Search Documents

By Robert B. Haagensen

While light optical microscopy has long been employed by the mineral processing industry, there has been a tendency to shy away from its use for all but the most exacting purposes. Despite the usefulness of micros-copy in solving a wide variety of problems, the response to such work is often less than enthusiastic primarily due to time considerations. Microscopical techniques are therefore often relegated to the "ivory tower" and their direct and practical application to everyday problem solving over-looked. The purpose of this paper is to dispel such attitudes and promote a wider use of light microscopy. Several examples are given which point out the indispensib1e nature of optical microscopy as a rapid means of defining and solving problems in mineral processing. The application of other instrumental techniques to augment the information obtained is also discussed, particularly the value of the combined use of the optical microscope and electron probe micro-analyzer.

Jan 1, 1981

By Steven Wright

The extent and the rate of reduction of slags produced from the smelting of recycled lead batteries were investigated under laboratory conditions using graphite as reductant. Simultaneous reduction of PbO, Fe2O3, Sb2O3 and As2O3 occurred at temperatures of 1180 and 1200°C, with Sb and As reporting to the metal phase while the PbO content of the slag was above 2 wt%. Fuming of As from the metal occurred at lower concentrations of lead in the slag. Discard slags with low levels of As, Pb and Sb were produced. Arsenic levels were reduced to less than accurately measurable by ICP analysis, and Sb levels in the final slags were in the range of 0.1 to 0.2 wt%. The kinetic data obtained were analysed and compared with other measurements on lead oxide containing slags. The results showing a dependence of the reduction rate on the oxidation state and the basicity are consistent with other studies on well characterised industrial and. synthetic lead slags. These results indicate that when carbonaceous reductants are used, the rate of interfacial reactions play an important role in enabling the production of environmentally acceptable discard slags.

Jan 1, 1994

By Hiroyuki Sano, Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa, Shin-ya Iwahori

"Pyrometallurgical process using Cu2O-based slag was proposed as a recycling process for copper scrap. However, it is difficult to remove nickel from copper by oxidative refining. Therefore, it is necessary to reduce the concentration of nickel in copper before the oxidative refining. In the present work, the copper enrichment stage in this recycling process, where copper scrap melt is separated into the Fe-C-Cu melt and the molten copper, was taken up and the compositions of both melts were measured. Based on the above results, the distribution ratios of nickel between the Fe-C-Cu melt and the molten copper were calculated. Furthermore, the optimum condition of copper enrichment stage was discussed from the viewpoint of nickel removal and copper recovery. The possibility of recovering 4N-purity copper by using this recycling process was confirmed.IntroductionRecycling is well known as a method for saving resources and reducing environmental damage. More than 99% of copper is used in metallic form - as metal or copper alloys[l]. High-grade copper scrap is directly re-melted and reused, while low-grade copper scrap is transported to copper smelters to be pyrorefined and electrorefined. Nevertheless, a great amount of copper is being stockpiled in the cities and should be recycled in the near future. At that time, the current recycling process will face new problems due to the increases in the recycling rate to the smelters. This includes insufficient combustion heat to melt copper scrap and ·almost no benefit in electrorefining because the scrap does not contain gold and silver. Thus, an alternative pyrometallurgical method for copper scrap refining will be required."

Jan 1, 2000

By Kexin Jiao, Huichang Song, Zhijia Zhang, Jianliang Zhang, Zhengjian Liu

A clear understanding of iron carburization reaction occurring between molten iron and carbonaceous materials is of great importance in blast furnace, and it is one of the hot spots that ironmaking workers pay close attention to. Although carburization rates between iron and coke have been studied, the factors directly controlling it have not been clearly identified. This study focused on the kinetics analysis of iron carburization reaction. Sulfur content was determined as having positive influence on graphite carburizing reaction rate in the range of 0.02% - 0.06%. The values of apparent activation energy calculated by the experiment are consistent with the existing literature, which in turn proved the reliability of the experimental data.

