Search Documents

By S. Hodgson

Introduction The Red Dog zinc/lead deposit in northwest Alaska is the second largest zinc deposit ever discovered. Being developed by Cominco Alaska, with startup scheduled for early 1990, it will ultimately be the largest zinc mine in the Western World. Table 1 shows the reserves of the deposit. Bob Baker, a local bush pilot, discovered Red Dog in 1968. The US Geological Survey assessed the find. But the Red Dog site had been withdrawn from staking by provisions in the Alaska Native Claims Settlement Act of 1971 (ANCSA). Under the terms of ANCSA, the deposit was selected by the NANA Regional Corporation, one of 13 native corporations established by the Act. Then, in 1980, the US Congress confirmed this selection, in the Alaska National Interest Lands Conservation Act. In 1982, Cominco and NANA reached an agreement that has led to the development of the mine. Under the agreement, Cominco leases the property from NANA, develops and operates the mine, and markets the concentrate produced. In return, NANA receives royalties and, after capital recovery, participates in the net proceeds from the operation. The Alaska State Government is also playing a role in the development of the mine. Under the auspices of the Alaska Industrial Development Authority (AIDA), the state will construct, own, and operate the DeLong Mountains Regional Transportation System. This consists of a 84-km (52¬mile) road from the minesite to the Chukchi Sea. Located here are the port facilities necessary to store and ship the annual concentrate production and receive the mine fuel and supplies. For using this transportation system, Cominco will pay an annual toll fee. Over the anticipated 50 year life of the operation, the fee will provide a 6.5% return to the State of Alaska. In late 1986, Cominco's Board of Directors approved the Red Dog project. And, during the summer of 1987, road construction began. In February 1988, initial stripping began at the ore body and construction started at the millsite. Project setting The project site is approximately 1000 km (600 miles) northwest of Anchorage, 84 km (52 miles) east of tidewater on the Chukchi Sea, and 192 km (120 miles) north of the Arctic Circle (Fig. 1). The countryside consists of low, rolling hills that lead into mountains north and east of the deposit. The vegetation is typical tundra mat. And the site is in an area of permafrost. However, the permafrost is relatively warm and some areas have been found to be thawed. Examples would be creek bottoms and the site of the main waste dump.

Jan 12, 1988

By B. DANIEL MARJAVAARA, I. A. SOFIA LARSSON, ANNA-LENA LJUNG

The flow field and coal combustion process in a pilot-scale iron ore pelletizing kiln is simulated using a computational fluid dynamics (CFD) model. The objective of the work is to investigate how the thermal effects from the flame affect the flow field. As expected, the combustion process with the resulting temperature rise and volume expansion leads to an increase of the velocity in the kiln. Apart from that, the overall flow field looks similar regardless of whether combustion is present or not. The flow field though affects the combustion process by controlling the mixing rates of fuel and air, governing the flame propagation. This shows the importance of correctly predicting the flow field in this type of kiln, with a large amount of process gas circulating, in order to optimize the combustion process. The results also justify the use of down-scaled, geometrically similar, water models to investigate kiln aerodynamics in general and mixing properties in particular. Even if the heat release from the flame is neglected, valuable conclusions regarding the flow field can still be drawn.

Apr 20, 2021

By William G. Fischer

Basic laboratory tests initiated the. Rock Mechanics program. The stress-strain curve, modulus of elasticity, Poisson's ratio, the uniaxial rock strengths, Mohr's envelope, the stress at failure, and creep were investigated. A series of underground problems were then approached using this information; and various field measuring devices, most of which were developed by the Bureau of Mines. Initially, stress concentrations near mine openings were evaluated using the stress relief technique. This required an accurate determination of the pre-mining stress field. Later, stress concentrations associated with the cave line .sere studied. After about thirty stress reliefs over an appropriate time interval the effects of one type of mining could be compared against another. The microseismic technique was used to investigate a possible application of warning devices near the cave line. A study of mane reorientation was made Problems related to the shape and size of pillars and barriers were studied. Partial extraction mining systems were evaluated. The effectiveness of roof bolting patterns were examined. Control of roof stresses was attempted. A new system of mining in heavy ground has been developed using the information secured in the Rock Mechanics program without this system, mining in more than one instance would Nave been next to impossible. Indeed; from this one discovery alone, the Rock Mechanics program has paid off in improved safety as well as in dollars.

