Search Documents

By Hamid R. Nikraz

This paper reports the finding of a comprehensive investigation carried out to evaluate the compaction characteristics of saturated sandstone aquifers in the Collie Coal Basin under conditions anticipated during dewatering operations. A triaxial technique has been adapted to evaluate the compaction characteristics of the sandstone aquifer in the Collie Basin. This technique, which allows the strata stress regime to be reproduced by triaxial loading with zero lateral strain, also provides a precise evaluation of lateral stresses and consequently Poisson's ratio under in situ conditions. The paper contains a description of the equipment commissioned, test techniques, results, analysis and interpretation of the data obtained. The testing evaluation techniques are general in nature and can be applied to field situations in locations where similar weak sandstones occur.

Jan 1, 1993

3-D finite element modeling was performed to study the effect of bedding plane sliding and separation and tensioned bolt in layered root It was found that the major influence zones of a tensioned bolt are restricted to the neighborhood of the anchor points; that bedding plane sliding and separation releases the vertical stress in the roof above entry but greatly increases the horizontal stress within the first layer of the roof, and that there is a triangular zone between the two adjacent bolts at and near the roofline level that is beyond the influence zone of the bolts which is liable to fail if conditions exist. Based on the results, three possible modes of roof failure are proposed for the design of tensioned bolting.

Jan 1, 2001

By P. K. Kaiser

The purpose of deformation monitoring for the evaluation of the stability of underground openings is reviewed briefly and some results from laboratory tests of small tunnels are presented. The ground behaviour is described by comparison with the response of structural systems and illustrated by the data from the testing of small tunnels. It is concluded that the main objective of a deformation monitoring system for stability evaluation is to determine the actual process of deformation and instability in the area surrounding the opening. Only when this process has been established is it possible to use deformation measurements to design support systems or to improve construction or mining procedures. Present monitoring practice is not sufficiently orientated toward the aim of process description.

Jan 1, 1981

By Winston Gale

This paper is presents a summary of recent investigations into fracture and caving about longwall panels. The results of these investigations indicate that rock failure initiates well ahead of the longwall face. Rock fracture typically forms in response failure through the material and bedding planes. Tensile fractures also form in massive units. These fracture patterns typically create a fracture network which determines the caving characteristics encountered at the faceline. The action of longwall face supports under such conditions is to maintain confinement to the fractured ground and develop a consistent caving line, The confinement developed above the canopy under these conditions can be variable on a shear by shear basis and the operational face support procedures play an important role in stability about the face area.

Jan 1, 2004

By David Bartsch

The Ohio Valley Coal Company (Ohio Valley) has operated the Powhatan No. 6 Mine in Belmont County, Ohio since 1972. Ohio University owns a 455-acre research farm over a portion of the Ohio Valley reserve containing 51 acres of old-growth forest known as Dysart Woods. In 1988, when Ohio Valley applied for a new mining area for its first longwall located several miles away from Dysart Woods, Ohio University claimed that mining at that distance would lower the regional water table and kill the old trees. In response, Ohio Valley began to study potential impacts from longwall mining on hydrology, soil moisture, and tree growth. Early studies examined the impacts of longwall mining on hydrology, soil moisture, and tree growth directly over mined areas compared to woodlots that were not undermined. A subsequent study examined tree-ring growth for a five-year period before and after longwall mining for several woodlots, some directly over panels and others at distances of up to 2000 ft away. No significant differences in growth rate associated with longwall mining were observed. New research was begun that compared longwall-mining impacts on groundwater hydrology, available soil moisture, and tree growth in two stands of mature trees located near Dysart Woods in order to confirm the earlier results. Using a test technique known as "Before-and-After-Controlled-Impact-Pairs," data was collected from one woodlot (test) that was undermined and from another (control) that was not undermined. Data collection began several years prior to longwall mining and has continued for several years after mining. The data for the test site shows that although the shallow and deep groundwater levels were affected by longwall mining, the soil moisture, vigor rating, or the growth rate of trees did not decline significantly compared to the control site where there were hydrologic impacts. The study shows that there are no known significant impacts to trees from longwall mining. The results of these studies were used by Ohio Valley to obtain State approval to longwall to within 300 ft of Dysart Woods

