Search Documents

By Yuemin Zhao, Daniel Tao, Rick Honaker, Maoming Fan

"Froth flotation is the most widely used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles around 700 nm in diameter can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubbles on the flotation performance of different particle size fractions of coal was investigated using a bank of 10-L flotation cells, a specially designed 50-mm inside diameter column and a 152-mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during the froth flotation process improved flotation efficiency. The use of nanobubbles in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.IntroductionFor minus 0.6 mm fine coal or minus 0.15 mm ultrafine coal particles, froth flotation is known to be the most efficient and the most cost-effective separation technique. However, flotation efficiency decreases sharply with ultrafine and relatively coarse coal particles. Studies have shown that the low flotation efficiency of ultrafine particles is mainly due to the low probability of bubble-particle collision (Yoon et al., 1989; Ralston and Dukhin, 1999). Enhanced flotation of fine and ultrafine coal can be achieved by increasing collision and attachment probabilities.The top size of particles that can be recovered by flotation depends on the combination of mineral properties and flotation devices. Turbulence in flotation devices is an important factor that affects the stability of bubble-particle aggregates. Even in the flotation of fine particles, bubble-particle detachment can significantly influence the kinetics of flotation taking place in mechanical cells, which provide intensive turbulent agitation (Deglon et al., 1999). Coarse particle flotation is more difficult, because increased agitation is required to maintain particles in suspension and coarse particles are more likely to detach under turbulent conditions (Mankosa and Kohmuench, 2002; Soto and Barbery, 1991). More efficient attachment of particles and improved flotation rate has been observed when tiny bubbles coexist with conventional-sized flotation bubbles (Attalla et al., 2000; Tao et al., 2010; Fan et al., 2010a, b, c, d; Fan et al., 2012)."

Jan 1, 2015

By Stephen D. Schwochow

Aggregate producers nationwide well recognize the numerous problems often faced in securing local approval to open and operate new gravel pits and rock quarries. Similar problems are faced in Colorado, but this region also presents certain political, social, and geological complexities that have become particularly troublesome in the last 10 years. The gravity of the local permitting dilemma can be related directly to the worsening supply-demand imbalance for aggregates in the state's most populated area, the Front Range urban corridor, particularly the Denver metropolitan area. The drive to develop crushed-rock reserves to supplement dwindling alluvial supplies and to meet increasing regional growth demands was somewhat predictable but perhaps more a "last resort" alternative forced onto producers by a hesitant and often apathetic government.

Jan 1, 1982

By Jacques B. Wertz

Although fracture intersections and "domes" seem at a number of places to be the basic structural combination for the occurrence of a mining district, of the porphyry-copper type particularly, this situation is, of course, not always to be expected. For instance, the group of mines comprising Superior, Ray, Miami, Globe, Christmas appeared from the beginning of these structural studies as typical exceptions, and there are others. One had to expect additional parameters to allow for any mineral concentration to occur. One of these apparent parameters is here considered. From the result of stratigraphic studies related to ancient formations in Southeast Arizona, the Martin limestone (Devonian in age) was retained as having a possible relationship with the structure-economic studies in progress, as evidenced for instance by the mineralized O'Carroll bed located at the base of the Martin. This limestone formation has been rather extensively investigated in the past and there are many known sample localities. For this work, the isopach map was drawn by computer to insure more objectivity and, in addition to the available data points, a number of dummy points with a zero value were added around the assumed form-

Jan 1, 1971

By I. H. Gundiler

Although cyanidation has been universally applied in the processing of gold and silver ores, the search for less toxic alternatives continues. Difficulties encountered in processing ores containing oxidized copper minerals and the inherently slow kinetics of cyanidation have generated a renewed interest in thiosulfate leaching. This process, as well as the catalytic effects of copper ion, were well recognized and widely applied towards the end of the past century. In this study, the effects of copper, ammonia, and thiosulfate concentrations on gold dissolution were investigated using the rotating disk technique. Extraction of gold and silver from an oxidized copper-bearing ore was also studied utilizing a statistical experimental design, and these results were displayed in the form of contour plots.