Jan 1, 1964

By Neall. George M.

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U.S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions. A review of the literature reveals that some work has been conducted on the roof truss. 1 Gambrell and Haynes (1970) showed that the roof truss is superior to angled roofbolts installed through a header. Sheorey, Verma, and singh2 (1973) used statics to prove that the optimum angle of inclination should be greater than 450? However, to date, no systematic attempt has been made to establish design criteria. In this report, the problem was approached in three ways. First, model studies were performed to determine general trends of truss support as a function of a number of variables. This provided a better understanding of the support mechanism involved. Secondly, beam theory was employed to calculate the actual support capacity of a truss, realizing the many simplifications, assumptions, and shortcomings of this approach to such a complicated problem. Last, field testing will be utilized to test the hypotheses previously developed and provide hard data to further synthesize roof truss design criteria. Field testing has recently commenced and should be complete before mid 1977.

Jan 1, 1977

By William J. Shampine

This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map. This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map.

Jan 1, 1966

By T. Murt, C. Oñate

In recent years, environmental considerations have played a prominent role in underground construction projects. The management and disposal of the muck produced by an EPB TBM is an important aspect of this topic. Soil conditioners with higher biodegradability and lower eco-toxicity have been specifically developed to comply with strict regulations in several countries around the world, with the goal of reducing the environmental impact of tunneling on soil, water, and living organisms. This paper highlights innovative sustainable soil conditioners and how they differ from traditional products. Additionally, environmental considerations for TBM projects around the world and in North America will be examined.

Dec 1, 2022

By J. Sattarvand, P. C. Augustine

Despite significant safety improvements, the mining industry remains one of the most hazardous occupations globally and the evacuation of Miners, when an uncontrollable incident occurs in the mine, is the best bet to saving lives. However, Human factors/behaviors during an emergency are likely to influence the evacuation performance. Other industries have made a significant effort to determine these human factors that can impede evacuation performance, however, the current state-of-the-art in mine evacuation or self-rescue is that the evacuation route is predetermined, and a static sign is used to direct miners to the predetermined safe location. This method is limited in representing actual conditions that arise in a real emergency, neglecting the different behaviors displayed by humans. As optimization of the evacuation of a mine plays a fundamental role in emergencies and modeling evacuation behavior and movement of miners is a complex task, this research utilized Agent-Based simulations to simulate the evacuation behavior and performance. It was observed that people with the smart evacuation device made fewer mistakes and arrived at the safe place in less time compared to those have no access to the device. The Mathematical model used in optimizing the shortest path to a safe place is also explained in this paper.

Jun 25, 2023

By M. Yekeler

The critical surface tension of wetting values (Ye) of realgar (AsS), talc [Mg3si401o (OH) 2]' stibnite (Sb2S3), and sulfur (S) were determined by flotation in the absence of conventional flotation collectors as 38.7, 38.0, 35.5, and 30.0 dyne/cm, respectively. The surface tensions of flotation media were arranged by methanol. Separation of binary mixtures of these minerals was performed exploiting their Ye differences-which form the basis of the "ganuna flotation process". One step flotation test showed that sulfur floats preferentially from its mixtures with realgar and stibnite at recoveries of 73.6 and 70.7 % and grades of 81.7 and 91.2 %, respectively. The separation of stibnite from realgar gave a recovery of 4.1 % and a grade of 41.2 % for stibnite, indicate that a minimal Ye difference of 3.6±0.2 dyne/cm is essential for such separation when conventional flotation reagents are not used. This paper presents data and describes the approach employed in these separations.