Jan 1, 2005

By Keith A. Heasley, Jian Yang

"LaModel uses a laminated overburden boundary-element model and can calculate not only seam-level stresses and displacements but also surface subsidence for thin tabular deposit such as coal seams (Heasley, 1998). Up to this point in time, the material property wizards in LaModel have primarily been designed for calculating accurate stress distributions in single- and multipleseam situations, and for investigating and optimizing pillar sizes and layouts in relation to overburden, abutment, and multipleseam stresses. However, the critical input parameters that will give the most accurate seam-level stress distribution do not necessarily produce the best surface subsidence prediction. The objective of this paper is to develop a methodology for calibrating the critical input parameters in LaModel to optimize surface subsidence prediction.For optimum surface subsidence prediction, it was found that the gob convergence (as defined by the final gob modulus) and the overburden stiffness (as defined by the lamination thickness) were the two most critical parameters that needed to be calibrated (Heasley, 2016). By calibrating numerous panels with various widths and depths, a formula that provides the optimum final gob modulus to use for subsidence prediction was developed. Also, three different empirical formulas for optimizing the lamination thickness as a function of overburden depth and/or the panel width to- depth ratio were determined for the three cases: supercritical panels, and subcritical panels with and without offsets. Further, if the user has measured data for subsidence factor and angle-of draw, the optimum final gob modulus and lamination thickness can be determined from the measured data. These new subsidence prediction formulas are being implemented into new material wizards in LaModel.INTRODUCTIONIn the past few decades, with the increased need for highly productive mining techniques, full extraction mining methods have been increasingly employed in the U.S. coal mining industry. These total extraction mining methods, which include both longwall mining and room-and-pillar retreat mining, normally cause immediate roof caving and the associated surface subsidence. These methods can be highly productive and cost-effective, but the associated surface subsidence can cause damage to surface structures and negatively impact the surface environment (Peng, 2008). Therefore, a reliable program for predicting the surface subsidence associated with full extraction mining is required for appropriately engineering and managing the surface subsidence impacts of full extraction mining."

Jan 1, 2016

By Weihua Song, Hongwei Zhang, Feng Zhu, Sheng Li, Guoshui Tang

"Rock burst is one of the most serious dynamic disasters in coal mining. Rock burst prevention involves two difficult tasks: systematically evaluating the occurrence conditions and effectively forecast for rock burst. This paper systematically studies the effects of natural geological dynamic conditions and mining engineering on and forecast for rock burst. It establishes the evaluation method and index system of rock burst geological dynamic conditions and proposes a method of forecasting rock bursts by monitoring fault activity with anchor cables. Natural geological dynamic conditions are a necessary condition while mining engineering is a sufficient condition for the occurrence of rock bursts. Rock bursts in mine must have suitable geological dynamic conditions, and mining engineering activity is merely an inducing factor. There is a good correlation between anchor cable stress variation and fault activity, when the anchor cable dynamometer indicates that the fault is active. It can forecast a rock burst a few days in advance. This technique has been successfully applied to Panel 83003 of a coal mine in China, which improved the safety production level of the mine and found a new way of rock burst evaluation and prediction.INTRODUCTIONRock burst is one of the most serious dynamic disasters in coal mining. With the increase of mining depth, rock burst disaster is becoming more and more serious. Systematically evaluation and effective forecasting of the occurrence of rock burst in the coal mines are important and difficult work in the control of rock bursts. Chinese researchers have performed numerous researches on rock bursts, Qi et al., established the rock burst model of frictional sliding instability, explained the occurrence mechanism of rock bursts by stick-slip phenomenon in frictional sliding, gave full consideration to the influence of primary rock stress and mining-induced stress on rock burst occurrence, and proposed the stress controlling theory of rock burst. Pan et al., [3] put forward the criterion of perturbation response, explained and analyzed the problem of rock burst in circular openings, put forward the ratio of coal-rock elastic modulus and reduced modulus is the significant parameters for the determination of stabilization; systematically summarized the rock burst distribution, type, mechanism and control in China. They classified rock bursts into three types: coal compression, roof fracture and fault movement. By applying energy transfer principle and conservation of energy, combined with the analysis of the weakening of rock fabric damage, Zhou and Jiang put forward the theory and equation for the occurrence of coal-rock mass impact effect. They analyzed and discussed the formation mechanism of rock burst by combining impact effect theory and energy equation. Wang et al., recognized that the mechanism of rock burst which induced by fault, fold and phase transition is the superposition of tectonic stress and mining stress and that the axes of syncline and anticline and their flanks are the location where rock bursts mostly occur. To prevent stress superposition is the efficient way to control the structural rock burst [7]. Jiang et al., summarized the research achievement of rock burst mechanism and controlling techniques and existing problems in recent years in China, and pointed out the direction to improve the level of prevention of controlling rock bursts in coal mines."

