Search Documents

By M. Javier

Defining the concept of sustainability is an important step for industry and society. It is necessary in order to clarify what it means when debunking the many misinterpretations pervasive in different levels of anthropogenic activities. Essentially, the extractive industry has a harvest of differences. Mining involves the extraction of natural resources which are finite, exhaustible, non-renewable, unsustainable, and pay only once. It is remarkable that the definition of sustainability that we will shortly arrive at has totally different characteristics from the definition accepted throughout society. We categorize nature as having its own destiny which is controlled by its own rules and principles and its own society, and is part of nature; therefore, society depends on nature and not vice versa as the initial focus. To society there are no conditions to humanize nature but only respect nature?s rules. It was a challenge to find simplicity for this task not only for the definition but also for the explanation of this concept specifically, to answer the question, ?what is the true meaning of sustainability?? Finally, we are also able through this definition to provide fuel for wide discussions and stimulate critical thinking to improve such a concept. As a result, we present this definition as the tool for society today and for future generations.

Jan 1, 2012

By Robert J. F. Goodfellow, William A. T. Meakin, Kevin Clarke, Eric Cole

INTRODUCTION New York City Water Supply—Background and History Since the 1840s New York City has been developing the largest, and perhaps, the best urban water supply and distribution system in the world in terms of quality and reliability. One of the engineering marvels of the modern world, the New York City water supply and distribution system serves a population of almost nine million, including residents in nearby Westchester, Putnam, Ulster, and Orange Counties of New York State. The average daily supplies presently are running at almost 60 m3/sec(about 1,350 million gallons per day). The watershed for the New York City water supply system, under the jurisdiction of the New York City Department of Environmental Protection (NYCDEP), consists of19 reservoirs and three controlled lakes, and covers an area of approximately5,000 square kilometers (about 2,000 square miles) north of New York City. The watershed total available storage capacity is about two billion cubic meters (560 billion gallons) and is divided into three reservoir systems: the Catskill and Delaware watersheds located West of the Hudson River; and the Croton watershed, located east of the Hudson River, see Figure 1. The first element of the system, the Croton Aqueduct, started operations in 1842.Through several updates and expansions, the present-day Croton system was in place by 1911, providing a potential maximum supply of about 15 m3/s (about 340 mgd). The system includes ten reservoirs and three controlled lakes. In the late 1800s, with the tremendous growth of the City, New York City water engineers began to look for additional sources. Between 1907 and 1929, the City acquired water rights and constructed a new 148 km (92 miles) Catskill aqueduct to convey water from the Ashokan Reservoir to the City. The Catskill system also included the construction of the Kensico and Hillview Reservoirs just north of the City,

Jan 1, 2005

By N. Aouad

The deployment of large machinery for low cost, bulk surface mine production operations has resulted in high-impact shovel loading operations (HISLO). In extreme cases, shovels load large dump trucks with 100-ton (or more) passes generating high-impact forces under gravity. HISLO generates high-frequency shockwaves that cause severe truck vibrations exposing operators to whole body vibrations (WBV). Current research study in this area has established that the vibration levels affecting the operator?s seat, lower-back, lumbar and cervical regions fall within the extremely uncomfortable zone compared to the ISO 2631 comfort zone. These results pose health threats to truck operators over long-term exposure to these vibrations. In this paper, the authors will examine engineered solutions to mitigate these health threats.

Jan 1, 2011

By S. Ersayin

In 1998, the Concentrator Modeling Center was established within the Coleraine Minerals Research Lab, Coleraine, Minnesota, to develop models for simulation of iron ore processing plants, and to assist plant operators in improving performance of their aging plants. The short-term objective was to develop necessary models for reliable simulation using conventional techniques, while the long-term objective was set as liberation-based modeling and simulation of these plants. The short-term objective was achieved in 2002 after the development of models for magnetic separators, hydro-separators and fine screens. A project funded by the U.S. Department of Energy was carried out to demonstrate the capability in improving iron ore processing at the Minorca plant. As a result of this study, a 10% improvement in throughput at the plant was obtained, and simulation became a desired tool for plant operators. A significant step in the long-term objective was reached in 2005 with the development of a liberation model. This was followed by incorporation of models capable of processing liberation data into the software. By early 2007, the Concentrator Modeling Center had the capability of performing liberation-based simulation of entire plants.