Jan 1, 1994

By T. E. Bernard

"Refuge alternatives (RA) provide shelter to miners trapped underground during a disaster. RA manufacturers must demonstrate that their RAs meet the Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and the management of heat that results from the RA occupants and mechanical/chemical systems. In this study, miner size and activity level were used to determine the metabolic heat rate, oxygen requirements, and carbon dioxide generation that is representative of miners in a refuge situation. A convenience sample of 198 male miners was used for the distribution of current US coal miners, and the composite 95th percentile height and weight were determined to be 193 cm (76 in) and 133 kg (293 lb). The resting metabolic rate (RMR) was determined to be representative of activity level in an RA. The highest likely metabolic heat generation ranged from 115 W to 135 W, depending on RA occupancy. The highest required oxygen supply and carbon dioxide removal were estimated to be 23 LO2/h/person (0.81 ft3/h/person) and 20 LCO2/h/person (0.71 ft3/h/person), which means the margin of safety is 50% or more when compared to the MSHA requirements. INTRODUCTION Refuge alternatives (RAs) provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their RAs meet Mine Safety and Health Administration (MSHA) requirements for the supply of oxygen, the removal of carbon dioxide, and the management of heat that results from the occupants and the mechanical/chemical systems in the RA [1]. These MSHA requirements were based on a standard 70 kg (168 lb) male with an assumed allocation of activity of 80% rest and 20% moderate activity level [2]. The purpose of this paper is to re-examine the metabolic heat generation and oxygen and carbon dioxide requirements of miners in an RA based on actual miner size and more realistic RA activity levels based on current RA designs. The purpose of this paper is to re-examine the Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and heat generation. To achieve this, researchers took the following steps to estimate the metabolic demands and the associated heat generation, oxygen requirements, and carbon dioxide production. 1. Characterized the anthropometric characteristics of the miner population. 2. Described the metabolic rate profile of RA occupants. 3. Characterized the maintenance demands of RAs. 4. Summarized oxygen supply and carbon dioxide removal volumes. ANTHROPOMETRIC CHARACTERISTICS OF MINERS The weight, height, and age distributions of the adult male populations are summarized in Table 1. For each data set, the reported mean and standard deviation are provided. The 95th percentile (%ile) value for height and weight for each population was the mean plus 1.64 times the standard deviation."

Jan 1, 2017

By F. P. Schwarz

Even in an otherwise care-fully done sampling procedure, reducing subsample weight, or splitting, when the grain size of material is too large commonly generates significant error. Such error can be estimated from the standard deviation of differences between values of PAIRED ASSAYS. Samples from split-ting steps immediately before comminution, and showing a restricted range of grade, generate paired assays. Splitting steps characterized by relative standard deviations exceeding 16% generate nonrepresentative data. Such steps should be redesigned to optimize reliability of assay-dependent studies. A sampling scheme can be graphically characterized, and then redesigned as appropriate, using a SAMPLING NOMOGRAPH. Use of the nomograph avoids continued replication of assays. Generally at a splitting step, excessive error can be reduced by comminuting more material. Unnecessary effort can be mitigated by comminuting less finely and/or by splitting to a smaller weight.

Jan 1, 1992

By Z. Rogovin

A Knowledge of the amount of time the material spends in a continuous mill in a closed-grinding-circuit is essential for circuit performance analysis and scale-up design. A convenient method for acquiring this information involves the use of tracers in residence-time-distribution (RTD) experiments. In a typical wet process the RTD measurements are usually done by injecting a pulse tracer into the mill inlet and detecting it in the circuit exit. In this article a simple to use mathematical method for the calculation of the closed circuit material residence time in the mill is developed. Using this method there are no restrictions on the location of the tracer injection or detection points. Any convenient location in the closed circuit can be chosen without affecting the simplicity of the method. This method also enables the calculation of the degree of mixing in the mill. The use of this method for the analysis of impulse response data obtained from several commercial grinding circuits is presented.