Jan 1, 2015

By J. D. Cole

In order to reduce the number of longwall face moves and to increase the rate of gateroad construction, super longwall panels, 1000 feet wide and 12000 to 14000 feet long, are planned for Wolf Creek Collieries No. 4 mine. The development of the longwall panels at the mine has evolved from 5-entry, to 4-entry, to 3-entry systems. A three-entry system including pillar size and entry supporting method for the super longwall panels was designed for long-term stability. The design procedures included field observation and studies, laboratory properties tests, in-situ stress measurement, and computer analysis. Three pillar design methods consisting of PILLAR, ALPS, and the Wilson Method, and one entry supporting method, ROOFBOLT, were adopted in this study. The procedures, methods, and results are discussed in detail.

Jan 1, 1990

By Erik C. Westman

The objective of this Bureau of Mines study is to determine the structural integrity and stress state of coal structure using seismic techniques. Bureau personnel conducted seismic transmission and refraction surveys on yield pillars and seismic tomography on rigid pillars. The pillars studied were in the headgate at increasing distances from the working face of a longwall coal mine, effectively evaluating pillars at lowering stress states and increasing levels of structural integrity. By examining characteristics of the seismic wave, including velocity and frequency, the survey results are used to infer yield zone thickness, core mss state, and stress distribution. An accurate definition of these parameters can not only provide mine engineers a useful tool for evaluating mine design, but also give valuable insight into the inherent safety of the mine structure.

Jan 1, 1993

By Ebrahim Ghasemi

Roof fall risk is a common problem in coal mines, and it is generally unpredictable due to variability in geological and mining parameters. In this study, a new fuzzy logic model was developed to predict roof fall rate in coal mines. Parameters such as coal mine roof rating (CMRR), primary roof support (PRSUP), intersection span, and depth of cover were considered as the model inputs. The model was developed based on experts? knowledge and also a database including about 109 datasets of roof performance from U.S. coal mines. Approximately 20% of these datasets were used to assess the performance of the fuzzy model. In each case, comparison between results from model and real roof fall rate showed that this model can predict roof fall rate to an acceptable extent.

Jan 1, 2011

By Stephen C. Tadolini

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that arc easy to handle/install under temporary or previously supported roof.

