Search Documents

By B. Barry, M. S. Klima

"Testing was conducted to evaluate the effects of hydroacoustic cavitation (HAC) treatment on two bituminous coal slurries and the subsequent separation of each slurry in a classifying hydrocyclone. HAC treatment was performed using a pilot-scale circuit fabricated by Furness-Newburge Inc. The circuit was designed to induce cavitation by means of flow through an ultrasonic resonator chamber or enhanced cavitation by initial flow through a cavitation chamber followed by flow through the ultrasonic chamber. The test materials were nominal -1,500-micron and -150-micron Illinois-basin bituminous coal slurries, which were obtained from an operating coal preparation facility. After 5 sec of HAC treatment, the median size of the -1,500-micron material was reduced, with ash values for certain size fractions decreasing more than 5 percent compared with untreated samples. Extending treatment time led to greater degradation of the +1,180-micron material and an increase in the -25-micron material, with ash reductions occurring for material in the -850+150-micron size range. Size degradation was less for the -150-micron material. Subsequent separation of the treated slurries was carried out in a hydrocyclone with diameter of 102 mm. HAC treatment led to a decrease in the ash value and an increase in the heating value of the underflow stream compared with the feed material. For example, the ash value was reduced by about 16 percent for the -1,500-micron material and 25 percent for the -150-micron material with heating value increases of 7 and 33 percent, respectively, after HAC treatment. Overall, HAC treatment appeared to have a slight effect on the size selectivity curves.IntroductionUltrasound in the range of 20 to 1,000 kHz, referred to as power ultrasound, consists of high energy waves that can create zones of compression and expansion when used to irradiate liquids (Frederick, 1965; Leighton, 1994; Mason and Lorimer, 1988). This action generates varying pressure regions leading to cavitation or the formation, growth and near-immediate collapse of microscopic voids or bubbles (Frederick 1965; Leighton 1994; Mason and Lorimer 1988). Collapse occurs when the bubble reaches critical size and cannot absorb additional sound field energy, and the critical size is governed by the ultrasound frequency (Shchukin et al., 2011)."

Jan 1, 2015

By Ven Mercade

The flotation of calcite has been studied by many investigators, especially in terms of type of collector; pH; and metal ions that activate and, more importantly, depress the flotation of calcite (1)(2). Research was extended to the investigation of the effect of polyvalent metal salts and sodium silicate using these materials added separately or in mixtures (3)(4)(5)(6). Flotation of calcite was also studied with respect to its function as a carrier in the beneficiation of kaolin clays by Ultraflotation (7) (8) (9). The carrier used in Engelhard Minerals & Chemicals Corporation's industrial Ultraflotation operation is calcite. This fact, coupled with the continuing interest in Ultraflotation phenomena, led to a study to determine the effect of polyvalent metal-silicate hydrosols on the flotation of calcite.

Jan 1, 1978

By Harold J. Schock

This paper describes an experimental method for the monitoring of diesel-generated exhaust gas pollutants in a dead-ended drift for the purpose of assessing the effect of control approaches. Experiments were conducted to determine the relative merits of these ventilation configurations: no auxiliary ventilation, induction ventilation at the entrance to the drift, and ventilation of the dead-ended drift with positive displacement tubing. The drift used in this experimental work was approximately 105 ft. (32.0 mf long and slightly downsloping, with an average height and width of 8 ft. (2.4 m) and 28 ft. (8.5 m1 , respectively. The data were gathered for assessing these ventilation methods and for gathering data to support a computer model of the dispersion and mixing processes. For this drift, it was found that ventilation with positive displacement tubing provided the best removal of diesel-generated pollutants. Induction ventilation appeared to be the least effective of the three methods examined. A comparison was also made between personal monitoring and area monitoring. Results of this analysis showed that in regions of high concentration gradients, it was not possible to get good agreement between point sampling and personal monitoring. In well-mixed areas, good agreement between the two methods of monitoring was obtained.

Jan 1, 1980

By Farzad Moradpouri, Kianoush Barani, M. R. Azadi

The aim of this paper is to assess the effect of microwave treatment on copper sulfide ore for ball milling and bed breakage. Liberation analysis of ground products in eight size fractions showed that microwave pretreatment liberated more chalcopyrite particles from the bed breakage product than the ball mill product. In bed breakage, microwave pretreatment caused a 2% increase in chalcopyrite liberation on average. Microwave pretreatment produces more elongated particles in ball milling and more rounded particles in bed breakage, respectively. Microwave pretreatment produces coarser chalcopyrite particles with a wide range of sizes. This effect is more significant in bed breakage compared with ball milling. Micro-flotation test results showed that in ball milling, treated and untreated materials have similar metallurgical performance and there is a little difference (1%) between the average Cu recovery values. However, in bed breakage, the average recovery for the treated materials is about 5% higher than the untreated materials.