Jan 1, 1986

By Akram Marseet, Andrew J. Petruska, Rik Banerjee

Event cameras are used for their performance in high dynamic-range lighting conditions which are canonical to active mining environments. Direct labeling of event-based image data to train a model to perform semantic segmentation using traditional methods is slow and error-prone. This study proposes a framework to use roughly hand-labeled color images from a mine as an input to an intermediary probabilistic algorithm called alphamatting to generate a ground-truth data set. These high-fidelity labels can be used to train a semantic segmentation model to differentiate the support strap from the roof. This model can then be leveraged to segment an event-based scene to enable autonomous roof bolting. This pipeline has been shown to achieve an accuracy of 88% with a false positive rate of 3%.

Feb 1, 2024

By STEVEN J. SCHATZEL, Zoheir Khademian, KAYODE M. AJAYI

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine, creating safety concerns. To provide recommendations for developing guidelines that ensure a safe coexistence of longwall mining and unconventional shale gas production, this study uses a discrete fracture network (DFN) model to evaluate the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations are within values validated with field measurements.

Mar 1, 2023

By R. H. King

Underground coal mining machinery utilizes portable electric sables, "trailing cables." to obtain power from load centers or distribution boxes. Cables are frequently damaged since mobile equipment, poor lighting, and restricted space are inherent to coal mining operations. Normally, the damage is repaired by splicing--the joining of one or more severed conductors and replacing insulation and jacket. Figure 1 illustrates a typical single conductor splice. Although the repair seems simple, difficulty of the splicing process is exemplified by the many safety hazards and frequent production delays that result from defective splices. Forty-two cable splice related injuries were reported to the U.S. Bureau of Mines in 1972 and 1973. Additionally, 17 splices related fires were reported in the three year period prior to December 1972. Assuming the damaged area is quickly located, an average splice time for a two conductor cable is twenty minutes. Some operators estimate this delay is incurred once per day per operating section. If one ton per minute is averaged throughout the shift, each unit could loose 4800 tons per year from splice delays. An estimated cost for materials and labor to make a splice is $20. The expenditure could result in a $4800 annual cost per section. The estimated expense does not include wages of other personnel waiting for the repair to be completed. Nevertheless, labor and materials cost is minor compared to the income lost from decreased production.

Jan 1, 1975

By Angelina Anani, Nathalie Risso, Carlos Olmos de Aguilera

The traditional approach to safety clearance monitoring and proper PPE usage in underground mines is time-consuming, costly, and susceptible to negligence. However, automated real-time monitoring can be implemented using computer vision-based approaches. This study aims to develop a system that provides timely information based on the automatic detection of proper PPE use and safety clearance in underground mines. Deep learning and a decentralized computing structure between the cloud and sensing devices (fog technology) are used. We hypothesize that a camera-based system can provide near real-time assessment of proper PPE use and verified clearance to access restricted areas in underground mines.

Jun 25, 2023

By J. H. Rowland, R. A. Thomas, III, C. D. Litton

Atmospheric monitoring systems (AMS) are required when using air from conveyor belt entries to ventilate working sections in U.S. underground coal mines. AMS technology has the potential to increase fire safety mine-wide, but research is needed to determine the detection and response times for fires of a variety of combustible materials. To evaluate the potential of an AMS for fire detection in other areas of a coal mine, a series of full-scale fire experiments were conducted to determine detection and response times from fires of different combustible materials that are found in U.S. underground coal mines, including high- and low-volatility coals, conveyor belts, brattice materials, different types of wood, diesel fuel, and a foam sealant. These experiments were conducted in the Safety Research Coal Mine (SRCM) of the U.S. National Institute for Occupational Safety and Health (NIOSH) located in Pittsburgh, PA, using a commercially available AMS that is typical of current technology. The results showed that through proper selection of sensors and their locations, a mine-wide AMS can provide sufficient early fire warning times and improve the health and safety of miners.

