Search Documents

By B. Basim

Novel chemicals that can be used for increasing the efficiency of fine coal dewatering were developed at Virginia Tech. Reagent A was tested on three different coal samples in laboratory vacuum filtration tests. These included flotation products from Middle Fork plant, Elkview Mining Company, and CONSOL, Inc. The tests conducted with the Middle Fork coal sample (100 mesh x 0) showed that cake moisture can be reduced by more than 10% beyond what can be achieved without using dewatering aid. This improvement was achieved at 1 lb/ton of Reagent A and 0.1 inch cake thickness. At 0.5 inches of cake thickness, the improvement was limited to 8% at the same reagent dosage. The results obtained with the Elkview coal (28 mesh x 0) showed similar advantages in using the novel dewatering aid. Depending on the reagent dosage, cake thickness, drying cycle time and temperature, it was possible to reduce the cake moisture to 12 to 14% range. In addition to achieving lower cake moisture, the use of Reagent A substantially decreased the cake formation time, indicating that the reagent improves the kinetics of dewatering. The test results obtained with CON SOL coal were not as good as with the other coals tested in the present work, which may be attributed to possible oxidation and/or contamination.

Jan 1, 1998

By R. A. Basse, W. D. Diment, A. J. Petrina

INTRODUCTION In 1957, diamond drilling on a magnetic anomaly indicated an extensive zone of copper mineralization on what is now the Craigmont Mines property. By mid¬1958, drilling established a copper ore body. Milling commenced in September 1961 at 4536 t/d (5000 stpd) and by the end of October 1977 the mine had produced 339 662.04 t (374,363.9 st) of copper. At present, two-thirds of the mill feed is derived from underground operations and one-third from low-grade surface stockpiles. Craigmont Mines is situated 209 km (130 air miles) northeast of Vancouver (see Fig. 1), 16 km (10 miles) west of the town of Merritt, a logging, ranching, and mining community of about 7000 people. It is serviced by paved highways, Canadian Pacific Railway, British Columbia Hydro, and Inland Natural Gas Co. Water is pumped from the Nicola River, a distance of 6 km (4 miles) and a lift of 244 m (800 ft). In March 1967, the open pit mining operations at Craigmont Mines reached their economic limit and were suspended. Before this, it had been decided that a sub¬level caving method of underground mining would be used to supply ore to the concentrator after the cessation of open pit production. This chapter describes the fac¬tors influencing the choice of mining method, some of the problems encountered, mining practices, and results. GEOLOGY The ore bodies of upper Triassic age are located in a limy horizon striking east-west, closely paralleling the intrusive Guichon batholith, bounded on the south by rhyolites and on the north by graywackes, and dipping steeply to the south (Figs. 2a, b). The ore bodies are relatively narrow with a maxi¬mum width of 79 m (260 ft), a combined strike length of 853 m (2800 ft), and a vertical extent of 610 m (2000 ft). Chalcopyrite is virtually the only copper mineral, and 20% of the ore zone consists of acid solu¬ble magnetite and hematite. The area has been subjected to considerable faulting and brecciation, which is a major factor in the mining operation. Total geological reserves, at 0.7% Cu cutoff, for the deposit were 22 316 743 t (24,600,000 st) at 1.89% Cu. An additional 5 236 270 t (5,772,000 st) at 0.6% Cu were mined from the open pit. Ground Conditions The waste rocks-graywacke, andesites, and diorite -are relatively incompetent due to the high degree of fracturing and jointing, and all require varying degrees of support. The ore zones are somewhat less fractured; ground support is still required, however, although to a lesser extent than in the country rock. Ground conditions in the main ore body are better than in the smaller, nar¬rower ore bodies. Clayey fault gouge is present in most of the faults; gouge zones may be up to 6 or 9 m (20 or 30 ft) wide. The main ground problems are associated with local weakness rather than pressure. Shape of Ore Bodies (Figs. 2a, b and 3a, b) The main No. 1 ore body is approximately 244 m (800 ft) long and 46 m (150 ft) wide. It extends ver¬tically from the original top of the open pit at 4200 ele¬vation to just below the 3060 level. The No. 2 ore body is approximately 304 m (1000 ft) long, varies from stringer width at the extremities up to 79 m (260 ft) wide, and extends from 3060 level to 2400 level. Both these ore bodies have extensions re¬sulting in additional small irregular bodies. Ore bodies are mostly steep dipping, though part of the Wing ore body, an extension of No. 2 ore body, dips at 0.87 rad (50'). This ore body varies in size, but is approximately 122 m (400 ft) long, 21 m (70 ft) wide, and about 213 m (700 ft) high. No. 1 Limb ore body is a narrow extension of the No. I Main with a vertical extent of 137 m (450 ft), average width of 18 ft (60 ft), a strike length of 152 m (500 ft), and dips steeply at 1.4 rad (80°). No. 1 East is an eastern extension of the No. 1 Main with a vertical extent of 183 m (600 ft), a strike length of 91 m (300 ft), an average width of 30 m (100 ft), and dips at 1.2 to 1.4 rad (70 to 80°). No. 1 South is at the upper west end of the open pit with a vertical extent of 76 m (250 ft), a strike length