Jan 1, 1993

By George F. Weaton

During the past eight years there has been a dramatic change in the iron ore industry of Minnesota, in that its status has changed from that of a seller's market to a higly competitive buyer's market. Minnesota's natural ores must now be beneficiated and up-graded considerably to be marketed in order to compete with the higher grade foreign ores as well as with the locally produced and highly desirable taconite pellets. With the passage of the "Taconite Amendment' in the November, 1964 election, the taconite industry commenced to expand in Minnesota, which, although initiated in that state, was benefiting many other states and some foreign countries to a much greater extent than Minnesota. These other areas were actually appropriating markets that had been established and retained by Minnesota for many years. Since the approval by the state voters of this amendment, there has been a great increase in the development of taconite properties on the Mesabi Range.

Jan 1, 1966

By Luis R. Bittencourt

Research efforts have been made to characterize a refractory Brazilian bauxite ore composed basically of gibbsite, kaolinite and quartz. Detailed polished-section microprobe analysis of the unbroken ore has been used to describe the liberation characteristics and the association between mineral phases. The linear grade distributions for selected particle size fractions were determined by means? of a particular implementation of King's Random Fracture Model that uses the exponential model for the distribution of linear intercepts through both dispersed (kaolinite) and continuous (gibbsite) phases. The corresponding volumetric grade distributions were then determined by means of a constrained optimization technique for the solution of the transformation equation. Batch flotation experiments were carried out to determine the kinetics for particles of different sizes and the results correlated with the liberation spectrum for each size class.

Jan 1, 1991

By Hervé Le Bissonnais, Jean-Pierre Janin, Anne Bergère, Pierre Renier

"The most important impact on the environment of a tunnel excavation is the creation of surface settlements. Nowadays, the mechanized tunneling allows minimizing the settlements, applying a confinement pressure which counterbalances the ground de-confinement. It is thus essential to determine the correct amount of confinement pressure. In this paper, the authors present a 3D numerical study simulating the EPB-TBM excavation of a water tunnel, in the Flanders clays (north of France). Firstly, a simplified 3D simulation, based on the concept of instantaneous longitudinal settlement curve, was performed to predict the surface settlements for different values of heading confinement pressures. Secondly, the same pressures were tested by the EPB-TBM in a monitoring zone. The comparison between the prediction settlements and the measurements was very satisfactory and allowed validation of the numerical approach and the choice of the optimal confinement pressure value for a sensitive area of the project. INTRODUCTION The excavation of a tunnel can create displacements of the surrounding soil which may affect existing structures and generate unacceptable dysfunction. The development of the closed shield tunneling has permitted to reduce the volume loss generated around the excavation and consequently the surface settlements. In this case, as explained by different authors (Clough et al., 1985; Kastner et al., 1996; Mair and Taylor, 1997), the ground movements are influenced by the TBM works: the heading confinement pressure, the shield overcutting and conicity, the annular void grout injection parameters, the segment concrete lining rigidity, the consolidation of the grout. Hence, in the tunnel design, it is important to take into consideration these different processes of the excavation works to simulate correctly the tunneling process."

