ammonia was added to a solution of Na3Au(S2O3)2. This also indicates that the stability constant of Au(NH3)2+ is 9 to11 orders of magnitude less than that of Au(S2O3)23-. Relevant species distribution and Eh-pH diagrams based on the revised data are presented.

Jan 1, 2003

By E. A. Trillo, L. E. Murr, R. D. Flores, J. C. McClure, B. M. Nowak

Complex vortex and swirl-like solid-state flow phenomena have been observed in the residual microstructures characterizing the friction-stir welding (FSW) of copper to 6061 aluminum; 2024 aluminum to 6061aluminum,2024 aluminum to 1100 aluminum, 2024 aluminum to 7039 aluminum and 2024 aluminum to 2195 aluminum. These flow phenomena are characterized by intercalation lamellae composed of dynamically recrystallized grain structures of the dissimilar metals which provide a super-plastic-like mechanism for the FSW flow in the solid state; there is no melting and temperatures at the weld center do not exceed about 0.8 TM (where TM is the absolute melting temperature (K)). In experiments to be described and illustrated, optical or light metallography (LM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques are utilized in examining residual FSW microstructures corresponding to tool rotation (stirring) speeds ranging from 400 to 1200 rpm, and traverse (or actual welding) speeds of 1 to 2 mrn/s.

Jan 1, 1999

By T. S. Bannos

Section 1417 of the Safe Drinking Water Act Amendments enacted by the O.S. Congress prohibits the use of lead containing solders for potable water systems in new construction or when making repairs. The legislature defines "lead-free" solder as containing less than 0.2% lead. In the development of a new solder it was recognized in addition to the lead free requirement, the alloy should perform as well as the popular 50/50 tin lead solder, both in application and properties. Another objective was to have only nontoxic elements. This led to the development of a 4.0% copper, 0.5% silver and 95.5% tin solder. Review of the merits of other alloy systems and the development of the physical properties along with test data are presented for the lead free tin. rich alloy.

Jan 1, 1990

By Fathi Habashi

The behavior of pyrite, covellite, and arsenopyrite during leaching is different from other sulfides due to the presence of the disulfide ion, Sl. Arsenopyrite contains in addition, the diarsenide ion, Asl. The disulfide ion undergoes auto-oxidation in high acidity leading to elemental sulfur and sulfide ion formation: The sulfide ion may oxidize further by oxygen to elemental sulfur if high acidity is maintained. In neutral medium, the disulfide ion does not undergo auto-oxidation but oxidizes to thiosulfate then to sulfate: This leads to the two overall reactions observed experimentally: In acid medium and in neutral medium Covellite and arsenopyrite behave similarly.

Jan 1, 1995

By Vahid Rastegar

"Characterization of the microstructure and revealing dendrites in the microstructure and also measuring the dendrites arm spacing and the distribution of silicon were studied in various pieces of compacted graphite cast irons with 0.17, 0.185, 0.2, 0.22 and 0.24 percent of mischmetal. Black-white and color metallography (quantitative and qualitative) were carried out on the various steps of the cast samples. Distribution of silicon was studied quantitatively using spot analysis with scanning electron microscopy. Furthermore, effects of two variables (cooling rate and mischmetal percentage) on dendrites arm spacing were investigated.In order to color metallography, the samples were plunged into a boiling solution of 18% KOH, 9% NaOH and 9% picric acid in distilled water. It was inferred that the microstructure coloration varies according to the sequence: green-->red-->yellow-->blue-->dark brown->light brown as the silicon content decreases. After observing dendrites, dendrites arm spacing was measured. In this method, it seems to be possible to predict the mechanical properties of compacted graphite cast irons by knowing dendrites arm spacing and without any destructive testing. After studying the two variables, it was concluded that dendrites arm spacing decreases as the amount of mischmetal increases and it increases as the cooling rate increases.IntroductionIn general, detecting of primary austenite dendrites is not possible in cast irons due to their solidification system. Observing the dendrites in the room temperature is possible only in those gray cast irons that contain type D graphite. With collecting data of dendrites arm spacing (DAS) measurements, it could be possible to achieve the mechanical properties of cast irons without any destructive testing. In this research by applying a particular method, primary austenite dendrites and also distribution of silicon in the microstructure has been observed."