Jan 1, 1982

By K. A. Brame, L. G. Austin, R. S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-ordering grinding studies in a laboratory ball mill according to the Austin, Klimpel, and Luckie procedures. The results were scaled to five larger mills of 0.56, 0.82, 8.36, 4.41, and 5 m in diameter assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distributions and capacities for batch grinding in the smaller mills and open-circuit grinding in the larger mills. The predicted capacities were in approximate agreement with experimental values except for the 5-m diam mill. The Bond method gave capacity predictions that were 4570 to 150% too high.

Jan 1, 1987

By Kenneth E. Merklin

The heavy media process is now being used extensively throughout the world for the gravity concentration of a great number of different minerals. The process is a commercial adaptation of the heavy liquid procedure which has been used in laboratories for many years to separate mineral of different specific gravities. In the heavy media process, a suspension of finely divided particles in water is used to increase the apparent specific weight of the fluid to the desired separating point. The original heavy media process used sand, galena, pyrite and occasionally other materials as the solid constituent of the separating suspensions. As the process developed, the need for a more universal media meeting the following requirements was recognized: 1. High specific gravity. 2. Resistance to abrasion. 3. Resistance to corrosion, 4. Readily reduced to a suitable size consist for suspension in water. 5. Available in quantity at economical price levels. 6. Easy to recover by a simple method.

Jan 1, 1958

By Hou Xilun

Three production methods of rapid cold bonding and low temperature bonding pellets using sponge iron powder as a binder have been successfully developed. These methods differ from ordinary bonding method by no addition of salt and other catalyzers, no corrosion of equipment and no pollution of environment. Mechanism of pellet bonding is studied. Experiment shows that these pellets have good metallurgical properties. A semi-industrial test has proven the laboratory results, with the production of metallic pellets continuous and stable. These methods are substituted for traditional high temperature firing of oxidized pellets in direct reduction. As a result, the plant for oxidized pellets can be saved and substituted for grate in the grate-kiln system. Thus, 20% of the investment could be saved. Production cost may also be decreased. The production of cold bonding pellets does not need additional area.

Jan 1, 1980

By G. R. Hart

The expected 1990 Clean Air legislation is providing electric utilities with a series of challenges and decisions as the utilities prepare strategies to comply with the resulting regulations. This paper addresses the strategy development of a coal-based utility --the legislation, the process used, the fuel issues, the options available, and the decisions to be made.

Jan 1, 1991

Sedimentation is used to clarify process effluents or to thicken process slurries. The sedimentation cycle of a suspension is presented as a settling curve. This curve is simply a plot of the height of the interface between the settled suspension and clear liquor versus time. Figure 1 shows a series of graduate cylinders which contain a suspension at various stages in its settling cycle. Cylinder 1 shows the suspension completely mixed at time zero. After a brief period of time (see cylinder 2), the suspension is observed to settle from its initial height Ho to height H1, leaving behind a volume of clear (or turbid) liquor, called the supernatant. The interface between the supernatant and suspension is termed the mud line. It is also possible to distinguish at the bottom of the cylinder a layer of sludge representing solids which have settled from the suspension. The interface between it and the suspension is called the sludge line. The sludge line moves upward in the cylinder.