Jan 1, 2016

By Taghi Sherizadeh, KUTAY E. KARADENIZ, Dogukan Guner, Samuel Nowak

Underground mining environments bring with them occupational health and safety issues with some severe dangers, such as mine explosions. During such events, miners may escape using main access openings or find a safe haven like a refuge alternative (RA) to wait and be rescued and evacuated to the surface. In this paper, RAs are explained with their early and current applications. A classification as permanent and portable is detailed, depending on conditions and abilities. This classification is followed by the utilization and survivability of RAs with the requirements and recommendations of the main mining countries. Based on the utilization and survivability constraints, basic human requirements, waiting for a rescue team, and the required physical specifications of RAs during the events are analyzed in detail for various countries with their regulations. Among these, the specification of resistance to explosion is discussed in particular, and studies in the literature are examined in terms of structural deformation.

Mar 1, 2023

By T. Knuutinen, M. Klemetti, P. Mörsky

This paper presents a comparison study done at VTT's new pilot plant facilities in Outokumpu, Finland, for chromite ore. The ore was ground in a rod mill -, a ball mill - and high pressure roller mill - ball mill circuit in the capacity range of 0.5 - 3.0 t / h. The main grinding characteristics are discussed and the quality of the products are compared from the mineralogical point of view. The benefits of high pressure roller mill comminution for further mineral processing of chromite is also discussed.

Jan 1, 1995

SOLUTION MINING Solution mining techniques present a means of extracting soluble ores, particularly such materials as salt and potash, from horizons which are not accessible by conventional mining. In the process of dissolving materials, it is evident that solution may be complete or partial. In general, the solution mining operations described in the following section relate to complete solution of the desired compound. Even though the solution of material is complete, there may be instances in which insoluble material is present to a large extent either as granular separated particles or as insoluble layers. The process required for obtaining the desired product involves access wells to reach the deposits, sufficient water supply to yield the production goals, and the development of an underground cavity. The process of solution mining, therefore, depends to a great extent on three factors: availability of a relatively pure strata or formation of salt or potash to be mined, access well or wells, and adequate control of the solutioning process so that enlargement of underground cavities can be fairly well delineated. Since halites represent the most general ores mined by this procedure, the considerations which follow are based primarily on the production of sodium or potassium chloride. The producing formations may be in the form of bedded evc~porites wherein the salt member may be some 30 to 500 ft thick or from salt domes in which great depths of salt occur. Solution mining has been carried out to depths of nearly 10,000 ft. The recovery of saturated brine from wells drilled to effect the solution-mining process leads to further processing. In many instances, the procedures are relatively simple and involve simple recrystallieation or fractional crystallieation, while in others more complex flow systems are required before a final product is obtained. The intent of this section is to provide information relative to the basic procedures for obtaining materials which are soluble in water and to acquaint the engineer with the various aspects of the overall problem which in many instances, may become quite complex and present numerous difficulties. The storage of fluids, particularly hydrocarbons, underground has proven to be a very important part of industry operations. Cavities formed in salt provide excellent storage facilities. The formation of well-defined controlled configurations of such cavities has been possible because of better understanding of the solution process, wide experience gained over nearly 30 yr, and improved technology in drilling and completing wells, surveying caverns, and the operation of numerous types of systems. Solution mining techniques will improve in the future. Many facets of the simple operation of pumping solvents and extracting valuable minerals require further study. Developments undoubtedly will occur to further the processes of mining by solution. In addition to those whose names appear in connection with the individual subjections which follow, a major role in assembling and processing the material in this section was played by Dr. D. A. Shock, Central Research, Continental Oil Co., Ponca City, Okla.

Jan 1, 1973

By A. Galicia, A. Charest

The Marlin deposit is a low sulphidation Au-Ag, epithermal system, with reserves of more than five million ounces gold equivalent. Marlin was discovered in December 1998, after a nine months grassroots exploration program in western Guatemala, focused on volcanic terrains of the Sierra Madre. Before the Marlin discovery, several gold prospects were found along an east-west corridor of approximately 70 kilometers long, associated to regional faulting systems. The deposit is hosted in faults, within Tertiary andesitic rocks and bedded volcano-sediments. Host-rocks are argillized closer to the surface and propyllitized at depth. Mineralization occurs in multi-stage quartz stockworks and breccia veins.

Jan 1, 2004