Jan 1, 2009

By D. C. Dahlin, W. K. O’Connor, G. E. Rush, C. A. Summers, S. J. Gerdemann

The Albany Research Center (ARC) conducted studies of mechanical activation by conventional and ultra-fine grinding techniques to enhance olivine reactivity in mineral carbonation reactions. Activated olivine is one of several solid feed materials used at ARC in reactions with carbon dioxide to form carbonate minerals. This paper compares grinding techniques via energy demand data and product characteristics, including particle size distributions, surface areas, full width at half maximum (FWHM) XRD analyses, and particle morphology by SEM analyses. Reactivity was gauged by percent conversion to carbonate in subsequent carbonation tests.

Jan 1, 2004

By Paul C. Schmall, Arthur B. Corwin, Derek Maishman

Ground freezing occupies a unique and important niche in underground construction, fulfilling a geotechnical need that is difficult, or sometimes impossible, to fulfill through other groundwater control and excavation support methods. Where complete groundwater cut-off and in-built ground support are required, and deep excavation is planned or the work occurs in difficult or disturbed ground, ground freezing offers the assurance critical to safe and timely construction. Compared with other groundwater cut-off or excavation support methods, a frozen wall is easily connected to underlying bedrock and will also adhere to adjoining subsurface installations or obstructions, if necessary, to provide a composite cutoff structure. Ground freezing is effective in all soil and ground conditions and has been used for emergency situations in disturbed, displaced or loose ground, where detailed soil characterization could not practically be performed.

Jan 1, 2005

By J. E. Friant

The Mini-DiscTM cutter drill bit is a radical design departure from the traditional tri-cone rockdrill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-DiscTM drill bit, referred to as the “Disc Bit” has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory can not shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By Rolando Gonzalez

Mexico’s role in the world economic community continues to grow. And it is important that the country makes use of its natural wealth, including its large underground deposits of minerals and metals. With that in mind, Industrias Peñoles S.A. de C.V.(Peñoles), a mining, smelting and refining company, began mining lead, zinc and other metals from the Francisco I. Madero Project (FIM). The mine is located about 600 km (370 miles) northwest of Mexico City in the state of Zacatecas. Peñoles plans to remove about 3 Mt/a (3.3 million stpy) of ore from FIM. To achieve this goal, the company needs to optimize its processing, to maximize the amount of metal it extracts through FIM’s large flotation lead-zinc concentrator. To ensure high productivity, Peñoles and its contract engineering firm, M3 Engineering and Technology, of Tucson, AZ, have implemented anore processing system.

Jan 1, 2003

By S. Krukowski

Iodine is a bluish-black, crystalline solid with sub-metallic luster, and has a specific gravity of 4.93. It volatilizes (sublimates) at ordinary temperatures into a blue-violet gas that has an irritating odor. Iodine is the least active of the halogens, all of which readily displace it. Only slightly soluble in water, iodine also dissolves in carbon disulfide, carbon tetrachloride and chloroform, giving a deep violet solution. The primary sources for iodine production are sub-surface brines associated with petroleum and natural gas deposits, and as a byproduct from nitrate deposits in Chilean desert caliche. The largest source of iodine is seawater which contains 0.05 ppm, or about 31 Mt (34 million st). Seaweed of the family Laminaria can extract and accumulate up to 0.45 percent iodine on a dry basis. Seaweed was an important source of iodine prior to 1959. However, it remains a significant source of iodine in the diets of many populations throughout the world.

Jan 1, 2005

By K. Freytag

The extraction of lignite in open-cast mines has a severe impact on the landscape. Proper landscaping after the shut-down of the mines has always been the statutory responsibility of the mine operator. The large area of the land used for open-cast lignite mining requires special regional planning procedures well in advance of the permitting procedure stipulated in the mining law. The lignite plan determines, among other things, the objectives of land reclamation. These objectives will then be outlined in more detail in the mine operation plans and implemented accordingly. Apart from the actual mining laws and regulations, a large number of environmental laws also determine the process of land reclamation. The success achieved in the field of land reclamation in all mining regions during the recent decades has shown that the lignite mining industry creates new landscapes that do not leave any scars in the countryside and merge very well with it.