Jan 1, 2012

By Michael E. Stout

The recovery of the constituent components of spent lead acid batteries was pioneered in the early 1970's by M.A. Industries, Inc. MA's main reason for research and development in this area was to recover the polypropylene casings for use as feed stock in their injection molding plants. At that time spent and reject casings were either disposed of or being fed with the lead 'bearing materials into the ,smelting process. M.A. has since developed, built and operated plant for the conversion of scrap casing into reusable copolymer resins. The system is composed, of washing, .sizing, extrusion and pelletizing the polymer into a form which is ready to be injection molded into new products.

Jan 1, 1995

By Mikiya Tanaka, Mikio Kobayashi, Kazuya Koyama, Yoshihiro Nishisu

Preparation of multicomponent powders are very useful and important for producing the materials with complicated and homogeneous structure. Therefore multicomponent powders have a lot of attention in the field of advanced value-added materials. The aqueous processing in hydrometallurgy has a broad potential for producing multicomponent homogeneous precipitates. Furthermore the aqueous processing has a future potential for integrating the separation, precipitation and synthesis processes. In this presentation the precipitation from homogeneous solution including rare-earths and/or common metals is presented. These precipitates probably consist of almost monodispersed, multicomponent and spherical particles by precisely controlling several reaction factors, reaction temperature, concentrations of starting materials, pH and so on. The separation of the nucleation stage and the growth stage of the particles is very important and how to control the reaction factors to realize enough separation is discussed. In this presentation the systems of Y-Eu-0, Y-Fe-0 and Y-Al-0 are mainly presented. In addition the precipitation-stripping method from organic phase is presented focusing the synthesis of multicomponent powders of Ni-La-0 system. These precipitates have multicomponents homogeneously and so they are converted to multicomponent ceramic powders by calcination. They are important compounds as phosphor, opto-magnetic materials, optical materials, hydrogen storage alloy or as the related precursors. In this presentation some characterization of these particulate materials is included.

Jan 1, 1998

By Brent W. Madsen

The acid-ferric sulfate leaching of low-grade sulfide copper mine waste provides more than 10 percent of the U.S. supply of new copper, but recoveries and leaching rates are very low. In Federal Bureau of Mines research to improve the leaching process, experiments on 5- to 10-ton lots of mine-run ore were more revealing than bench-scale tests on fine ore. This report discusses the results obtained by leaching run-of-mine and minus 6-inch plus 112-inch samples of low-grade chalcocite-bearing mine waste. The samples were leached for 461 days and 61.6 and 37.7 percent of the copper was extracted from the minus 6-inch plus -112-inch and run-of- mine samples, respectively. A mixed kinetics model was applied successfully to the leaching of the sample with the fines removed where bulk solution transport was not rate controlling. The model, when applied to the run-of- mine ore, gave somewhat higher predicted copper extractions than experimentally determined. Subsequently, oxygen was introduced into the run-of- mine ore, leaching continued for an additional 312 days, and an additional 53.0 percent of the copper was extracted. Before the leaching experiment was dismantled and the residue sampled, the ore was treated with sulfur dioxide and its permeability was improved markedly. The results of each of these procedures are interpreted in relation to the attendant condition of the test.

Jan 1, 1976

By R. Moreau, V. Uspenski, K. Messadek, Y. Delannoy

Experiments and numerical simulations have been carried out to investigate the properties of quasi-2D turbulence. A new mercury model experiment has been built and tested in a uniform magnetic field up to 6T, (Ha~ 1000), ensuring a better two-dimensional behaviour than earlier versions (Alboussiere et al., 1997), limited to 0.2T. The quality of the experimental results has been improved in order to get wave number spectra (instead of frequency spectra) and higher signal over noise ratio (due to the higher magnetic fields). In parallel, some two-dimensional "direct" numerical simulations were performed using a commercially available code to solve a 2-D motion equation involving a source term to model the Hartmann layer. This term is derived from the condition of closure of the electric current, which allows to transfer the Hartmann effect into the 2D-core flow without simulating the layer itself (Sommeria & Moreau, 1982). No subgrid scale modelling is needed in such a two-dimensional situation where most of the energy is carried by the large scales.