Jan 1, 1992

By J. B. Hiskey

The principle oxide minerals of molybdenum are wulfenite (PbMoO4), ferrimolybdite (Fe2(MOO 4)3.nH2O), powellite (CaMoO4), and ilsemannite (Mo304). Wulfenite is found in Arizona, New Mexico, Nevada, Utah, California, and Montana. It is also found in the states of Sonora and Chihuahua, Mexico. Prior to 1915 wulfenite ores were the primary source of molybdenum. The solubility of wulfenite in hot sodium sulfide was first noted by Bonardi(1) during attempts to sulfidize wulfenite material prior to flotation. He identified lead sulfide and soluble sodium molybdate as reaction products. Bacon (2) sulfidized wulfenite in preparation for flotation and by X-ray analysis found the reaction product to be lead sulfide. Holmes(3) made an extensive investigation of the extraction of molybdenum from wulfenite concentrates by leaching. Nearly 100% molybdenum extraction was possible from -100 mesh samples leached for 15 min with 10% sodium sulfide solution at room temperature. Molybdenum extraction from -100 mesh samples after leaching 30 min at a temperature of 45°C using 2, 4, and 6% sodium sulfide was about 32, 79, and 98% respectively. The extraction showed little sensitivity to time, temperature, or particle size using 10" sodium sulfide solution.

Jan 1, 1976

By Y. C. Kim, M. Preston, F. Martino

Because of the high cost of obtaining coal washability samples, it has been difficult in the past to obtain washability variograms. As a result, it could not be determined if the geostatistical prediction tool known as kriging can be applied to predict in situ coal washability characteristics. This paper presents the obtained variogram models for the Upper Freeport coal seam in western Pennsylvania. Variogram model parameters are presented for a total of 27 models. They are for four different variables: float- weight, ash, sulfur, and Btu, at seven different specific gravities: 1.275, 1.300, 1.325, 1.400, 1.600, 1.800, and 1.80,Sink. Based on the obtained variogram results, it can be con¬cluded that all attributes of coal washability show definite spatial correlation structures, and, consequently, geostatistics can be used to predict the in situ coal washability characteristics.

Jan 1, 1990

By B. K. Parekh

Sludge obtained during production of magnesium (Mg) metal from electrolyzing of molten MgCl2 contains entrapped magnesium particles. The sludge material containing the magnesium particles is a friable, continuous matrix of frozen salt mixture which may also contain some oxides and impurities. A dry process was developed for recovery of magnesium metal from the sludge, utilizing minerals beneficiation unit operations. The steps included selective comminution, screening, attritioning and tabling. Recovery of the high grade (+90 percent) metal was in the 70 percent range. The process is being commercially used in the U.S. The novel process was also successfully applied to a magnesium-alloy for recovery of metal from the sludges.

Jan 1, 1995

By R. N. Browne

As man searches unexplored horizons for new and economic industry, he must be constantly and acutely aware of the presence or absence of that precious commodity without which Industry, indeed Man himself, could not survive --W ATE R. The water requirements of the world today are magnanimous, considering that in 1960 the estimated consumption in the united States was over 300 billion GPD (1) or more than 1,700 GPD per person (5). The magnitude of the problem can be visualized as one considers that three times this quantity of water will be required in the united States by the year 2 000, when the dependable supplies of water are estimated to be only two-thirds of that required(2). How, then, can we continue to wreak such havoc on that life-sustaining substance -W ATE R? It is necessary, indeed mandatory, that those engaged in the Engineering profession consider it their moral obligation, not only to conserve the quantity of water which their conceived projects may require, but also to treat the effluent in order that the eutro-phication of natural water courses not be abnormally accelerated. The International Nickel Company of Canada Limited consumes some 33-1/2 millions of gallons of fresh water daily at its nine town-sites, fourteen mines and eight plants throughout the Sudbury district of Ontario. The present daily reuse of water exceeds 100 millions of gallons in the same area. It is noteworthy to mention that the milling rate has increased from 46,000 to 70,000 tons per day during the past five years, with no increase in water consumption. In fact, there has been a reduction in fresh water requirements.

Jan 1, 1971

By Dale R. Andrus

Why is there such an increased thrust toward positive multiple use land management and where will it lead? History and purpose of the mining law of 1872. John Marshall discovered gold at Sutter?s mill near Coloma, California, on January 19, 1848, and utter chaos resulted. The great migration of people to the undeveloped western lands had begun. Prior to this discovery, copper, lead, and iron had been the minerals for which the laws were made. With this discovery of gold on the public domain, it became apparent that congressional legislation was necessary. This became even more apparent as each of the numerous mining districts which were springing up in California, and elsewhere in the west adopted local miners' customs to regulate their activities. Although these early miners acted under mining district rules and in some cases state regulations, they were, in reality, appropriating minerals without sanction of federal law.