Jan 1, 2016

By D. E. Cameron

"INTRODUCTION Grade control requirements for base and precious metal projects are an important input to both conceptual and feasibility mine plans. It’s the author’s experience that grade control input is insufficient at these critical stages. The few exceptions are a stimulus for this paper. A significant portion of CRC’s practice has involved assisting operations to solve grade control issues which were finally recognized as contributing to negative production variances. Even in operations perceived to be successful, deficiencies in grade control are often masked by measures taken by an operation to compensate a deficiency in one area with outperformance in another. The advantages in having a realistic and adequate grade control plan developed at an early project stage by a geologist(s) with considerable operations experience are manifold. It’s important for the geologist to prepare clear inputs into the mine plan backed by detailed supporting information in usable, flexible formats. When the decision is made to advance a project, the exploration team passes its model to a mine planner. The team doesn’t usually provide a detailed grade control plan with the block model, thus the planner tends to treat grade control as an activity to be rolled into a broader operating category. The consequences of highly compartmentalized mine planning can be severe in the long run. Once a plan is tabled, and especially once production begins, it is very difficult to improve grade control outside the fixed parameters of the operation. Major fixes tend to be costly in terms of time and dollars. Implementing needed changes to the grade control practices and culture in an established mine can present almost insurmountable difficulties. Hypothetical examples of grade control planning are presented to illustrate the author’s points. The diagrams are conceptual and schematic; any resemblance to actual deposits is coincidental. BEYOND 50¢/TON In more than a few cases, grade control cost is buried in a subcategory of mining cost with little more consideration than a plugged number. It is possible to do a word search in 43-101 Technical Reports on advanced projects and without finding reference to “ore control” or “grade control”. The idea is to reach the orebody by the shortest and least expensive means, achieving production and investor payback at the earliest possible occasion. This entails a low stripping ratio pit or a decline ramp with sills on ore to prepare the first stopes. The processes to achieve the target production, one of which is grade control, will fit into this framework. After all, there is a block model and the planner can see the grade and tons in each block. The exploration geologist whose responsibility was to bring a large percentage of the deposit into mineral resource owns the model and has released it to planning. Now comes the planning stage. Mine geologists haven’t been hired yet and they will be phased in with production. What could go wrong? Larger companies may have the geologists with operating depth who will be inserted into the mine planning discussions, but it’s not a given. Junior companies must often delegate the conceptual and detailed planning tasks to consultant groups. Is a senior-level grade control review part of the scope of work for the mine planning? If a good grade control plan is in place before the mine geology team is staffed, a key element of success is assured."

Jan 1, 2018

By Cuthbert Musingwini, Adeodatus S. Nhleko, Mahlomola I. Mabala

Optimization of a three-dimensional (3D) underground stope layout is complex given the number of variables and constraints to consider, such as the stope size. Determination of the appropriate stope size in stope layout optimization problems is a complex process that must consider several factors including placement of infrastructure and development, production scheduling, and equipment selection. An inappropriate stope layout can result in unrealistic expectations for a production schedule, consequently negatively affecting the derived economic value. Therefore, this paper used a dual interchange algorithm (DIA) to evaluate the effect of stope size on the stope layout economic value (SLEV) for a synthetic Platreef mineral deposit planned for extraction using sublevel open-stoping. The results showed that generally as the stope size increases, the SLEV decreases. This aligns with practical mining because larger stope sizes have a higher chance of incurring more dilution which reduces economic value, while smaller stope sizes enable more flexible extraction where unprofitable blocks can be left unmined as waste, thus increasing the derived SLEV.

Jun 25, 2023

By John W. Stevenson, Ted L. Sartain

Underground booster fan installations are currently employed in hundreds of coal mines throughout the world. Such installations, when properly designed and maintained, have proven to be safe and effective tools to provide desirable airflow volumes on sections or in areas of mines where the ventilation requirements exceed the capacity of the main fan system. In cases where an airshaft cannot be justified due to surface topography, depth of cover, or limited reserves a booster fan can serve the same purpose, be operational in a fraction of the time and at a substantially reduced cost. Booster fans are currently non-existent in U.S. coal mines. This is primarily due to lack of acceptance by the Mine Safety and Health Administration (MSHA), which has failed to acknowledge the merits of a booster fan system. Also, the absence of booster fan provisions in Part 75 of the federal regulations has led to the misconception that booster fans are legally prohibited in U.S. coal mines. In 1986, Jim Walter Resources, Inc. (JWR) developed and submitted to MSHA a plan to install and operate an underground booster fan at the No. 7 Mine. Detailed computer simulations were used to substantiate JWR1s position, that the booster fan could effectively provide the needed airflow on a developing section without adversely affecting ventilation in other areas of the mine. JWR also realized that numerous safeguards and operating procedures were essential for providing a safe system. Thus, safety features such as electrical interlocking, independent power supply, remote atmospheric monitoring, etc., were incorporated into the plan. This paper is a case-study that discusses JWR's proposed plan to install and operate an underground booster fan at No. 7 Mine. Unfortunately, MSHA's continued negative response has prevented implementation of the plan.

Jan 1, 1989

By R. S. Kasper

This paper reviews the procedure used to quantify the conveyor frictional resistance on a 3.9 km (2.4 mile) long overland conveyor belt. Field torque measurements of the three drives were used to help fine tune a computer simulation of the conveyor. This enabled the prediction of the effect on various conveyor components that cold temperatures will have on increasing the throughput tonnage.