Jan 1, 2005

By A. T. Yu, K. A. Young, Ronald M. Hays, Sanford Terry, D. R. Campbell, J. K. Lovrien, W. L. Price, C. W. Matthews, W. R. van Slyke, S. P. Cole

Storage and transport systems are essential for mineral processing. Section 10 includes systems for storage and transport of dry bulk materials, slurries, and water necessary for operation of mineral pro¬cessing plants. All aspects of these systems are presented, including material characteristics; dry material placement in and reclamation from storage stockpiles and bins; dry material conveyance; hydraulics (liquid flow and pumping); slurry characteristics; slurry storage and reclaim, slurry flow (distributors, launders, and pipes), and pumping; water (primary and secondary process, reclaimed, fire, cooling, and domestic) supply, transport, and storage; equipment selection and sizing; power transmission; controls; and health and safety. The mate¬rials considered include crude ore; process and other water supplies; initial, intermediate; and final in-plant materials; finished materials; and tailings and other waste products. Section 10 is a compilation of practical operating data for engineers, technicians, and plant opera¬tors. For the design of mineral processing plants, including selection and sizing of equipment, the design engineer should consult with equipment manufacturers, suppliers, engineering firms, and plant op¬erators with specialized experience in particular materials handling methods. When unusual conditions are encountered, actual pilot or full scale testing may be required to insure adequate design. Operation of mineral processing plants is dependent on the proper engineering and construction of storage and transport systems for dry bulk materials, slurries, and water. It is obvious that processing plants cannot produce the required quantities of semifinished and finished products unless these material can be transported adequately to, through, within, and from the plant. Costs of storage and transport systems may exceed 50% of the total capital and/or operating costs. Considerable attention must be given to the design, layout, and engineering of these systems. These systems are interrelated with the mineral processing method and it is necessary to determine the best combination of mineral processing method and storage and transport systems. Storage and transport systems perform a major supportive func¬tion to mineral processing. The final selection of these systems depends on the final selection of the processing method and related systems (environmental control, tailings and waste disposal, etc.). The process¬ing method determines the characteristics of materials to be stored and transported; distances, elevations, flow rates for transport; and storage requirements. Flowsheet After selection of the processing method and related systems, a flowsheet must be developed. This flowsheet should indicate produc¬tion rate, percent solids or moisture, and specific gravity for all initial, intermediate, and final products or product flow streams. It also may be necessary to know the size analysis, chemical analysis, abrasiveness, and other physical characteristics of various product flow streams. The flowsheet provides basic information for plant layout, storage requirements, and selection and sizing of process and transport equip¬ment. Storage and transport systems often function improperly be¬ cause of inadequate flowsheet data or process revisions, resulting in improper equipment selection and sizing. Further details on plant design are presented in Section 33. After selection and sizing of process equipment, it is necessary to select the type of material transport equipment to be used for in¬plant materials handling as well as crude ore, tailings, and final prod¬ucts. The storage and/or surge requirements, including capacity and location, then are determined. Storage and/or surge capacity is neces¬sary for leveling production rate fluctuations due to variations in material characteristics; production scheduling; equipment mismatch¬ing, failure, or breakdown; and scheduled maintenance downtime. Variations in ore grindability will cause fluctuations in throughput or production rate for grinding mills and variations in ore grade will cause fluctuations in production rate for concentrating equipment. Variations in material moisture content and percent solids can have serious effects on the capacity of material transport equipment. In some cases, a blending system may be desirable or necessary to reduce variations and to obtain uniform production and/or metallurgy. Storage capacity often is needed because of different production schedules for various phases of the mining and mineral processing complex. As an example, the mine and coarse crushing plant may operate on a one- or two-shift-per-day schedule while the fine crushing plant and concentrator on a three-shift-per-day schedule. This would require storage between the coarse and fine crushing plants. Another example would be load-out storage where unit trains are used to haul concentrate or final products. The concentrator could be operated on a three-shift-per-day schedule while only I to 2 hr may be scheduled for unit train loading. This would require adequate load-out storage so that the concentrator can be operated continuously. Process equipment with mismatched capacities requires storage or surge capacity between the mismatched equipment to achieve oper¬ating efficiency. As an example, the fine crushers may have greater capacity than the rod mills. Storage between the fine crushers and the rod mills permits both the crushers and rod mills to be operated at optimum capacity with the crushers actually operating or running a lesser number of hours per day. Mismatched capacities for process and transport equipment also may require storage or surge capacity. Mismatching of equipment capacities most often occurs because of the difficulty in equipment sizing. Thus, the design engineer must anticipate where in the flowsheet these mismatching capacities are likely to occur while making every effort to assure that equipment is selected and sized properly. Equipment breakdown can cause major operating difficulties and lost production. These breakdowns can be reduced with adequate scheduled maintenance. Lost production due to nonscheduled down¬time caused by equipment breakdown can be reduced further by standby equipment and storage and/or surge capacity ahead of essen¬tial mechanical and electrical equipment. As an example, standby pumps and conveyors often are available as part of the in-plant trans¬port system. Storage and/or surge bins and tanks often serve dual functions, such as dewatering, mixing, and smoothing production rate fluctuations.