Jul 8, 2021

By H. Sevim

Mining engineering curriculum has been discussed and debated in meetings and conferences, and opinions and recommendations have been published in the literature since the inception of the official degree-granting mining engineering program at the Columbia School of Mines in 1864. The deliberations have usually been heightened during the periods of boom-and-bust cycles experienced by the mining industry since the 1920s. Currently, the global natural resource industry is undergoing another cycle, called ?super cycle,? characterized by elevated prices for metals and other natural resources. The super cycle is occurring as a result of the large deficit between the global supply and demand for natural resources, due, in large part, to economic expansion and development in countries such as China, India and Brazil. Because of this cycle, there is a shortage of mining engineers in the U.S., Canada and Australia.

Jan 1, 2012

By V. R. Bovino

In the early 80's, the cover of a major weekly magazine proclaimed the "Death of Mining." A few years ago, mining conventions, similar to this, around the country sported the theme, "The Survival of Mining." Today, the SME announces that "Mining is Alive." Being part of an industry that is simply alive is not very exciting. We can do better! Our challenge must be to flourish, blossom, maximize our potential and expand our horizons. The pace of rejuvenating this industry is still woefully inadequate. The new generation of mining industry leaders recognizes the urgent need for bold operational changes?changes in the way we deal with our employees? changes in the way we achieve productivity? and changes in the way we reward our employees for productivity.

Jan 1, 1991

By V. K. Reddy Kallam, NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

The study investigates SO2 leaching of low-grade ferruginous manganese ores to selectively recover manganese as MnSO4 and produce battery-grade electrolytic manganese dioxide (EMD). The effects of leaching parameters (duration, temperature, SO2 flow rate) on Mn recovery were studied. Under optimum conditions, 97.9% Mn recovery was achieved. The MnSO4 leach liquor was purified and used for electrowinning EMD with 88.01% purity and battery-active γ structure.

Apr 20, 2022

By Alejandro Gutiérrez, David Ahues, Paola Merino, Felipe González

The semiautogenous grinding (SAG) mill is one of the most important pieces of equipment in the comminution of materials. Its objective is to reduce the size of the ore until the ore can be released and continue on its transformation process. Although it is a simple process that involves impact, abrasion and attrition, its energy consumption is extremely high and inefficient, with no more of 17 percent of the energy supplied going toward size reduction. This gives rise to an important challenge because any improvement generates great economic benefits.

By D. R. Tweeton

A modified push-pull field test and a computer model of cation exchange were developed to aid in evaluating cation exchange parameters prior to in situ mining. Reliable determination of these parameters is essential when modeling restoration of groundwater quality. The field test involves a much larger volume and much less disturbance to the ore sample than is feasible with laboratory measurements. This test can be performed in two or three weeks. It is relatively inexpensive, requiring one injection- production well and two or more wells for collecting samples of leach solution. The use of the model in interpreting test results is illustrated with field data from an in situ uranium mine. Much of the research was performed by the University of Texas at Austin, and was partially funded by the Bureau of Mines.

Jan 1, 1986

By Shawn McWilliams, Aini Sun, Mike Lichte, Greg Colzani

The Allegheny County Sanitary Authority (ALCOSAN) adopted its Clean Water Plan (CWP) in May 2020, as part of a federal consent decree to comply with the USEPA’s Combined Sewer Overflow (CSO) Control Policy. Planned improvements include constructing a new regional storage/conveyance tunnel system, promoting green infrastructure/ source control, and expanding the treatment plant. Preliminary planning for the tunnel system was completed in October 2020. The Ohio River Tunnel (ORT) project is the first of three tunnel projects that make up the regional tunnel system. The ORT project began final design in 2021. This paper discusses the advancements made to the ORT preliminary planning concepts considering property availability, alignment optimization, tunnel boring machine evaluation, contract packaging and delivery schedules.

Jun 13, 2023

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Sometimes standing supports are used as a tool to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for different types of standing supports (steel and timber) to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. In this paper, the mine roof simulator (MRS), at the NIOSH Pittsburgh research facility, was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. To justify the testing program for testing standing supports with end-conditions of rock-like materials, the verified prop models were used to study the effect of a wide range of roof and floor materials (gray shale, shale, and claystone) on the critical buckling loads of the steel props. Also, several lateral loading scenarios were evaluated in which the steel props were laterally loaded at different heights. The critical buckling load for steel props setting up against a claystone roof and floor was found to be one-half of that shown by the MRS test where roof and floor platens are made of steel. Minimum prop performance was observed when the lateral load was applied at the mid-height of the steel prop, especially at small lateral displacement (less than 2 in).