Jan 1, 1995

By K. J. Stanaway

Concentrations of minerals between 3.5 and 5 specific gravity such as ilmenite, rutile and zircon in large accumulations of sand constitute "heavy mineral" placers. Two fundamentally different modes of formation characterize "trap" and "bed" placer variants. Smaller and generally higher grade trap placers form during sediment erosion or reworking. Because of their smaller size, they rarely yield economic heavy mineral deposits. They become economic, either if they contain more valuable "heavies" such as gold, or, if they occur within or near much larger but lower grade bed placers. Bed placers form during sediment accumulation episodes in any environment and lithofacies where mineral supply and fluid dynamics are favorable. Three heavy mineral deposits are discussed to illustrate bed placer geology and how trap placers occur with and relate to them.

Jan 1, 1991

Unplanned ore dilution can have severe impact on the economics of a mining operation. The paper discusses and distinguishes between controllable and natural parameters influencing ore dilution, and how it can be minimized in longitudinal mining systems of narrow vein orebodies. It is shown through data of surveyed stope profiles and numerical modelling that unplanned ore dilution is a function of stope design and construction, orebody geometry, and rock mass characteristics.

Jan 1, 2010

By Syd S. Peng

In the past few years, the numbers of underground coal mines in this country using longwa11 mining method have been dramatically increased. In the latest count there are approximately 90 10ngwa11 faces amounting roughly 8% of the total underground production. Meanwhile, shortwall mining adapting longwa11 powered supports to 'coal mining and handling systems in room and pillar mining is also gaining importance in the Appalachian coal field. Although there are only 7 operating shortwall faces so far, indications are that it will be increasing steadily. Modern longwall faces are highly mechanized and productive. One of these key elements that contribute to the success of modern longwall mining is self-advanced powered supports. There are several types of powered supports. Frame type is two sets of one to four hydraulic legs supporting beam-type roof canopy and floor base. However, chock type is more popular and connected to broad roof and base structure. Shield supports were introduced recently but proved to be highly successful (1). A shield support consists of two hydraulic jacks mounted between a base plate and a gob shield. The base plate is hinged to gob shield which is in turn hinged to roof canopy.

Jan 1, 1977

By Q. Feng

"Efforts have been tried to apply the mixture of mine tailings and fly ash as construction materials. Through the present investigation, a protocol to make construction materials using the mixture of mine tailings and fly ash has been set up. The experiment results of the present work also help set up the working conditions such as activation temperature and time, the concentration of NaOH, the addition of Ca(OH)2, forming pressure, mine tailing to fly ash weight ratio, curing temperature and curing time. The findings of the present work provide a novel method for the geopolymerization of the mixture of mine tailings and fly ash as construction materials, such as bricks for construction and road pavement. INTRODUCTION In mining activity, after the valuable materials are extracted from ores, millions of tons of solid rejects, i.e., mine tailings, are stored in the tailings dam, which occupies a huge area of land and leads to high monetary, environmental and ecological costs. For example, the impoundment of mine tailings can bring with serious environmental problems such as mine dust and tailing dam failure. On the other hand, the making of general construction material results in a lot of greenhouse gas emission. Therefore, it is of great interest to utilize mine tailings, for which a lot of energy has been consumed during the comminution process, as construction materials using the novel geopolymerization technique. (Xu and van Deventer, 2000, 2002a, 2002b; Pacheco-Torgal et al., 2007, 2008; Zhang et al., 2011; Ahmari et al., 2012) Fly ash is another industrial waste which needs to be carefully impounded because of its potential impact on environment. Many efforts have been tried to utilize fly ash as construction materials because it is a silica/alumina rich aluminosilicate source. In addition, the facts that fly ash is quite reactive to alkali and its particle size is usually very small (< 50 microns) make the specific material an ideal source for the geopolymerization process to make construction materials. Geopolymerization is a process of obtaining a polymeric structure from aluminosilicate by dissolving aluminosilicate sources in a strong alkali (NaOH) solution at an elevated temperature. After being cured at an elevated temperature for a specific time, the geopolymerization product shows a greatly increased compressive strength. Therefore, the product can be used as construction material such as bricks and road pavement. It provides a very promising method to apply aluminosilicate sources such as mine tailings and fly ash as construction materials."