Jan 1, 2001

By D. G. Lynch, M. R. Martin, R. J. Coutts

"Broadmeadow Mine is an underground longwall mine located in Central Queensland, Australia. The mine introduced a top coal caving (TCC) longwall face in 2013 but since then has experienced severe convergence events at the start of each panel after 60–70m of retreat, resulting in equipment damage and the longwall almost becoming iron bound. A significant geotechnical monitoring effort during LW10 and LW11 to characterise the caving mechanics and operational changes during LW11 were successful in mitigating the risk posed by these initial convergence events. This paper describes the geotechnical monitoring programme undertaken during LW11, the operational methods used to mitigate these initial convergence events, and the contribution to these events of the TCC technique.A thick sandstone unit close to the extraction roof was likely the cause of the convergence events at the start of each longwall panel. However, stress change monitoring cells, surface extensometers, an inclinometer, and the blockage of holes designed for pre-conditioning using hydraulic fracturing indicated that the convergence events were not caused by the sudden collapse of sandstone bridging across the goaf. Rather, they were caused by the propping action of strong units within the overburden strata. Equipment design modifications were made to allow the longwall to remain operational during the convergence events and an operational strategy was implemented to mitigate convergence in LW11. The initial convergence event was successfully negotiated, and Broadmeadow went on to be the highest producing longwall for CY16 in Australia.INTRODUCTIONBroadmeadow Mine is an underground longwall mine located in Central Queensland, Australia, owned and operated by BHP Mitsubishi Alliance (BMA). The mine is a punch longwall mine using open cut pit access provided by Goonyella/Riverside Mine. Broadmeadow commenced longwall operations in 2005 using a conventional high reach longwall, but later changed to the top coal caving (TCC) method of extraction. Broadmeadow extracts the easterly dipping 5.5–7.5m-thick Goonyella Middle Seam in ranging in depth from 90m to 330m. The coal is washed and blended at the adjacent Goonyella/Riverside open cut mine to produce a premium coking coal product for export."

Jan 1, 2018

By Thomas M. Barczak

Wood cribs are used extensively to stabilize mine openings by providing resistance to deflections of the immediate roof and floor and by supporting the weight of unstable rock masses. While the unit costs of these supports are relatively low, their extensive use results in significant costs to coal mining. The Bureau of Mines has developed a model that computes the load capacity of wood cribs as a function of the displacement of the crib structure induced by mine roof and floor convergence. This permits comparison of the loading characteristics of various crib constructions and enables systems to be designed with consideration of the load conditions imposed by the mine environment. The design method matches the stiffness, strength, and stability of the crib structure with expected rock mass behavior to determine a crib design and employment spacing that will provide the lowest cost support.

Jan 1, 1993

By David Hill

Over the last decade, Beltana No.1 Mine has generally been Australia?s most productive longwall operation, with a ROM output of 7.2 Mt in YEJ2007. Characteristically favorable roof conditions and low depths of cover resulted in typically high rates of development drivage and longwall retreat. As a consequence of these high rates of development and extraction, there was a continuing focus on recovering and relocating the longwall face as efficiently as possible to minimize associated production delays and operational costs. This paper presents a comprehensive case study of the conventional longwall recoveries (?take-offs?) at the mine, from Longwall 1 to 14. By examining the take-off monitoring data collected over the life of the mine, the key geotechnical issues are demonstrated, including their relationship to the ground behavior experienced and the issues overcome.

Jan 1, 2011

By Zhanjing Yu

In this paper, an equation is developed to characterize the relationship between the UBC and plate size using a boundary integral approach. The equation was validated by the results from mo& than seventy (70) plate loading tests of different sizes conducted in various underground coal mines throughout the Illinois Coal Basin. The equation indicates that the UBC decreases as the plate size increases. The fundamental solution for this boundary integral problems is the Boussinesq equation. The load exerted by the plate on the floor surface is assumed to be uniformly distributed. Both normal and tangential loads are considered. It is also assumed that the floor fails in shear in a plate loading test. The equation may provide the mine operators with a useful tool to obtain from a plate load test of any plate size the UBC value required by the regulations.

Jan 1, 1993

By Kot F. v. Unrug

The depletion of thicker coal reserves has resulted in the thinner seams being economically attractive. Surface protection against subsidence limits the extraction ratio to 50% for the room and pillar method as a "no subsidence condition". That rule was developed for pillars with smaller width/height ratio because seams mined at the time were commonly 6 feet thick. Over time pillar ribs deteriorate around the pillar perimeter and thus decrease the area of the pillar. Using 50% extraction as the no subsidence condition in the squat pillar category (below 42 in with w/h > 7) causes unnecessary losses of reserves because squat pillars are stronger. In this paper a method is presented for design of long-term pillars. Based on the analysis of pillar deterioration and field observations, an increase of the "no subsidence" extraction rate to 60% for squat pillars is proposed.