Jan 1, 1970

By Kadri Dağdelen, Matthew Deutsch, Thys Johnson

Nested pit analysis in open-pit long range mine planning is used to define approximate ultimate pit limits and an initial high-level schedule in the early stages of a project. Modern ultimate pit optimizers can solve for dozens, or even hundreds, of nested pits however often a smaller subset of pits which are evenly spaced with respect to contained tonnage are desired for downstream analysis. In situations where that pushback selection process must be automated, such as when performing sensitivity analysis, or when the best subset of pushbacks is required; an optimization procedure is warranted. This paper describes a dynamic programming algorithm for selecting pushbacks following nested pit analysis, which is performant and addresses a long-standing inconvenience faced by long range open-pit mine planners.

Jun 25, 2023

By D. -P. Georgescu

A native sulfur mineralization associated with pyrite and iron oxides containing 20% iron was quarried in Calimani Mountains, Oriental Carpathians. The wastes resulted from this exploitation activity, with a volume of 33 millions m3, were stored in four dumps while the wastes resulted from ore processing using flotation and the subsequent treatment were disposed of in a settlement pond. The investigations carried out in the entire mining area focused on the following two aspects: - the impact of environmental factors mainly on the hydrographic network; - the characterization all pollution sources, namely dumps, leachates and the quarry and the assessment of acidic drainage generation. The total sulfur content of the excavated ore was 3.8% while in dumps it ranged between 0.54 and 1.06%. Analysis of samples collected along the hydrographic network, draining the mining area, resulted in pH values ranging between 1.7 and 2.83 as well as high concentration of iron (4525 mg/L to 1.6 mg/L), copper (1.87 mg/L to 0.04 mg/L) and zinc (13.13 mg/L to 0.3 mg/L). Samples from the quarry, the dumps and the tailings pond were analyzed in order to deter-mine: - the maximum potential acidity (MPA); - the acid neutralization capacity (ANC); - the net acid production potential (NAPP).

Jan 1, 2005

By J. H. Desautels

The modern coal mining industry is subject to a vast array of regulations affecting virtually all aspects of its operations. Probably the most significant over-sight role involves the Office of Surface Mining Reclamation and Enforcement (OSH) established by the Surface Mining Control and Reclamation Act, or SHCRA.1 Although complying and coping with SHCRA can be difficult for coal operators, this complex regulatory process has helped insulate the industry from ongoing efforts to extend regulation under the Resource Conservation and Recovery Act, or RCRA, 2 to aspects of the mining industry in general. The Environ-mental Protection Agency (EPA) has struggled with regulation of mining wastes under RCRA since the mid-1970's, but RCRA itself places most coal mining wastes firmly under the control of OSH and SHCRA. Despite the general exemption from RCRA regulation for waste materials that result from extraction and processing of coal itself, there may be circumstances under which coal mining operators could find themselves subject to regulation under RCRA or a number of other statutes administered by EPA. This paper will review briefly the history of mine waste regulation under RCRA, as well as touch on the policy decisions that led to the exemptions from RCRA regulation. The paper will summarize coal waste requirements under SHCRA, and also will review what operations at coal mines need to be controlled, in order to avoid potential liability under RCRA. In addition, it will mention requirements under other federal laws, including CERCLA, or the "Superfund" law,3 and describe how they may impose restrictions or liability on coal operations for waste or other materials commonly found at surface and underground coal mines.

Jan 1, 1993

By D. Buranek, J. G. Wulff, F. W. Gifford

I. INTRODUCTION During the past few years, the state of the art of disposal of solid and liquid waste products from uranium mining and milling operations has experienced some rather interesting and significant changes. Some of these changes have resulted from technological advances in the milling operations and in the engineering aspects of the actual design and construction of the disposal facilities. However, the most significant changes, at least those which have had the greatest impact on the comparative cost and economics of modern disposal systems, have been environmental requirements and regulatory controls, which have become increasingly stringent in recent years. Without delving into the details of the myriad of new laws and regulations which now control the uranium industry, it can be stated with reasonable confidence that one of the principal purposes of more rigid state and federal controls over this industry is the basic desire to promote safer, more reliable and longer term means of effectively controlling and disposing of the potentially objectionable waste products resulting from uranium mining and milling operations. It is difficult to take issue with these basic goals because their need was spawned by past lack of awareness and inattention on the parts of both government and industry to the long term environmental problems and potentially hazardous conditions which can be created by limited planning and ill-conceived or poorly controlled and executed disposal practices. On the other hand, despite the good intentions of those who developed and those who are administering the regulatory controls now in effect, the basic danger exists that overgeneralization of the approach to disposal problems and overrestriction of the potentially acceptable solutions for uranium mine and mill waste disposal could have a significant, adverse economic impact on the mining industry and the ultimate consumers of their products. The regulatory pendulum, which perhaps swung too far toward lack of controls over uranium mill waste disposal in the 1940's, could now well be headed too far in the opposite direction, that is toward over-regulation in the form of restrictions based on technically unrealistic or weakly supportable