Jan 1, 1985

By Gordon M. Matheson

The factors which control chimney subsidence sinkhole development in weak rock were assessed by analyzing the characteristics of approximately 3000 chimney subsidence features along the Colorado Front Range. The area of study included features developed over abandoned mines in the Colorado Springs Coal Field, the Boulder Coal Field, and the Foothills District. The approximate locations of the areas studied are shown in Figure 1. Data were collected for sinkholes occurring over both room and pillar, and retreat mining areas in coal seams with a wide range of dips. The location, size, and approximate time of development of each sinkhole were documented. From these data, relationships were developed which describe the time rate of observable sinkhole development and the relative location of sinkhole development with respect to mined height, overburden thickness, and type of mining for relatively flat-lying coal seams. In addition, the observed locations of sinkhole development over steeply dipping coal seams were assessed for portions of the study area.

Jan 1, 1986

By Joy Sandberg

The 1989 mining industry compensation survey done annually by the Denver-based Mountain States Employers Council shows the "average" or "typical" employee in the mining industry is projected to receive an increase of 3.9% to base pay in 1990, compared to a projection of 4.1 % for 1989. According to MSEC, the actual percentage increase to base pay has continued to decline since 1980. A review of pay increases since 1980 shows the highest average increase was 11%, granted in 1981. Since 1981, there has been a steady deceleration through the decade. While 1989 final figures are not available, 1988 numbers might indicate a reversal of this trend. In 1988, the average employee actual increase was 3.8%. That was 0.7% higher than the 3.1% projection. This may be significant as actual increases have been lower than projections since 1982. Chart A shows the pattern of projected vs. actual percent increases in pay since 1980.

Jan 1, 1990

By K. S. Gritton

The implementation of advance control systems brings with it the expectation of improvements in process performance and controllability. Specifically, expectations include a shift in the mean value of the gross measure of process performance, and/or a decrease in process variability. When determining statistically-defensible measures of these benefits care must be taken to preclude process parameters from biasing the determination. Specifically, the effects of ore type, shift personnel, water availability, etc., must all be separated from the effect on performance of the advanced control system. Methods are presented for separating the effects of process control from other process parameters. Examples of the required data analyses are also presented.

Jan 1, 2001

By J. Bilant, B. Carlson, N. Gow

"High-pressure grinding roll (HPGR) technology was evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact on metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data were consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8 percentage points, from 61 percent to 69 percent, and shorten the overall timing of silver recoveries from 20 years to just more than two years.The Rochester Mine, and associated valley fill heap leach facilities is an openpit silver and gold mine located in Pershing County, NV, approximately 42 km (26 miles) northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7 million oz silver (Ag) and 51,000 troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8 in. ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers.Historical recovery rates of crushed Rochester ore averaged 61.4 percent Ag and 95.9 percent Au over a period of 20 years (Robinson et al., 2018). These rates were derived from third-party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher and/ or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project."