Sep 10, 2022

By J. Hindman, E. Moeller

Vermiculite is currently mined from shallow (less than 25 m or 80 ft) surface deposits throughout the world. The largest producers are Palabora Mining of Phalabowra, South Africa (ore stock is a phlogopitemica), Xinjiang Yuli Xinlong Vermiculite of Korla, China, and W.R. Grace of Enoree, SC (ore stock is a biotite mica). Smaller operations are in Australia, Brazil, Russia and Zimbabwe. They also produce vermiculite on a continuous basis but do not export any significant amounts of product to North America. Intermittent and poorly documented production on a minor scale is reported from Argentina, Egypt, India and Uganda. Worldwide vermiculite production in 2004 increased1.7 percent to 432.8 kt (477,000 st). North American production declined, while African and Chinese production continued to increase.

Jan 1, 2005

By T. Patten

A method for stabilizing mercury containing waste for landfill disposal would be a very cost effective solution for industry. A mercury polythiocarbonate material which is made via a metallurgical process passes a traditional TCLP for mercury. The mercury polythiocarbonate material was subjected to a more thorough evaluation, the Integrated Leaching procedures as described in Kossan (1) and Sanchez (2)The procedure involves leaching the mercury polythiocarbonate material at varying pH and sample size to liquid. The procedure had to be adapted for small sample sizes and finely divided materials due to the product characteristics and available material. The leachates were evaluated and found to be stable within common environmental pH values. The performance details on how Inter-Mountain Labs met the leaching requirements of the procedures and the analysis of mercury are presented.

Jan 1, 2012

By Eduardo Velasco, Paz Navarro, Alfonso Navarro, Claudio Cimiotti, Alejandro Sanz, Nick Karlin

The LA Effluent Outfall tunnel is a 7-mile long, 18' internal diameter, secondary treated effluent discharge tunnel currently under construction by Dragados USA for the Los Angeles County Sanitation District No. 2 (LACSD). The purpose of this tunnel is to add redundancy and increased capacity for discharge of secondary treated effluent from the LACSD’s Joint Water Pollution Control Plant, located in Wilmington, California within Southern Los Angeles County. Current discharge from this facility flows through two existing tunnels of 8' and 12' horseshoe profile, constructed in 1937 and 1958, respectively. When the new tunnel is complete, it will add an additional capacity of 670MGD in peak wet weather flow conditions. Geology of the roughly 7 mile long tunnel was divided into six reaches by the contract documents. Tunnel Reaches (TR) 1 to 3, comprising 19,550' will be excavated in alluvial sands of the San Pedro and Lakewood formations, with cover ranging from 45 to 90 feet. In this reach the tunnel intersects the seismically active Palos Verdes fault Zone. TR 4 is a 1,600' transitional zone between alluvium and the rock formations of the Palos Verdes (PV) Hills, comprised mostly of Malaga Mudstone. TR’s 5 and 6 total 15,591', and are within the rock formations of the PV Hills with overburden ranging from 315' to 475'. The primary constituent of the PV Hills is Altamira

Jun 13, 2021

By Amanda Powers, Brian Glynn, Robert Sauceda, Daniel Huffines, Mike Garbeth

This paper will review the evaluation performed for the Cottonwood & Hackberry Creek Wastewater Interceptor Improvements Project to replace two separate aging and undersized interceptor sewers by either open cut construction or trenchless construction methods. A case study will be discussed for the utilization of microtunneling to avoid a deep open cut excavation within a landscaped roadway median to construct nearly a mile of new 60-inch interceptor sewer in an urban area adjacent to an environmentally sensitive riverine area, while minimizing the permitting and environmental impacts of construction, and minimizing the impacts to residents and vehicular trafc and restoration reuirements.