Jan 1, 2015

By Fu-Shen Zhang, Mengjun Chen, Jianxin Zhu

"In China, hazardous e-waste—cathode ray tube (CRT) glass is usually left around, and it is likely to contact with water resources directly. To identify the real leaching characteristics and bioavailabilities of heavy metals Pb and Ba contained in CRT glass in the nature environment, experiments were carried out by simulating the nature environment. The results indicated that Pb and Ba contained in CRT glass were stable in most conditions, which only showed obvious leaching toxicities in strong acidic/alkali conditions. EDTA and DTPA extractable Pb and Ba amounts were extremely high, e.g., EDTA extractable Pb of color funnel glass was up to 1960.07 ìg/kg, indicating that the potential bioavailability of waste CRT glass is very high. IntroductionIn recent years, cathode ray tube (CRT) contained monitors or TV sets has been substituted by novel and better electronic and electric equipments such as LCD and PDP, leaving huge amounts of end-of-life CRTs. 50~85% of the total weight of a computer monitor or a TV set is glass'1-21, which was classified to three categories: black & white glass (BW), color panel glass (CP) and color funnel glass (CF), according to their chemical compositions'3' (Méar et ai, 2006). In order to provide shielding from X-rays generated during the picture projection process, lead, barium and strontium oxides were used in the glass. In general, a color CRT contains 1.6-3.2 kg of lead'4'. Concerning the high toxicity of lead, these waste glasses have posed a potential risk to the environment and human health and researches on these glasses have been attracting wide and tense attention currently."

Jan 1, 2011

By M. Arenas

A corrosion study of a bonded NdFeB permanent magnet materials alloyed with titanium carbide additions has been undertaken. The materials were produced by rapid solidification by melt spinning. Commercial epoxy was used as a bonding medium. The corrosion results were compared with those of a near stoichometric unalloyed NdFeB. Anodic polarization and potentiostatic techniques in 0.9 M Na2SO4 solutions were used to characterize corrosion behavior. It was found that the addition of 6 a10 Tic resulted in superior corrosion resistance, as indicated by lower corrosion currents and less iron dissolution at fixed potential.

Jan 1, 1997

By Takaaki Ishikawa

The distribution equilibria of lead, zinc and copper between CaO-Si02-Ah03 melts and liquid copper were measured at 1623K under a controlled H2-C02 atmosphere. The distribution ratios were plotted against the oxygen partial pressure, and reasonable oxide forms dissolved in the melts were estimated from the slopes of the plots. The activity coefficients of zinc oxide (ZnO), lead oxide (PbO) and cuprous oxide (CuO0.5) increased with increasing slag basicity, defined by XCao/Xsio2 The temperature dependence of the activity coefficients was also measured.

Jan 1, 2003

By John O. Burckle

For years, the measurement of fugitive emissions from the primary copper converter has defied all attempts based on inferential measurements, It has been concluded by virtually all investigators that the only dependable tech¬nique to measure these emissions would be to completely enclose an operating converter to permit the capture and measurement of all emissions. However, complete enclosure with a metal hood is difficult; many of the most serious fugitive emissions result during periods when the converter must be attended with crane-operated equipment. This approach would require either opening of the enclosure to permit the entry of large items of equipment or completely new methods for charging and tapping converters' The installation of the air curtain hooding system at ASARCO's Tacoma smelter has permitted a quantitative approach to the direct measurement of the fugitive for the first time. In this program, the fugitives captured by the air curtain were measured at a downstream sampling point in the exhaust side of the air curtain system during the various portions of the converter cycle. Emission factors were established for sulfur dioxide, filterable particulate (method 5), inhalable particulate, and selected trace elements.

Jan 1, 1983

By Baohua Li, Yanhui Liu, Shengping Li, Xuewei Lv, Yun Chen

There are almost ten billion tons of vanadium-bearing titanomagnetite in Panzhihua-Xichang area. However, iron ores in Hongge, which has the most abundant reserves in the four mine areas in Panzhihua, have not been utilized sufficiently so far. The reason behind this is the relatively high Cr2O3 in the ores (0.49 %~0.82 %), that due to its high melting temperature will negatively influence the blast furnace reduction and slagging process. Therefore, in the blast furnace process, Cr is hope to be reduced into molten iron, which can reduce slag viscosity problems. Slag iron reduction experiments were conducted to quantify the Cr reduction. Experimental results shows that with the increase of TiO2, the content of Cr in the hot metal is decreased when balanced. And during the initial stage of the reduction reaction, the reaction kinetic model is a first-order reaction.