Sep 1, 2019

By Jerry T. Shelby

Surface and underground mining operations require equipment with high power output ratings. Haul trucks, loaders, dozers, and other equipment need increasing horse-power to meet production demands. To get more horsepower out of the engines driving the equipment, most manufacturers use turbocharging. Detroit Diesel puts the number at about 90% turbocharged, while Caterpillar estimates 75% to 80% of all its equipment is turbocharged. Turbocharging increases the power output and overall engine efficiency. But it presents some maintenance and operational problems that were not factors when only naturally aspirated engines (nonturbocharged) dominated the scene. A turbocharger is an exhaust-driven air compressor. Using the waste energy in the engine exhaust, a turbine wheel is driven. This wheel is connected by a common shaft to a compressor wheel. The shaft is supported by two plain bearings, or bushings. As the turbine wheel is rotated, the compressor wheel continually compresses the intake air to the cylinders. Compressing the intake air means that more air can be put into the cylinder to burn more fuel. The more fuel the engine can completely burn or combust, the more horsepower the engine can produce. Even though the turbocharger is a relatively simple device, it is a sensitive engine component. It requires special consideration at engine start-up and shutdown. Being freewheeling and exhaust driven, turbochargers can experience temperatures of 540°C 1000°F) and rotational speeds of more than 100,000 rpm. Due to those temperatures and speeds, lubrication is critical to the operation and life of a turbocharger. The turbo is located high on the engine, with the oil supply running through an external line from the sump. The recommended practice is to start the engine and allow it to idle for a few minutes before any revving or loading. This allows the oil to reach the turbo and properly lubricate the bearings before high rotational speeds are seen. Turbo oil supply lines can be as long as 1.5 m (5 ft). Depending on ambient temperatures and oil viscosity, it can take as long as 30 seconds for oil to reach the spinning turbo. However, as little as five seconds without oil can damage the turbo's bearings, reducing its life and overall efficiency. Lubrication problems seen at shut-down can also significantly affect turbo life and efficiency. Manufacturers recommend an idling period of five to seven minutes before engine shutdown. This allows the turbo to slow down and cool off somewhat to help prevent oil coking and bearing damage. When the engine stops, so does the oil supply. There is very little oil left on the bearing surfaces and in the turbo oil supply passages. The immediate heat transfer from the turbine wheel to shaft, bearings, and turbo body literally cooks what is left. This high heat without oil flow can cause bearing deformation by actually melting some of the bearing material. The rapid oil oxidation and coking will restrict oil passages, damage bearings and shaft. Besides heat soaking, there is another problem. If the turbo is spinning at high speeds when the engine is shutdown, the turbo must spin-down to a stop without oil flow. With the large size of turbos used on mining equipment, this spindown time without oil can be for as long as 10 to 20 seconds. Fortunately, lack of lubrication at start-up and shutdown and the subsequent bearing damage can be prevented by oil injection devices. These devices hold a reservoir of engine oil. The oil is injected to the turbocharger bearings immediately on start-up and for several minutes after shutdown. Oil injection devices are spring loaded, hydraulic accumulators. They are actuated at start-up by a solenoid wired to the starter motor. Engine oil pressure charges the accumulator during normal operation. Upon shut-down and loss of oil pressure, the device provides oil to the turbo for about two or three minutes. With an oil injection device, the engine can be started and immediately driven without fear of turbo damage. Also, an abrupt shutdown will not damage the turbocharger since the device will continue to lubricate for two or three minutes. A word of caution. Be sure the oil injection device provides positive oil displacement (pressurized oil flow). Do not use a gravity-flow device. Unless it is a true accumulator, the device could starve the turbo for oil on start-up, Ask for start-up and shut-down pressures and delivery times before considering installation. Keep the oil clean, and follow the manufacturer's recommended oil change intervals. These intervals are usually shorter than with naturally aspirated engines. Use oil with a CD rating designed for diesel applications. A multiviscosity oil is preferable. Use a synthetic engine oil, such as Mobil's Delvac 1, Gulf's Super Duty II, or Chevron's Sub-zero Fluid. Synthetics have much better flow properties at low temperatures. They also have greater oxidation stability (they can take the high heat of turbo-bearing lubrication. And they produce fewer deposits because they are more thermally stable. But synthetic oils do cost more - two or three times more. One additional point - maintain the air intake system. Since all mining is usually in a dusty environment, air filters should be changed regularly and intake systems should be checked for leaks. All intake air passes through the turbo. Any dirt or abrasives entering the turbo will damage the unit and shorten its life. While mining is a heavy duty business with severe operating conditions, you can get the life from your turbocharger that you expect by following a few simple steps: • equip the turbo with an oil-injection device to provide lubrication on start-up and shutdown; • change the oil and filters regularly; and • use the proper oil-synthetic, if possible.