Jun 23, 2024

By A. Bascetin

Materials produced in quarries have been used for different intentions such as concrete and cement raw material, asphalt and embankment aggregates, railway ballast. Especially in cement manufacturing, the chemical composition and the uniformity of the raw materials play a strategic role in the economy and quality of the cement process. Therefore, it is necessary to achieve uniformity and desired chemical composition and maintain these at all production stages according to the type of cement produced. To achieve this goal the production planning and pit design play an essential role. This paper briefly outlines the production optimization of cement raw materials in a quarry in Istanbul western part of Turkey. For the purpose it was used the 3D ore body modeling and the geostatistical techniques. The variation of chemical components (%CaO, %Al2O3, %Fe2O3 etc.) and quality control parametres (LSF, SR, AR and etc.) obtained from the quarry were determined. Then the values of unknown chemical components and quality control parameters in the ore body were estimated using Kriging which is one of the geostatistical interpolation methods. The open pit design was also created by specifying wall slopes and taking into consideration of the grade distributions of the benches. The most important revolution in the paper is investigating the effects of the block dimensions in block modelling which is important for reserve estimation. The other important point in the study is using the different range values in variogram analysis for determination optimal reserve estimation. n this study, the effects of two parametres on reserve and waste amount estimation were determined according to CaO% distribution. The study was pointed out that the changing of the two parameters are very important for the optimal mine planning and environmental considerations.

Jan 1, 2010

By V. T. McLemore

In-situ leaching (ISL) operations have been proposed to recover uranium from sandstone-uranium deposits in NM. ISL (also known as in-situ recovery, solution mining, solution-leach mining, leach mining) consists of injecting a leaching solution into the mineralized zone through injection wells. The leach solution migrates through the formation, dissolves uranium and is recovered through production wells. The uranium is then precipitated through a conventional uranium recovery system. Several criteria must be met in order for in-situ leaching to be successful, most important is that the ore body must be amenable to chemical leaching. A number of ISL operations have been conducted in NM in the past (Mobil, Crownpoint; UNC-Teton, Section 23; Grace Nuclear, Hook?s Ranch, Seboyeta, Church Rock; Anaconda, Windwhip). Kerr-McGee (later Quivera Mining Co., Rio Algum) successfully produced uranium from mine-water recovery (recirculated mine water) from the Ambrosia Lake mines (mid-1960s to 2002). Despite some difficulties, ISL is a viable alternative to recovering uranium and could be utilized in the Grants district with proper aquifer characterization and monitoring.

Jan 1, 2009

By Ü. Atalay, G. Alaeddinoglu, G. Özcengiz, G. Özbayoglu, Z. Özdemir

In this study, bacterial pre-treatment was applied before cyanidation in order to enhance the solubilization of silver from Artvin-Kafkasör ore Direct cyanidation process was found inefficient to recover silver from the ore. Only 40.36% silver recovery was obtained with direct cyanidation while silver recoveries of above 60% were obtained after bacterial treatment. Thiobacillus ferrooxidans was used as the microorganism in pretreatment tests. Effects of various parameters such as pulp density, duration, inoculum size and particle size on silver recovery have been investigated in this study.

Jan 1, 2001

By H. Lawrence

In 1977, the Bureau of Mines awarded a grant to the State of South Carolina to explore the possibility of using Landsat multispectral scanner (MSS) data as an aid in monitoring surface mining activities in selected counties of the State. Work had been done in Aiken County prior to the grant by Bureau of Mines and State personnel at the EROS Data Center using both the GE Image 100 and ESL IDIMS systems. The initial work on the 1-100 consisted of locating and measuring the areas of various kaolin mines. The results were excellent on location, identification, and accurate area measurements of several mines as compared with aerial photos of each mine. The effort also included locating and measuring the size of all mines (including sand and gravel) within two U.S. Geological Survey (USGS) 7 ½ min quadrangle maps. Line printer overlays using the IDIMS equipment and software resulted in the location of all known mines within an estimated error less than ±91.4m (5300 feet). Mine acreage was calculated by counting each symbol (which represented one pixel) and multiplying by 1.1 (the number of acres per pixel). Figure 1 shows a portion of one quadrangle overlay. Table I gives a comparison of acreage measured for sever- al mines from the 1-100 and IDIMS systems vs. aerial photo measurements.

Jan 1, 1979

By A. A. Schweizer

This paper documents the growth and projects the future of Green Diamond Sand Products. Since1954, Green Diamond, located in Riddle, Oregon, has been producing sand from granulated nickel slag for use in various markets. Through the years, the company has seen several changes from its ownership to its product lines. In 1991, Green Diamond was producing abrasive sand at a rate of about 30,000 tons per year. It was at this time that Green Diamond became part of Glenbrook Nickel Company. Over the next eight years, Green Diamond would quadruple its production to over 140,000 tons while moving into three new markets, as well. Green Diamond is now producing sand for use in the abrasive, foundry, construction, and roofing industries. In 1998, Green Diamond again found itself under new, private ownership. With plans on developing agricultural sand and spent abrasives recycling, the future of Green Diamond appears to be one of further expansion coupled with diversification of its product lines.

Jan 1, 2000