Jan 1, 2016

By M. A. Cornachione

The west central upper Peninsula of Michigan contains a large resource of graphitic slate. The slate has potential industrial use as a substitute for shale currently used in the production of portland cement. Some of the unweathered slate, however, has a high concentration of pyritic sulfur which can create emission problems when processed in a kiln. A low cost method to reduce the sulfur content of the slate through the optimization of pyrite oxidation in a bio-heap leaching operation was investigated.

Jan 1, 1992

By R. F. Harig

Designing an underground nuclear waste repository is a complex process. Although many decisions are involved before the design is complete, the first three--what the target horizon is, what the underground boundary is, and where the entry point will be located--are important because they establish the basis for the entire repository design. Even more important than these decisions, however, is the data on which the decisions are based. Because the current data are limited, an aggressive data gathering program is needed during the next design phase to augment information about the intricate interplay among all facets of the repository design and the geologic medium in which the proposed repository is to be developed. Although unique to modern engineering enterprises, the challenges involved in designing a repository in the unsaturated zone are within current technology and engineering practices.

Jan 1, 1991

By J. Paraszczak

Water-powered jackleg rock drills, introduced recently in South African mines are reported to be more efficient, faster and more comfortable to operate than conventional pneumatic drills. A comparative testing of both drill types was performed in Quebec. Based on its results and time studies done in the mines, water-powered drilling has been reviewed with regards to drilling rates achieved, infrastructure needed, side effects, health and safety considerations. This study shows that the application of water-powered drills may help increase footage drilled and improve working environment, but under specific conditions. The examples of such applications are given in the conclusions.

Jan 1, 1995

By E. Poeck, R. Garvey, U. Ozbay, K. Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the mine-scale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures which most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps. INTRODUCTION The analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but for deep cover and squat pillar geometries, less accuracy has been achieved in predicting pillar performance (Mark 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs. This paper presents a study of pillar stability through the back analysis of the Crandall Canyon Mine collapse, which occurred in August of 2007. Pillar-scale models are utilized for the calibration of material properties and assessment of potential instability under varying conditions, and mine-scale models are constructed in an attempt to reproduce widespread failure and correlate with observations at the mine. Special consideration is given to the properties of the coal and the coal/rock interface, and kinetic energy is calculated throughout the course of the simulations to gauge the level of instability when pillar failure occurs. Models were constructed using the Universal Distinct Element Code (UDEC) (Itasca, 2014)."

Jan 1, 2016

By Arthur W. Ruff

The iron-ore beneficiation and shiploading facilities of the Marcona Mining Company are at San Nicolas Bay which is on the Peruvian coastal desert about two hundred and seventy miles south of Lima. The mines are at elevation of 2,500 ft. Crude ore is transported from the Mine primary crushers to the beneficiation plants by ten miles of overland belt conveyors. After the predominantly magnetic ore is reduced to minus 3/4 in. in the secondary crushing plant, the ore is ground by rod and ball mills and concentrated with magnetic separators. The concentrate slurry is pumped to a thickening and filtering installation for desliming and dewatering. Pelletizing is accomplished with a Lurgi and also a Dravo-Lurgi machine. Deep-water shiploading facilities are available close to the beneficiation plants. Figure 1 shows a flowsheet of the general operation. Pelletizing operations are scheduled 24 hours a day and 365 days per year. A maximum tonnage rate with a high percentage of operating time is necessary to produce the three and one half million tons per year required from the two pellet lines. Process control is a major responsibility and of primary concern to all Operating personnel. The particle size, moisture, and chemical composition of the filter cake must be closely controlled to get uniform high-grade pellets. Key points are sampled routinely and analyzed on a two-hour basis to provide the necessary structure and chemical data to maintain a superior final product. The iron content of the pellets is held between 65.3 and 65.8 percent with 4.0 percent Si02. Sulfur is below 0.04 percent and copper is below 0.02 percent in the finished pellet.

Jan 1, 1968