Jan 1, 2016

By T. Mason, R. Macko

Electroless nickel (EN) coatings are widely used in the manufacture of automotive parts, providing uniform coating, corrosion protection, wear resistance and lubrication. In contrast to EN plating benefits, the disposal and treatment of waste solutions can cause many difficulties. The use of electrochemical treatment technology greatly improves _the operation of the main wastewater treatment process and reduces operation costs. A new, state-of-the-art job shop in the Chicago area, which provides EN plating for the automotive industry, has installed a large separated electrolytic cell for the treatment of spent EN solution (from dumps and wastewater). The waste/wastewater is handled by the separated electrolytic cell, batch treatment system, filter press and neutralization station. The implementation of modem electrolytic technology and auxilliary equipment provides an effective waste treatment process that meets environmental compliance criteria.

Jan 1, 2000

By Christina Viklund-White

Life Cycle Assessment has been used to compare the environmental performance of landfilling versus recycling of the zinc used for galvanizing steel. Hypothetical process routes were com-posed involving four different EAF dust treatment processes; Waelz kiln, DC-furnace, EZINEX and slag fuming, as well as scrap dezincing. The study shows that recycling of zinc used for galvanizing steel has environmental benefits in that it saves zinc resources. However, zinc recovery does not necessarily decrease the potential impact on global warming and acidification. The magnitude of these two impact categories is tightly correlated with the amount and type of primary energy consumed in a process. Due to the high electricity consumption in the dezincing process, this route has the highest impact on Global Warming Potential as well as Acidification Potential. The major part of the energy requirement for the production of zinc from primary and secondary sources is consumed in the reduction of ZnO to Zn. The consequence is that the theoretically possible savings in primary energy by recycling zinc-containing materials are relatively minor. The impact categories "land use" and "waste generation" are not considered in this study, but most likely the evaluation of such impacts would further increase the potential environmental impact of the landfill alternative. The results also show that the location of an electricity-intensive process highly affects the potential environmental impact. Comparing process and material alternatives in LCA studies where branch average data is used, is considerably more complex than when LCA is used within a company.

Jan 1, 2000

By Musa Karakus

Reflected light microscopic (RLM) examination of dust particles from lead and copper smelters can effectively characterize their mineralogy, texture, and origin. Scanning electron microscopic-energy dispersive spectroscopic (SEM-EDS) analysis provides confirmation of the optical identifications and chemical data on the phases. Studied lead smelter dust samples were from the: I) blast furnace, 2) sinter plant scrubber, 3) sinter plant crusher, 4) dross furnace, and 5) refinery. Phases identified included galena fragments, melted PbS, metallic Pb and Cu, Cu-Ni, Cu-Zn, Zn-Ag, Zn-Cu-Ag, Ni-Cu-Sb, and Ni-Cu-Zn-Ag metal alloys, Ni-sulfide, Cu-sulfide, and Cu-Pb-sulfide dross .phases; slag and sinter particles, coke fragments, unreacted original feed phases: pyrite, chalcopyrite, sphalerite, siegenite, bravoite; and oxidized particles: iss, bornite, chalcocite, covellite, magnetite, hematite, and goethite. Dust from a secondary copper refinery were found by RLM and SEM to consist of tenorite, cuprite, cassiterite, two silicate phases. Magnetite, hematite, Fe-Al-Cr-Mg spinel, periclase, forsterite, and wollastonite were derived from the furnace linings during initial cleaning.