Jan 1, 2001

By Paul Hagan

A diverse range of rockbolt designs and resin anchors are available for use in underground mines. Despite their wide spread use, the factors that affect the performance a rockbolt is not fully understood. The laboratory-scale rockbolt test facility at the UNSW Mining Research Centre is being used to gain a better understanding of the behaviour of rockbolts leading to an improvement in ground support. A test program investigated the nature of load transfer between a fully encapsulated rockbolt and the surrounding rock mass. It was found that with all other factors held constant, there were differences in the behaviour of load transfer depending on the method of loading. The typical pull-out arrangement as used in most field test work resulted in a different load transfer function to that observed when the load on the rockbolt was induced through bed separation.

Jan 1, 2004

By Syd Peng

In designing a proper roof support system, one must know the features of roof geology in advance of mining. The drilling parameters obtained during normal roof bolt installation cycle can provide a large amount of information on the roof geology when properly interpreted. It is also an economic way for identifying the geological features of the roof. This research develops a method for predicting the roof geology based on the drilling parameters obtained during roof bolting operation. From the results of a series of laboratory and underground tests, feed pressure is found to be a good indicator for identifying the voids/fractures and estimating the roof rock strength. This paper describes the method for determining quantitatively the location and the size of void/fracture and estimating the roof rock strength from the drilling parameters of roof bolter.

Jan 1, 2005

By Selmar A. Oliveira

"Safe mine closure is an important step in the mining lifecycle. Plans for safe and efficient closure should begin at the inception of mining. Ideally, closure occurs when the reserve has been depleted. However, when the abandonment of a mine occurs prior to the depletion of the reserve, several problems arise which need to be treated. This situation occurred at Verdinho Mine, located in the state of Santa Catarina, southern Brazil. Verdinho Mine is a coal mine that operated for more than 40 years without had backfill technologies applied. Soon before the exhaustion of the reserves, it was abandoned by the owners without proper closure. As a result, the Federal Public Ministry filed a public civil action to promote proper closure. Several parties are currently involved, including the National Department of Mineral Production (DNPM), the mining regulator of the Brazilian Government. To meet the judicial determination, a cooperation agreement was initiated between DNPM and the Federal University of Rio Grande do Sul (UFRGS) to identify and to monitor parameters which could result hazard due flooding mine, to model the various conditions to minimize the impact of flooding caused by total abandonment. Many processes must be planned and planned early in mining operations, and these processes must be performed over the life of the mine. Financial resources must be guaranteed by a specific fund fueled by operating revenues. When these resources are not properly employed, costs and technical difficulties prevent proper closure progress. If the removal of subsoil equipment, treatment and control of groundwater, regeneration of the surface, and closure of openings are not done correctly, there can be environmental, social, and stability impacts over time. To avoid this in the future, a detailed study is being performed at the Verdinho Underground Coal Mine on how to appropriately implement mine closure and monitoring procedures. This study is being conducted in response to a lawsuit filed by the Federal Public Prosecutor’s Office. INTRODUCTION The nature of the Mining Industry is such that all mining is a temporary activity, where the operational life of a mine is defined by the final project scope. The operating life of a mine lasts from a few years to several decades. Mine closures occur once the mineral resource at a working mine is exhausted, or operations are no longer profitable. Mine closure plans are required by most regulatory agencies worldwide, such as the Mineral Production National Department (DNPM) in Brazil."

Jan 1, 2017

By Q. F. Wang

Spontaneous combustion hazard of loose coal in the top-coal caving region of entry affects the safety of the entry and top- caving longwall face seriously. In this paper, by combining on- site temperature tests with lab tests and numerical simulation, the characteristics of microcirculation close to the top-coal caving region are analyzed. A model for the temperature fields of the microcirculation in loose coal is presented. Based on this model, the temperature distribution and possible self-ignition region can be predicted. Further, the heat and mass transfers in microcirculation are studied. Finally, the mechanism of oxygenation during the spontaneous combustion of microcirculation in loose coal of the top-coal caving region of entries is put forward. The research results in this papa may provide ideas for the prevention and putting out of the fire caused by spontaneous combustion in the caving zone.

Jan 1, 2004