Jan 3, 1987

By J. F. Lupo

Leaching operations combine both metallurgical and hydraulic processes to extract metals from the ore heap. In the design of leaching operations, metallurgical tests and simple hydraulic tests are often conducted to define operational parameters such as leach cycle time, application rate, lift height, and effective leach area. While metallurgical constraints are often the primary focus on leach facility design, the hydraulic factors are also critical to the overall success of the operation. Some of the hydraulic factors that are known to impact solution flow through heaps include: • Ore physical and hydraulic properties, • Variation in ore properties under heap loading, • Ore mineralogy and its susceptibility to chemical and/or mechanical degradation, and • Heterogeneities within the heap. This paper presents a discussion on hydraulic factors that may impact the effectiveness of leaching operations. In addition, methods are presented which may be used to assess flow conditions within active and inactive heaps.

Jan 1, 2000

By Taehong Kim

An accurate and reliable prediction of Tunnel Boring Machine (TBM) performances, in terms of Rate of Penetration (ROP), utilization (U), and cutter wear rate, is a critical element in the successful planning and execution of mechanical tunneling project. Three open hard rock TBM projects were studied to establish possible trends and correlations between rock mass properties and machine performance. Based on this analysis and literature survey, three geological parameters, including RQD, RMR, and groundwater inflow rate, were identified as having the greatest impact on TBM utilization level. Rate of Penetration (ROP) and cutter wear rate were also correlated with fracture spacing, alpha angle, and Cerchar Abrasivity Index (CAI).

Jan 1, 2008

By A. Mahmoudkhani

There has been a continuous interest in chemical aids for processing Canadian oil sands by hot water extraction process since the first commercial industry operation in 1967. Several inorganic and organic chemical systems have been introduced, of which sodium hydroxide is the most widely used extraction process aid by major producers. Use of NaOH, however, results in accumulation of sodium ions in recycled water, causing higher clays dispersion and producing tailings with poor geotechnical properties that turn into mature fine tailings. This is especially true for low grade and oxidized ores, which present the greatest challenges in bitumen recovery and produce the major portion of fine tailings. In this paper, we are presenting a novel method based on use of inorganic polymers as process aids for various low grade oil sands ores. Denver flotation cell and a laboratory scale hydrotransport loop were utilized to evaluate the effect of chemical dosage and operating parameters on the processability of oil sands samples from Athabasca region. Process tailings were examined for properties such as water chemistry, suspended solids, settling rate and the ease of tailing treatments. Our results demonstrate that the use of inorganic polymers during the froth process lead to a significant improvement in bitumen recovery from low grade oil sands and can improve further tailing treatments. This offers a viable solution that can be easily incorporated into current processing facilities and deliver several operational and economical benefits. Advantages in use of inorganic polymers versus sodium hydroxide are presented in details.

Jan 1, 2012

By B. Asbury, M. Cigla, C. Balci

The Western Mining Resource Center (WMRC) at the Colorado School of Mines (CSM) received a grant from the National Institute for Occupational Safety and Health (NIOSH) to perform a study that will help reduce the amount of respirable dust generated from the cutting of coal. The study is based upon laboratory testing and field experience. This information is being used to develop a new cutterhead design in conjunction with Joy Mining Machinery. The new cutterhead design is being evaluated with existing computer models developed at CSM. The new continuous miner cutterhead will be tested at the Twenty Mile Coal Company’s Foidal Creek Mine. Baseline testing with the current cutterhead will also be performed. This paper presents laboratory test results, design methodology, and test results performed to date.

Jan 1, 2002