Jan 1, 1992

By Sheng Dai, Yuan Lee, Haiming Xiao, J. P. Young

"There are numerous analytical applications of scatter-emission and/or absorption spectroscopy applied to liquids and solids in the temperature range of 0 to 350°C. In this paper an all-silica fiberoptic probe is described which is useful for spectral analyses from 0 to 1600 K and can be used in harsh chemical environments. The probe has been used for Raman spectral analyses of many molten salt and solid material systems to 1000°C. It has applications for such studies at higher temperature ranges. The instrumentation required along with the demonstrated and proposed applications of the all-silica probe are presented and discussed.IntroductionThere are many kinds of scatter-emission spectroscopies that are of value for analytical measurements. Fluorescence, reflectance, arc or spark emission are descriptors for some of these. Raman scatter spectroscopy is also quite a useful technique for analytical measurements.In Figure 1, we give a simplified explanation of the Raman effect. If one shines monochromatic light into a sample, light may be absorbed, exciting the sample to some virtual state. We know from experience that almost all of the light is re-emitted in the same wavelength range. This is called Rayleigh or Mei scattering and is designated in the figure by the arrows in both examples that point up and down from the same lower energy state. A very small percentage (the order of 10-4%) of the monochromatic light is re-emitted leaving the sample at a vibrationally-excited state. Thus, this light is at a distinctly lower energy compared to the exciting radiation. This is called a Stokes shift and is represented in the left-hand example by an arrow descending to a more energetic vibrational state. If the sample is not at a temperature of absolute zero, some of this vibrationally excited state will be thermally populated. That portion of the sample still absorbs and re-emits exciting radiation as Rayleigh scattered light, but a small percentage of the exciting light is re-emitted as the sample relaxes to the lower vibrational state. The energy of this light is of higher energy and is called an anti-Stokes shift, depicted in the example to the right. Notice that the energy separation of the Stokes or anti-Stokes shifted emission from that of the exciting radiation is the same, and expressed in ~cm-I. The intensity of either shifted emission is a function of the population of the vibrational energy states; therefore, the ratio of the intensity of Stokes to anti-Stokes signal varies with absolute temperature. We will come back to this point later."

Jan 1, 1997

By John E. Litz

The Denver Process is a chemical/metallurgical process for treating radioactive or mixed wastes by extraction and concentration of the radioactive and/or hazardous component(s). The process was developed at bench scale, evaluated at pilot scale, and will be implemented at full scale to remediate a low-level radioactive sludge. Six unit operations comprise the process: feed handling, leaching, solvent extraction, electrodeposition, precipitation, and tailing preparation. Unit operation design may be modified to tailor the process for varying feed stock composition. Radioactive or mixed waste is reacted with aggressive reagents in an aqueous phase, solubilizing targeted components. These components are then selectively extracted and concentrated in subsequent steps. Waste solids and solution exit the process as non-hazardous non¬radioactive waste. Dehydration of aqueous waste by submerged combustion eliminates aqueous discharge.

Jan 1, 1994

By P. R. Taylor

Diamond films have been successfully formed in an inductively coupled plasma (ICP) chemical vapor deposition (CVD) system from several gas mixtures: CH,-H,, C2112-112, and C2112-112-02' Our previous thermodynamic study indicated that the substrate temperature could be lowered by the presence of oxygen species at moderate system pressures (0.3-0.5 atm) and that higher volumetric growth rates required a high temperature source and a moderate pressure system in CVD processing. The principal experimental results were consistent with the thermodynamic predictions. The deposited films were characterized by laser Raman spectroscopy, scanning electron microscopy, and X-ray diffraction. The films were well faceted and uniform, with the growth rates over 10 pm/hr on molybdenum substrates. The crystal size ranged between 1 and 2 microns for a two hour experiment. It was possible to decrease the substrate temperature to below 800 °C in this system.

Jan 1, 1995

By C. Alexandru Sonoc

Donnan Dialysis uses ion exchange membranes to extract and separate cations. The driving force is provided by differences in chemical potential, rather than by electric fields or pressure. A Donnan Dialysis based process to recover lithium, nickel, cobalt, manganese, and organic acid lixiviant from recycled lithium ion battery cathodes is under development. In this paper we present a model of Donnan Dialysis and results of simulations of the aforementioned process. The simulations show that 170 m2 of membranes can process 1000 L of leachate ([Li+] = 0.285 M, [Co2+] = [Ni2+] = [Mn2+] = 0.095 M, pH 2) in two days and recover 94.1% of the lithium (as lithium carbonate), 99.4% of the transition metals (as mixed sulphates ready for solvent extraction), and all of the organic acid using 423 mol of H2SO4 and 268 mol of KHCO3.