Jan 1, 1999

By Mahmood Alemrajabi

When LKAB processes their iron ores in northern Sweden, they generate apatite as a by-product. The apatite has been recovered by flotation and the concentrate contains about 0.4 wt% rare earth elements (REE). Both phosphate rock and REE are listed as critical raw materials for the European union. In the present study, the recovery of REE within the nitrophosphate process of fertilizer production has been studied. In the first stage, the REE are precipitated and isolated as a phosphate concentrate. For further purification and individual separation of REE by solvent extraction, removal of phosphorous from the concentrate to enhance the dissolution of REE in mild acidic solutions is essential. In this study, thermal treatment of the concentrate with sodium hydroxide at elevated temperatures followed by water leaching has been studied in order to separate the phosphorous and thereby facilitate dissolution of the REE. The results show that 95% of total phosphorous initially present in the REE phosphate concentrate is removed after thermal treatment with NaOH 1:1 mass ratio, at 400 °C.

By S. Moussa

The formation of boron-doped nickel aluminides Ni3AI, (76 at. % Ni) from elemental powders by reaction synthesis using reactive sintering was studied. The process involves the mixing of elemental powders of nickel and aluminium with various wt % of boron up to 1 wt % boron. Nickel and Aluminium powders were mixed in the correct proportion to form the intended boron-doped nickel aluminide intermetallic. XRD, SEMI EDS, Image analysis and Archimedes principle; were used to study the effect of Boron addition on the final microstructure, bulk density, average grain size of as reactively-sintered nickel aluminides (boron-doped), compared with no boron addition. The results showed that at greater boron content than 0.3 wt %, a two-phase non-equilibrium microstructure of consisting of NiAI phase in NiJAI matrix was formed that have been primarily retained even after heat treatment for 5 hours at 1000 °C. Boron was present in solid-solution within both the NiAI and the Ni3AI (in greater amounts) phases.

Jan 1, 2001

By J. Chen Kuriyama

One method to store hydrogen effectively involves the use of metal complexes such as the alkali-element aluminum hydrides. The hydriding/dehydriding properties of these materials depend on how to prepare them with different structures and microstructures. The present work focused on a high-energy ball milling technique to produce Ti-doped lithium tetrahydridoaluminate (LiA1H4) and lithium hexahydroalanate (Li3AIH6) powders with nanocrystallites. The phase structures and dehydriding/rehydriding characteristics were investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Brunauer-Emmett-Teller measurement, thermogravimetry, and differential scanning calorimetry. The mechanism of dehydrogenation and rehydrogenation was also examined by means of X-ray photoelectron spectroscopy (XPS). The results on the relation between the reversible hydrogen storage and catalysis function of the Ti-doped complex hydride indicate that both the homogenous distribution of Ti+AI nanoclusters and the Ti¬catalyst with Ti e> Ti3+ (Ti0/Ti2+/Ti3+) defect sites play important roles in optimizing the reversible hydrogen storage.

Jan 1, 2002

By Huaming Yang

Infrared materials are a special kind of material widely used in military, biological engineering and chemical industry. However, the problems associated with them such as unstable properties, high cost and a high thermal expansion coefficient seriously restrict the development and the wide application of the traditional infrared materials with the SiC or ZrSiO4 matrix. The ultrafine quartz powder is normally used to prepare the infrared materials by hot-pressing technology. The aim of the paper is to investigate the thermal expansivity, the effect of the SiO2 size and the addition of Al2O3 or Fe2O3 on the infrared emissivity of the quartz matrix of the infrared material (QMIM) in a 8-25um wavelength range. The results indicate that 89% of infrared emissivity and 0.4x 10-5/°C of thermal expansion coefficient of QMIM can be obtained. The affecting mechanism of A1203 and Fe2O3 on the infrared emissivity of QMIM were also discussed.

Jan 1, 2003

By Huaming Yang

Infrared materials are a special kind of material widely used in military, biological engineering and chemical industry. However, the problems associated with them such as unstable properties, high cost and a high thermal expansion coefficient seriously restrict the development and the wide application of the traditional infrared materials with the SiC or ZrSiO4 matrix. The ultrafine quartz powder is normally used to prepare the infrared materials by hot-pressing technology. The aim of the paper is to investigate the thermal expansivity, the effect of the SiO2 size and the addition of AI2O) or Fe2O3 on the infrared emissivity of the quartz matrix of the infrared material (QMIM) in a 8-25um wavelength range. The results indicate that 89% of infrared emissivity and 0.4x 10.5°C of thermal expansion coefficient of QMIM can be obtained. The affeeting mechanism of Al2O) and Fe2O3 on the infrared emissivity of QMIM were also discussed.