Jan 1, 1980

By J. E. Urosek

The Mine safety and Health Administration (MSHA) formed the Mine Ventilation Bleeder and Gob Training Committee in 1993. This committee was charged with developing a training course designed to enhance the knowledge and understanding of practical bleeder ventilation systems. The course will probably include a discussion on the theory behind bleeder system design, an in-depth look at the strengths and weaknesses of the basic bleeder system types, case studies, and a review of the systems currently in use. A database on active underground bituminous coal mines, gob areas, and the bleeder systems presently used was developed from questionnaires distributed to nine Coal Mine Safety and Health (CMS&H) districts. Representative systems were selected for thorough investigation to develop case studies. This paper introduces some of the material to be included in the course, including a description of basic bleeder system designs, a review of a portion of the database, and facts about the gob areas and bleeder systems investigated for the development of case studies.

Jan 1, 1995

By R. H. King

The Deserado Mine of Western Fuels- Utah Inc. installed a micro-computer based mine wide monitoring and control system for mine environment, beltway fire protection, belt operating parameters, and equipment power utilization. The Colorado School of Mines was funded by the U.S. Bureau of Mines to document, evaluate, and report on the system design, procurement, installation, tests, and operation. This paper results from that project. The paper compares planned activities such as installation and start up, procurement contract specifications and system layout with actual performance to develop recommendations for future installations by mine operators.

Jan 1, 1987

By J. F. Cornelsen

Wheel loaders are currently being used in many mining applications for a variety of reasons. While they sometimes provide the lowest loading cost, a primary advantage of the wheel loader versus other loading systems is the increased versatility and mobility inherent in a wheeled vehicle. The advent of large wheel loaders with much greater digging capability enhanced wheel loader usage in severe loading applications. To match these severe conditions, machines offered today were designed to work in these rocky conditions. Soon after the introduction of large wheel loaders into rocky conditions, however, it became apparent to many users that tire costs could at times account for up to 50% of total hourly operating costs on large wheel loaders. In some applications, tire costs alone pushed wheel loader economics beyond the economic feasibility for these jobs, prohibiting their use. In an effort to combat high tire costs, several attempts have been made to put fast moving steel around the tires to provide a strong interface between vehicle and ground. Some earlier attempts involved wrapping tracks around tires. Mechanical difficulties with these systems limited their customer acceptance. Subsequently, the development of protective tire chains came into favor. While tire chains offered added protection to the tires, the cost and maintenance of the chains remains a problem in 1972, the Dystred arrangement was announced for usage on a 6 cu yd wheel loader from Caterpillar Tractor Co. (See Figure 1). The Dystred offered the advantages of greatly increased tread life over conventional tires, as well as resistance to tread puncture in most situations. The arrangement basically employed a track system similar to that used on track type loaders. Pin and bushing wear often caused high hourly operating costs and excessive machine downtime. In addition, the connection of shoes through the use of links, pins, and bushings forced a limitation on too speed of the vehicle.

Jan 1, 1976

By Arne Paus-Jenssen

The potash industry in Saskatchewan has recently been the focus of much new legislation at the provincial level and, along with other mining industries in Canada, also subject to changes in tax legislation at the federal level. As a result, the industry presently operates under (a) provincial production controls, a prorationing scheme; (b) a new provincial reserve tax on potash only and; (c) a new federal income tax applicable to all mineral industries. The prorating scheme dates back to 1970 and emerged as public policy because of the excess supply situation faced by the international potash industry towards the end of the sixties. This caused special problems for new mines in Saskatchewan and the provincial government decided to intervene. The new tax legislation at provincial and federal levels, both introduced within the last four years, reflects a belief that insufficient revenues accrue to the public sector from natural resources. All mining industries in Canada, including the potash industry, have had their tax positions completely reversed during these four years. Traditionally the mining sector in Canada has been a recipient of substantial tax incentives and has enjoyed low tax rates. This has changed and the mining sector is now one of the most heavily taxed sectors in the economy. In addition, the mining sector has moved from a situation where its rapid development was favoured by governments to a situation where this is no longer the case.

Jan 1, 1976