By Bowen Li

Copper vermiculite is a special nanomaterial with excellent antibacterial and antifungal performance. By means of ion exchange, copper vermiculite containing up to 5.8wt% copper was prepared. The chemical and mineralogical characterization of the material was investigated in this study based on the XRD, AAS, TEM and EDS analysis, as well as the calculation of crystalline parameters and crystal chemical formula. Cu2+ and Mg2+ have similar atom radius and same electrovalence. Correspondingly, the structure character of copper vermiculite is very close to that of standard Mg-vermiculite. Most of the CU21 may have occupied the interlayer cationic positions in the form of hydrate in vermiculite. However, some may have entered into octahedral coordinate positions. The values of au and bo of the copper vermiculite crystal cell have no obvious change compared to that of original vermiculite micropowder, but the Co value decreased slightly, which is desirable for the stabilization of the Cu2+ in copper vermiculite.

Jan 1, 2003

By S. Rick Gilbert

In the course of producing a final metal product, smelters, refineries, and other metallurgical facilities produce wastes which often come under the ?scrutiny of Federal and state regulatory agencies. Many of these wastes contain combinations on zinc, copper, lead, cadmium, nickel or other metals. Frequently in the form of reverts, dusts, or sludges, these metal-containing wastes are often buried in a landfill or speculatively accumulated for future action. Environmental liability can be reduced in many cases by selecting,-a recycling facility which can re-process the waste for.' metal recovery. Encycle, at its hydrometallurgical facility Corpus Christi, has Successfully processed a variety of metallurgical by-products and wastes and returned those contained metals to commerce.

Jan 1, 1995

By Takaaki Ishikawa

The distribution equilibria of lead, zinc and copper between CaO-Si02-Ah03 melts and liquid copper were measured at 1623K under a controlled H2-C02 atmosphere. The distribution ratios were plotted against the oxygen partial pressure, and reasonable oxide forms dissolved in the melts were estimated from the slopes of the plots. The activity coefficients of zinc oxide (ZnO), lead oxide (PbO) and cuprous oxide (CuOQs) increased with increasing slag basicity, defined by Xcao /XSiO, The temperature dependence of the activity coefficients was also measured.

Jan 1, 2003

By Willy Persson

A common feature of the kinds and amounts of impurities present most pyrometallurgical, processes is injection of oxygen to, remove various in the feed. The degree of success of a specific process step relies critically on control of the instantaneous oxygen potential/oxidation stage, throughout the step as well as upon termination of the step. This will, for instance, determine the distribution of impurities between metal and slag. As long as the operation is perturbation free -detailed analysis of all additions and application of advanced models often yield satisfactory control means However, a pyrometallurgical process is seldom free from disturbances, which reduces the accuracy of the static models and leads to inconsistencies in scheduled route might be uncontrollable changes in quality and quantity of feed, operator interventions and shift changes, timing of cranes, lining wear and accretions etc. The implementation of dynamic, control to correct for disturbances and, more generally for process optimization, requires continuous on-line information on, the actual status of the process. The implementation of sensors for continuous process monitoring, e.g., as regards the instantaneously prevailing oxygen potential or oxidation stage, has been hampered by the highly aggressive environment in smelters; This is. where remote-sensing techniques based on optics and spectroscopy, have proven to form invaluable, tools towards the realization of dynamic production control. Since about 15 years Semtch has developed and industrialized a remote-sensing technology, based on ,optics and spectroscopy, for continuous on-line process monitoring and production control of various pyrometallurgical processes. The presentation will discuss applicability aspects with examples and experiences from installations and tests in ferrous and non-ferrous industry. Keywords: Applied spectroscopy, Metallurgy, Process monitoring, Production. Control

Jan 1, 2003