Jan 1, 2003

By Marcelo A. Martorano, Moyses L. Lima, João B. F. Neto

"Directional solidification is an essential refining step to obtain solar grade silicon from metallurgical silicon. This step can be carried out in a Bridgman furnace, where nearly constant temperature gradients and solidification velocities are imposed on the solid-liquid interface. In the present work, this directional solidification was conducted in a static furnace, in which large temperature gradients and low solidification velocities were enforced to increase macrosegregation. The resulting ingots were analyzed regarding their macrostructures, microstructures and chemical composition. Using measured cooling curves in the ingot as boundary conditions, a mathematical model based on the concept of a stagnant liquid layer at the solid-liquid interface was implemented to predict the macrosegregation profiles. The chemical analyses of the ingots show macrosegregation of several impurities to the ingots top. The mathematical model indicates that liquid convection plays an important role in stabilizing the planar solid-liquid interface, increasing the macrosegregation of impurities.IntroductionMost of silicon used for photovoltaic (PV) energy production is obtained by chemical processes, such as, Siemens and its derivations [1]. However, these chemical processes have drawbacks related to relatively high energy consumption and investment costs, and to safety and environmental problems. In order to overcome these difficulties and to fulfill the silicon demand for PV applications, several metallurgical routes are under development [2] to produce silicon of enough purity to PV applications (SoG-Si) from metallurgical grade silicon (MG-Si).Metallurgical routes involve different steps among which the directional solidification is pointed out as a fundamental one [1]. Directional solidification can cause macrosegregation of impurities to the last part of the ingot to solidify. The impurity segregation during solidification is related to the low solute partition coefficient (k0) between liquid and solid silicon. Most of the impurities in MG-Si have k0 << 1, except for boron, phosphorus and oxygen, which require specific steps of the metallurgical routes to be eliminated. The equilibrium partition coefficient and the solubility limits for the most important impurities in MG-Si are shown in table 1"

Jan 1, 2014

By Zhihe Dou, Zimu Zhang, Guozhi Lv, Yan Liu, Xiaoli Jiang

"Cyclic heat stewed slag washing water carries high content of alkali and calcium and may cause serious tube scaling and impose an adverse impact on normal production. This study proposes a solution to utilize washing water by absorbing and mineralizing CO2, potentially restraining scaling and being able to create calcium carbonate powders. Effects of water flux on water quality, utilization ratio of CO2 and yield of calcium carbonate powder have been investigated; meanwhile, features of calcium carbonate powder are also represented. On the other hand, effects of factors such as as injection flux, pressure of CO2 on utilization ratio of CO2, morphology and purity of calcium carbonate are also investigated. The results show unambiguously that after soften injection of CO2, calcium ions were removed effectively via precipitation, alleviating the scaling problem. High purity yet fine carbonate powder could be achieved.IntroductionNowadays, 0.34 tons of blast furnace slags will be produced when producing 1 ton of pig iron; ensuing that, 0.12 tons of steel slag will be generated with 1 ton steel production while 1.57 billion tons of steel output all over the world in the year of 2012. It is therefore a critical issue to realize zero discharge of steel slags to achieve sustainable development and cyclic economy of iron and steel industry. In recent years, research institute of MCC and China JINGYE engineering company developed a heat stewed steel slag self-decomposition technology GENERATION III to solve the problem of instability of steel slags and realize the zero discharge. However, the problem of circulation line scaling which may cause the clogging, even exploding, need to be solved. The principles of the technology are: directly spraying water to the high temperature steel slag when it is poured into the hot closed pot, realizing the selfdecomposition via utilizing the waste heat of steel slag. The washing water is recycled to achieve a cyclic utilization. The process is shown in Figure 1."

Jan 1, 2014

By V. Jiricny

The novel spouted-bed electrode (SBE) is a cathode system where copper is deposited at a high current density in a moving bed of copper particles. Preliminary results on the deposition of copper from acidic sulfate electrolytes using this novel cathode system were described during Copper &apos;95 conference. Despite a high current density, the electrical energy consumption was equal to or lower than that in the conventional electrowinning. The present paper describes more investigations on SBE. The SBE consists of copper particles with approximately 1 mm diameter onto which copper is deposited from acidic sulfate electrolyte whose composition is similar to conventional electrowinning. Three types of anodes were used in conjunction with the spouted-bed cathode, namely, DSA anode for oxygen evolution, and two novel anodes. One anode is less expensive than DSA; however it showed much promise in energy consumption. At a superficial current density of 2200 A/m2, the energy consumption was around 1.0 kWh/kg copper. The research activities described in this paper were supported by BHP Copper.

Jan 1, 1999